ER2000FCT~ER2006FCT ISOLATION SUPERFAST RECOVERY RECTIFIER VOLTAGE 50 to 600 Volts 20 Amperes CURRENT FEATURES • Plastic package has Underwriters Laboratory Flammability Classification 94V-O. Flame Retardant Epoxy Molding Compound. • Exceeds environmental standards of MIL-S-19500/228 • Low power loss, high efficiency. • Low forwrd voltge, high current capability • High surge capacity. • Super fast recovery times, high voltage. • Epitaxial chip construction. • In compliance with EU RoHS 2002/95/EC directives MECHANICALDATA • Case: ITO-220AB Molded plastic .027(.67) .022(.57) • Terminals: Lead solderable per MIL-STD-750, Method 2026 • Polarity: As marked. • Standard packaging: Any • Weight: 0.55 ounces, 1.56 grams. MAXIMUM RATING AND ELECTRICAL CHARACTERISTICSS Ratings at 25°C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% PARAMETER SYMBOL ER2000FCT ER2001FCT ER2001AFCT ER2002FCT ER2003FCT ER2004FCT ER2006FCT UNITS Maximum Recurrent Peak Reverse Voltage VR R M 50 100 150 200 300 400 600 V Maximum RMS Voltage VR M S 35 70 105 140 210 280 420 V Maximum DC Blocking Voltage VD C 50 100 150 200 300 400 600 V Maximum Average Forward Current at Tc=100o C IF (A V ) 20 A Peak Forward Surge Current : 8.3ms single half sine-wave superimposed on rated load(JEDEC method) IF S M 150 A Maximum Forward Voltage at 10A VF Maximum DC Reverse Current TJ =25 O C at Rated DC Blocking VoltageTJ =100 O C IR Maximum Reverse Recovery Time (Note 2) trr Typical Junction capacitance (Note 1) CJ 85 Typical thermal Resistance (Note 3) RθJ c 3.0 TJ ,TS T G -50 to +150 Operating Junction and Storage Temperature Range 0.95 1.3 1.7 V 1 500 35 µA 50 ns pF O C/W O C NOTES: 1. Measured at 1 MHz and applied reverse voltage of 4.0 VDC. 2. Reverse Recovery Test Conditions: I F=.5A, IR=1A, Irr=.25A. 3. Both Bonding and Chip structure are available. STAD-JUN.05.2009 1 PAGE . 1 ER2000FCT~ER2006FCT 20 16 12 6 RESISTIVEORINDUCTIVE LOAD 4 0 0 20 40 60 80 100 120 140 160 INSTANTANEOUS FORWARD CURRENT AMPERES AVERAGE FORWARD CURRENT, AMPERES RATING AND CHARACTERISTIC CURVES 50 50-200V 10 300-400V 1.0 600V O T J= 25 C Pulse Width=200us 0.1 0 .8 1.2 1.0 . 1.4 1.6 1.8 O CASE TEMPERAURE, C INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig.2- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTIC Fig.1- FORWARD CURRENT DERATING CURVE O TJ= 125 C 100 180 PEAK FORWARD SURGE CURRENT, INVSTANTANEOUS REVERSE CURRENT, MICROAMPERES 1000 O TJ= 75 C 10 150 8.3ms Single Half Since-Wave JEDEC Method 120 90 60 25 0 1 2 5 10 20 50 100 NO. OF CYCLE AT 60HZ 1.0 O TJ= 25 C Fig.4- MAXIMUM NON - REPETITIVE SURGE CURRENT 0.1 20 40 60 80 100 120 90 PERCENT OF RATED PEAK INVERSE VOLTGE, VOLTS 80 FIG.3 TYPICAL REVERSE CHARACTERISTICS CAPACITANCE, pF 70 60 O TJ = 25 C 50 40 30 20 10 1 2 5 10 20 50 100 200 500 REVERSE VOLTAGE, VOLTS Fig.5- TYPICAL JUNCTION CAPACITANCE STAD-JUN.05.2009 1 PAGE . 2