Document 333-1 SMT Power Inductors - LPO6610 Series • Very low profile - only 1.0 mm high! • Handles current up to 1.7 Amps rms Designer’s Kit C367 contains 3 each of all values Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 91.0 – 95.0 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 1000/7″reel Plastic tape: 12 mm wide, 0.3 mm thick, 8 mm pocket spacing, 1.2 mm pocket depth PCB washing Only pure water or alcohol recommended Part number1 L2 DCR ±20% max (µH) (Ohms) LPO6610-122ML_ 1.2 0.08 LPO6610-152ML_ 1.5 0.10 LPO6610-222ML_ 2.2 0.12 LPO6610-332ML_ 3.3 0.16 LPO6610-472ML_ 4.7 0.20 LPO6610-682ML_ 6.8 0.32 LPO6610-103ML_ 10 0.41 LPO6610-153ML_ 15 0.55 LPO6610-223ML_ 22 0.85 LPO6610-333ML_ 33 1.3 LPO6610-473ML_ 47 1.8 LPO6610-683ML_ 68 2.5 LPO6610-104ML_ 100 3.5 LPO6610-154ML_ 150 5.0 LPO6610-224ML_ 220 7.0 LPO6610-334ML_ 330 15.0 SRF typ (MHz) 190 140 115 90 88 66 55 42 38 29 22 18 14 12 10 8 1. When ordering, please specify termination and packaging codes: Isat3 (A) 2.1 1.9 1.6 1.3 1.1 0.90 0.80 0.65 0.50 0.40 0.35 0.30 0.25 0.18 0.16 0.13 Irms4 (A) 1.7 1.5 1.4 1.2 1.1 0.85 0.75 0.60 0.52 0.42 0.36 0.30 0.26 0.21 0.18 0.13 LPO6610-334MLC Termination: L = RoHS compliant silver-palladium-platinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (1000 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. 2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc using an Agilent/HP 4263B LCR meter or equivalent. 3. DC current at which the inductance drops 10% (typ) from its value without current. 4. Current that causes a 40°C temperature rise from 25°C ambient. 5. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 Document 333-1 Revised 10/15/08 Document 333-2 SMT Power Inductors - LPO6610 Series Typical L vs Frequency Typical L vs Current 1000 1000 100 µH Inductance (µH) Inductance (µH) 100 µH 100 100 10 µH 10 10 µH 10 1.2 µH 1.2 µH 1 1 0.1 0.1 0.01 1 0.1 10 0.01 10 Current (A) Irms Derating Dash number 0.270 6,90 XXX 120 110 X 100 90 0.100 2,50 0.150 3,80 0.185 4,70 Internal code 80 0.040 ±0.004 1,00 ±0,10 70 Recommended Land Pattern 60 50 0.192 4,90 40 25°C Percent of rated Irms 1 0.1 Frequency (MHz) 30 0.029 0,750 20 0.216 max 5,50 10 0.100 2,54 0.134 3,40 0 -40 -20 0 20 40 60 80 100 120 140 Ambient temperature (°C) 0.260 max 6,60 Dimensions are in inches mm Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 Document 333-2 Revised 10/15/08