Memory ICs BR9080AF-W / BR9080ARFV-W / BR9080ARFVM-W / BR9016AF-W / BR9016ARFV-W / BR9016ARFVM-W 8k, 16k bit EEPROMs for direct connection to serial ports BR9080AF-W / BR9080ARFV-W / BR9080ARFVM-W / BR9016AF-W / BR9016ARFV-W / BR9016ARFVM-W The BR9080A and BR9016A series are serial EEPROMs that can be connected directly to a serial port and can be erased and written electrically. Writing and reading is performed in word units, using four types of operation commands. Communication occurs though CS, SK, DI, and DO pins, WC pin control is used to initiate a write disabled state, enabling these EEPROMs to be used as one-time ROMs. During writing, operation is checked via the internal status check. !Applications Movie, camera, cordless telephones, car stereos, VCRs, TVs, DIP switches, and other battery-powered equipment requiring low voltage and low current !Features 1) BR9080AF-W / ARFV-W / ARFVM-W (8k bit) : 512 words ×16 bits BR9016AF-W / ARFV-W / ARFVM-W (16k bit) : 1024 words × 16bits 2) Single power supply operation 3) Serial data input and output 4) Automatic erase-before-write 5) Low current consumption Active (5V) : 5mA (max.) Standby (5V) : 3µA (max.) 6) Noise filter built into SK pin 7) Write protection when VCC is low Inhibition on inadvertant write with the WC pin. 8) SOP8 / SSOP-B8 / MSOP8 9) High reliability CMOS process 10) 100,000 ERASE / WRITE cycles 11) 10 years Data Retention 1/12 BR9080AF-W / BR9080ARFV-W / BR9080ARFVM-W / BR9016AF-W / BR9016ARFV-W / BR9016ARFVM-W Memory ICs !Block diagram R/B INSTRUCTION DECODE CS CONTROL DETECT SUPPLY VOLTAGE CLOCK GENERATION WRITE DISABLE SK INSTRACTION REGISTER DI ∗ ADD BUFFER DATA REGISTER DO ADD DECORDER 9bit R/W AMPS 16bit HIGH VOLTAGE GENERATOR WC ∗ ∗ 9bit 8,192 bit EEPROM 16bit ∗ BR9016A is 10bit, 16,384bit BR9080A is 9bit, 8,192bit !Pin descriptions VCC R/B WC GND WC CS SK DI DO R/B BR9080ARFVM : MSOP8 BR9016ARFVM GND DO VCC CS DI VCC SK CS BR9080AF : SOP8 BR9016AF R / B WC GND SK DI DO BR9080ARFV : SSOP-B8 BR9016ARFV Fig.1 Pin No. Pin name Function MSOP / SSOP SOP 1 3 CS Chip Select Control 2 4 SK Serial Data Clock Input 3 5 DI Op code, address, Serial Data Input 4 6 DO Serial Data Output 5 7 GND Ground 0V 6 8 WC Write Control Input 7 1 R/B READY / BUSY Output 8 2 VCC Power supply 2/12 Memory ICs BR9080AF-W / BR9080ARFV-W / BR9080ARFVM-W / BR9016AF-W / BR9016ARFV-W / BR9016ARFVM-W !Absolute maximum ratings (Ta=25°C) Parameter Symbol Limits −0.3∼+7.0 VCC Supply voltage Power dissipation Pd SOP8 450∗1 SSOP-B8 300∗2 MSOP8 310∗3 V mW −65∼+125 °C Topr −40∼+85 °C − −0.3∼VCC+0.3 V Storage temperature Tstg Operation temperature Input voltage Unit ∗1 Reduced by 4.5mW for each increase in Ta of 1°C over 25°C. ∗2 Reduced by 3.0mW for each increase in Ta of 1°C over 25°C. ∗3 Reduced by 3.1mW for each increase in Ta of 1°C over 25°C. !Recommended operating conditions (Ta=25°C) Parameter Power supply voltage Symbol WRITE VCC READ Input voltage VIN Min. Typ. Max. Unit 2.7 − 5.5 V 2.7 − 5.5 V 0 − VCC V 3/12 Memory ICs BR9080AF-W / BR9080ARFV-W / BR9080ARFVM-W / BR9016AF-W / BR9016ARFV-W / BR9016ARFVM-W !Electrical characteristics BR9080AF-W / ARFV-W / ARFVM-W, BR9016AF-W / ARFV-W / ARFVM-W : 5V (Unless otherwise noted, Ta=−40∼85°C, VCC=2.7V∼5.5V) Parameter Symbol Min. Typ. Max. Unit Conditions Input low level voltage 1 VIL1 − − 0.3×VCC V DI pin Input high level voltage 1 VIH1 0.7×VCC − − V DI pin Input low level voltage 2 VIL2 − − 0.2×VCC V CS, SK, WC pin Input high level voltage 2 VIH2 0.8×VCC − − V CS, SK, WC pin IOL=2.1mA IOH=−0.4mA Output low level voltage VOL 0 − 0.4 V Output high level voltage VOH VCC−0.4 − VCC V Input leak current ILI −1 − 1 µA VIN=0V∼VCC Output leak current ILO −1 − 1 µA VOUT=0V∼VCC, CS=VCC ICC1 − − 5 mA fSK=2MHz tE / W=10ms (WRITE) Operating current ICC2 − − 3 mA fSK=2MHz (READ) Standby current ISB − − 3 µA CS / SK / DI / WC=VCC DO, R / B=OPEN SK frequency fSK − − 2 MHz − BR9080AF-W / ARFV-W / ARFVM-W, BR9016AF-W / ARFV-W / ARFVM-W : 3V (Unless otherwise noted, Ta=−40∼85°C, VCC=2.7V∼3.3V) Parameter Symbol Min. Typ. Max. Unit Input low level voltage 1 VIL1 − − 0.3×VCC V DI pin Input high level voltage 1 VIH1 0.7×VCC − − V DI pin Input low level voltage 2 VIL2 − − 0.2×VCC V CS, SK, WC pin Input high level voltage 2 VIH2 0.8×VCC − − V CS, SK, WC pin Output low level voltage VOL 0 − 0.4 V IOL=100µA Output high level voltage VOH VCC−0.4 − VCC V IOH=−100µA Input leak current ILI −1 − 1 µA VIN=0V∼VCC Output leak current ILO −1 − 1 µA VOUT=0V∼VCC, CS=VCC ICC1 − − 3 mA fSK=2MHz tE / W=10ms (WRITE) ICC2 − − 0.75 mA fSK=2MHz (READ) Standby current ISB − − 2 µA CS / SK / DI / WC=VCC DO, R / B=OPEN SK frequency fSK − − 2 MHz Operating current Conditions − Not designed for radiation resistance 4/12 Memory ICs BR9080AF-W / BR9080ARFV-W / BR9080ARFVM-W / BR9016AF-W / BR9016ARFV-W / BR9016ARFVM-W !Operating timing characteristics BR9080AF-W / ARFV-W / ARFVM-W, BR9016AF-W / ARFV-W / ARFVM-W (Unless otherwise noted, Ta=−40∼85°C, VCC=2.7V∼5.5V) Parameter Symbol Min. Typ. Max. Unit CS setup time fCSS 100 − − ns CS hold time tCSH 100 − − ns Data setup time tDIS 100 − − ns Data hold time tDIH 100 − − ns DO rise delay time ns tPD1 − − 150 DO fall delay time tPD0 − − 150 ns Self-timing programming cycle tE / W − − 10 ms CS minimum high level time tCS 250 − − ns READY / BUSY display valid time tSV − − 150 ns Time when DO goes HIGH-Z (via CS) tOH 0 − 150 ns Data clock high level time tWH 230 − − ns Data clock low level time tWL 230 − − ns Write control setup time tWCS 0 − − ns Write control hold time tWCH 0 − − ns !Timing chart Synchronous Data Input Output Timing CS tCS tWH tCSS tCSH tDIH SK tWL tDIS DI tPD tPD tOH DO WC Fig.2 · Input data are clocked in to DI at the rising edge of the clock (SK). · Output data will toggle on the falling edge of the SK clock. · The WC pin does not have any effect on the READ, EWEN and EWDS operations. 5/12 BR9080AF-W / BR9080ARFV-W / BR9080ARFVM-W / BR9016AF-W / BR9016ARFV-W / BR9016ARFVM-W Memory ICs !Circuit operation (1) Command mode BR9080A Start Bit Op Code Address Read (READ) Instruction 1010 100 A0 A1 A2 A3 A4 A5 A6 A7 A8 Write (WRITE) 1010 010 A0 A1 A2 A3 A4 A5 A6 A7 A8 Write enable (WEN) 1010 0011 Write disable (WDS) 1010 0000 ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ Data D0 D1 − D14 D15 ∗ : Means either VIH or VIL Address and data are transferred from LSB. BR9016A Start Bit Op Code Address Read (READ) Instruction 1010 10 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 Write (WRITE) 1010 01 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ Write enable (WEN) 1010 0011 Write disable (WDS) 1010 0000 Data D0 D1 − D14 D15 ∗ : Means either VIH or VIL Address and data are transferred from LSB. (2) Writing enabled / disabled H SK 1 4 12 8 16 L ENABLE = 11 DISABLE = 00 H CS L H 1 DI 0 1 0 0 0 L HIGH-Z DO H R/B WC High or LOW Fig.3 1) When CS is “HIGH” during power up, BR9080AF-W / ARFV-W / ARFVM-W, BR9016AF-W / ARFV-W / ARFVM-W comes up in the write disabled (WDS) state. In order to be programmable, it must receive a write enable (WEN) instruction. The device remains programmable until a disable (WDS) instruction is entered, or until it is powered down. 2) It is unnecessary to add the clock after 16th clock. 6/12 Memory ICs BR9080AF-W / BR9080ARFV-W / BR9080ARFVM-W / BR9016AF-W / BR9016ARFV-W / BR9016ARFVM-W (3) Read cycle BR9080AF-W / ARFV-W / ARFVM-W SK H 4 1 8 16 32 48 L tCS H CS L STANDBY H 0 1 DI 1 0 1 0 0 A1 A0 A7 A8 L HIGH-Z HIGH-Z D0 DO D15 D0 D15 tOH H Read Data (n) R/B Read Data (n+1) High or LOW WC Fig.4 BR9080AF-W / ARFV-W / ARFVM-W BR9016 AF-W / ARFV-W / ARFVM-W SK H 4 1 8 16 32 48 L tCS H CS L STANDBY H 1 DI 0 1 0 1 0 A0 A1 A2 A8 A9 L HIGH-Z HIGH-Z D0 DO D15 D0 D15 tOH H Read Data (n) R/B WC Read Data (n+1) High or LOW Fig.5 BR9016AF-W / ARFV-W / ARFVM-W 1) After the fall of the 16th clock pulse, 16-bit data is output from the DO pin in synchronization with the falling edge of the SK signal. (DO output changes at a time lag of tPD0, tPD1 because of internal circuit delay following the falling edge of the SK signal. During the tPD0 and tPD1 timing, the tPD time should be assured before data is read, to avoid the previous data being lost. See the synchronized data input / output timing chart in Fig.2.) 2) The data stored in the next address is clocked out of the device on the falling edge of 32nd clock. The data stored in the upper address every 16 clocks is output sequentially by the continual SK input. Also the read operation is reset by CS High. 7/12 BR9080AF-W / BR9080ARFV-W / BR9080ARFVM-W / BR9016AF-W / BR9016ARFV-W / BR9016ARFVM-W Memory ICs (4) Write cycle BR9080AF-W / ARFV-W / ARFVM-W SK H 1 4 8 16 32 L H CS L tCS H 0 1 DI 1 0 0 1 0 A0 A1 A7 A8 D0 D15 L HIGH-Z HIGH-Z DO tSV tE-W H R/B tWCS WC tWCH Fig.6 BR9080AF-W / ARFV-W / ARFVM-W BR9016 AF-W / ARFV-W / ARFVM-W SK H 1 4 8 16 32 L H CS L tCS H 1 DI 0 1 0 0 1 A0 A1 A2 A8 A9 D0 D15 L HIGH-Z HIGH-Z DO tSV tE-W H R/B WC tWCS tWCH Fig.7 BR9016AF-W / ARFV-W / ARFVM-W 1) At the rising edge of 32nd clock, R / B pin will be come out “LOW” after the specified time delay (tSV). 2) From above edge R / B will indicate the ready / busy status of the chip: “LOW” indicated programming is all in progress: “HIGH” indicates the write cycle is complete and this part is ready for another instruction. 3) During the input of Write command, CS must be “LOW”. However, once the write operation started, CS could be either “HIGH” or “LOW”. 4) If WC becomes “HIGH” during Write Cycle, the write operation is halted. In this case, the address data in writing is no guaranteed. It is necessary to rewrite it. 8/12 Memory ICs BR9080AF-W / BR9080ARFV-W / BR9080ARFVM-W / BR9016AF-W / BR9016ARFV-W / BR9016ARFVM-W (5) READY / BUSY display (R / B pin and DO pin: BR9080AF-W / ARFV-W / ARFVM-W, BR9016AF-W / ARFV-W / ARFVM-W) 1) This display outputs the internal status signal; the R / B pin outputs the HIGH or LOW status at all times. The display can also be output from the DO pin. Following completion of the writing command, if CS falls while SK is LOW, either HIGH or LOW is output. (The display can also be output without using the R / B pin, leaving it open.) 2) When writing data to a memory cell, the READY / BUSY display is output from the rise of the 32nd clock pulse of the SK signal after tSV, from the R / B pin. R / B display = LOW: writing in progress (The internal timer circuit is activated, and after the tE / W timing has been created, the timer circuit stops automatically. Writing of data to the memory cell is done during the tE / W timing, during which time other commands cannot be received.) R / B display = HIGH: command standby state (Writing of data to the memory cell has been completed and the next command can be received.) CS SK Clock DI Write command tPD tOH HIGH-Z READY DO HIGH-Z BUSY R/B READY BUSY READY Fig.8 R / B Status Output timing chart 1) DO will output R / B status after CS is held low during SK=L, until CS is held high. Note : The document may be strategic technical data subject to COCOM regulations. 9/12 BR9080AF-W / BR9080ARFV-W / BR9080ARFVM-W / BR9016AF-W / BR9016ARFV-W / BR9016ARFVM-W Memory ICs !Operation notes (1) Turning the power supply on and off 1) When the power supply is turned on and off, CS should be set to HIGH (=VCC). 2) When CS is LOW, the command input reception state (active) is entered. If the power supply is turned on in this state, erroneous operations and erroneous writing can occur because of noise and other factors. To avoid this, make sure CS is set to HIGH (=VCC) before turning on the power supply. (Good example) Here, the CS pin is pulled up to VCC. When turning off the power supply, wait at least 10msec before turning it on again. Failing to observe this condition can result in the internal circuit failing to be reset when the power supply is turned on. (Bad example) CS is LOW when the power supply is turned on or off. In this case, because CS remains LOW, the EEPROM may perform erroneous operations or write erroneous data because of noise or other factors. * Please be aware that the case shown in this example can also occur if CS input is HIGH-Z. VCC VCC GND VCC CS GND Good example Bad example Fig.9 (2) Noise countermeasures 1) SK noise If noise occurs at the rise of the SK clock input, the clock is assumed to be excessive, and this can cause malfunction because the bits are out of alignment. 2) WC noise During a writing operation, noise at the WC pin can be erroneously judged to be data, and this can cause writing to be forcibly interrupted. 3) VCC noise Noise and surges on the power supply line can cause malfunction. We recommend installing a bypass capacitor between the power supply and ground to eliminate this problem. 10/12 BR9080AF-W / BR9080ARFV-W / BR9080ARFVM-W / BR9016AF-W / BR9016ARFV-W / BR9016ARFVM-W Memory ICs (3) Canceling modes 1) Read commands 32 Clock SK CS DI Start bit Operating code Address 4 bits 4 bits 8 bits 16 bits DO DO Data D15 Cancel can be performed for the entire read mode space WC HIGH or LOW Fig.10 Cancellation method: CS HIGH 2) Write commands 32 Clock SK CS DI Start bit Operating code Address 4 bits 4 bits 8 bits DO Data D15 16 bits tE / W R/B a b c d WC Fig.11 Canceling methods a : Canceled by setting CS HIGH. The WC pin is not involved. b : If the WC pin goes HIGH for even a second, writing is forcibly interrupted. Cancellation occurs even if the CS pin is HIGH. At this point, data has not been written to the memory, so the data in the designated address has not yet been changed. c : The operation is forcibly canceled by setting the WC pin to HIGH or turning off the power supply (although we do not recommend using this method). The data in the designated address is not guaranteed and should be written once again. d : If CS is set to HIGH while the R / B signal is HIGH (following the tE / W timing), the IC is reset internally, and waits for the next command to be input. 11/12 BR9080AF-W / BR9080ARFV-W / BR9080ARFVM-W / BR9016AF-W / BR9016ARFV-W / BR9016ARFVM-W Memory ICs !External dimension (Units : mm) BR9080ARFVM-W BR9016ARFVM-W BR9080AF BR9016AF 5.0 ± 0.2 0.9Max. 0.75±0.05 0.08±0.05 5 1 4 0.15 ± 0.1 4.4 ± 0.2 8 +0.05 0.145−0.03 0.22+0.05 −0.04 0.65 6.2 ± 0.3 4 0.08 M 0.11 1 0.475 1.5 ± 0.1 5 0.29±0.15 0.6±0.2 8 2.8±0.1 4.0±0.2 2.9±0.1 1.27 0.4 ± 0.1 0.3Min. 0.08 S 0.15 MSOP8 SOP8 BR9080ARFV BR9016ARFV 8 5 1 4 0.22 ± 0.1 (0.52) 0.15 ± 0.1 0.1 1.15 ± 0.1 4.4 ± 0.2 6.4 ± 0.3 3.0 ± 0.2 0.3Min. 0.65 0.1 SSOP-B8 12/12 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document use silicon as a basic material. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.0