Coilcraft JA4372 Flyback transformer Datasheet

Document 816
Flyback Transformers
For TI TPS23754
PoE Interface
• Developed for Texas Instruments TPS23754 High Power, High
Efficiency PoE Interface and DC/DC Controller
• Input: 33 – 57 V
• 1500 Vrms isolation from primary and bias to secondary
Core material Ferrite
Terminations RoHS tin-silver (96.5/3.5) over tin over nickel over
phos bronze.
Weight 12.0 g
Ambient temperature –40°C to +125°C
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 175 per 13″ reel Plastic tape: 44 mm wide,
0.4 mm thick, 28 mm pocket spacing, 11.9 mm pocket depth
PCB washing Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf
L at 0 A2 L at Ipk3
DCR max (Ohms)4
Turns ratio6 Part
±10%
min
Leakage L5
number1
(µH)
(µH)
pri
sec
bias drive max (µH) pri : sec pri : bias pri : drive
JA4372-AL_
JA4387-AL_
75
75
67.5
66.0
0.143 0.0045 0.122 0.072
0.077 0.0098 0.096 0.070
1. When ordering, please specify a packaging code:
JA4387-ALD
Packaging: D = 13″ machine ready reel. EIA-481 embossed plastic
tape (175 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter D instead.
2. Inductance is measured at 250 kHz, 0.1 Vrms, 0 Adc.
3. Peak primary current drawn at minimum input voltage.
3.0
0.756
1 : 0.08
1 : 0.25
1 : 0.28
1 : 0.25
1 : 0.16
1 : 0.15
Ipk3
(A)
Output7
2.2
2.2
3.3 V, 7.6 A
12 V, 2.08 A
4. DCR for the primary and the secondary is measured with windings
connected in parallel.
5. Leakage inductance is for the primary, measured with the windings
connected in parallel and the secondary windings shorted.
6. Turns ratio is with the primary windings and secondary windings connected in parallel.
7. Output is with the secondary windings connected in parallel. Output of the
drive winding is 6 V, 10 mA. Output of the bias winding is 11.2 V, 20 mA.
8. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Primary windings and secondary
windings to be connected in parallel
on PC board
Dimensions are in
inches
mm
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
Document 816
Revised 10/09/13
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.
Similar pages