Kingbright APT1608SECK-J3-PRV Low power consumption Datasheet

1.6X0.8mm SMD CHIP LED LAMP
Part Number: APT1608SECK/J3-PRV
Hyper Red
Features
Description
z 1.6mmX0.8mm SMT LED, 0.75mm thickness.
The Hyper Red device is based on light emitting diode chip
z Low power consumption.
made from AlGaInP.
z Wide viewing angle.
z Ideal for backlight and indicator.
z Package: 2000pcs / reel .
z Moisture sensitivity level : level 3.
z RoHS compliant.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.004") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAN0479
REV NO: V.2A
DATE: APR/09/2015
PAGE: 1 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203013843
Selection Guide
Part No.
Dice
APT1608SECK/J3-PRV
Iv (mcd) [2]
@ 20mA
Lens Type
Hyper Red (AlGaInP)
Viewing
Angle [1]
Min.
Typ.
700
1100
*200
*350
2θ1/2
120°
Water Clear
Notes:
1. θ1 / 2 is the angle from optical centerline where the luminous intensity is 1 / 2 of the optical peak value.
2. Luminous intensity / luminous Flux: + / -15%.
* Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
Hyper Red
λD [1]
Dominant Wavelength
Δλ1/2
Max.
Units
Test Conditions
640
nm
IF=20mA
Hyper Red
625
nm
IF=20mA
Spectral Line Half-width
Hyper Red
20
nm
IF=20mA
C
Capacitance
Hyper Red
27
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
Hyper Red
2.2
2.8
V
IF=20mA
IR
Reverse Current
Hyper Red
10
uA
VR = 5V
Notes:
1. Wavelength: + / -1nm.
2. Forward Voltage: + / -0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Hyper Red
Units
Power dissipation
84
mW
DC Forward Current
30
mA
Peak Forward Current [1]
150
mA
5
V
Reverse Voltage
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
Note:
1. 1 / 10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAN0479
REV NO: V.2A
DATE: APR/09/2015
PAGE: 2 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203013843
RED
Hyper Red
APT1608SECK/J3-PRV
SPEC NO: DSAN0479
REV NO: V.2A
DATE: APR/09/2015
PAGE: 3 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203013843
APT1608SECK/J3-PRV
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAN0479
REV NO: V.2A
DATE: APR/09/2015
PAGE: 4 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203013843
PACKING & LABEL SPECIFICATIONS
APT1608SECK/J3-PRV
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAN0479
REV NO: V.2A
DATE: APR/09/2015
PAGE: 5 OF 5
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Q.M.Chen
ERP: 1203013843
Similar pages