DGNJDZ HER607 6.0 amp high efficiency rectifier Datasheet

HER601
THRU
HER608
6.0 AMP HIGH EFFICIENCY RECTIFIERS
VOLTAGE RANGE
50 TO 1000 Volts
CURRENT
6.0 Amperes
FEATURES
* Low forward voltage drop
* High current capability
* High reliability
* High surge current capability
* High speed switching
R-6
.360(9.1)
.340(8.6)
DIA.
0.945(24.0)
MIN.
MECHANICAL DATA
* Case: Molded plastic
* Epoxy: UL 94V-0 rate flame retardant
* Lead: Axial leads, solderable per MIL-STD-202,
method 208 guranteed
* Polarity: Color band denotes cathode end
* Mounting position: Any
* Weight: 1.65 grams
* Both normal and Pb free product are available:
* Normal:80~95%Sn,5~20%Pb
* Pb free:99 Sn above can meet Rohs enviroment substance
directive request
.360(9.1)
.340(8.6)
0.945(24.0)
MIN.
.052(1.3)
.043(1.1)
DIA.
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating 25 C ambient temperature uniess otherwies specified.
Single phase half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
TYPE NUMBER
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current
HER601 HER602 HER603 HER604 HER605 HER606 HER607 HER608
50
100
200
300
400
600
800
1000
35
50
70
100
140
200
210
300
280
400
420
600
560
800
700
1000
.375"(9.5mm) Lead Length at Ta=50 C
Peak Forward Surge Current, 8.3 ms single half sine-wave
300
1.3
10.0
1.0
at Rated DC Blocking Voltage
Ta=100 C
Maximum Reverse Recovery Time (Note 1)
Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range TJ, TSTG
1.70
200
50
75
-55
NOTES:
1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A
2. Measured at 1MHz and applied reverse voltage of 4.0V D.C.
72
100
+150
V
V
V
A
6.0
superimposed on rated load (JEDEC method)
Maximum Instantaneous Forward Voltage at 6.0A
Maximum DC Reverse Current
Ta=25 C
UNITS
A
V
µA
µA
nS
pF
C
RATING AND CHARACTERISTIC CURVES (HER601 THRU HER608)
FIG.1-TYPICAL FORWARD
FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE
CHARACTERISTICS
-H
HE
R6
06
R6
HE
AVERAGE FORWARD CURRENT,(A)
08
ER
6
-6
04
R6
01
05
-6
03
10.0
HE
1.0
6
Single Phase Half Wave 60Hz
Resistive Or Inductive Load
5
Ground Plane
4
1" X 1" Copper
surface area
3
PC BOARD
Recommended
2
PC BOARD
PC Board
Mounting
Standard PC Board
1
Mounting
0
20
40
Tj=25 C
60
80
100
120
140
160
180
200
AMBIENT TEMPERATURE ( C)
Pulse Width 300us
1% Duty Cycle
.1
.01
.2
.4
.6
.8
1.0
1.2
1.4
1.6
FORWARD VOLTAGE,(V)
FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE
RECOVERY TIME CHARACTERISTICS
50Ω
NONINDUCTIVE
10Ω
NONINDUCTIVE
( )
(+)
D.U.T.
25Vdc
(approx.)
PULSE
GENERATOR
(NOTE 2)
( )
1Ω
NONINDUCTIVE
OSCILLISCOPE
(NOTE 1)
PEAK FORWAARD SURGE CURRENT,(A)
FIG.4-MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
500
400
300
Sine Wave
200
JEDEC method
100
0
1
|
|
|
|
|
|
|
|
0
-0.25A
1cm
100
175
150
125
100
75
50
25
0
-1.0A
50
10
FIG.5-TYPICAL JUNCTION CAPACITANCE
2. Rise Time= 10ns max., Source Impedance= 50 ohms.
+0.5A
5
NUMBER OF CYCLES AT 60Hz
NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF.
trr
8.3ms Single Half
Tj=25 C
(+)
JUNCTION CAPACITANCE,(pF)
INSTANTANEOUS FORWARD CURRENT,(A)
100
0.1
SET TIME BASE FOR
0.5
1
2
5
10
20
REVERSE VOLTAGE,(V)
50 / 10ns / cm
73
50
100
200
500
1000
Similar pages