LM140QML LM140QML Three Terminal Positive Regulators Literature Number: SNVS382A LM140QML Three Terminal Positive Regulators General Description The monolithic 3-terminal positive voltage regulators employ internal current-limiting, thermal shutdown and safe-area compensation, making them essentially indestructible. If adequate heat sinking is provided, they can deliver over 0.5A output current. They are intended as fixed voltage regulators in a wide range of applications including local (on-card) regulation for elimination of noise and distribution problems associated with single-point regulation. In addition to use as fixed voltage regulators, these devices can be used with external components to obtain adjustable output voltages and currents. Considerable effort was expended to make the entire series of regulators easy to use and minimize the number of external components. It is not necessary to bypass the output, although this does improve transient response. Input bypassing is needed only if the regulator is located far from the filter capacitor of the power supply. Features ■ ■ ■ ■ ■ Complete specifications at 1.0A and 0.5A loads No external components Internal thermal overload protection Internal short circuit current-limiting Output transistor safe-area compensation Ordering Information NS Part Number NS Package Number Package Description LM140H-5.0/883 SMD Part Number H03A 3LD TO-39 Metal Can LM140H-12/883 H03A 3LD TO-39 Metal Can LM140H-15/883 H03A 3LD TO-39 Metal Can LM140K-5.0/883 K02C 2LD TO-3 Metal Can LM140K-12/883 K02C 2LD TO-3 Metal Can LM140K-15/883 K02C 2LD TO-3 Metal Can Connection Diagrams Steel Metal Can TO-39 Package (H) TO-3 Metal Can (K) 20155402 Bottom View See NS Package Number K02C 20155401 Bottom View See NS Package Number H03A © 2008 National Semiconductor Corporation 201554 www.national.com LM140QML Three Terminal Positive Regulators April 3, 2008 LM140QML Absolute Maximum Ratings (Note 1) DC Input Voltage Internal Power Dissipation (Note 2) Maximum Junction Temperature (TJmax) Storage Temperature Range 35V Internally Limited 150°C -65°C ≤ TA ≤ +150°C -55°C ≤ TA ≤ +125°C 300°C Operating Temperature Range Lead Temperature (Soldering 10 seconds) Thermal Resistance θJA T0−39 (Still Air) T0−39 (500 LF/Min Air Flow) T0−3 (Still Air) T0−3 (500 LF/Min Air Flow) 232°C/W 77°C/W 35°C/W TBD θJC T0−39 T0−3 ESD Susceptibility (Note 3) 15°C/W 4°C/W 2KV Quality Conformance Inspection MIL-Std-883, Method 5005 - Group A Subgroup Description 1 Static tests at Temp °C +25 2 Static tests at +125 3 Static tests at -55 4 Dynamic tests at +25 5 Dynamic tests at +125 6 Dynamic tests at -55 7 Functional tests at +25 8A Functional tests at +125 8B Functional tests at -55 9 Switching tests at +25 10 Switching tests at +125 11 Switching tests at -55 12 Settling time at +25 13 Settling time at +125 14 Settling time at -55 www.national.com 2 LM140QML LM140H–5.0 Electrical Characteristics DC Parameters The following conditions apply, unless otherwise specified. DC: VI = 10V, IL =350mA Symbol VO RLine RLoad Parameter Output Voltage Line Regulation Load Regulation Conditions Notes VI = 35V, IL = 5mA Quiescent Current ΔIQ Quiescent Current Change IPk Peak Current VDO Dropout Voltage IOS Short Circuit Current Max Unit Subgroups 4.75 5.75 V 1 4.80 5.20 V 1 VI = 8V 4.70 5.30 V 1, 2, 3 VI = 8V, IL = 5mA 4.70 5.30 V 1, 2, 3 VI = 20V, IL = 5mA 4.70 5.30 V 1, 2, 3 VI = 20V 4.70 5.30 V 1, 2, 3 7V ≤ VI ≤ 25V, IL = 200mA -50 50 mV 1 8V ≤ VI ≤ 25V, IL = 200mA -50 50 mV 2, 3 8V ≤ VI ≤ 20V, IL = 200mA -25 25 mV 1 -40 40 mV 2, 3 5mA ≤ IL ≤ 500mA 5mA ≤ IL ≤ 200mA IQ Min -50 50 mV 1 -100 100 mV 2, 3 -25 25 mV 1 -50 50 mV 2, 3 7.0 mA 1, 2, 3 8V ≤ VI ≤ 25V, IL = 200mA -0.8 0.8 mA 1, 2, 3 5mA ≤ IL ≤ 350mA -0.5 0.5 mA 1, 2, 3 0.4 2.0 A 1, 2, 3 2.5 V 1 1.0 A 1, 2, 3 Max Unit Subgroups dB 4, 5, 6 VI - VO = 7V (Note 4) (Note 5) VI = 35V AC Parameters The following conditions apply, unless otherwise specified. AC: VI = 10V, IL =350mA Symbol RR Parameter Ripple Rejection Conditions IL = 125mA, eI = 1VRMS, ƒ = 2.4KHz, VI = 10V 3 Notes Min 62 www.national.com LM140QML LM140H–12 Electrical Characteristics DC Parameters The following conditions apply, unless otherwise specified. DC: VI = 19V, IL =350mA Symbol VO RLine RLoad Parameter Output Voltage Line Regulation Load Regulation Conditions Notes VI = 35V, IL = 5mA Quiescent Current ΔIQ Quiescent Current Change IPk Peak Current VDO Dropout Voltage IOS Short Circuit Current Max Unit Subgroups 11.4 12.6 V 1 11.5 12.5 V 1 VI = 15.5V 11.4 12.6 V 1, 2, 3 VI = 15.5V, IL = 5mA 11.4 12.6 V 1, 2, 3 VI = 27V, IL = 5mA 11.4 12.6 V 1, 2, 3 VI = 27V 11.4 12.6 V 1, 2, 3 14.5V ≤ VI ≤ 30V, IL = 200mA -60 60 mV 1 15.0V ≤ VI ≤ 30V, IL = 200mA -120 120 mV 2, 3 16V ≤ VI ≤ 25V, IL = 200mA -30 30 mV 1 -60 60 mV 2, 3 -120 120 mV 1 -240 240 mV 2, 3 -60 60 mV 1 -120 120 mV 2, 3 5mA ≤ IL ≤ 500mA 5mA ≤ IL ≤ 200mA IQ Min 7.0 mA 1, 2, 3 14.5V ≤ VI ≤ 30V, IL = 200mA -0.8 0.8 mA 1, 2, 3 5mA ≤ IL ≤ 350mA -0.5 0.5 mA 1, 2, 3 0.4 2.0 A 1, 2, 3 2.5 V 1 1.0 A 1, 2, 3 Max Unit Subgroups dB 4, 5, 6 VI - VO = 7V (Note 4) (Note 5) VI = 35V AC Parameters Symbol RR Parameter Ripple Rejection www.national.com Conditions VI = 17V, IL = 125mA, eI = 1VRMS, ƒ = 2.4KHz 4 Notes Min 55 LM140QML LM140H–15 Electrical Characteristics DC Parameters The following conditions apply, unless otherwise specified. DC: VI = 23V, IL =350mA Symbol VO RLine RLoad Parameter Output Voltage Line Regulation Load Regulation Conditions Notes VI = 35V, IL = 5mA Quiescent Current ΔIQ Quiescent Current Change IPk Peak Current VDO Dropout Voltage IOS Short Circuit Current Subgroups 14.25 15.75 V 1 Max 14.40 15.60 V 1 VI = 18.5V 14.25 15.75 V 1, 2, 3 VI = 18.5V, IL = 5mA 14.25 15.75 V 1, 2, 3 VI = 30V, IL = 5mA 14.25 15.75 V 1, 2, 3 VI = 30V 14.25 15.75 V 1, 2, 3 17.5V ≤ VI ≤ 30V, IL = 200mA -60 60 mV 1 18.5V ≤ VI ≤ 30V, IL = 200mA -120 120 mV 2, 3 20V ≤ VI ≤ 30V, IL = 200mA -30 30 mV 1 -60 60 mV 2, 3 -150 150 mV 1 -300 300 mV 2, 3 -75 75 mV 1 -150 150 mV 2, 3 5mA ≤ IL ≤ 500mA 5mA ≤ IL ≤ 200mA IQ Unit Min 7.0 mA 1, 2, 3 17.5V ≤ VI ≤ 30V, IL = 200mA -0.8 0.8 mA 1, 2, 3 5mA ≤ IL ≤ 350mA -0.5 0.5 mA 1, 2, 3 0.4 2.0 A 1, 2, 3 2.5 V 1 1.0 A 1, 2, 3 Max Unit Subgroups dB 4, 5, 6 VI - VO = 7V (Note 4) (Note 5) VI = 35V AC Parameters The following conditions apply, unless otherwise specified. AC: VI = 23V, IL =350mA Symbol RR Parameter Ripple Rejection Conditions VI=20V, IL=125mA, eI=1VRMS, ƒ = 2.4KHz 5 Notes Min 54 www.national.com LM140QML LM140K–5.0 Electrical Characteristics DC Parameters The following conditions apply, unless otherwise specified. DC: VI = 10V, IL = 5mA Symbol Parameter Conditions Notes Min Max Unit Subgroups 6.0 mA 1 IQ Quiescent Current IL = 1A 7.0 mA 2, 3 ΔQ Quiescent Current Change IL = 1A, 8V ≤ VI ≤ 20mA -0.8 0.8 mA 1 IL ≤ 500mA, 8V ≤ VI ≤ 25V -0.8 0.8 mA 1, 2, 3 5mA, ≤ IL ≤ 1.0A -0.5 0.5 mA 1, 2, 3 VO RLine RLoad IOS Output Voltage Line Regulation Load Regulation 4.80 5.20 V 1 VI = 8V 4.75 5.25 V 1, 2, 3 VI = 8V, IL = 1A 4.75 5.25 V 1, 2, 3 VI = 20V 4.75 5.25 V 1, 2, 3 VI = 20V, IL = 1A 4.75 5.25 V 1, 2, 3 IL = 500mA, 7V ≤ VI ≤ 25V -50 50 mV 1, 2, 3 IL = 1A, 7.3V ≤ VI ≤ 20V -50 50 mV 1 IL = 1A, 8.0V ≤ VI ≤ 20V -50 50 mV 2, 3 IL = 1A, 8V ≤ VI ≤ 12V -25 25 mV 1, 2, 3 5mA ≤ IL ≤ 1.5A -50 50 mV 1 5mA ≤ IL ≤ 1.0A -50 50 mV 2, 3 250mA ≤ IL ≤ 750mA -25 25 mV 1 -4.0 -0.02 A 1 -2.0 -0.02 A 1 Min Max Unit Subgroups dB 4 Current Limit VI = 35V AC Parameters The following conditions apply, unless otherwise specified. AC: VI = 10V, IL = 5mA Symbol RR Parameter Ripple Rejection www.national.com Conditions ƒ = 120Hz, IL = 350mA, eI = 1VRMS 6 Notes 68 LM140QML LM140K–12 Electrical Characteristics DC Parameters The following conditions apply, unless otherwise specified. DC: VI = 19V, IL = 5mA Symbol Parameter Conditions Notes Min Max Unit Subgroups 6.0 mA 1 IQ Quiescent Current IL = 1A 7.0 mA 2, 3 ΔIQ Quiescent Current Change IL = 1A, 15.5V ≤ VI ≤ 27V -0.8 0.8 mA 1 IL = 500mA 15V ≤ VI ≤ 30V -0.8 0.8 mA 1, 2, 3 5mA ≤ IL ≤ 1A -0.5 0.5 mA 1, 2, 3 VO RLine RLoad IOS Output Voltage Line Regulation Load Regulation Current Limit 11.5 12.5 V 1 VI = 15.5V 11.4 12.6 V 1, 2, 3 VI = 15.5V, IL = 1A 11.4 12.6 V 1, 2, 3 VI = 27V 11.4 12.6 V 1, 2, 3 VI = 27V, IL = 1A 11.4 12.6 V 1, 2, 3 IL = 500mA, 14.5V ≤ VI ≤ 25V -120 120 mV 1, 2, 3 IL = 1A, 14.6V ≤ VI ≤ 27V -120 120 mV 1 IL = 1A, 15.0V ≤ VI ≤ 27V -120 120 mV 2, 3 IL = 1A, 16V ≤ VI ≤ 22V -60 60 mV 1, 2, 3 5mA ≤ IL ≤ 1.5A -120 120 mV 1 5mA ≤ IL ≤ 1.0A -120 120 mV 2, 3 250mA ≤ IL ≤ 750mA -60 60 mV 1 VI = 17V -3.5 -0.02 A 1 VI = 35V -2.0 -0.02 A 1 Min Max Unit Subgroups dB 4 AC Parameters The following conditions apply, unless otherwise specified. AC: VI = 19V, IL = 5mA Symbol RR Parameter Ripple Rejection Conditions ƒ = 120Hz, IL = 350mA, eI = 1VRMS 7 Notes 61 www.national.com LM140QML LM140K–15 Electrical Characteristics DC Parameters The following conditions apply, unless otherwise specified. DC: VI = 23V, IL = 5mA Symbol Parameter Conditions Notes Min Max Unit Subgroups 6.0 mA 1 IQ Quiescent Current IL = 1A 7.0 mA 2, 3 ΔIQ Quiescent Current Change IL = 1A, 18.5V ≤ VI ≤ 30V -0.8 0.8 mA 1 IL = 500mA, 18.5V ≤ VI ≤ 30V -0.8 0.8 mA 2, 3 5mA ≤ IL ≤ 1A -0.5 0.5 mA 1, 2, 3 14.4 VO RLine RLoad IOS Output Voltage Line Regulation Load Regulation Current Limit 15.6 V 1 VI = 18.5V 14.25 15.75 V 1, 2, 3 VI = 18.5V, IL = 1A 14.25 15.75 V 1, 2, 3 VI = 30V 14.25 15.75 V 1, 2, 3 VI = 30V, IL = 1A 14.25 15.75 V 1, 2, 3 IL = 500mA, 17.5V ≤ VI ≤ 30V -150 150 mV 1 IL = 500mA, 18.5V ≤ VI ≤ 30V -150 150 mV 2, 3 IL = 1A, 17.7V ≤ VI ≤ 30V -75 75 mV 1 IL = 1A, 20V ≤ VI ≤ 26V -75 75 mV 1, 2, 3 5mA ≤ IL ≤ 1.5A -150 150 mV 1 5mA ≤ IL ≤ 1.0A -150 150 mV 2, 3 250mA ≤ IL ≤ 750mA -75 75 mV 1 VI = 20V -3.5 -0.02 A 1 VI =35V -2.0 -0.02 A 1 Min Max Unit Subgroups dB 4 AC Parameters The following conditions apply, unless otherwise specified. AC: VI = 23V, IL = 5mA Symbol RR Parameter Ripple Rejection Conditions ƒ = 120Hz, IL = 350mA, eI = 1VRMS Notes 60 Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature), θJA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is PDmax = (TJmax - TA)/ θJA or the number given in the Absolute Maximum Ratings, whichever is lower. Note 3: Human body model, 100pF discharged through 1.5KΩ Note 4: VO is set to 90% VRef Note 5: VDO = VI − VO when VO is 95% of VRef. www.national.com 8 Released 02/21/06 Revision A Section Originator New Release, Corporate format L. Lytle 9 Changes 6 MDS data sheets converted into one Corp. data sheet format. The drift tables were eliminated from the 883 section since it did not apply. MDS data sheets MNLM140-05H Rev 0B0, MNLM140-05-K Rev. 0C0, MNLM140-12H Rev 0A0, MNLM140-12K Rev 0B0, MNLM140-15H Rev 0A0, and MNLM140-15K Rev 0B0 will be archived. www.national.com LM140QML Revision History Section LM140QML Physical Dimensions inches (millimeters) unless otherwise noted Metal Can TO-39 (H) NS Package Number H03A Steel Metal Can Package (K) NS Package Number K02C www.national.com 10 LM140QML Notes 11 www.national.com LM140QML Three Terminal Positive Regulators Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: [email protected] German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: [email protected] National Semiconductor Japan Technical Support Center Email: [email protected] IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated