ICST MK1491-06R Cs5530 geodeâ ¢ clock source Datasheet

CS5530 Geode ™
MK1491-06
Clock Source
Description
Features
The MK1491-06 is a low cost, low jitter, high
performance clock synthesizer for National
Semiconductor CS5530 based computer and
portable appliance applications. Using patented
analog Phase-Locked Loop (PLL) techniques,
the device accepts a 14.318 MHz crystal input to
produce multiple output clocks. It provides
selectable PCI local bus and AC97 audio clocks,
24 MHz and 48 MHz clocks for Super I/O and
USB, as well as multiple Reference outputs.
• Packaged in 28 pin, 300 mil wide SOIC or in
28 pin, 150 mil wide SSOP
• Provides all critical timing for the National
Semiconductor CS5530 Geode companion chip
• Four PCI clocks
• Selectable PCIF on up to 2 outputs
• Early PCI clock selectability
• Up to 4 Reference clocks
• 48 MHz USB and 24MHz SIO support
• AC97 audio clock
• Multiple power down modes
• Low EMI Enable pin reduces EMI radiation on
PCI clocks (patented)
• 3.3 V ±5% operation
The device has multiple power down modes to
reduce power consumption.
Block Diagram
VDD
GND
6
PCI Frequency Select
Low EMI Enable
PCIF Function Enable
Early PCI Enable
5
2
Output
Buffers
PCI
Clocks
SLOW#
PCISTP#
PWRDWN#
Audio Select
3
PCI
Output
Buffer
EPCI/PCI
Audio
Clock
Output
Buffer
16.934 MHz or
24.576 MHz or
49.152 MHz
Fixed
Clocks
Output
Buffer
48 MHz
Output
Buffer
14.318 MHz or
24 MHz
14.3M/24M Select
MUX
XI
14.31818 MHz
crystal
Crystal
Oscillator
Output
Buffers
3
14.318 MHz
XO
MDS 1491-06 F
1
Revision 101700
Printed 11/15/00
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126 • (408)295-9800tel • www.icst.com
MK1491-06
Clock Source
CS5530 Geode ™
Pin Assignment
VDD
XI
XO
GND
14.3M(TS)
14.3M
GND
14.3M(SEL AUDIO)
VDD
SLOW#
GND
FS
SEL24
VDD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PCI Frequency Select Table
28
27
26
25
24
23
22
21
20
19
18
17
16
15
AC97 AUDIO(PEN)
PCI
VDD
24M/14.3M Frequency
PCI
Select Table
PCI
SEL24
24M/14.3M
GND
0
14.31818 MHz
PCI(EPCI#)
1
24.0 MHz
48M(LE#)
VDD
PCIF Enable Control
24M/14.3M
PEN Pin 25
Pin 24
VDD
0
PCI
PCI
GND
PCISTP#
M
PCI
PCIF
PWRDWN#
1
PCIF
PCIF
PCIF continues to run in PCI STOP
mode. See table on page 4.
AC97 Audio Frequency Select
SEL AUDIO
0
M
1
Pin Descriptions
Pin #
Name
1, 9, 14
VDD
2
XI
3
XO
4, 7, 11, 17, 23
GND
5
14.3M(TS)
6
14.3M
8
14.3M(SEL AUDIO)
10
SLOW#
12
FS
13
SEL24
15
PWRDWN#
16
PCISTP#
18, 20, 26
VDD
19
24M/14.3M
21
48(LE#)
22
PCI(EPCI#)
24
PCI
25
PCI
27
PCI
28
AC97 AUDIO(PEN)
Type
P
I
O
P
TI/O
O
TI/O
I
I
I
I
I
P
O
I/O
I/O
O
O
O
TI/O
AC97 AUDIO
16.9344 MHz
24.576 MHz
49.152 MHz
TS
0
0
M
FS
0
1
0
PCI
Tristate all clocks
Reserved
30 MHz
M
1
33.3 MHz
1
0
25 MHz
1
1
37.5 MHz
Early PCI Control Table
EPCI#
0
1
PCI (Pin 22)
1 ns early
Normal
EMI Control
LE#
0
1
PCI Low EMI
ON
OFF
Spread direction is DOWN..
Description
Connect to +3.3V. Must be same voltage on all pins.
Crystal connection. Connect to a 14.31818 MHz crystal or input clock.
Crystal connection. Connect to a 14.31818 MHz crystal, or leave unconnected for clock.
Connect to Ground.
14.318 MHz output. Input control for all clocks per table above.
14.318 MHz buffered reference clock output.
14.318 MHz output and audio frequency select input per table above.
PCI normal or slow mode select input per table on page 4.
Frequency Select for PCI clocks per table above.
Fixed frequency select input per table above. Selects frequency on pin 19.
Power down control; defined in table on page 4.
PCI Stop power down control; defined in table on page 4.
Connect to +3.3V. Must be same voltage on all pins.
Fixed frequency clock output per table above.
Fixed frequency clock output and low EMI (spread spectrum) enable input per table above.
PCI Output clock that can be early. Input control for Early PCI per table above.
PCI Output clock. PCI/PCIF control set by PEN per table above.
PCI Output clock. PCI/PCIF control set by PEN per table above.
PCI Output clock.
Audio clock output and PCIF Function Enable per table above.
Key: I = Input, TI = tri-level input, O = Output, P = Power supply connection, (T)I/O = Input on power up, becomes an Output after 10ms.
Weak internal pull-up resistors are present on SEL24, EPCI#, FS, LE#, PCISTP#, and SLOW#. These pins should be tied to VDD or GND,
and not be left floating. Internal resistors on PEN, SEL AUDIO, and TS pull to a mid-level (M).
MDS 1491-06 F
2
Revision 101700
Printed 11/15/00
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126 • (408)295-9800tel • www.icst.com
CS5530 Geode ™
MK1491-06
Clock Source
Electrical Specifications
Parameter
Conditions
Minimum
Typical
Maximum
Units
7
VDD+0.5
70
260
150
V
V
°C
°C
°C
3.3
3.45
1.4
1.6
0.8
V
V
V
V
V
V
V
mA
µΑ
mA
pF
ABSOLUTE MAXIMUM RATINGS (note 2)
Supply voltage, VDD
Inputs and Clock Outputs
Ambient Operating Temperature
Soldering Temperature
Storage temperature
Referenced to GND
Referenced to GND
-0.5
0
Max of 10 seconds
-65
DC CHARACTERISTICS (VDD = 3.3V unless noted)
Operating Voltage, VDD
Input High Voltage, VIH
Input Mid-Level Voltage, VIM
Input Low Voltage, VIL
Output High Voltage, VOH
Output Low Voltage, VOL
Output High Voltage, VOH
Operating Supply Current, IDD
Power Down mode Supply Current
Short Circuit Current, single output driver
Input Capacitance
3.1
2
1.2
IOH=-8mA
IOL=8mA
IOH=-8mA
No Load, 33.3 MHz
2.4
0.4
VDD-0.4
30
15
±60
7
VDD=3.3V
AC CHARACTERISTICS (VDD = 3.3V unless noted)
Input Frequency
Output Clock Rise Time
Output Clock Fall Time
Output Clock Duty Cycle, all MHz clocks
PCI Output to Output Skew
Skew of EPCI with respect to PCI
Cycle to Cycle Jitter, PCI clocks
EMI reduction, peaks of 5th - 19th odd harmonics
Power up time, PWRDWN# high to all clocks stable
Power on time, applied VDD to all clocks stable
Note:
14.31818
0.8 to 2.0V
2.0 to 0.8V
At 1.5V
Rising edges at 1.5V
33.3 MHz PCI clock
45
49 to 51
1
250
6
8
12
1.5
1.5
55
500
11
20
25
MHz
ns
ns
%
ps
ns
ps
dB
ms
ms
Stresses beyond those listed under Absolute Maximum Ratings could cause permanent damage to the device. Prolonged exposure to levels above the
operating limits but below the Absolute Maximums may affect device reliability.
MDS 1491-06 F
3
Revision 101700
Printed 11/15/00
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126 • (408)295-9800tel • www.icst.com
CS5530 Geode ™
MK1491-06
Clock Source
Power Down Control Table
PCISTP# PWRDWN# SLOW#
MODE
X
0
X
Power Down
0
1
X
PCI STOP
1
1
X
ON
PCI
LOW
LOW
ON
PCIF
LOW
ON
ON
24/14.3 14.3 DESCRIPTION
LOW LOW All outputs low. PLLs and Oscillator off.
ON
ON PCI clocks synchronously enter and leave low state.
ON
ON All Clocks On.
Key: 1 = connected to VDD, 0 = connected to ground, X = any valid logic level, Combination Input/Outputs should be connected to VDD or
Ground through a 10 kΩ resistor as shown below.
Power-On Default Conditions
Input Pin#
5
8
10
12
13
15
16
21
22
28
Function
TS
SEL AUDIO
SLOW#
FS
SEL24
PWRDWN#
PCISTP#
LE#
EPCI#
PEN
Default
M
M
1
1
1
1
1
1
1
M
Condition
All outputs enabled.
Audio clock (pin 28) set to 24.576 MHz
PCI clocks set to 33.3 MHz. Refer to Power Down Control Table above.
PCI frequency = 33.3 MHz.
24M/14.3M (pin 19) set to 24 MHz.
All clocks running.
PCI clocks running.
Low EMI function OFF
Pin 22 set to normal PCI signal (not early).
PCI (pin 25) set to PCI clock (33.33 MHz). PCI (pin 24) set to PCIF clock (33.33 MHz).
External Components
The MK1491-06 requires some inexpensive external components for proper operation. Decoupling capacitors of 0.1µF should be
connected on each VDD pin to ground, as close to the MK1491-06 as possible. A series termination resistor of 33Ω may be used for
each clock output. See the discussion below for other external resistors required for proper I/O operation. The 14.3 MHz oscillator
has internal caps that provide the proper load for a parallel resonant crystal with CL =18 pF. For tuning with other values of CL , the
formula 2*(C L -18) gives the value of each capacitor that should be connected between X1 and ground and X2 and ground.
I/O Structure
33Ω
The MK1491-06 provides more functionality in a 28 pin package by using
a unique I/O technique. The device checks the status of all I/O pins
during power-up and at exit from the Power Down state. This status
(pulled high, low, or mid-level) then determines the frequency selections
and power down modes (see the tables on pages 2 and 4). Within 10ms
after power up, the inputs change to outputs and the clocks start up. In the
diagrams to the right, the 33Ω resistors are the normal output
termination resistors. The 10kΩ resistor pulls low to generate a logic
zero. Weak internal pull-up resistors are present on SEL24, EPCI#, FS,
LE#, PCISTP#, and SLOW#. These pins should be connected directly to
VDD or GND if not under active control. Internal resistors on PEN, SEL
AUDIO, and TS pull to a mid-level (M).
MDS 1491-06 F
4
For select
= 0 (low)
to load*
I/O
10kΩ
Don’t stuff for
“1” selection
*Note: Do not use a TTL load. This will
overcome the 10 kΩ pulldown and force the
input to a logic 1.
Revision 101700
Printed 11/15/00
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126 • (408)295-9800tel • www.icst.com
CS5530 Geode ™
MK1491-06
Clock Source
Package Outline and Package Dimensions
(For current dimensional specifications, see JEDEC Publication No. 95.)
28 pin SOIC
E
Inches
Symbol Min
Max
A
-0.104
A1
0.0040
-B
0.013 0.020
C
0.007 0.013
D
0.697 0.724
E
0.291 0.299
e
.050 BSC
H
0.394 0.419
h
0.01
0.029
L
0.016 0.050
H
INDEX
AREA
1
2
h x 45°
D
A1
e
MDS 1491-06 F
B
Millimeters
Min
Max
-2.65
0.10
-0.33
0.51
0.18
0.33
17.70
18.39
7.40
7.60
1.27 BSC
10.01
10.64
0.25
0.74
0.41
1.27
A
C
L
5
Revision 101700
Printed 11/15/00
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126 • (408)295-9800tel • www.icst.com
CS5530 Geode ™
MK1491-06
Clock Source
Package Outline and Package Dimensions
(For current dimensional specifications, see JEDEC Publication No. 95.)
28 pin SSOP
E1
INDEX
AREA
1
Symbol
A
A1
b
c
D
e
E
E1
L
E
2
Inches
Min
Max
0.053 0.069
0.004 0.010
0.008 0.012
0.007 0.010
0.386 0.394
.025 BSC
0.228 0.244
0.150 0.157
0.016 0.050
Millimeters
Min
Max
1.35
1.75
0.10
0.25
0.20
0.30
0.19
0.25
9.80
10.01
0.65 BSC
5.79
6.20
3.81
3.99
0.41
1.27
D
A1
A
c
e
b
L
Ordering Information
Part/Order Number
MK1491-06R
MK1491-06RTR
MK1491-06S
MK1491-06STR
Marking
MK1491-06R
MK1491-06R
MK1491-06S
MK1491-06S
Low EMI Feature
Yes
Yes
Yes
Yes
Package
Temperature
28 pin SSOP
0 to 70°C
Add Tape & Reel 0 to 70°C
28 pin SOIC
0 to 70°C
Add Tape & Reel 0 to 70°C
While the information presented herein has been checked for both accuracy and reliability, ICS assumes no responsibility for either its use or for the infringement of any patents
or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial
applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not
recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS
product for use in life support devices or critical medical instruments.
Geode is a trademark of National Semiconductor Corporation
MDS 1491-06 F
6
Revision 101700
Printed 11/15/00
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126 • (408)295-9800tel • www.icst.com
Similar pages