ICST ICS252MP Field programmable dual output ss versaclock synthesizer Datasheet

ICS252
Field Programmable Dual Output SS VersaClock Synthesizer
Description
Features
The ICS252 is a low cost, dual-output, field
programmable clock synthesizer. The ICS252 can
generate two output frequencies from 314 kHz to 200
MHz using up to two independently configurable PLLs.
The outputs may employ Spread Spectrum techniques
to reduce system electro-magnetic interference (EMI).
•
•
•
•
•
•
•
•
•
•
•
™
Using ICS’ VersaClock software to configure the PLL
and output, the ICS252 contains a One-Time
Programmable (OTP) ROM to allow field
programmability. Programming features include 4
selectable configuration registers.
The device employs Phase-Locked Loop (PLL)
techniques to run from a standard fundamental mode,
inexpensive crystal, or clock. It can replace multiple
crystals and oscillators, saving board space and cost.
8-pin SOIC package
Two addressable registers
Input crystal frequency of 5 to 27 MHz
Clock input frequency of 3 to 150 MHz
Output clock frequencies up to 200 MHz
Configurable Spread Spectrum Modulation
Operating voltage of 3.3 V
Replaces multiple crystals and oscillators
Controllable output drive levels
Advanced, low-power CMOS process
Available in Pb (lead) free packaging
The device also has a power-down feature that
tri-states the clock outputs and turns off the PLLs when
the PDTS pin is taken low.
The ICS252 is also available in factory programmed
custom versions for high-volume applications.
Block Diagram
VDD
OTP
ROM
with
PLL
Values
SEL
PLL1
PLL2
X1
Divide
Logic
and
Output
Enable
Control
CLK1
CLK2
Crystal
Oscillator
Crystal
X2
GND
External capacitors
are required.
PDTS
1
MDS 252 B
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
Revision 011606
●
tel (408) 297-1201
●
www.icst.com
ICS252
Field Programmable Dual Output SS VersaClock Synthesizer
Pin Assignment
Output Clock Selection Table
SEL
1
8
PDTS
VDD
2
7
GND
X1/ICLK
3
6
CLK2
X2
4
5
CLK1
S1
CLK1 (MHz)
CLK2 (MHz)
Spread
Percentage
0
User
Configurable
User
Configurable
User
Configurable
User
Configurable
User
Configurable
User
Configurable
0
8-pin (150 mil) SOIC
Pin Descriptions
Pin
Number
Pin
Name
Pin
Type
Pin Description
1
SEL
Input
Select pin for frequency selection on CLK1 and CLK2. Internal pull-up resistor.
2
VDD
Power
3
X1/ICLK
XI
Connect to +3.3 V.
Connect this pin to a crystal or external clock input.
4
X2
XO
5
CLK1
Output
Clock1 output. Weak internal pull-down when tri-stated.
Connect this pin to a crystal, or float for clock input.
6
CLK2
Input
Clock2 output. Weak internal pull-down when tri-stated.
7
GND
Power
8
PDTS
Input
Connect this to ground.
Powers down entire chip. Tri-states CLK outputs when low. Internal pull-up
resistor.
External Components
Crystal Load Capacitors
The ICS252 requires a minimum number of external
components for proper operation.
Series Termination Resistor
Clock output traces over one inch should use series
termination. To series terminate a 50Ω trace (a
commonly used trace impedance), place a 33Ω resistor
in series with the clock line, as close to the clock output
pin as possible. The nominal impedance of the clock
output is 20Ω.
Decoupling Capacitor
As with any high-performance mixed-signal IC, the
ICS252 must be isolated from system power supply
noise to perform optimally.
A decoupling capacitor of 0.01µF must be connected
between VDD and the PCB ground plane.
The value (in pF) of these crystal caps should equal
(CL -6 pF)*2. In this equation, CL= crystal load
capacitance in pF. Example: For a crystal with a 16 pF
load capacitance, each crystal capacitor would be 20
pF [(16-6) x 2] = 20.
2
MDS 252 B
Integrated Circuit Systems, Inc.
The device crystal connections should include pads for
small capacitors from X1 to ground and from X2 to
ground. These capacitors are used to adjust the stray
capacitance of the board to match the nominally
required crystal load capacitance. Because load
capacitance can only be increased in this trimming
process, it is important to keep stray capacitance to a
minimum by using very short PCB traces (and no vias)
been the crystal and device. Crystal capacitors must be
connected from each of the pins X1 and X2 to ground.
●
525 Race Street, San Jose, CA 95126
Revision 011606
●
tel (408) 297-1201
●
www.icst.com
ICS252
Field Programmable Dual Output SS VersaClock Synthesizer
PCB Layout Recommendations
Output Drive Control
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed.
The ICS252 has two output drive settings. Low drive
should be selected when outputs are less than 100
MHz. High drive should be selected when outputs are
greater than 100 MHz. (Consult the AC Electrical
Characteristics for output rise and fall times for each
drive option.)
1) The 0.01µF decoupling capacitor should be mounted
on the component side of the board as close to the
VDD pin as possible. No vias should be used between
the decoupling capacitor and VDD pin. The PCB trace
to VDD pin should be kept as short as possible, as
should the PCB trace to the ground via. Distance of the
ferrite bead and bulk decoupling from the device is less
critical.
2) The external crystal should be mounted just next to
the device with short traces. The X1 and X2 traces
should not be routed next to each other with minimum
spaces, instead they should be separated and away
from other traces.
3) To minimize EMI, the 33Ω series termination resistor
(if needed) should be placed close to the clock output.
4) An optimum layout is one with all components on the
same side of the board, minimizing vias through other
signal layers. Other signal traces should be routed
away from the ICS252. This includes signal traces just
underneath the device, or on layers adjacent to the
ground plane layer used by the device.
ICS252 Configuration Capabilities
The architecture of the ICS252 allows the user to easily
configure the device to a wide range of output
frequencies, for a given input reference frequency.
The frequency multiplier PLL provides a high degree of
precision. The M/N values (the multiplier/divide values
available to generate the target VCO frequency) can be
set within the range of M = 1 to 2048 and N = 1 to 1024.
The ICS252 also provides separate output divide
values, from 2 through 20, to allow the two output clock
banks to support widely differing frequency values from
the same PLL.
Each output frequency can be represented
as:
OutputFreq
=
REFFreq
-------------------------------------OutputDivide
----⋅M
N
ICS VersaClock Software
ICS applies years of PLL optimization experience into a
user friendly software that accepts the user’s target
reference clock and output frequencies and generates
the lowest jitter, lowest power configuration, with only a
press of a button. The user does not need to have prior
PLL experience or determine the optimal VCO
frequency to support multiple output frequencies.
VersaClock software quickly evaluates accessible VCO
frequencies with available output divide values and
provides an easy to understand, bar code rating for the
target output frequencies. The user may evaluate
output accuracy, performance trade-off scenarios in
seconds.
Spread Spectrum Modulation
The ICS252 utilizes frequency modulation (FM) to
distribute energy over a range of frequencies. By
modulating the output clock frequencies, the device
effectively lowers energy across a broader range of
frequencies; thus, lowering a system’s
electro-magnetic interference (EMI). The modulation
rate is the time from transitioning from a minimum
frequency to a maximum frequency and then back to
the minimum.
Spread Spectrum Modulation can be applied as either
“center spread” or “down spread”. During center spread
modulation, the deviation from the target frequency is
equal in the positive and negative directions. The
effective average frequency is equal to the target
frequency. In applications where the clock is driving a
component with a maximum frequency rating, down
spread should be applied. In this case, the maximum
frequency, including modulation, is the target
frequency. The effective average frequency is less than
the target frequency.
The ICS252 operates in both center spread and down
spread modes. For center spread, the frequency can
be modulated between +/- 0.125% to +/-2.0%. For
3
MDS 252 B
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
Revision 011606
●
tel (408) 297-1201
●
www.icst.com
ICS252
Field Programmable Dual Output SS VersaClock Synthesizer
down spread, the frequency can be modulated
between -0.25% to -4.0%.
Both output frequency banks will utilize identical spread
spectrum percentage deviations and modulation rates,
if a common VCO frequency can be identified.
rates. For applications requiring the driving of
“down-circuit” PLLs, Zero Delay Buffers, or those
adhering to PCI standards, the spread spectrum
modulation rate should be set to 30-33 kHz. For other
applications, a 120 kHz modulation option is available.
Spread Spectrum Modulation Rate
The spread spectrum modulation frequency applied to
the output clock frequency may occur at a variety of
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the ICS252. These ratings, which
are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of the
device at these or any other conditions above those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can
affect product reliability. Electrical parameters are guaranteed only over the recommended operating
temperature range.
Parameter
Condition
Min.
Supply Voltage, VDD
Referenced to GND
Inputs
Clock Outputs
Max.
Units
-0.5
7
V
Referenced to GND
-0.5
VDD+ 0.5
V
Referenced to GND
-0.5
VDD+ 0.5
V
-65
150
°C
260
°C
125
°C
Storage Temperature
Soldering Temperature
Typ.
Max 10 seconds
Junction Temperature
Recommended Operation Conditions
Parameter
Min.
Typ.
Max.
Units
Ambient Operating Temperature (ICS252M)
0
+70
°C
Ambient Operating Temperature (ICS252MI)
-40
+85
°C
+3.465
V
4
ms
Power Supply Voltage (measured in respect to GND)
+3.135
+3.3
Power Supply Ramp Time
4
MDS 252 B
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
Revision 011606
●
tel (408) 297-1201
●
www.icst.com
ICS252
Field Programmable Dual Output SS VersaClock Synthesizer
DC Electrical Characteristics
Unless stated otherwise, VDD = 3.3V ±5%, Ambient Temperature -40 to +85°C
Parameter
Symbol
Operating Voltage
Conditions
VDD
Min.
Typ.
Max.
Units
3.135
3.3
3.465
V
Configuration Dependent
- See VersaClockTM
Operating Supply Current
Input High Voltage
IDD
mA
Two 33.3333 MHz output,
PDTS = 1, no load
Note 1
16
mA
500
µA
V
Input High Voltage
VIH
PDTS = 0
SEL
Input Low Voltage
VIL
SEL
Input High Voltage, PDTS
VIH
Input Low Voltage, PDTS
VIL
Input High Voltage
VIH
ICLK
Input Low Voltage
VIL
ICLK
Output High Voltage
(CMOS High)
VOH
IOH = -4 mA
VDD-0.4
V
Output High Voltage
VOH
IOH = -8 mA (Low Drive);
IOH = -12 mA (High Drive)
2.4
VDD-0.4
V
Output Low Voltage
VOL
IOL = 8 mA (Low Drive);
IOL = 12 mA (High Drive)
Short Circuit Current
IOS
±70
mA
Nominal Output
Impedance
ZO
20
Ω
VDD/2+1
0.4
VDD-0.5
V
V
0.4
VDD/2+1
V
V
VDD/2-1
0.4
V
V
Internal Pull-up Resistor
RPUP
SEL, PDTS
190
kΩ
Internal Pull-down
Resistor
RPD
Clock outputs CLK1 and
CLK2
120
kΩ
Input Capacitance
CIN
inputs
4
pF
Note 1: Example with 25 MHz crystal input with output of 33.3 MHz, no load, and VDD = 3.3 V.
5
MDS 252 B
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
Revision 011606
●
tel (408) 297-1201
●
www.icst.com
ICS252
Field Programmable Dual Output SS VersaClock Synthesizer
AC Electrical Characteristics
Unless stated otherwise, VDD = 3.3V ±5%, Ambient Temperature -40 to +85° C
Parameter
Symbol
Input Frequency
FIN
Conditions
Min.
Typ.
Max. Units
Fundamental Crystal
5
27
MHz
Input Clock
2
150
MHz
0.314
200
MHz
Output Frequency
Output Rise Time
tOR
20% to 80%, Note 1
1
ns
Output Fall Time
tOF
80% to 20%, Note 1
1
ns
Duty Cycle
Note 2
Power-up Time
One Sigma Clock Period Jitter
Maximum Absolute Jitter
tja
40
49-51
60
%
PLL lock time from
power-up
4
10
ms
PDTS goes high until
stable CLK output,
Spread Spectrum Off
.6
2
ms
PDTS goes high until
stable CLK output,
Spread Spectrum On
4
7
ms
Configuration Dependent
50
ps
Deviation from Mean.
Configuration Dependent
+200
ps
Note 1: Measured with 15 pF load.
Note 2: Duty Cycle is configuration dependent. Most configurations are minimum 45% and maximum 55%.
Thermal Characteristics
Parameter
Symbol
Conditions
Min.
Typ.
Max. Units
Thermal Resistance Junction to
Ambient
θJA
Still air
150
°C/W
θJA
1 m/s air flow
140
°C/W
θJA
3 m/s air flow
120
°C/W
Thermal Resistance Junction to Case
θJC
40
°C/W
6
MDS 252 B
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
Revision 011606
●
tel (408) 297-1201
●
www.icst.com
ICS252
Field Programmable Dual Output SS VersaClock Synthesizer
Marking Diagram
Marking Diagram (Pb free)
8
8
5
252PML
######
YYWW
252PM
######
YYWW
1
4
8
5
1
4
8
5
252PMIL
######
YYWW
252PMI
######
YYWW
1
5
1
4
4
Notes:
1. ###### is the lot number.
2. YYWW is the last two digits of the year and week that the part was assembled.
3. “I” denotes industrial temp. range (if applicable).
4. “L” denotes Pb (lead) free package.
5. Bottom marking: country of origin.
7
MDS 252 B
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
Revision 011606
●
tel (408) 297-1201
●
www.icst.com
ICS252
Field Programmable Dual Output SS VersaClock Synthesizer
Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Body)
Package dimensions are kept current with JEDEC Publication No. 95
Millimeters
8
Symbol
E
Min
A
A1
B
C
D
E
e
H
h
L
α
H
INDEX
AREA
1 2
D
A
Inches
Max
Min
1.35
1.75
0.10
0.25
0.33
0.51
0.19
0.25
4.80
5.00
3.80
4.00
1.27 BASIC
5.80
6.20
0.25
0.50
0.40
1.27
0°
8°
Max
.0532
.0688
.0040
.0098
.013
.020
.0075
.0098
.1890
.1968
.1497
.1574
0.050 BASIC
.2284
.2440
.010
.020
.016
.050
0°
8°
h x 45
A1
C
-Ce
SEATING
PLANE
B
L
.10 (.004)
C
Ordering Information
Part / Order Number
ICS252MP
ICS252MIP
ICS252MPLF
ICS252MIPLF
Marking
Shipping Packaging
Package
Temperature
Tubes
Tubes
Tubes
Tubes
8-pin SOIC
8-pin SOIC
8-pin SOIC
8-pin SOIC
0 to +70° C
-40 to +85° C
0 to +70° C
-40 to +85° C
See Page 7 Above
“LF” denotes Pb (lead) free package.
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS)
assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would
result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial
applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary
environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any
circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or
critical medical instruments.
8
MDS 252 B
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
Revision 011606
●
tel (408) 297-1201
●
www.icst.com
ICS252
Field Programmable Dual Output SS VersaClock Synthesizer
Revision History
Rev.
Originator
Date
Description of Change
A
R.Willner
04/08/05
Preliminary release.
B
R.Willner
01/16/06
Corrected Block Diagram. Released from Prelim to Final.
9
MDS 252 B
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
Revision 011606
●
tel (408) 297-1201
●
www.icst.com
Similar pages