19-6393; Rev 0; 7/12 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer General Description Features The MAX5395 single, 256-tap volatile, low-voltage linear taper digital potentiometer offers three end-toend resistance values of 10kΩ, 50kΩ, and 100kΩ. Potentiometer terminals are independent of supply for voltages up to 5.25V with single-supply operation from 1.7V to 5.5V (charge pump enabled). User-controlled shutdown modes allow the H, W, or L terminal to be opened with the wiper position set to zero-code, midcode, full-code, or the value contained in the wiper register. Ultra-low-quiescent supply current (< 1µA) can be achieved for supply voltages between 2.6V and 5.5V by disabling the internal charge pump and not allowing potentiometer terminals to exceed the supply voltage by more than 0.3V. The MAX5395 provides a low 50ppm/°C end-to-end temperature coefficient and features an I2C serial interface. S Single Linear Taper 256-Tap Positions S 10kI, 50kI, and 100kI End-to-End Resistance S 1.7V to 5.5V Extended Single Supply S 0 to 5.25V H, W, L Operating Voltage Independent of VDD S 1µA (typ) Supply Current in Low-Power Mode S ±1.0 LSB INL, ±0.5 LSB DNL (max) Wiper Accuracy S Power-On Sets Wiper to Midscale S 50ppm/NC End-to-End Temperature Coefficient S 5ppm/NC Ratiometric Temperature Coefficient S -40NC to +125NC Operating Temperature Range S 2mm x 2mm, 8-Pin TDFN Package S I2C-Compatible Serial Interface The small package size, low operating supply voltage, low supply current, and automotive temperature range of the MAX5395 make the device uniquely suited for the portable consumer market, battery-backup industrial applications, and automotive market. Applications Portable Electronics System Calibration The MAX5395 is available in a lead-free, 8-pin TDFN (2mm x 2mm) package. The device operates over the -40°C to +125°C automotive temperature range. Battery-Powered Systems Automotive Electronics Mechanical Potentiometer Replacement Ordering Information appears at end of data sheet. Typical Operating Circuit VDD 1.7V TO 5.5V (CHARGE PUMP ENABLED) H +5V VS MAX5395 MAX4250 ADDR0 I2C INTERFACE SDA SCL GND VO W L R1 VO / VS = 1 + RMAX5395/R1 For related parts and recommended products to use with this part, refer to: www.maxim-ic.com/MAX5395.related For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer ABSOLUTE MAXIMUM RATINGS (All voltages referenced to GND.) VDD ..........................................................................-0.3V to +6V H, W, L (charge pump enabled) ..........................-0.3V to +5.5V H, W, L (charge pump disabled)................. -0.3V to the lower of (VDD + 0.3V) or +6V ADDR0.......................................................... -0.3V to the lower of (VDD + 0.3V) or +6V All Other Pins ..........................................................-0.3V to +6V Continuous Power Dissipation (TA = +70NC) TDFN (derate 11.9mW/NC above +70NC)..................953.5mW Operating Temperature Range ........................ -40NC to +125NC Storage Temperature Range............................ -65NC to + 150NC Junction Temperature......................................................+150NC Lead Temperature (soldering, 10s)............................... + 300NC Soldering Temperature (reflow) ......................................+260NC Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. PACKAGE THERMAL CHARACTERISTICS (Note 1) TDFN Junction-to-Ambient Thermal Resistance (qJA)........83.9°C/W Junction-to-Case Thermal Resistance (qJC).............37.0°C/W Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a fourlayer board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial. ELECTRICAL CHARACTERISTICS (VDD = 1.7V to 5.5V, VH = VDD, VL = GND, TA = -40°C to +125°C, unless otherwise noted. Typical values are at VDD = 1.8V, TA = +25°C.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS RESOLUTION 256-Tap Family N 256 Tap DC PERFORMANCE (Voltage-Divider Mode) Integral Nonlinearity (Note 3) INL Differential Nonlinearity DNL (Note 3) Ratiometric Resistor Tempco (DVW/VW)/DT, VH = VDD, VL = GND, No Load Full-Scale Error (Code FFh) Charge pump enabled, 1.7V < VDD < 5.5V MAX5395M Charge pump disabled, 2.6V MAX5395N < VDD < 5.5V MAX5395L -1.0 +1.0 LSB -0.5 +0.5 LSB 5 -0.5 -0.5 LSB -1.0 Charge pump enabled, 1.7V < VDD < 5.5V MAX5395M Charge pump disabled, 2.6V MAX5395N < VDD < 5.5V MAX5395L Zero-Scale Error (Code 00h) ppm/°C +0.5 +0.5 LSB +1.0 DC PERFORMANCE (Variable Resistor Mode) Integral Nonlinearity (Note 4) Differential Nonlinearity Wiper Resistance (Note 5) R-INL R-DNL RWL Charge pump enabled, 1.7V < VDD < 5.5V MAX5395M Charge pump disabled, 2.6V MAX5395N < VDD < 5.5V MAX5395L -1.0 +1.0 -1.0 +1.0 -1.5 +1.5 (Note 4) -0.5 Charge pump enabled, 1.7V < VDD < 5.5V Charge pump disabled, 2.6V < VDD < 5.5V +0.5 25 50 200 LSB LSB W 2 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer ELECTRICAL CHARACTERISTICS (continued) (VDD = 1.7V to 5.5V, VH = VDD, VL = GND, TA = -40°C to +125°C, unless otherwise noted. Typical values are at VDD = 1.8V, TA = +25°C.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DC PERFORMANCE (Resistor Characteristics) Terminal Capacitance CH, CL Measured to GND 10 Wiper Capacitance CW Measured to GND 20 pF End-to-End Resistor Tempco TCR No load 50 ppm/°C End-to-End Resistor Tolerance Wiper not connected -25 pF +25 % AC PERFORMANCE -3dB Bandwidth Total Harmonic Distortion Plus Noise Wiper Settling Time Charge-Pump Feedthrough at W BW Code = 80h, 10pF load, VDD = 1.8V THD+N (Note 6) tS (Note 7) 10kW 1600 50kW 340 100kW 165 kHz 0.035 10kW 190 50kW 400 100kW 664 VRW % ns 600 nVRMS POWER SUPPLIES Supply Voltage Range VDD Terminal Voltage Range (H, W, L to GND) Supply Current (Note 8) IVDD 1.7 5.5 Charge pump enabled, 1.7V < VDD < 5.5V 0 5.25 Charge pump disabled, 2.6V < VDD < 5.5V Charge pump disabled, 2.6V < VDD < 5.5V 0 VDD Charge pump enabled, 1.7V < VDD < 5.5V V V 1 VDD = 5.5V 25 VDD = 1.7V 20 µA DIGITAL INPUTS Minimum Input High Voltage VIH 2.6V < VDD < 5.5V 1.7V < VDD < 2.6V Maximum Input Low Voltage VIL 2.6V < VDD < 5.5V 1.7V < VDD < 2.6V Input Leakage Current 70 30 -1 Input Capacitance ADDR0 Pullup/Pulldown Strength %x VDD 80 RPURRPD (Note 9) 20 %x VDD +1 µA 5 pF 60 kW TIMING CHARACTERISTICS (Note 10) Maximum SCL Frequency Setup Time for START Condition fSCL tSU:STA 400 0.6 kHz µs 3 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer ELECTRICAL CHARACTERISTICS (continued) (VDD = 1.7V to 5.5V, VH = VDD, VL = GND, TA = -40°C to +125°C, unless otherwise noted. Typical values are at VDD = 1.8V, TA = +25°C.) (Note 2) PARAMETER Hold Time for START Condition SCL High Time SCL Low Time SYMBOL CONDITIONS MIN TYP MAX UNITS tHD:STA 0.6 µs tHIGH 0.6 µs tLOW 1.3 µs Data Setup Time tSU:DAT 100 ns Data Hold Time tHD:DAT 0 µs SDA, SCL Rise Time tR 0.3 µs SDA, SCL Fall Time tF 0.3 µs Setup Time for STOP Conditions tSU:STO 0.6 µs Bus Free Time Between STOP and START Conditions tBUF 1.3 µs Pulse-Suppressed Spike Width tSP 50 ns Capacitive Load for Each Bus CB 400 pF Note 2: All devices are production tested at TA = +25°C and are guaranteed by design and characterization for TA = -40°C to +125°C. Note 3: DNL and INL are measured with the potentiometer configured as a voltage-divider with VH = 5.25V (QP enabled) or VDD (QP disabled) and VL = GND. The wiper terminal is unloaded and measured with an ideal voltmeter. Note 4: R-DNL and R-INL are measured with the potentiometer configured as a variable resistor (Figure 1). H is unconnected and L = GND. For charge pump enabled, VDD = 1.7V to 5.5V, the wiper terminal is driven with a source current of 400µA for the 10kΩ configuration, 80µA for the 50kΩ configuration, and 40µA for the 100kΩ configuration. For charge pump disabled and VDD = 5.5V, the wiper terminal is driven with a source current of 400µA for the 10kΩ configuration, 80µA for the 50kΩ configuration, and 40µA for the 100kΩ configuration. For charge pump disabled and VDD = 2.6V, the wiper terminal is driven with a source current of 200µA for the 10kΩ configuration, 40µA for the 50kΩ configuration, and 20µA for the 100kΩ configuration. Note 5: The wiper resistance is the maximum value measured by injecting the currents given in Note 4 into W with L = GND. RW = (VW - VH)/IW. Note 6: Measured at W with H driven with a 1kHz, 0V to VDD amplitude tone and VL = GND. Wiper at midscale with a 10pF load. Note 7: Wiper-settling time is the worst-case 0-to-50% rise time, measured between tap 0 and tap 127. H = VDD, L = GND, and the wiper terminal is loaded with 10pF capacitance to ground. Note 8: Digital Inputs at VDD or GND. Note 9: An unconnected condition on the ADDR0 pin is sensed via a pullup and pulldown operation. For proper operation, the ADDR0 pin should be tied to VDD, GND, or left unconnected with minimal capacitance. Note 10:Digital timing is guaranteed by design and characterization, and is not production tested. H N.C. W L W L Figure 1. Voltage-Divider and Variable Resistor Configurations 4 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer Typical Operating Characteristics SUPPLY CURRENT vs. DIGITAL INPUT VOLTAGE 25 20 15 10 5 0 25 20 15 5 1 2 3 4 0 5 1.70 3.60 4.55 5.50 RESISTANCE (W-TO-L) vs. TAP POSITION (50kI) RESISTANCE (W-TO-L) vs. TAP POSITION (100kI) 5 4 3 100 40 90 W-TO-L RESISTANCE (kI) W-TO-L RESISTANCE (kI) 45 35 30 25 20 15 80 70 60 50 40 30 2 10 20 1 5 10 0 0 64 96 128 160 192 224 256 MAX5395 toc06 50 MAX5395 toc04 6 0 0 32 64 96 128 160 192 224 256 0 32 64 96 128 160 192 224 256 TAP POSITION WIPER RESISTANCE vs. WIPER VOLTAGE WIPER RESISTANCE vs. WIPER VOLTAGE END-TO-END RESISTANCE PERCENTAGE CHANGE vs. TEMPERATURE WIPER RESISTANCE (I) VDD = 5V, QP OFF 35 VDD = 1.8V, QP ON 30 25 20 15 10 5 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 WIPER VOLTAGE (V) 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 WIPER VOLTAGE (V) 0.8 MAX5395 toc08 MAX5395 toc07a 40 END-TO-END RESISTANCE PERCENTAGE CHANGE (%) TAP POSITION MAX5395 toc07b TAP POSITION VDD = 2.6V, QP OFF 0 2.65 RESISTANCE (W-TO-L) vs. TAP POSITION (10kI) 7 75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 0 TA = -40°C 10 INPUT VOLTAGE (V) 8 32 TA = +25°C 30 DIGITAL INPUT VOLTAGE (V) 9 0 TA = +125°C TEMPERATURE (°C) 10 W-TO-L RESISTANCE (kI) VDD = 3.3V (HIGH-LOW) VDD = 1.8V (LOW-HIGH) 0 -40 -25 -10 5 20 35 50 65 80 95 110 125 WIPER RESISTANCE (I) VDD = 5V (HIGH-LOW) VDD = 1.8V (HIGH-LOW) 35 SUPPLY CURRENT (µA) SUPPLY CURRENT (µA) SUPPLY CURRENT (µA) 30 VDD = 5V (LOW-HIGH) VDD = 3.3V (LOW-HIGH) SUPPLY CURRENT vs. INPUT VOLTAGE 40 MAX5395 toc02 VDD = 1.8V 35 2600 2400 2200 2000 1800 1600 1400 1200 1000 800 600 400 200 0 MAX5395 toc05 40 MAX5395 toc01 SUPPLY CURRENT vs. TEMPERATURE MAX5395 toc03 (VDD = 1.8V, TA = +25NC, unless otherwise noted.) 0.6 100kI 0.4 0.2 50kI 0 10kI -0.2 -40 -25 -10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) 5 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer Typical Operating Characteristics (continued) (VDD = 1.8V, TA = +25NC, unless otherwise noted.) TAP-TO-TAP SWITCHING TRANSIENT (CODE 127 TO 128, 10kΩ) TAP-TO-TAP SWITCHING TRANSIENT (CODE 127 TO 128, 50kΩ) MAX5395 toc09 MAX5395 toc10 MAX5395 toc11 VW-L 10mV/div VW-L 10mV/div VW-L 10mV/div VSCL 2V/div VSCL 2V/div VSCL 2V/div 200ns/div 200ns/div POWER-ON TRANSIENT (10kΩ) 200ns/div POWER-ON TRANSIENT (50kΩ) MAX5395 toc12a POWER-ON TRANSIENT (100kΩ) MAX5395 toc12b MAX5395 toc12c VW-L 1V/div VW-L 1V/div VW-L 1V/div VDD 1V/div VDD 1V/div VDD 1V/div 10µs/div 10µs/div 10µs/div MIDSCALE FREQUENCY RESPONSE (10kI) MIDSCALE FREQUENCY RESPONSE (50kI) MIDSCALE FREQUENCY RESPONSE (100kI) -10 MAX5395 toc15 0 VDD = 5V -10 GAIN (dB) 0 GAIN (dB) 0 10 MAX5395 toc14 10 MAX5395 toc13 10 GAIN (dB) TAP-TO-TAP SWITCHING TRANSIENT (CODE 127 TO 128, 100kΩ) VDD = 5V -10 VDD = 5V -20 -20 VDD = 1.8V VIN = 1VP-P CW = 10pF -30 0.01k 0.1k -20 VIN = 1VP-P CW = 10pF 1k 10k 100k FREQUENCY (Hz) 1M 10M -30 0.01k 0.1k VIN = 1VP-P CW = 10pF VDD = 1.8V 1k 10k 100k FREQUENCY (Hz) 1M 10M -30 0.01k 0.1k VDD = 1.8V 1k 10k 100k 1M 10M FREQUENCY (Hz) 6 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer Typical Operating Characteristics (continued) (VDD = 1.8V, TA = +25NC, unless otherwise noted.) TOTAL HARMONIC DISTORTION PLUS NOISE vs. FREQUENCY 0.18 900 800 VOLTAGE (nVRMS) 0.16 0.12 0.10 10kI 50kI 0.06 50kI 100kI 700 600 10kI 500 400 300 200 0.04 100 100kI 0 0.01 0.1 1 0 10 0.50 100 0.75 1.00 FREQUENCY (kHz) VDD = 1.8V, VH = 5.0V, CHARGE PUMP ON VDD = 2.6V, VH = 2.6V, CHARGE PUMP OFF VDD = 5.0V, VH = 5.0V, CHARGE PUMP OFF 0.4 0.3 0.3 DNL (LSB) 0.1 DNL (LSB) 0.2 0.1 0 -0.1 0 -0.1 -0.2 -0.2 -0.2 -0.3 -0.3 -0.3 -0.4 -0.4 -0.4 -0.5 -0.5 64 96 0.2 96 64 96 128 160 192 224 256 VARIABLE-RESISTOR INL vs. TAP POSITION (10kI) VARIABLE-RESISTOR INL vs. TAP POSITION (50kI) VARIABLE-RESISTOR INL vs. TAP POSITION (100kI) 0.5 0.4 0.3 INL (LSB) 0.1 0 -0.1 -0.2 -0.2 -0.3 -0.3 VDD = 1.8V, VH = 5.0V, CHARGE PUMP ON VDD = 5.0V, VH = 5.0V, CHARGE PUMP OFF -0.5 96 128 160 192 224 256 TAP POSITION VDD = 1.8V, VH = 5.0V, CHARGE PUMP ON VDD = 2.6V, VH = 2.6V, CHARGE PUMP OFF VDD = 5.0V, VH = 5.0V, CHARGE PUMP OFF 0.4 0.3 0.2 0.1 0 -0.1 -0.2 VDD = 1.8V, VH = 5.0V, CHARGE PUMP ON VDD = 5.0V, VH = 5.0V, CHARGE PUMP OFF -0.4 -0.5 64 0.5 VDD = 2.6V, VH = 2.6V, CHARGE PUMP OFF 0.2 -0.1 32 32 TAP POSITION 0 0 0 128 160 192 224 256 TAP POSITION 0.1 -0.4 64 INL (LSB) 0.3 32 TAP POSITION VDD = 2.6V, VH = 2.6V, CHARGE PUMP OFF 0.4 -0.5 0 128 160 192 224 256 MAX5395 toc19b 0.5 32 VDD = 1.8V, VH = 5.0V, CHARGE PUMP ON VDD = 2.6V, VH = 2.6V, CHARGE PUMP OFF VDD = 5.0V, VH = 5.0V, CHARGE PUMP OFF 0.4 0.1 -0.1 2.00 0.5 0.2 0 1.75 VARIABLE-RESISTOR DNL vs. TAP POSITION (100kI) 0.2 0 INL (LSB) VDD = 1.8V, VH = 5.0V, CHARGE PUMP ON VDD = 2.6V, VH = 2.6V, CHARGE PUMP OFF VDD = 5.0V, VH = 5.0V, CHARGE PUMP OFF 0.4 MAX5395 toc19a DNL (LSB) 0.3 0.5 MAX5395 toc18a 0.5 1.50 VARIABLE-RESISTOR DNL vs. TAP POSITION (50kI) MAX5395 toc18b VARIABLE-RESISTOR DNL vs. TAP POSITION (10kI) 1.25 FREQUENCY (MHz) MAX5395 toc18c 0.02 MAX5395 toc19c THD+N (%) 0.14 0.08 MAX5395 toc17 MAX5395 toc16 0.20 CHARGE-PUMP FEEDTHROUGH AT W 1000 -0.3 -0.4 -0.5 0 32 64 96 128 160 192 224 256 TAP POSITION 0 32 64 96 128 160 192 224 256 TAP POSITION 7 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer Typical Operating Characteristics (continued) (VDD = 1.8V, TA = +25NC, unless otherwise noted.) 0.3 0.1 0.1 -0.1 DNL (LSB) 0.2 0.1 DNL (LSB) 0.2 0 0 -0.1 0 -0.1 -0.2 -0.2 -0.2 -0.3 -0.3 -0.3 -0.4 -0.4 -0.4 -0.5 -0.5 64 96 64 96 0 128 160 192 224 256 96 128 160 192 224 256 VOLTAGE-DIVIDER INL vs. TAP POSITION (10kI) VOLTAGE-DIVIDER INL vs. TAP POSITION (50kI) VOLTAGE-DIVIDER INL vs. TAP POSITION (100kI) 0.5 VDD = 1.8V, VH = 5.0V, CHARGE PUMP ON VDD = 2.6V, VH = 2.6V, CHARGE PUMP OFF VDD = 5.0V, VH = 5.0V, CHARGE PUMP OFF 0.4 0.3 0.5 0.3 0.1 -0.1 INL (LSB) 0.1 INL (LSB) 0.2 0.1 0 0 -0.1 0 -0.1 -0.2 -0.2 -0.2 -0.3 -0.3 -0.3 -0.4 -0.4 -0.4 -0.5 -0.5 64 96 128 160 192 224 256 TAP POSITION VDD = 1.8V, VH = 5.0V, CHARGE PUMP ON VDD = 2.6V, VH = 2.6V, CHARGE PUMP OFF VDD = 5.0V, VH = 5.0V, CHARGE PUMP OFF 0.4 0.2 32 64 TAP POSITION 0.2 0 32 TAP POSITION VDD = 1.8V, VH = 5.0V, CHARGE PUMP ON VDD = 2.6V, VH = 2.6V, CHARGE PUMP OFF VDD = 5.0V, VH = 5.0V, CHARGE PUMP OFF 0.3 32 TAP POSITION 0.5 0.4 -0.5 0 128 160 192 224 256 MAX5395 toc21b 32 VDD = 1.8V, VH = 5.0V, CHARGE PUMP ON VDD = 2.6V, VH = 2.6V, CHARGE PUMP OFF VDD = 5.0V, VH = 5.0V, CHARGE PUMP OFF 0.4 MAX5395 toc20c 0.3 0.5 0.2 0 INL (LSB) VDD = 1.8V, VH = 5.0V, CHARGE PUMP ON VDD = 2.6V, VH = 2.6V, CHARGE PUMP OFF VDD = 5.0V, VH = 5.0V, CHARGE PUMP OFF 0.4 MAX5395 toc21a DNL (LSB) 0.3 0.5 VOLTAGE-DIVIDER DNL vs. TAP POSITION (100kI) MAX5395 toc21c VDD = 1.8V, VH = 5.0V, CHARGE PUMP ON VDD = 2.6V, VH = 2.6V, CHARGE PUMP OFF VDD = 5.0V, VH = 5.0V, CHARGE PUMP OFF 0.4 MAX5395 toc20a 0.5 VOLTAGE-DIVIDER DNL vs. TAP POSITION (50kI) MAX5395 toc20b VOLTAGE-DIVIDER DNL vs. TAP POSITION (10kI) -0.5 0 32 64 96 128 160 192 224 256 TAP POSITION 0 32 64 96 128 160 192 224 256 TAP POSITION 8 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer Pin Configuration TOP VIEW GND 2 + L 1 8 H 7 W MAX5395 ADDR0 3 6 VDD EP SDA 4 5 SCL TDFN Pin Description PIN NAME FUNCTION 1 L 2 GND 3 ADDR0 4 SDA Address Input 0. Connected to VDD, GND, or open. I2C Serial Data Input 5 SCL I2C Clock Input 6 VDD Power Supply 7 W Wiper Terminal 8 H High Terminal. The voltage at H can be greater than or less than the voltage at L. Current can flow into or out of H. — EP Exposed Pad. Internally connected to GND. Connect to ground. Low Terminal. The voltage at L can be greater than or less than the voltage at H. Current can flow into or out of L. Ground 9 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer Functional Diagram MAX5395 H L Characteristics. The charge pump is on by default but can be disabled with QP_OFF and enabled with the QP_ON commands (Table 1). The MAX5395 minimum supply voltage with charge pump disabled is limited to 2.6V and terminal voltage cannot exceed -0.3V to (VDD + 0.3V). I2C Interface W GND VDD ADDRO SDA I2C INTERFACE SCL Detailed Description The MAX5395 single, 256-tap volatile, low-voltage linear taper digital potentiometer offers three end-toend resistance values of 10kΩ, 50kΩ, and 100kΩ. Potentiometer terminals are independent of supply for voltages up to +5.25V with single-supply operation from 1.7V to 5.5V (charge pump enabled). User-controlled shutdown modes allow the H, W, or L terminals to be opened with the wiper position set to zero-code, midcode, full-code, or the value contained in the wiper register. Ultra-low-quiescent supply current (< 1µA) can be achieved for supply voltages between 2.6V and 5.5V by disabling the internal charge pump and not allowing potentiometer terminals to exceed the supply voltage by more than 0.3V. The MAX5395 provides a low 50ppm/°C end-to-end temperature coefficient and features a I2C serial interface. The small package size, low supply operating voltage, low supply current, and automotive temperature range of the MAX5395 make the device uniquely suited for the portable consumer market, battery-backup industrial applications, and automotive market. Charge Pump The MAX5395 contains an internal charge pump that guarantees the maximum wiper resistance, RWL, to be less than 50Ω (25Ω typ) for supply voltages down to 1.7V and allows pins H, W, and L to be driven between GND and 5.25V independent of VDD. Minimal chargepump feedthrough is present at the terminal outputs and is illustrated by the Charge-Pump Feedthrough at W vs. Frequency graph in the Typical Operating The MAX5395 feature an I2C/SMBus-compatible, 2-wire serial interface consisting of a serial data line (SDA) and a serial clock line (SCL). SDA and SCL enable communication between the MAX5395 and the master at clock rates up to 400kHz. Figure 1 shows the 2-wire interface timing diagram. The master generates SCL and initiates data transfer on the bus. The master device writes data to the MAX5395 by transmitting the proper slave address followed by the command byte and then the data word. Each transmit sequence is framed by a START (S) or Repeated START (Sr) condition and a STOP (P) condition. Each word transmitted to the MAX5395 is 8 bits long and is followed by an acknowledge clock pulse. A master reading data from the MAX5395 must transmit the proper slave address followed by a series of nine SCL pulses for each byte of data requested. The MAX5395 transmit data on SDA in sync with the master-generated SCL pulses. The master acknowledges receipt of each byte of data. Each read sequence is framed by a START or Repeated START condition, a not acknowledge, and a STOP condition. SDA operates as both an input and an open-drain output. A pullup resistor, typically 4.7kI, is required on SDA. SCL operates only as an input. A pullup resistor, typically 4.7kI, is required on SCL if there are multiple masters on the bus, or if the single master has an opendrain SCL output. Series resistors in line with SDA and SCL are optional. Series resistors protect the digital inputs of the MAX5395 from high voltage spikes on the bus lines and minimize crosstalk and undershoot of the bus signals. The MAX5395 can accommodate bus voltages higher than VDD up to a limit of +5.5V. Bus voltages lower than VDD are not recommended and may result in significantly increased interface currents and data corruption. The MAX5395 with I2C interface contains a shift register that decodes the command and address bytes, routing the data to the register. Data written to a memory register immediately updates the wiper position. The wiper powers up in mid position, D[7:0] = 0x80 with charge pump enabled. 10 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer I2C START and STOP Conditions SDA and SCL idle high when the bus is not in use. A master initiates communication by issuing a START condition. A START condition is a high-to-low transition on SDA with SCL high. A STOP condition is a low-to-high transition on SDA while SCL is high (Figure 2). A START condition from the master signals the beginning of a transmission to the MAX5395. The master terminates transmission and frees the bus, by issuing a STOP condition. The bus remains active if a Repeated START condition is generated instead of a STOP condition. I2C Early STOP and Repeated START Conditions The MAX5395 recognizes a STOP condition at any point during data transmission except if the STOP condition occurs in the same high pulse as a START condition. For proper operation, do not send a STOP condition during the same SCL high pulse as the START condition. Transmissions ending in an early STOP condition will not impact the internal device settings. If the STOP occurs during a readback byte, the transmission is terminated and a later read mode request will begin transfer of the requested register data from the beginning. See Figure 3. It is possible to interrupt a transmission to a MAX5395 with a new START (Repeated START) condition (perhaps addressing another device), which leaves the input registers with data that has not been transferred to the internal registers. The unused data will not be stored under these conditions. The aborted MAX5395 I2C sequence will have no effect on the part. I2C Acknowledge In write mode, the acknowledge bit (ACK) is a clocked 9th bit that the MAX5395 uses to handshake receipt of each byte of data as shown in Figure 4. The MAX5395 pulls down SDA during the entire master-generated 9th clock pulse if the previous byte is successfully received. Monitoring ACK allows for detection of unsuccessful data transfers. An unsuccessful data transfer occurs if a receiving device is busy or if a system fault has occurred. In the event of an unsuccessful data transfer, the bus master will retry communication. tHD:STA SDA tSU:STD tSU:DTA tSU:DAT tBUF tHD-DAT tLOW SCL tHIGH tHD:STA tR tF REPEATED START CONDITION (Sr) START CONDITION (S) ACKNOWLEDGE (A) STOP CONDITION START CONDITION (P) (S) Figure 2. I2C Timing Diagram S Sr P P S S P P S P SCL SDA VALID START, REPEATED START, AND STOP PULSES INVALID START/STOP PULSE PAIRINGS-ALL WILL BE RECOGNIZED AS STARTS Figure 3. I2C START(s), Repeated START(S), and STOP(S) Conditions 11 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer In read mode, the master pulls down SDA during the 9th clock cycle to acknowledge receipt of data from the MAX5395. An acknowledge is sent by the master after each read byte to allow data transfer to continue. A notacknowledge is sent when the master reads the final byte of data from the MAX5395, followed by a STOP condition. I2C Slave Address The slave address is defined as the seven most significant bits (MSBs) followed by the R/W bit. See Figure 5 and Figure 6. The five most significant bits are 01010 with the 3 LSBs determined ADDR0 as shown in Table 1. Setting the R/W bit to 1 configures the MAX5395 for read mode. Setting the R/W bit to 0 configures the MAX5395 for write mode. The slave address is the first byte of information sent to the MAX5395 after the START condition. The MAX5395 has the ability to detect an unconnected (N.C.) state on the ADDR0 input for additional address flexibility; if disconnecting the ADDR0 input, be certain to minimize all loading on the ADDR0 input (i.e. provide a landing for ADDR0, but do not allow any board traces). I2C Message Format for Writing A master device communicates with the MAX5395 by transmitting the proper slave address followed by command and data word. Each transmit sequence is framed Table 1. I2C Slave Address LSBs ADDR0 A1 A0 SLAVE ADDRESS GND 0 0 0101000 N.C. 0 1 0101001 VDD 1 1 0101011 N.C. = No connection. by a START or Repeated START condition and a STOP condition as described above. Each word is 8 bits long and is always followed by an acknowledge clock (ACK) pulse as shown in Figure 5. The first byte contains the address of the MAX5395 with R/W = 0 to indicate a write. The second byte contains the command to be executed and the third byte contains the data to be written. I2C Message Format for Readback Operations Each readback sequence is framed by a START or Repeated START condition and a STOP condition. Each word is 8 bits long and is followed by an acknowledge clock pulse as shown in Figure 6. The first byte contains the address of the MAX5395 with R/W = 0 to indicate a write. The second byte contains the register that is to be read back. There is a Repeated START condition, followed by the device address with R/W = 1 to indicate CLOCK PULSE FOR ACKNOWLEDGMENT START CONDITION SCL 1 2 9 NOT ACKNOWLEDGE SDA ACKNOWLEDGE Figure 4. I2C Acknowledge WRITE ADDRESS START BYTE #1: I2C SLAVE ADDRESS SDA 0 1 0 1 0 A1 A0 W A WRITE REGISTER BYTE #2: REG # = N WRITE DATA BYTE #3: DATA BYTE B[7:0] SEE REGISTER OPTIONS A D D D D D D D D A STOP SCL ACK. GENERATED BY MAX5395L/ MAX5395M/MAX5395N ACK. GENERATED BY I2C MASTER REG N UPDATED Figure 5. I2C Complete Write Serial Transmission 12 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer a read and an acknowledge clock. The master has control of the SCL line but the MAX5395 takes over the SDA line. The final byte in the frame contains the register data readback followed by a STOP condition. If additional bytes beyond those required to read back the requested data are provided, the MAX5395 will continue to read back ones. TSEL[1:0]: Tap select, 00- wiper is at contents of wiper register, 01 – wiper is at 0x00, 10 – wiper is at 0x80, 11 – wiper is at 0xFF. General Call Support The MAX5395 supports software reset through general call address 0x00 followed by R/W = 0, followed by 0x06 data. A software reset of the MAX5395 will return the part to the power-on default conditions. The MAX5395 will ACK the general call address and any command byte following, but will not support any general call features other than software reset. The wiper register and the configuration register are the only two registers that support readback (Table 2). Readback of all other registers is not supported and results in the readback of ones. D[7:0]: Wiper position QP: Charge pump status, 1 is enabled, 0 is disabled. HSW: H terminal switch status, 0 is closed, 1 is open WSW: W terminal switch status, 0 is closed, 1 is open LSW: L terminal switch status, 0 is closed, 1 is open Table 2. I2C READ Command Byte Summary REGISTER COMMAND BYTE DATA BYTE C7 C6 C5 C4 C3 C2 C1 C0 D7 D6 D5 D4 D3 D2 D1 D0 WIPER 0 0 0 0 0 0 0 0 D7 D6 D5 D4 D3 D2 D1 D0 CONFIG 1 0 0 0 0 0 0 0 QP 0 0 HSW LSW WSW WRITE ADDRESS START BYTE #1: I2C SLAVE ADDRESS SDA 0 1 0 1 0 A1 A0 W A WRITE COMMAND BYTE #2: COMMAND BYTE SEE REGISTER OPTIONS REPEATED READ ADDREESS START BYTE #3: I2C SLAVE ADDRESS A READ DATA BYTE #4: DATA BYTE B[7:0] TSEL[1:0] STOP 0 1 0 1 0 A1 A0 R A D D D D D D D D ~A SCL ACK. GENERATED BY MAX5395L/ MAX5395M/MAX5395N ACK. GENERATED BY I2C MASTER Figure 6. Standard I2C Register Read Sequence 13 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer Table 3. I2C Write Command Byte Summary COMMAND ADDRESS BYTE COMMAND BYTE A6 A5 A4 A3 A2 A1 A0 R/W DATA BYTE C7 C6 C5 C4 C3 C2 C1 C0 WIPER 0 0 0 0 0 0 0 0 0 SD_CLR 0 1 0 0 0 0 0 0 0 SD_H_WREG 0 1 0 0 1 0 0 0 0 SD_H_ZERO 0 1 0 0 1 0 0 0 1 SD_H_MID 0 1 0 0 1 0 0 1 0 SD_H_FULL 0 1 0 0 1 0 0 1 1 0 A 1 0 0 0 1 0 0 0 A SD_L_WREG S SD_L_ZERO See Table 1 0 1 0 0 0 1 0 0 1 SD_L_MID 0 1 0 0 0 1 0 1 0 SD_L_FULL 0 1 0 0 0 1 0 1 1 SD_W 0 1 0 0 0 0 1 X X QP_OFF 0 1 0 1 0 0 0 0 0 QP_ON 0 1 0 1 0 0 0 0 1 RST 0 1 1 0 0 0 0 0 0 WIPER Command The data byte writes to the wiper register and the potentiometer moves to the appropriate position. D[7:0] indicates the position of the wiper. D[7:0] = 0x00 moves the wiper to the position closest to L. D[7:0] = 0xFF moves the wiper closest to H. D[7:0] = 0x80 following power-on. SD_CLR Command Removes any existing shutdown condition. Connects all potentiometer terminals and returns the wiper to the value stored in the wiper register. The command does not affect the current status of the charge pump. SD_H_WREG Command Opens the H terminal and maintains the wiper at the wiper register location. Writes cannot be made to the wiper register while shutdown mode is engaged. Clearing shutdown mode will close the H terminal and allow the wiper register to be written. A RST will also deassert shutdown mode and return the wiper to midscale (0x80). This command does not affect the charge-pump status. SD_H_ZERO Command Moves wiper to zero-scale position (0x00) and opens the H terminal. The wiper register remains unaltered. Writes D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 A P Don’t Care cannot be made to the wiper register while shutdown mode is engaged. Clearing shutdown mode will return the wiper to the position contained in the wiper register and close the H terminal. A RST will also deassert shutdown mode and return the wiper to midscale (0x80). This command does not affect the charge-pump status. SD_H_MID Command Moves wiper to midscale position (0x80) and opens the H terminal. The wiper register remains unaltered. Writes cannot be made to the wiper register while shutdown mode is engaged. Clearing shutdown mode will return the wiper to the position contained in the wiper register and close the H terminal. A RST will also deassert shutdown mode and return the wiper to midscale (0x80). This command does not affect the charge-pump status. SD_H_FULL Command Moves wiper to full-scale position (0xFF) and opens the H terminal. The wiper register remains unaltered. Writes cannot be made to the wiper register while shutdown mode is engaged. Clearing shutdown mode will return the wiper to the position contained in the wiper register and close the H terminal. A RST will also deassert shutdown mode and return the wiper to midscale (0x80). This command does not affect the charge-pump status. 14 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer SD_L_WREG Command Opens the L terminal and maintains the wiper at the wiper register location. Writes cannot be made to the wiper register while shutdown mode is engaged. Clearing shutdown mode will close the L terminal and allow wiper register to be written. A RST will also deassert shutdown mode and return the wiper to midscale (0x80). This command does not affect the charge-pump status. SD_L_ZERO Command Moves wiper to zero-scale position (0x00) and opens the L terminal. The wiper register remains unaltered. Writes cannot be made to the wiper register while shutdown mode is engaged. Clearing shutdown mode will return the wiper to the position contained in the wiper register and close the L terminal. A RST will also deassert shutdown mode and return the wiper to midscale (0x80). This command does not affect the charge-pump status. SD_L_MID Command Moves wiper to midscale position (0x80) and opens the L terminal. The wiper register remains unaltered. Writes cannot be made to the wiper register while shutdown mode is engaged. Clearing shutdown mode will return the wiper to the position contained in the wiper register and close the L terminal. A RST will also deassert shutdown mode and return the wiper to midscale (0x80). This command does not affect the charge-pump status. SD_L_FULL Command Moves wiper to full-scale position (0xFF) and opens the L terminal. The wiper register remains unaltered. Writes cannot be made to the wiper register while shutdown mode is engaged. Clearing shutdown mode will return the wiper to the position contained in the wiper register and close the L terminal. A RST will also deassert shutdown mode and return the wiper to midscale (0x80). This command does not affect the charge-pump status. SD_W Command Opens the W terminal keeping the internal tap position the same as the wiper register. Writes cannot be made to the wiper registers while shutdown mode is engaged. Clearing shutdown mode will return the wiper to the position contained in the wiper register and close W terminal. A RST will also deassert shutdown mode and return the wiper to midscale (0x80). This command does not affect the charge-pump status. QP_OFF Command Disables the onboard charge pump and places device in low power mode. Low supply voltage is limited to 2.6V. QP_ON Command Enables the onboard charge pump to allow low-supply voltage operation. This is the power-on default condition. Low supply voltage is 1.7V. RST Command Returns the device to power-on default conditions. Resets the wiper register to midscale (0x80), enables charge pump, and deasserts any shutdown modes. 15 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer Ordering Information PIN-PACKAGE INTERFACE TAPS END-TO-END RESISTANCE (kI) MAX5395LATA+T 8 TDFN-EP* 256 10 MAX5395MATA+T 8 TDFN-EP* I2C I2C 256 50 MAX5395NATA+T 8 TDFN-EP* I2C 256 100 PART Note: All devices operate over the -40°C to +125°C temperature range. +Denotes a lead(Pb)-free/RoHS-compliant package. T = Tape and reel. *EP = Exposed pad. Chip Information PROCESS: BiCMOS Package Information For the latest package outline information and land patterns (footprints), go to www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 8 TDFN-EP T822+2 21-0168 90-0065 16 MAX5395 Single, 256-Tap Volatile, I2C, Low-Voltage Linear Taper Digital Potentiometer Revision History REVISION NUMBER REVISION DATE 0 7/12 DESCRIPTION Initial release PAGES CHANGED — Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated Products, Inc. 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 © 2012 Maxim Integrated Products 17 Maxim is a registered trademark of Maxim Integrated Products Inc.