NJG1704V 800MHz BAND FRONT-END GaAs MMIC nGENERAL DESCRIPTION NJG1704V is a front-end GaAs MMIC including a LNA, local amplifier and MIXER, designed mainly for 800MHz band cellular phone. NJG1704V exhibits low noise of 1.7dB at low total current consumption of 9.0mA. nPACKAGE OUTLINE NJG1704V nFEATURES lLow voltage operation lLow current consumption lHigh conversion gain lLow noise figure lHigh IIP3 lPackage +2.7V typ. 9mA typ. 28dB typ. @fRF=820MHz, PRF=-50dBm, f LO=690MHz, PLO=-10dBm 1.7dB typ. @fRF=820MHz, f LO=690MHz, PLO=-10dBm -14dBm typ. @f RF=820.0+820.1MHz, f LO=690MHz, PLO=-10dBm SSOP10 nPIN CONFIGURATION V TYPE (Top View) Pin Connection 1 10 2 9 3 8 4 7 1.LNAIN 2.LNACAP 3.GND 4.IFOUT 5.VLO 6.LOIN 7.GND 5 6 8.MIXIN 9.GND 10.LNAOUT -1- NJG1704V nABSOLLUTE MAXIMUM RATINGS PARAMETER LNA Voltage MIXER Voltage LOCAL Amplifier Voltage Input Power 1 Input Power 2 Power Dissipation Operating Temperature Storage Temperature (Ta=+25°C, Zs=Zl=50Ω) RATINGS UNITS 5.0 V 5.0 V 5.0 V +15 dBm +10 dBm 320 mW -40~+85 °C -55~+125 °C SYMBOL CONDITIONS VLNA VMIX VLO PLNAIN VLNA=VMIX=VLO=2.7V PLOIN VLNA=VMIX=VLO=2.7V PD Topr Tstg nELECTRICAL CHARACTERISTICS COMMON CONDITIONS: Ta=+25°C, VLNA=VMIX=VLO=2.7V, fRF=820MHz, f LO=690MHz, PRF=-50dBm PLO=-10dBm, Zs=Zl=50Ω, Application Circuit, f LO=690MHz PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Operating Frequency Freq 800 820 900 MHz LNA Voltage VLNA 2.5 2.7 4.5 V MIXER Voltage VMIX 2.5 2.7 4.5 V LOCAL Amplifier Voltage VLO 2.5 2.7 4.5 V LNA Current ILNA PRF, PLO=OFF 3.0 4.5 mA MIXER Current IMIX PRF, PLO=OFF 5.0 6.7 mA LOCAL Amplifier Current ILO PRF, PLO=OFF 1.0 2.0 mA Total Current IAL PRF, PLO=OFF 9.0 13.2 mA Conversion Gain Gc 25.0 28.0 dB 30MHz bandwidth in 1.5 dB Gain Flatness Gflat fRF=810~885MHz Noise Figure NF 1.7 2.0 dB 1dB Gain Compression P-1dB -1.0 +2.5 dBm Output Power Input 3rd Intercept Point IIP3 fRF=820.0+820.1MHz -19.0 -14.0 dBm Image Suppression Level RF IN VSWR -2- IMR - -22.0 -18.0 VSWRi - 2.0 3.0 dBc NJG1704V n ELECTRICAL CHARACTERISTICS (LNA) COMMON CONDITIONS: Ta=+25°C, VLNA=2.7V, VMIX=VLO=0V, fRF=820MHz, Zs=Zl=50Ω Application Circuit, f LO=690MHz PARAMETER SYMBOL CONDITIONS MIN TYP MAX Small Signal Gain Gain 16.0 Noise Figure NF 1.4 Input 3’rd Intercept Point IIP3 fRF=820.0+820.1MHz -3.0 2.0 RF IN VSWR VSWRi RF OUT VSWR VSWRo 2.0 - UNITS dB dB dBm n ELECTRICAL CHARACTERISTICS (MIXER) COMMON CONDITIONS: Ta=+25°C, VLNA=0V, VMIX=VLO=2.7V, fRF=820MHz, f LO=690MHz, PRF=-30dBm, PLO=-10dBm, Zs=Zl=50Ω Application Circuit, fLO=690MHz PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 12.0 dB Conversion Gain Gc Noise Figure NF 5.0 dB Input 3’rd Intercept Point IIP3 fRF=820.0+820.1MHz +2.0 dBm - -3- NJG1704V n TERMINAL INFORMATION No. SYMBOL 1 LNAIN 2 LNACAP 3 GND 4 IFOUT 5 VLO 6 LOIN 7 GND Ground terminal(0V) 8 MIXIN RF signal input terminal of Mixer. The RF signal from LNA is sent to Mixer through matching circuit. 9 GND Ground terminal(0V) 10 LNAOUT DESCRIPTIONS RF input terminal of LNA. The RF signal is input through external matching circuit. Terminal for the bypass capacitor of LNA. The bypass capacitor C1 shown in application circuit, should be connected to this terminal as close as possible. Ground terminal(0V) IF signal output terminal. The IF signal is output though external matching circuit’s connected to this terminal. Please connect inductance L8 and power supply as application circuit since it is also the terminal of Mixer power supply. Power supply terminal for local amplifier. Please connect R1 and L10 to this terminal shown in the application circuit as close as possible. Local signal input terminal of local amplifier. The local signal input to Local Amplifier through external matching circuit. Signal output terminal of LNA. The RF signal from LNA is output through external matching circuit connected to this terminal. Please connect inductance L4 and power supply shown in application circuit, since it is also the terminal of LNA power supply. CAUTION 1) Ground terminal (No.3, 7, 9) should be connected to the ground plane as short as possible. -4- NJG1704V n TYPICAL CHARACTERISTICS (LNA+MIXER, fLO=690MHz) Conversion Gain , Noise Figure vs. LO Power 2 30 Gc 4.5 1.9 26 1.8 NF 24 1.7 22 1.6 Conversion Gain (dB) 28 28 Noise Figure (dB) Conversion Gain (dB) 30 4 Gc 26 3.5 24 3 22 2.5 20 2 NF 18 20 780 800 820 840 860 880 900 16 -40 1.5 920 RF Frequency (MHz) 1.5 1 -30 -20 -10 0 10 LO Power (dBm) Condition fIF=130MHz PRF=-46dBm PLO=-10dBm VLNA=VMIX=VLO=2.7V Condition fIF=130MHz fRF=820MHz, PRF=-46dBm fLO=690MHz VLNA=VMIX=VLO=2.7V Output-IP3 , Input-IP3 vs. LO Power -8 15 OIP3 OIP3 (dBm) IIP3 5 -16 0 -20 -5 -40 IIP3 (dBm) -12 10 -24 -30 -20 -10 0 10 LO Power (dBm) Condition fIF=130MHz fRF1=820.0MHz, PRF=-42dBm fRF2=820.1MHz fLO=690MHz VLNA=VMIX=VLO=2.7V OIP3= 3IF-IM3 2 3IF-IM3 IIP3= -Gc 2 @PRF=-42dBm -5- Noise Figure (dB) Conversion Gain , Noise Figure vs. RF Frequency NJG1704V n TYPICAL CHARACTERISTICS (LNA+MIXER, fLO=690MHz) RF IN IMPEDANCE Condition VLNA=2.7V VMIX=VLO=2.7V Marker1: 810MHz Marker2: 850MHz Marker3: 885MHz IF OUT IMPEDANCE Condition VLNA=2.7V VMIX=VLO=2.7V -6- LOCAL IN IMPEDANCE Condition VLNA=2.7V VMIX=VLO=2.7V Marker1: 680MHz Marker2: 720MHz Marker3: 755MHz NJG1704V n TYPICAL CHARACTERISTICS (LNA+MIXER, fLO=690MHz) Output-IP3 , Input-IP3 vs. V ,V ,V Conversion Gain , Noise Figure vs. V ,V ,V 27 3.5 15 3 14 2.5 26 2 NF 25 1.5 24 1 23 1.5 2 2.5 3 V 3.5 LNA ,V MIX 4 ,V LO 4.5 5 0.5 5.5 MIX -10 OIP3 -12 13 IIP3 -14 12 -16 11 -18 10 -20 9 1.5 2 2.5 3 V (V) LNA 3.5 ,V MIX Condition fIF=130MHz fRF1=820.0MHz, PRF=-42dBm fRF2=820.1MHz fLO=690MHz, PLO=-10dBm Condition fIF=130MHz fRF=820MHz, PRF =-46dBm fLO=690MHz, PLO=-10dBm LO IF , IM3 vs. RF Power 4 ,V LO 4.5 5 -22 5.5 (V) OIP3= 3IF-IM3 2 3IF-IM3 IIP3= -Gc 2 @PRF=-42dBm IF vs. RF Power 20 10 5 IF 0 -20 IF (dBm) IF , IM3 (dBm) 0 -40 IM3 -5 -10 -15 -60 -20 -80 -50 -40 -30 -20 RF Power (dBm) Condition fIF=130MHz fRF1=820.0MHz fRF2=820.1MHz fLO=690MHz,PLO=-10dBm VLNA=VMIX=VLO=2.7V -10 0 -25 -50 -40 -30 -20 -10 0 RF Power (dBm) Condition fIF=130MHz fRF=820MHz fLO=690MHz,PLO=-10dBm VLNA=VMIX=VLO=2.7V -7- IIP3 (dBm) Conversion Gain (dB) Gc 28 LNA LO OIP3 (dBm) MIX Noise Figure (dB) LNA 29 NJG1704V n TYPICAL CHARACTERISTICS (LNA+MIXER, fLO=690MHz) Output-IP3 , Input-IP3 vs. Temperature 30 2.5 Gc 29 NF 2 28 1.5 27 1 26 0.5 25 -50 0 50 0 100 ,I MIX ,I LO I vs. Temperature (mA) LO ,I MIX ,I I LNA 3 2 I LNA MIX 5 4 I LO 1 0 -50 0 50 o Temperature ( C) Condition PRF=OFF PLO=OFF VLNA=VMIX=VLO=2.7V -8- -12 13 -13 IIP3 12 -14 11 -15 10 -50 0 Condition fIF=130MHz fRF1=820.0MHz, PRF=-42dBm fRF2=820.1MHz fLO=690MHz VLNA=VMIX=VLO=2.7V 7 6 OIP3 -16 100 50 Temperature ( C) Condition fIF=130MHz fRF=820MHz, PRF=-46dBm fLO=690MHz, PLO=-10dBm VLNA=VMIX=VLO=2.7V LNA 14 -11 o o Temperature ( C) I 15 100 OIP3= 3IF-IM3 2 3IF-IM3 IIP3= -Gc 2 @PRF=-42dBm IIP3 (dBm) 3 OIP3 (dBm) 31 Noise Figure (dB) Conversion Gain (dB) Conversion Gain , Noise Figure vs. Temperature NJG1704V n TYPICAL CHARACTERISTICS (LNA+MIXER, fLO=690MHz) RF OUT - MIXER IN ISOLATION (RF OUT-MIXER IN) RF IN - LOCAL IN ISOLATION (RF IN-LOCAL IN) Condition VLNA=2.7V VMIX=VLO=2.7V Port1: RF IN Port2: LOCAL IN Condition VLNA=2.7V VMIX=VLO=2.7V Port1:RF OUT Port2:MIXER IN Marker1: 810MHz Marker2: 850MHz Marker3: 885MHz Marker1: 810MHz Marker2: 850MHz Marker3: 885MHz n TYPICAL CHARACTERISTICS (LNA+MIXER fLO=1016.7MHz) Conversion Gain , Noise Figure vs. RF Frequency Gc 28 4 0 3 27 NF 26 25 865 20 2 1 870 875 880 885 RF Frequency (MHz) Condition fIF=135.2MHz PRF=-50dBm PLO=-8dBm VLNA=VMIX=VLO=3.0V Upper LOCAL 890 0 895 IF IF , IM3 (dBm) 29 IF , IM3 vs. RF Power 5 Noise Figure (dB) Conversion Gain (dB) 30 -20 -40 -60 -80 -50 IM3 -40 -30 -20 -10 0 RF Power (dBm) Condition fIF=135.2MHz fRF1=881.5MHz fRF2=881.6MHz fLO=1016.7MHz,PLO=-8dBm VLNA=VMIX=VLO=3.0V -9- NJG1704V n TYPICAL CHARACTERISTICS (LNA) SMALL SIGNAL GAIN (S21) Condition VLNA=2.7V VMIX=VLO=0V Marker1:810MHz Marker2:850MHz Marker3:885MHz RF OUT RETURN LOSS (S22) Condition VLNA=2.7V VMIX=VLO=0V - 10 - Marker1:810MHz Marker2:850MHz Marker3:885MHz RF IN RETURN LOSS (S11) Condition VLNA=2.7V VMIX=VLO=0V Marker1:810MHz Marker2:850MHz Marker3:885MHz ISOLATION (S12) Condition VLNA=2.7V VMIX=VLO=0V Marker1:810MHz Marker2:850MHz Marker3:885MHz NJG1704V n TYPICAL CHARACTERISTICS (LNA) Noise Figure vs. RF Frequency Pout , IM3 vs. RF Power 3 20 0 Pout , IM3 (dBm) Noise Figure (dB) 2.5 2 NF 1.5 1 Pout -20 -40 IM3 -60 0.5 0 780 800 820 840 860 880 900 -80 -40 920 -35 RF Frequency (MHz) -30 -25 -20 -15 -10 -5 0 RF Power (dBm) Condition VLNA=2.7V VMIX=VLO=0V Condition fRF=820.0+820.1MHz VLNA=2.7V VMIX=VLO=0V n TYPICAL CHARACTERISTICS (MIXER) Conversion Gain , Noise Figure vs. RF Frequency 14 Gc 8 7 8 6 NF 6 5 4 4 800 820 840 860 880 RF Frequency (MHz) Condition fIF=130MHz PRF=-30dBm PLO=-10dBm VLNA=0V VMIX=VLO=2.7V 900 3 920 IF , IM3 (dBm) 10 0 Noise Figure (dB) Conversion Gain (dB) 12 2 780 IF , IM3 vs. RF Power 20 9 IF -20 -40 IM3 -60 -80 -40 -35 -30 -25 -20 -15 -10 -5 0 RF Power (dBm) Condition fIF=130MHz fRF=820MHz, PRF=-30dBm fLO=690MHz VLNA=0V VMIX=VLO=2.7V - 11 - NJG1704V n TYPICAL CHARACTERISTICS (MIXER, fLO=690MHz) MIXER IN IMPEDANCE Condition VLNA=0V VMIX=VLO=2.7V Marker1:810MHz Marker2:850MHz Marker3:885MHz IF OUT IMPEDANCE Condition VLNA=0V VMIX=VLO=2.7V - 12 - LOCAL IN IMPEDANCE Condition VLNA=0V VMIX=VLO=2.7V Marker1:680MHz Marker2:720MHz Marker3:755MHz NJG1704V C3 L1 L2 RF IN Zo=50Ω L3 1 10 2 9 3 8 4 7 5 6 C1 VLNA L4 C2 L5 C6 IF Zo=50Ω L7 L8 C5 VMIX C8 C7 MIXER IN L9 R1 C9 L6 RF OUT Zo=50Ω n APPLICATION CIRCUIT C4 L10 LOCAL Zo=50Ω VL C11 C10 PARTS LIST 800MHz band Lower Upper Upper LOCAL LOCAL LOCAL PART ID COMMENT fLO=690MHz fLO=950MHz fLO=1016.7MHz fIF=130MHz fIF=130MHz fIF=135.2MHz L1 12nH 12nH 12nH TAIYO-YUDEN (HK1608) L2 15nH 15nH 15nH TAIYO-YUDEN (HK1608) L3 27nH 27nH 27nH TAIYO-YUDEN (HK1005) L4 12nH 12nH 12nH TAIYO-YUDEN (HK1005) L5 33nH 33nH 27nH TAIYO-YUDEN (HK1005) L6 22nH 22nH 22nH TAIYO-YUDEN (HK1005) L7 100nH 100nH 100nH TAIYO-YUDEN (HK1608) L8 56nH 56nH 47nH TAIYO-YUDEN (HK1608) L9 22nH 15nH 12nH TAIYO-YUDEN (HK1005) L10 33nH 33nH 22nH TAIYO-YUDEN (HK1005) C1 24pF 24pF 24pF MURATA (GRM36) C2 4pF 4pF 4pF MURATA (GRM36) C3 1000pF 1000pF 1000pF MURATA (GRM36) C4 1pF 1pF 1pF MURATA (GRM36) C5 9pF 9pF 9pF MURATA (GRM36) C6 1000pF 1000pF 1000pF MURATA (GRM36) C7 10pF 10pF 10pF MURATA (GRM36) C8 100pF 100pF 100pF MURATA (GRM36) C9 1000pF 1000pF 1000pF MURATA (GRM36) C10 100pF 100pF 100pF MURATA (GRM36) C11 1000pF 1000pF 1000pF MURATA (GRM36) R1 TAMA Electronics (CRG16G) 22Ω 22Ω 22Ω * L1 and L2 are possible to use swaller chip, but NF will be worce. - 13 - NJG1704V n RECOMMENDED PCB DESIGN (Top View) LNAIN VLNA C2 VMIX L3 L2 C8 L4 C3 C9 L1 C7 L8 C5 L5 C1 L6 C6 L7 PCB (FR-4): t=0.2mm STRIP LINE WIDTH =0.4mm (Z0=50Ω) PCB SIZE =23.0 x 17.0mm L10 IFOUT C4 R1 L9 C10 VLO C11 LOIN Caution on using devices. - 14 - [1] Please place R1 close to the VLO terminal (5th pin), and L10 to the R1. [2] Please place C1 close to the LNACAP terminal (2nd pin) [3] Please place C3 close to L4. [4] Please place C5 close to C7, C8, and C9. [5] Please place L10 close to C10, C11. NJG1704V n MEASURING BLOCK DIAGRAM VLNA,VMIX,VLO=2.7V SG (LOCAL) LOIN IFOUT D.U.T. PCB Spectrum Analyzer LNAIN SG (RF) Conversion Gain Measurement Block Diagram VLNA,VMIX,VLO=2.7V BPF SG (LOCAL) LOIN IFOUT D.U.T. PCB NF Meter LNAIN Noise Source BPF Noise Figure Measurement Block Diagram VLNA,VMIX,VLO=2.7V SG (LOCAL) LOIN D.U.T. PCB IFOUT Spectrum Analyzer LNAIN SG (RF1) Power Comb. ATT SG (RF2) IF, IM3, IM5 Measurement Block Diagram - 15 - NJG1704V nPACKAGE OUTLINE (SSOP10) Lead material Lead surface finish Molding material UNIT Weight Cautions on using this product This product contains Gallium-Arsenide (GaAs) which is a harmful material. • Do NOT eat or put into mouth. • Do NOT dispose in fire or break up this product. • Do NOT chemically make gas or powder with this product. • To waste this product, please obey the relating law of your country. This product may be damaged with electric static discharge (ESD) or spike voltage. Please handle with care to avoid these damages. - 16 - : Copper : Solder plating : Epoxy resin : mm : 41mg [CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights.