AD AD7503SE Cmos 4-/8-channel analog multiplexer Datasheet

a
CMOS
4-/8-Channel Analog Multiplexers
AD7501/AD7502/AD7503
FEATURES
DTL/TTL/CMOS Direct Interface
Power Dissipation: 30 ␮W
R ON: 170 ⍀
Standard 16-Lead DlPs and 20-Terminal Surface
Mount Packages
FUNCTIONAL BLOCK DIAGRAM
AD7501/AD7503
GENERAL DESCRIPTION
The AD7501 and AD7503 are monolithic CMOS, 8-channel
analog multiplexers which switch one of eight inputs to a
common output, depending on the state of three binary address
lines and an “enable” input. The AD7503 is identical to the
AD7501 except its “enable” logic is inverted. All digital inputs
are TTL/DTL and CMOS logic compatible.
The AD7502 is a monolithic CMOS dual 4-channel analog
multiplexer. Depending on the state of two binary address
inputs and an “enable,” it switches two output buses to two
of eight inputs.
AD7502
Truth Tables
AD7501
A2
A1
A0
EN
“ON”
0
0
0
0
1
1
1
1
X
0
0
1
1
0
0
1
1
X
0
1
0
1
0
1
0
1
X
1
1
1
1
1
1
1
1
0
1
2
3
4
5
6
7
8
None
AD7502
AD7503
A2
A1
A0
EN
“ON”
Al
A0
EN
“ON”
0
0
0
0
1
1
1
1
X
0
0
1
1
0
0
1
1
X
0
1
0
1
0
1
0
1
X
0
0
0
0
0
0
0
0
1
1
2
3
4
5
6
7
8
None
0
0
1
1
X
0
1
0
1
X
1
1
1
1
0
1&5
2&6
3&7
4&8
None
REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective companies.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© 2003 Analog Devices, Inc. All rights reserved.
AD7501/AD7502/AD7503–SPECIFICATIONS (V
ANALOG SWITCH
RON
RON vs. VS
RON vs. Temperature
∆RON Between Switches
RON vs. Temperature Between
Switches
IS
IOUT
|IOUT – IS|
= +15 V, VSS = –15 V unless otherwise noted.)
Over Specified
Temperature Range
@ +25°C
Parameter
DD
Version1
Switch
Condition
AD7501, AD7503
AD7502
All
All
All
All
ON
ON
ON
ON
170 Ω typ, 300 Ω max
20% typ
0.5%/°C typ
4% typ
170 Ω typ, 300 Ω max
20% typ
0.5%/°C typ
4% typ
All
K
S
K
ON
OFF
OFF
OFF
± 0.01%/°C
0.2 nA typ, 2 nA max
0.5 nA max
1 nA typ, 10 nA max
± 0.01%/°C
0.2 nA typ, 2 nA max
0.5 nA max
0.6 nA typ, 5 nA max
50 nA max
50 nA max
250 nA max
50 nA max
50 nA max
125 nA max
S
OFF
5 nA max
3 nA max
250 nA max
125 nA max
K
S
ON
ON
12 nA max
5.5 nA max
7 nA max
3.5 nA max
300 nA max
300 nA max
175 nA max
175 nA max
0.8 V max
2.4 V min
0.8 V max
2.4 V min
DIGITAL CONTROL
VINL
VINH
IINL or IINH
CIN
All
All
All
All
10 nA typ
3 pF typ
10 nA typ
3 pF typ
DYNAMIC CHARACTERISTICS
tON
tOFF
CS
COUT
CSOUT
CSS Between Any Two Switches
All
All
All
All
All
All
0.8 µs typ
0.8 µs typ
5 pF typ
30 pF typ
0.5 pF typ
0.5 pF typ
0.8 µs typ
0.8 µs typ
5 pF typ
15 pF typ
0.5 pF typ
0.5 pF typ
POWER SUPPLY
IDD
ISS
IDD
ISS
All
All
All
All
500 µA max
500 µA max
800 µA max
800 µA max
500 µA max
500 µA max
800 µA max
800 µA max
OFF
OFF
OFF
OFF
AD7501,
AD7503
AD7502
Test Conditions
–10 V ≤ VS ≤ +10 V
IS = 1.0 mA
VS = 0 V, IS = 1.0 mA
VS = –10 V, VOUT = +10 V and
VS = +10 V, VOUT = –10 V
VS = –10 V, VOUT = +10 V and
VS = +10 V, VOUT = –10 V
AD7501/02: Enable LOW
AD7503: Enable HIGH
VS = 0
VIN = 0 to +5.0 V
(See Test Circuit 2)
500 µA max
500 µA max
800 µA max
800 µA max
500 µA max
500 µA max
800 µA max
800 µA max
All Digital Inputs Low
All Digital Inputs High
NOTES
1
KN version specified for 0°C to +70°C, KQ version for –25°C to +85°C; and SQ, SE versions for –55°C to +125°C.
Specifications subject to change without notice.
Operating Temperature
Commercial (KN Version) . . . . . . . . . . . . . . . 0°C to +70°C
Industrial (KQ Version) . . . . . . . . . . . . . . . –25°C to +85°C
Extended (SQ, SE Versions) . . . . . . . . . . –55°C to +125°C
Storage Temperature . . . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . +300°C
ABSOLUTE MAXIMUM RATINGS
(TA = +25°C unless otherwise noted)
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +17 V
VSS to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –17 V
V Between Any Switch Terminals1 . . . . . . . . . . . . . . . . . 25 V
Digital Input Voltage Range . . . . . . . . . . . . . . . VDD to GND
Overvoltage at VOUT (VS) . . . . . . . . . . . . . . . . . . . . . . VSS, VDD
Switch Current (IS, Continuous One Channel) . . . . . . .35 mA
Switch Current (IS, Surge One Channel)
1 ms Duration, 10% Duty Cycle . . . . . . . . . . . . . . . 50 mA
Power Dissipation (Any Package)
Up to +75°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450 mW
Derates above +75°C by . . . . . . . . . . . . . . . . . . . 6 mW/°C
CAUTION
1
Do not apply voltages higher than V DD and V SS to any other terminal, especially
when VSS = VDD = 0 V all other pins should be at 0 V.
2
The digital control inputs are diode protected; however, permanent damage may
occur on unconnected units under high energy electrostatic fields. Keep unused
units in conductive foam at all times.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
AD7501, AD7502, and AD7503 feature proprietary ESD protection circuitry, permanent damage
may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
–2–
REV. B
AD7501/AD7502/AD7503
ORDERING GUIDE
PIN CONFIGURATIONS
Modell
Temperature
Range
Package
Options2
AD7501KN
AD7501KQ
AD7501SQ
AD7501SE
0°C to +70°C
–25°C to +85°C
–55°C to +125°C
–55°C to +125°C
N-16
Q-16
Q-16
E-20A
AD7502KN
AD7502KQ
AD7502SQ
AD7502SE
0°C to +70°C
–25°C to +85°C
–55°C to +125°C
–55°C to +125°C
N-16
Q-16
Q-16
E-20A
AD7503KN
AD7503KQ
AD7503SQ
AD7503SE
0°C to +70°C
–25°C to +85°C
–55°C to +125°C
–55°C to +125°C
N-16
Q-16
Q-16
E-20A
PDIP
CERDIP
LCC
NOTES
1
To order MIL-STD-883, Class B processed parts, add/883B to part number.
See the Analog Devices’ 1990 Military Databook for military data sheet.
2
E = LCC; N = PDIP; Q = CERDIP.
Typical Performance Characteristics
Figure 1a. RON vs. VS At Different Power
Supplies
Figure 1b. RON vs. VS At Different
Temperatures
REV. B
Figure 2a. Digital Threshold Voltage
(VINH, VINL) vs. Power Supply
Figure 3. tON, tOFF vs. Digital Input
Voltage
Figure 2b. Digital Threshold Voltage
(VINH, VINL) vs. Temperature
Figure 4. Power Dissipation vs. Logic
Frequency (50% Duty Cycle)
–3–
AD7501/AD7502/AD7503
OUTLINE DIMENSIONS
TYPICAL SWITCHING CHARACTERISTICS
16-Lead Plastic Dual In-Line Package [PDIP]
(N-16)
TEST CIRCUIT 1
0.785 (19.94)
0.765 (19.43)
0.745 (18.92)
16
9
1
8
C01129-0-7/03(B)
Dimensions shown in inches and (millimeters)
0.295 (7.49)
0.285 (7.24)
0.275 (6.99)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.100 (2.54)
BSC
0.015 (0.38)
MIN
0.150 (3.81)
0.135 (3.43)
0.120 (3.05)
0.180 (4.57)
MAX
0.150 (3.81)
0.130 (3.30)
0.110 (2.79)
1 µs/DIV
1 µs/DIV
0.015 (0.38)
0.010 (0.25)
0.008 (0.20)
0.060 (1.52) SEATING
PLANE
0.050 (1.27)
0.045 (1.14)
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
COMPLIANT TO JEDEC STANDARDS MO-095AC
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
16-Lead Ceramic Dual In-Line Package [CERDIP]
(Q-16)
Dimensions shown in inches and (millimeters)
TEST CIRCUIT 2
0.098 (2.49)
MAX
0.005
(0.13)
MIN
16
9
0.310 (7.87)
0.220 (5.59)
PIN 1
1
0.200 (5.08)
MAX
8
0.840 (21.34) MAX
0.060 (1.52)
0.015 (0.38)
0.320 (8.13)
0.290 (7.37)
0.150 (3.81)
MIN
0.200 (5.08)
0.125 (3.18)
0.100
(2.54)
BSC
0.023 (0.58)
0.014 (0.36)
0.015 (0.38)
0.008 (0.20)
15
0
0.070 (1.78) SEATING
PLANE
0.030 (0.76)
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
1 µs/DIV
1 µs/DIV
20-Terminal Ceramic Leadless Chip Carrier [LCC]
(E-20A)
Dimensions shown in inches and (millimeters)
0.100 (2.54)
0.064 (1.63)
0.200 (5.08)
REF
0.100 (2.54) REF
0.015 (0.38)
MIN
0.075 (1.91)
REF
0.095 (2.41)
0.075 (1.90)
3
4
19
18 20
0.358 (9.09)
0.342 (8.69)
SQ
1 µs/DIV
0.358
(9.09)
MAX
SQ
0.088 (2.24)
0.054 (1.37)
0.011 (0.28)
0.007 (0.18)
R TYP
0.075 (1.91)
REF
0.055 (1.40)
0.045 (1.14)
1
BOTTOM
VIEW
14
13
0.028 (0.71)
0.022 (0.56)
0.050 (1.27)
BSC
8
9
45 TYP
0.150 (3.81)
BSC
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
–4–
REV. B
Similar pages