Page 1 of 5 ATG Electronics® Smart™ X36T RGB LED Wall Washer USER GUIDE Part Number HWW-X036T-038070-H1 HWW-X036T-038070-H2 NOTE: The purpose of this user guide is to explain the necessary steps for use of Smart™ X36T, and to assure peak performance of said product. It is intended for use as reference by a fully qualified electrician or technician. This document should never be considered a substitute for any provision of a regulation or state or local code. Please read this entire manual to fully understand and safely use this product. Specifications are subject to change without notice. Please visit www.atgelectronics.com for the most recent user guide versions. GETTING STARTED This guide contains important information about installing and operating your new Smart™ X36T safely and properly. Included in this Box Smart™ X36T RGB LED Wall Washer, 1 PCs User Guide, 1 Set Additional Items Needed Control System: DynColor™ 500-SL RGB DMX Controller Signal Amplifier: Master™ 192-SA Signal Amplifier Unpacking 1) Unpack and carefully examine the product. 2) Report any damage and save all packing materials if any part of the apparatus was damaged during shipping. 3) Do not attempt to use this apparatus if it is damaged. Cautions 1) Warning: Risk of electric shock! Ensure that the power supply is off when wiring or soldering the device during installation. 2) The device should be installed and operated by a qualified electrician or technician in accordance with relevant local codes. 3) Do not use sharp tools near or on the surface of the device. 4) Suggested continuous working time is around 8 hours. Never use for more than 12 consecutive hours. ATG Electronics Corp. Light your world Color your life! Page 2 of 5 User Responsibilities The responsibility of complying with all state and local laws, ordinances, and regulations in regards to the installation, maintenance, and operation of the device lies with the buyer and handler of the device. These parties may include, but are not limited to the contractor, installer, purchaser, owner, and user of the product. Note: The instructions and precautions set forth in this user guide are not necessarily inclusive of or relevant to all applications as ATG Electronics cannot anticipate all possible situations. PLANNING THE INSTALLATION This device installation requires planning to ensure timely installation with minimal complications and down time. Planning Suggestions Consult an electrical inspector when reviewing all wiring plans. Create a layout plan blueprint, per a lighting designer’s or architect’s recommendations. Consult ATG Electronics's Application Engineering Services as needed. Installation Considerations When creating your installation plan, consider the following: 1) Location of the device Smart™ X36T is suitable for only dry, wet and damp environments. 2) Control System Smart™ X36T can be controlled by DynColor™ 500-SL RGB DMX Controller. Synchronous color changing might be considered before installing. 3) Lighting Distance The maximum lighting distance for Smart™ X36T is around 20 meters (65 feet). 4) Maximum Series-wound Length 100 meters (328 feet). Master™ 192-SA Signal Amplifier is needed at every 100 meters (328 feet). Installation Steps 1) Place Smart™ X36T at the required locations and aim them according to your lighting design. 2) Adjust the rotary angle to required angle. 3) Connect Smart™ X36T to each other. Signal Amplifiers are needed every 100 meters or 328 feet. www.atgelectronics.com Page 3 of 5 4) Finish waterproof treatment at every signal connector joint. (Please refer to picture below). 5) Connect the DMX Console to the first Smart™ X36T. 6) Plug the first Smart™ X36T and DMX console into power outlets to power the system. Operation Instruction 1) Buttons Functions Button Control Mode DMX-Control Function Example Displays the DMX address selected (valid DMX addresses from 001~512) Displays the color-changing mode and Self-Control speed selected (P=self-control, X=mode, Y=speed) DMX-Control Select a parameter for configuration - Self-Control Select mode or speed for configuration - DMX-Control Set corresponding parameter - Self-Control Set corresponding mode/speed - 2) How to change settings in DMX-Control mode A. Once the wall washer is connected to the DMX console, it will access DMX-Control mode. B. Press button "A" to select a parameter for the DMX address. C. Press button "B" to change the DMX address. D. Valid DMX address range: 001~512. (Refer to the user guide of the DMX Console for more detailed information on operating the DMX Console.) E. Each wall washer occupies three DMX channels, including red, green, and blue. For example, the wall washer at DMX address 001 occupies channels 1, 2, and 3; the wall washer at DMX address 256 occupies channels 256, 257, and 258. 3) How to access and set under Self-Control mode A. Press button "A" four times. This will access Self-Control mode and the letters "PXY” will be displayed. B. Press button "A" once. The digital LED should start to flash and you will be given access to the corresponding setup (mode). C. Press button "B" to change the corresponding setup (speed or brightness). The digital LED should www.atgelectronics.com Page 4 of 5 display values 1 through 9. D. Master/Slave Mode: ① Choose one wall washer as the master and set its DMX address to 001. ② Choose other wall washers as slaves and assign them any DMX addresses except 001. ③ Press button "A" of the master wall washer four times to access Self-Control mode. ④ Change the mode of the master wall washer. All slave wall washers will work synchronously with the master. E. Parameter form of "PXY" P X (mode) - 1 (Static Red) Y (speed/brightness) 9 brightness levels, (brightest at 9) - 2 (Static Green) 9 brightness levels, (brightest at 9) - 3 (Static Yellow) 9 brightness levels, (brightest at 9) - 4 (Static Blue) 9 brightness levels, (brightest at 9) - 5 (Static Pink) 9 brightness levels, (brightest at 9) - 6 (Static Cyan) 9 brightness levels, (brightest at 9) - 7 (Static White) 9 brightness levels, (brightest at 9) - 8 (Multi-color jumping) 9 speed levels, (fastest at 9) - 9 (Multi-color fading) 9 speed levels, (fastest at 9) - A (Multi-color flashing) 9 speed levels, (fastest at 9) 4) How to exit the selected mode? Press a button of your choosing and wait for around 10 seconds for the device to exit from selected mode. The digital LED will stop flashing and the wall washer will retain the currently the selected mode and parameter. Wiring Diagram www.atgelectronics.com Page 5 of 5 ATG Electronics® Smart™ X36T RGB LED Wall Washer Specifications Input Voltage: 100 VAC~256 VAC Color: RGB LED Qty: 36 LEDs Lumens (single LED): 44 lm/W(Red), 70 lm/W(Green), 15 lm/W(Blue) Power Consumption: 55 W (Max.) Beam Angle: 15° Dimension: L333 * W147 * H210 mm (L13.11 * W5.79 * 8.27 inches) IP Rating: IP65 (applicable for dry, wet, damp environments) * For detailed specifications please refer to the product catalog of Smart™ X36T RGB LED Wall Washer. 628 Zhangyang Road, Suite 1-21B Shanghai 200122, CHINA www.atgelectronics.com E-mail: [email protected] Phone: +86-21-58350166 Fax: +86-21-58351977 Ver5.3-120420 ATG Electronics Corp. Light your world Color your life!