LM2578A, LM3578A www.ti.com SNVS767E – AUGUST 2000 – REVISED APRIL 2013 LM2578A/LM3578A Switching Regulator Check for Samples: LM2578A, LM3578A FEATURES DESCRIPTION • • • • The LM2578A is a switching regulator which can easily be set up for such DC-to-DC voltage conversion circuits as the buck, boost, and inverting configurations. The LM2578A features a unique comparator input stage which not only has separate pins for both the inverting and non-inverting inputs, but also provides an internal 1.0V reference to each input, thereby simplifying circuit design and p.c. board layout. The output can switch up to 750 mA and has output pins for its collector and emitter to promote design flexibility. An external current limit terminal may be referenced to either the ground or the Vin terminal, depending upon the application. In addition, the LM2578A has an on board oscillator, which sets the switching frequency with a single external capacitor from <1 Hz to 100 kHz (typical). 1 2 • • Inverting and Non-Inverting Feedback Inputs 1.0V Reference at Inputs Operates from Supply Voltages of 2V to 40V Output Current up to 750 mA, Saturation Less than 0.9V Current Limit and Thermal Shut Down Duty Cycle up to 90% APPLICATIONS • • • Switching Regulators in Buck, Boost, Inverting, and Single-Ended Transformer Configurations Motor Speed Control Lamp Flasher The LM2578A is an improved version of the LM2578, offering higher maximum ratings for the total supply voltage and output transistor emitter and collector voltages. Connection Diagram Figure 1. PDIP/SOIC Package See Package Number D0008A or P0008E 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2000–2013, Texas Instruments Incorporated LM2578A, LM3578A SNVS767E – AUGUST 2000 – REVISED APRIL 2013 www.ti.com Functional Diagram These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) Total Supply Voltage 50V −0.3V to +50V Collector Output to Ground Emitter Output to Ground (3) −1V to +50V (4) Internally limited Storage Temperature −65°C to +150°C Power Dissipation Output Current 750 mA Lead Temperature (soldering, 10 seconds) 260°C Maximum Junction Temperature ESD Tolerance (1) (2) (3) (4) (5) 150°C (5) 2 kV Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its rated operating conditions. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. For TJ ≥ 100°C, the Emitter pin voltage should not be driven more than 0.6V below ground (see Application Information). At elevated temperatures, devices must be derated based on package thermal resistance. The device in the 8-pin DIP must be derated at 95°C/W, junction to ambient. The device in the SOIC package must be derated at 150°C/W, junction-to-ambient. Human body model, 1.5 kΩ in series with 100 pF. Operating Ratings Ambient Temperature Range Junction Temperature Range 2 −40°C ≤ TA ≤+85°C LM2578A LM3578A 0°C ≤ TA ≤+70°C LM2578A −40°C ≤ TJ ≤+125°C LM3578A 0°C ≤ TJ ≤+125°C Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A LM2578A, LM3578A www.ti.com SNVS767E – AUGUST 2000 – REVISED APRIL 2013 Electrical Characteristics These specifications apply for 2V ≤ VIN ≤ 40V (2.2V ≤ VIN ≤ 40V for TJ ≤ −25°C), timing capacitor CT = 3900 pF, and 25% ≤ duty cycle ≤ 75%, unless otherwise specified. Values in standard typeface are for TJ = 25°C; values in boldface type apply for operation over the specified operating junction temperature range. Typical (1) Symbol Parameter Conditions LM2578A/ LM3578A Limit (2) Units OSCILLATOR fOSC ΔfOSC/ΔT Frequency 20 Frequency Drift with Temperature Amplitude kHz 24 kHz (max) 16 kHz (min) −0.13 %/°C 550 mVp-p REFERENCE/COMPARATOR (3) VR Input Reference Voltage I1 = I2 = 0 mA and I1 = I2 = 1 mA ±1% 1.0 (4) V 1.050/1.070 0.950/0.930 ΔVR/ΔVIN IINV I1 = I2 = 0 mA and Inverting Input Current I1 = I2 = 0 mA, duty cycle = 25% 0.5 μA Level Shift Accuracy Level Shift Current = 1 mA 1.0 % (4) %/V 0.01/0.02 10/13 ΔVR/Δt V (min) Input Reference Voltage Line Regulation I1 = I2 = 1 mA ±1% 0.003 V (max) Input Reference Voltage Long Term Stability 100 %/V (max) % (max) ppm/1000h OUTPUT VC (sat) Collector Saturation Voltage VE (sat) Emitter Saturation Voltage ICES Collector Leakage Current IC = 750 mA pulsed, Emitter grounded 0.7 IO = 80 mA pulsed, 1.4 VIN = VC = 40V BVCEO(SUS) Collector-Emitter Sustaining Voltage V 0.90/1.2 V 1.7/2.0 VIN = VCE = 40V, Emitter grounded, Output OFF 0.1 ISUST = 0.2A (pulsed), VIN = 0 60 V (max) V (max) μA 200/250 μA (max) V 50 V (min) CURRENT LIMIT VCL Sense Voltage Shutdown Level Referred to VIN or Ground See ΔVCL/ΔT Sense Voltage Temperature Drift ICL Sense Bias Current (1) (2) (3) (4) (5) 110 (5) mV 80 mV (min) 160 mV (max) 0.3 %/°C Referred to VIN 4.0 μA Referred to ground 0.4 μA Typical values are for TJ = 25°C and represent the most likely parametric norm. All limits specified at room temperature (standard type face) and at temperature extremes (bold type face). Room temperature limits are 100% production tested. Limits at temperature extremes are specified via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate AOQL. Input terminals are protected from accidental shorts to ground but if external voltages higher than the reference voltage are applied, excessive current will flow and should be limited to less than 5 mA. I1 and I2 are the external sink currents at the inputs (refer to Test Circuit). Connection of a 10 kΩ resistor from pin 1 to pin 4 will drive the duty cycle to its maximum, typically 90%. Applying the minimum Current Limit Sense Voltage to pin 7 will not reduce the duty cycle to less than 50%. Applying the maximum Current Limit Sense Voltage to pin 7 is certain to reduce the duty cycle below 50%. Increasing this voltage by 15 mV may be required to reduce the duty cycle to 0%, when the Collector output swing is 40V or greater (see Ground-Referred Current Limit Sense Voltage typical curve). Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A Submit Documentation Feedback 3 LM2578A, LM3578A SNVS767E – AUGUST 2000 – REVISED APRIL 2013 www.ti.com Electrical Characteristics (continued) These specifications apply for 2V ≤ VIN ≤ 40V (2.2V ≤ VIN ≤ 40V for TJ ≤ −25°C), timing capacitor CT = 3900 pF, and 25% ≤ duty cycle ≤ 75%, unless otherwise specified. Values in standard typeface are for TJ = 25°C; values in boldface type apply for operation over the specified operating junction temperature range. Typical (1) Symbol Parameter Conditions LM2578A/ LM3578A Limit (2) Units DEVICE POWER CONSUMPTION IS Supply Current Output OFF, VE = 0V 2.0 mA 3.5/4.0 Output ON, IC = 750 mA pulsed, 14 mA (max) mA VE = 0V 4 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A LM2578A, LM3578A www.ti.com SNVS767E – AUGUST 2000 – REVISED APRIL 2013 Typical Performance Characteristics Oscillator Frequency Change with Temperature Oscillator Voltage Swing Figure 2. Figure 3. Input Reference Voltage Drift with Temperature Collector Saturation Voltage (Sinking Current, Emitter Grounded) Figure 4. Figure 5. Emitter Saturation Voltage (Sourcing Current, Collector at Vin) Ground Referred Current Limit Sense Voltage Figure 6. Figure 7. Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A Submit Documentation Feedback 5 LM2578A, LM3578A SNVS767E – AUGUST 2000 – REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) 6 Current Limit Sense Voltage Drift with Temperature Current Limit Response Time for Various Over Drives Figure 8. Figure 9. Current Limit Sense Voltage vs Supply Voltage Supply Current Figure 10. Figure 11. Supply Current Collector Current with Emitter Output Below Ground Figure 12. Figure 13. Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A LM2578A, LM3578A www.ti.com SNVS767E – AUGUST 2000 – REVISED APRIL 2013 TEST CIRCUIT* Parameter tests can be made using the test circuit shown. Select the desired Vin, collector voltage and duty cycle with adjustable power supplies. A digital volt meter with an input resistance greater than 100 MΩ should be used to measure the following: Input Reference Voltage to Ground; S1 in either position. Level Shift Accuracy (%) = (TP3(V)/1V) × 100%; S1 at I1 = I2 = 1 mA Input Current (mA) = (1V − Tp3 (V))/1 MΩ: S1 at I1 = I2 = 0 mA. Oscillator parameters can be measured at Tp4 using a frequency counter or an oscilloscope. The Current Limit Sense Voltage is measured by connecting an adjustable 0-to-1V floating power supply in series with the current limit terminal and referring it to either the ground or the Vin terminal. Set the duty cycle to 90% and monitor test point TP5 while adjusting the floating power supply voltage until the LM2578A's duty cycle just reaches 0%. This voltage is the Current Limit Sense Voltage. The Supply Current should be measured with the duty cycle at 0% and S1 in the I1 = I2 = 0 mA position. *LM2578A specifications are measured using automated test equipment. This circuit is provided for the customer's convenience when checking parameters. Due to possible variations in testing conditions, the measured values from these testing procedures may not match those of the factory. Op amp supplies are ±15V DVM input resistance >100 MΩ *LM2578 max duty cycle is 90% Definition of Terms Input Reference Voltage: The voltage (referred to ground) that must be applied to either the inverting or noninverting input to cause the regulator switch to change state (ON or OFF). Input Reference Current: The current that must be drawn from either the inverting or non-inverting input to cause the regulator switch to change state (ON or OFF). Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A Submit Documentation Feedback 7 LM2578A, LM3578A SNVS767E – AUGUST 2000 – REVISED APRIL 2013 www.ti.com Input Level Shift Accuracy: This specification determines the output voltage tolerance of a regulator whose output control depends on drawing equal currents from the inverting and non-inverting inputs (see the Inverting Regulator of Figure 34, and the RS-232 Line Driver Power Supply of Figure 36). Level Shift Accuracy is tested by using two equal-value resistors to draw current from the inverting and noninverting input terminals, then measuring the percentage difference in the voltages across the resistors that produces a controlled duty cycle at the switch output. Collector Saturation Voltage: With the inverting input terminal grounded thru a 10 kΩ resistor and the output transistor's emitter connected to ground, the Collector SaturationVoltage is the collector-to-emitter voltage for a given collector current. Emitter Saturation Voltage: With the inverting input terminal grounded thru a 10 kΩ resistor and the output transistor's collector connected to Vin, the Emitter Saturation Voltage is the collector-to-emitter voltage for a given emitter current. Collector Emitter Sustaining Voltage: The collector-emitter breakdown voltage of the output transistor, measured at a specified current. Current Limit Sense Voltage: The voltage at the Current Limit pin, referred to either the supply or the ground terminal, which (via logic circuitry) will cause the output transistor to turn OFF and resets cycle-by-cycle at the oscillator frequency. Current Limit Sense Current: The bias current for the Current Limit terminal with the applied voltage equal to the Current Limit Sense Voltage. Supply Current: The IC power supply current, excluding the current drawn through the output transistor, with the oscillator operating. Functional Description The LM2578A is a pulse-width modulator designed for use as a switching regulator controller. It may also be used in other applications which require controlled pulse-width voltage drive. A control signal, usually representing output voltage, fed into the LM2578A's comparator is compared with an internally-generated reference. The resulting error signal and the oscillator's output are fed to a logic network which determines when the output transistor will be turned ON or OFF. The following is a brief description of the subsections of the LM2578A. COMPARATOR INPUT STAGE The LM2578A's comparator input stage is unique in that both the inverting and non-inverting inputs are available to the user, and both contain a 1.0V reference. This is accomplished as follows: A 1.0V reference is fed into a modified voltage follower circuit (see FUNCTIONAL DIAGRAM). When both input pins are open, no current flows through R1 and R2. Thus, both inputs to the comparator will have the potential of the 1.0V reference, VA. When one input, for example the non-inverting input, is pulled ΔV away from VA, a current of ΔV/R1 will flow through R1. This same current flows through R2, and the comparator sees a total voltage of 2ΔV between its inputs. The high gain of the system, through feedback, will correct for this imbalance and return both inputs to the 1.0V level. This unusual comparator input stage increases circuit flexibility, while minimizing the total number of external components required for a voltage regulator system. The inverting switching regulator configuration, for example, can be set up without having to use an external op amp for feedback polarity reversal (see TYPICAL APPLICATIONS). OSCILLATOR The LM2578A provides an on-board oscillator which can be adjusted up to 100 kHz. Its frequency is set by a single external capacitor, C1, as shown in Figure 14, and follows the equation fOSC = 8×10−5/C1 The oscillator provides a blanking pulse to limit maximum duty cycle to 90%, and a reset pulse to the internal circuitry. 8 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A LM2578A, LM3578A www.ti.com SNVS767E – AUGUST 2000 – REVISED APRIL 2013 Figure 14. Value of Timing Capacitor vs Oscillator Frequency OUTPUT TRANSISTOR The output transistor is capable of delivering up to 750 mA with a saturation voltage of less than 0.9V. (see Collector Saturation Voltage and Emitter Saturation Voltage curves). The emitter must not be pulled more than 1V below ground (this limit is 0.6V for TJ ≥ 100°C). Because of this limit, an external transistor must be used to develop negative output voltages (see the Inverting Regulator Typical Application). Other configurations may need protection against violation of this limit (see the Emitter Output section of the Applications Information). CURRENT LIMIT The LM2578A's current limit may be referenced to either the ground or the Vin pins, and operates on a cycle-bycycle basis. The current limit section consists of two comparators: one with its non-inverting input referenced to a voltage 110 mV below Vin, the other with its inverting input referenced 110 mV above ground (see FUNCTIONAL DIAGRAM). The current limit is activated whenever the current limit terminal is pulled 110 mV away from either Vin or ground. Applications Information CURRENT LIMIT As mentioned in the functional description, the current limit terminal may be referenced to either the Vin or the ground terminal. Resistor R3 converts the current to be sensed into a voltage for current limit detection. Figure 15. Current Limit, Ground Referred Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A Submit Documentation Feedback 9 LM2578A, LM3578A SNVS767E – AUGUST 2000 – REVISED APRIL 2013 www.ti.com Figure 16. Current Limit, Vin Referred CURRENT LIMIT TRANSIENT SUPPRESSION When noise spikes and switching transients interfere with proper current limit operation, R1 and C1 act together as a low pass filter to control the current limit circuitry's response time. Because the sense current of the current limit terminal varies according to where it is referenced, R1 should be less than 2 kΩ when referenced to ground, and less than 100Ω when referenced to Vin. Figure 17. Current Limit Transient Suppressor, Ground Referred Figure 18. Current Limit Transient Suppressor, Vin Referred C.L. SENSE VOLTAGE MULTIPLICATION When a larger sense resistor value is desired, the voltage divider network, consisting of R1 and R2, may be used. This effectively multiplies the sense voltage by (1 + R1/R2). Also, R1 can be replaced by a diode to increase current limit sense voltage to about 800 mV (diode Vf + 110 mV). 10 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A LM2578A, LM3578A www.ti.com SNVS767E – AUGUST 2000 – REVISED APRIL 2013 Figure 19. Current Limit Sense Voltage Multiplication, Ground Referred Figure 20. Current Limit Sense Voltage Multiplication, Vin Referred UNDER-VOLTAGE LOCKOUT Under-voltage lockout is accomplished with few external components. When Vin becomes lower than the zener breakdown voltage, the output transistor is turned off. This occurs because diode D1 will then become forward biased, allowing resistor R3 to sink a greater current from the non-inverting input than is sunk by the parallel combination of R1 and R2 at the inverting terminal. R3 should be one-fifth of the value of R1 and R2 in parallel. Figure 21. Under-Voltage Lockout MAXIMUM DUTY CYCLE LIMITING The maximum duty cycle can be externally limited by adjusting the charge to discharge ratio of the oscillator capacitor with a single external resistor. Typical values are 50 μA for the charge current, 450 μA for the discharge current, and a voltage swing from 200 mV to 750 mV. Therefore, R1 is selected for the desired charging and discharging slopes and C1 is readjusted to set the oscillator frequency. Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A Submit Documentation Feedback 11 LM2578A, LM3578A SNVS767E – AUGUST 2000 – REVISED APRIL 2013 www.ti.com Figure 22. Maximum Duty Cycle Limiting DUTY CYCLE ADJUSTMENT When manual or mechanical selection of the output transistor's duty cycle is needed, the cirucit shown below may be used. The output will turn on with the beginning of each oscillator cycle and turn off when the current sunk by R2 and R3 from the non-inverting terminal becomes greater than the current sunk from the inverting terminal. With the resistor values as shown, R3 can be used to adjust the duty cycle from 0% to 90%. When the sum of R2 and R3 is twice the value of R1, the duty cycle will be about 50%. C1 may be a large electrolytic capacitor to lower the oscillator frequency below 1 Hz. Figure 23. Duty Cycle Adjustment REMOTE SHUTDOWN The LM2578A may be remotely shutdown by sinking a greater current from the non-inverting input than from the inverting input. This may be accomplished by selecting resistor R3 to be approximately one-half the value of R1 and R2 in parallel. Figure 24. Shutdown Occurs when VL is High 12 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A LM2578A, LM3578A www.ti.com SNVS767E – AUGUST 2000 – REVISED APRIL 2013 EMITTER OUTPUT When the LM2578A output transistor is in the OFF state, if the Emitter output swings below the ground pin voltage, the output transistor will turn ON because its base is clamped near ground. The Collector Current with Emitter Output Below Ground curve shows the amount of Collector current drawn in this mode, vs temperature and Emitter voltage. When the Collector-Emitter voltage is high, this current will cause high power dissipation in the output transistor and should be avoided. This situation can occur in the high-current high-voltage buck application if the Emitter output is used and the catch diode's forward voltage drop is greater than 0.6V. A fast-recovery diode can be added in series with the Emitter output to counter the forward voltage drop of the catch diode (see Figure 15). For better efficiency of a high output current buck regulator, an external PNP transistor should be used as shown in Figure 29. Figure 25. D1 Prevents Output Transistor from Improperly Turning ON due to D2's Forward Voltage SYNCHRONIZING DEVICES When several devices are to be operated at once, their oscillators may be synchronized by the application of an external signal. This drive signal should be a pulse waveform with a minimum pulse width of 2 μs. and an amplitude from 1.5V to 2.0V. The signal source must be capable of 1.) driving capacitive loads and 2.) delivering up to 500 μA for each LM2578A. Capacitors C1 thru CN are to be selected for a 20% slower frequency than the synchronization frequency. Figure 26. Synchronizing Devices Typical Applications The LM2578A may be operated in either the continuous or the discontinuous conduction mode. The following applications (except for the Buck-Boost Regulator) are designed for continuous conduction operation. That is, the inductor current is not allowed to fall to zero. This mode of operation has higher efficiency and lower EMI characteristics than the discontinuous mode. Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A Submit Documentation Feedback 13 LM2578A, LM3578A SNVS767E – AUGUST 2000 – REVISED APRIL 2013 www.ti.com BUCK REGULATOR The buck configuration is used to step an input voltage down to a lower level. Transistor Q1 in Figure 27 chops the input DC voltage into a squarewave. This squarewave is then converted back into a DC voltage of lower magnitude by the low pass filter consisting of L1 and C1. The duty cycle, D, of the squarewave relates the output voltage to the input voltage by the following equation: Vout = D × Vin = Vin × (ton)/(ton + toff). Figure 27. Basic Buck Regulator Figure 28 is a 15V to 5V buck regulator with an output current, Io, of 350 mA. The circuit becomes discontinuous at 20% of Io(max), has 10 mV of output voltage ripple, an efficiency of 75%, a load regulation of 30 mV (70 mA to 350 mA) and a line regulation of 10 mV (12 ≤ Vin ≤ 18V). Component values are selected as follows: R1 = (Vo − 1) × R2 where R2 = 10 kΩ R3 = V/Isw(max) R3 = 0.15Ω where: V is the current limit sense voltage, 0.11V Isw(max) is the maximum allowable current thru the output transistor. L1 is the inductor and may be found from the inductance calculation chart (Figure 29) as follows: Given Vin = 15V Vo = 5V Io(max) = 350 mA fOSC = 50 kHz Discontinuous at 20% of Io(max). Note that since the circuit will become discontinuous at 20% of Io(max), the load current must not be allowed to fall below 70 mA. 14 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A LM2578A, LM3578A www.ti.com SNVS767E – AUGUST 2000 – REVISED APRIL 2013 Vin = 15V R3 = 0.15Ω Vo = 5V C1 = 1820 pF Vripple = 10 mV C2 = 220 μF Io = 350 mA C3 = 20 pF fosc = 50 kHz L1 = 470 μH R1 = 40 kΩ D1 = 1N5818 R2 = 10 kΩ Figure 28. Buck or Step-Down Regulator Figure 29. DC/DC Inductance Calculator Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A Submit Documentation Feedback 15 LM2578A, LM3578A SNVS767E – AUGUST 2000 – REVISED APRIL 2013 www.ti.com Step 1: Calculate the maximum DC current through the inductor, IL(max). The necessary equations are indicated at the top of the chart and show that IL(max) = Io(max) for the buck configuration. Thus, IL(max) = 350 mA. Step 2: Calculate the inductor Volts-sec product, E-Top, according to the equations given from the chart. For the Buck: E-Top = (Vin − Vo) (Vo/Vin) (1000/fosc) =(15 − 5) (5/15) (1000/50) = 66V-μs. with the oscillator frequency, fosc, expressed in kHz. Step 3: Using the graph with axis labeled “Discontinuous At % IOUT” and “IL(max, DC)” find the point where the desired maximum inductor current, IL(max, DC) intercepts the desired discontinuity percentage. In this example, the point of interest is where the 0.35A line intersects with the 20% line. This is nearly the midpoint of the horizontal axis. Step 4: This last step is merely the translation of the point found in Step 3 to the graph directly below it. This is accomplished by moving straight down the page to the point which intercepts the desired E-Top. For this example, E-Top is 66V-μs and the desired inductor value is 470 μH. Since this example was for 20% discontinuity, the bottom chart could have been used directly, as noted in step 3 of the chart instructions. For a full line of standard inductor values, contact Pulse Engineering (San Diego, Calif.) regarding their PE526XX series, or A. I. E. Magnetics (Nashville, Tenn.). A more precise inductance value may be calculated for the Buck, Boost and Inverting Regulators as follows: BUCK L = Vo (Vin − Vo)/(ΔIL Vin fosc) BOOST L = Vin (Vo − Vin)/(ΔIL fosc Vo) INVERT L = Vin |Vo|/[ΔIL(Vin + |Vo|)fosc] where ΔIL is the current ripple through the inductor. ΔIL is usually chosen based on the minimum load current expected of the circuit. For the buck regulator, since the inductor current IL equals the load current IO, ΔIL = 2 • IO(min) ΔIL = 140 mA for this circuit. ΔIL can also be interpreted as ΔIL = 2 • (Discontinuity Factor) • IL where the Discontinuity Factor is the ratio of the minimum load current to the maximum load current. For this example, the Discontinuity Factor is 0.2. The remainder of the components of Figure 28 are chosen as follows: C1 is the timing capacitor found in Figure 14. C2 ≥ Vo (Vin − Vo)/(8fosc2VinVrippleL1) where Vripple is the peak-to-peak output voltage ripple. C3 is necessary for continuous operation and is generally in the 10 pF to 30 pF range. D1 should be a Schottky type diode, such as the 1N5818 or 1N5819. BUCK WITH BOOSTED OUTPUT CURRENT For applications requiring a large output current, an external transistor may be used as shown in Figure 30. This circuit steps a 15V supply down to 5V with 1.5A of output current. The output ripple is 50 mV, with an efficiency of 80%, a load regulation of 40 mV (150 mA to 1.5A), and a line regulation of 20 mV (12V ≤ Vin ≤ 18V). 16 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A LM2578A, LM3578A www.ti.com SNVS767E – AUGUST 2000 – REVISED APRIL 2013 Component values are selected as outlined for the buck regulator with a discontinuity factor of 10%, with the addition of R4 and R5: R4 = 10VBE1Bf/Ip R5 = (Vin − V − VBE1 − Vsat) Bf/(IL(max, DC) + IR4) where: VBE1 is the VBE of transistor Q1. Vsat is the saturation voltage of the LM2578A output transistor. V is the current limit sense voltage. Bf is the forced current gain of transistor Q1 (Bf = 30 for Figure 30). IR4 = VBE1/R4 Ip = IL(max, DC) + 0.5ΔIL Vin = 15V R4 = 200Ω Vo = 5V R5 = 330Ω Vripple = 50 mV C1 = 1820 pF Io = 1.5A C2 = 330 μF fosc = 50 kHz C3 = 20 pF R1 = 40 kΩ L1 = 220 μH R2 = 10 kΩ D1 = 1N5819 R3 = 0.05Ω Q1 = D45 Figure 30. Buck Converter with Boosted Output Current BOOST REGULATOR The boost regulator converts a low input voltage into a higher output voltage. The basic configuration is shown in Figure 31. Energy is stored in the inductor while the transistor is on and then transferred with the input voltage to the output capacitor for filtering when the transistor is off. Thus, Vo = Vin + Vin(ton/toff). Figure 31. Basic Boost Regulator The circuit of Figure 32 converts a 5V supply into a 15V supply with 150 mA of output current, a load regulation of 14 mV (30 mA to 140 mA), and a line regulation of 35 mV (4.5V ≤ Vin ≤ 8.5V). Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A Submit Documentation Feedback 17 LM2578A, LM3578A SNVS767E – AUGUST 2000 – REVISED APRIL 2013 www.ti.com Vin = 5V R4 = 200 kΩ Vo = 15V C1 = 1820 pF Vripple = 10 mV C2 = 470 μF Io = 140 mA C3 = 20 pF fosc = 50 kHz C4 = 0.0022 μF R1 = 140 kΩ L1 = 330 μH R2 = 10 kΩ D1 = 1N5818 R3 = 0.15Ω Figure 32. Boost or Step-Up Regulator R1 = (Vo − 1) R2 where R2 = 10 kΩ. R3 = V/(IL(max, DC) + 0.5 ΔIL) where: ΔIL = 2(ILOAD(min))(Vo/Vin) ΔIL is 200 mA in this example. R4, C3 and C4 are necessary for continuous operation and are typically 220 kΩ, 20 pF, and 0.0022 μF respectively. C1 is the timing capacitor found in Figure 14. C2 ≥ Io (Vo − Vin)/(fosc Vo Vripple). D1 is a Schottky type diode such as a 1N5818 or 1N5819. L1 is found as described in the buck converter section, using the inductance chart for Figure 29 for the boost configuration and 20% discontinuity. INVERTING REGULATOR Figure 33 shows the basic configuration for an inverting regulator. The input voltage is of a positive polarity, but the output is negative. The output may be less than, equal to, or greater in magnitude than the input. The relationship between the magnitude of the input voltage and the output voltage is Vo = Vin × (ton/toff). Figure 33. Basic Inverting Regulator Figure 34 shows an LM2578A configured as a 5V to −15V polarity inverter with an output current of 300 mA, a load regulation of 44 mV (60 mA to 300 mA) and a line regulation of 50 mV (4.5V ≤ Vin ≤ 8.5V). 18 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A LM2578A, LM3578A www.ti.com SNVS767E – AUGUST 2000 – REVISED APRIL 2013 R1 = (|Vo| +1) R2 where R2 = 10 kΩ. R3 = V/(IL(max, DC) + 0.5 ΔIL). R4 = 10VBE1Bf/(IL (max, DC) + 0.5 ΔIL) where: V, VBE1, Vsat, and Bf are defined in the Buck Converter with Boosted Output Current section. ΔIL = 2(ILOAD(min))(Vin +|Vo|)/VIN R5 is defined in the Buck Converter with Boosted Output Current section. R6 serves the same purpose as R4 in the Boost Regulator circuit and is typically 220 kΩ. C1, C3 and C4 are defined in the Boost Regulator section. C2 ≥ Io |Vo|/[fosc(|Vo| + Vin) Vripple] L1 is found as outlined in the section on buck converters, using the inductance chart of Figure 29 for the invert configuration and 20% discontinuity. Vin = 5V R4 = 190Ω Vo = −15V R5 = 82Ω Vripple = 5 mV R6 = 220 kΩ Io = 300 mA C1 = 1820 pF Imin = 60 mA C2 = 1000 μF fosc = 50 kHz C3 = 20 pF R1 = 160 kΩ C4 = 0.0022 μF R2 = 10 kΩ L1 = 150 μH R3 = 0.01Ω D1 = 1N5818 Figure 34. Inverting Regulator BUCK-BOOST REGULATOR The Buck-Boost Regulator, shown in Figure 35, may step a voltage up or down, depending upon whether or not the desired output voltage is greater or less than the input voltage. In this case, the output voltage is 12V with an input voltage from 9V to 15V. The circuit exhibits an efficiency of 75%, with a load regulation of 60 mV (10 mA to 100 mA) and a line regulation of 52 mV. R1 = (Vo − 1) R2 where R2 = 10 kΩ R3 = V/0. 75A R4, C1, C3 and C4 are defined in the Boost Regulator section. D1 and D2 are Schottky type diodes such as the 1N5818 or 1N5819. Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A Submit Documentation Feedback 19 LM2578A, LM3578A SNVS767E – AUGUST 2000 – REVISED APRIL 2013 www.ti.com where: Vd is the forward voltage drop of the diodes. Vsat is the saturation voltage of the LM2578A output transistor. Vsat1 is the saturation voltage of transistor Q1. L1 ≥ (Vin − Vsat − Vsat1) (ton/Ip) (1) where: RS-232 LINE DRIVER POWER SUPPLY The power supply, shown in Figure 36, operates from an input voltage as low as 4.2V (5V nominal), and delivers an output of ±12V at ±40 mA with better than 70% efficiency. The circuit provides a load regulation of ±150 mV (from 10% to 100% of full load) and a line regulation of ±10 mV. Other notable features include a cycle-by-cycle current limit and an output voltage ripple of less than 40 mVp-p. A unique feature of this circuit is its use of feedback from both outputs. This dual feedback configuration results in a sharing of the output voltage regulation by each output so that neither side becomes unbalanced as in single feedback systems. In addition, since both sides are regulated, it is not necessary to use a linear regulator for output regulation. The feedback resistors, R2 and R3, may be selected as follows by assuming a value of 10 kΩ for R1; R2 = (Vo − 1V)/45.8 μA = 240 kΩ R3 = (|Vo| +1V)/54.2 μA = 240 kΩ Actually, the currents used to program the values for the feedback resistors may vary from 40 μA to 60 μA, as long as their sum is equal to the 100 μA necessary to establish the 1V threshold across R1. Ideally, these currents should be equal (50 μA each) for optimal control. However, as was done here, they may be mismatched in order to use standard resistor values. This results in a slight mismatch of regulation between the two outputs. The current limit resistor, R4, is selected by dividing the current limit threshold voltage by the maximum peak current level in the output switch. For our purposes R4 = 110 mV/750 mA = 0.15Ω. A value of 0.1Ω was used. 20 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A LM2578A, LM3578A www.ti.com SNVS767E – AUGUST 2000 – REVISED APRIL 2013 9V ≤ Vin ≤ 15V R5 = 270 Vo = 12V C1 = 1820 pF Io = 100 mA C2 = 220 μF Vripple = 50 mV C3 = 20 pF fosc = 50 kHz C4 = 0.0022 μF R1 = 110k L1 = 220 μH R2 = 10k D1, D2 = 1N5819 R3 = 0.15 Q1 = D44 R4 = 220k Figure 35. Buck-Boost Regulator Vin = 5V R4 = 0.15Ω Vo ±12V C1 = 820 pF Io = ±40 mA C2 = 10 pF fosc = 80 kHz C3 = 220 μF R1 = 10 kΩ D1, D2, D3 = 1N5819 R2 = 240 kΩ T1 = PE-64287 R3 = 240 kΩ Figure 36. RS-232 Line Driver Power Supply Capacitor C1 sets the oscillator frequency and is selected from Figure 14. Capacitor C2 serves as a compensation capacitor for synchronous operation and a value of 10 to 50 pF should be sufficient for most applications. Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A Submit Documentation Feedback 21 LM2578A, LM3578A SNVS767E – AUGUST 2000 – REVISED APRIL 2013 www.ti.com A minimum value for an ideal output capacitor C3, could be calculated as C = Io × t/ΔV where Io is the load current, t is the transistor on time (typically 0.4/fosc), and ΔV is the peak-to-peak output voltage ripple. A larger output capacitor than this theoretical value should be used since electrolytics have poor high frequency performance. Experience has shown that a value from 5 to 10 times the calculated value should be used. For good efficiency, the diodes must have a low forward voltage drop and be fast switching. 1N5819 Schottky diodes work well. Transformer selection should be picked for an output transistor “on” time of 0.4/fosc, and a primary inductance high enough to prevent the output transistor switch from ramping higher than the transistor's rating of 750 mA. Pulse Engineering (San Diego, Calif.) and Renco Electronics, Inc. (Deer Park, N.Y.) can provide further assistance in selecting the proper transformer for a specific application need. The transformer used in Figure 36 was a Pulse Engineering PE-64287. 22 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A LM2578A, LM3578A www.ti.com SNVS767E – AUGUST 2000 – REVISED APRIL 2013 REVISION HISTORY Changes from Revision D (April 2013) to Revision E • Page Changed layout of National Data Sheet to TI format .......................................................................................................... 22 Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2578A LM3578A Submit Documentation Feedback 23 PACKAGE OPTION ADDENDUM www.ti.com 19-Mar-2015 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LM2578AM NRND SOIC D 8 95 TBD Call TI Call TI -40 to 125 2578 AM LM2578AM/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2578 AM LM2578AMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 2578 AM LM2578AN/NOPB ACTIVE PDIP P 8 40 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LM2578AN LM3578AM NRND SOIC D 8 95 TBD Call TI Call TI 0 to 125 3578 AM LM3578AM/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 125 3578 AM LM3578AMX NRND SOIC D 8 2500 TBD Call TI Call TI 0 to 125 3578 AM LM3578AMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 125 3578 AM LM3578AN/NOPB ACTIVE PDIP P 8 40 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 125 LM3578AN (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 19-Mar-2015 (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM2578AMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LM3578AMX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LM3578AMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM2578AMX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LM3578AMX SOIC D 8 2500 367.0 367.0 35.0 LM3578AMX/NOPB SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated