HT11G - HT18G 1.0 AMP. Glass Passivated High Efficient Rectifiers TS-1 Features Glass passivated chip junction. High efficiency, Low VF High current capability High reliability High surge current capability For use in low voltage, high frequency inventor, free wheeling, and polarity protection application. Mechanical Data Case: Molded plastic TS-1 Epoxy: UL 94V0 rate flame retardant Lead: Pure tin plated, lead free, solderable per MIL-STD-202, Method 208 guaranteed Polarity: Color band denotes cathode High temperature soldering guaranteed: 260 o C/10 seconds/.375”,(9.5mm) lead lengths at 5 lbs., (2.3kg) tension Mounting position: Any Weight: 0.20 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Symbol HT HT HT HT HT HT HT HT Units 11G 12G 13G 14G 15G 16G 17G 18G Maximum Recurrent Peak Reverse Voltage V RRM 50 100 200 300 400 600 800 1000 V Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375 (9.5mm) Lead Length @T A = 55 o C Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.0A Maximum DC Reverse Current o @T A =25 C at Rated DC Blocking Voltage @ T A =125 o C Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) V RMS V DC 35 50 70 100 140 200 210 300 280 400 420 600 560 800 700 1000 V V I(AV) 1.0 A IFSM 30 A VF 1.0 1.3 IR 1.7 V 5.0 150 Trr 50 Cj 15 uA uA 75 nS 10 pF o R θJA 95 TJ -65 to +150 o -65 to +150 Storage Temperature Range T STG 1. Reverse Recovery Test Conditions: IF =0.5A, IR =1.0A, IRR =0.25A Notes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Mount on cu-Pad Size 5mm x 5mm on PCB. o Typical Thermal Resistance Operating Temperature Range C/W C C Version: A06 RATINGS AND CHARACTERISTIC CURVES (HT11G THRU HT18G) FIG.2- TYPICAL REVERSE CHARACTERISTICS FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 1000 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375" (9.5mm) Lead Length 1.0 INSTANTANEOUS REVERSE CURRENT. ( A) AVERAGE FORWARD CURRENT. (A) 2.0 0 0 25 50 75 100 125 150 175 O AMBIENT TEMPERATURE. ( C) FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 100 Tj=125 0C 10 Tj=75 0C 1 Tj=25 0C PEAK FORWARD SURGE CURRENT. (A) 40 0.1 35 0 20 40 60 80 100 140 120 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 30 8.3ms Single Half Sine Wave JEDEC Method 25 20 FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 15 100 10 0 2 5 10 20 50 100 INSTANTANEOUS FORWARD CURRENT. (A) 1 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE.(pF) 70 60 50 40 30 HT 11G ~H 20 Tj=25 0C T1 5G HT16G 10 G 15 HT 1 0.1 HT11G-HT14G ~HT1 10 8G HT16G-HT18G 0 0.1 0.5 1 2 5 10 20 50 100 200 0.01 800 0 0.2 0.4 0.6 0.8 1.0 FORWARD VOLTAGE. (V) REVERSE VOLTAGE. (V) 1.2 1.4 FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (+) 50Vdc (approx) (-) (-) DUT NON INDUCTIVE PULSE GENERATOR (NOTE 2) OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: A06