TI CMPD2838E-NSA Lm5020 100v current mode pwm controller Datasheet

LM5020
www.ti.com
SNVS275F – MAY 2004 – REVISED APRIL 2006
LM5020 100V Current Mode PWM Controller
Check for Samples: LM5020
FEATURES
PACKAGES
•
•
•
•
•
•
•
•
1
2
•
•
•
•
•
•
Internal Start-up Bias Regulator
Error Amplifier
Precision Voltage Reference
Programmable Softstart
1A Peak Gate Driver
Maximum Duty Cycle Limiting (80% for
LM5020-1 or 50% for LM5020-2)
Programmable Line Under Voltage Lockout
(UVLO) with Adjustable Hysteresis
Cycle-by-Cycle Over-Current Protection
Slope Compensation (LM5020-1)
Programmable Oscillator Frequency with
Synchronization Capability
Current Sense Leading Edge Blanking
Thermal Shutdown Protection
DESCRIPTION
The LM5020 high voltage pulse-width-modulation
(PWM) controller contains all of the features needed
to implement single ended primary power converter
topologies. Output voltage regulation is based on
current-mode control, which eases the design of loop
compensation while providing inherent line feedforward. The LM5020 includes a high-voltage start-up
regulator that operates over a wide input range up to
100V. The PWM controller is designed for high speed
capability including an oscillator frequency range to
1MHz and total propagation delays less than 100ns.
Additional features include an error amplifier,
precision reference, line under-voltage lockout, cycleby-cycle current limit, slope compensation, softstart,
oscillator synchronization capability and thermal
shutdown. The controller is available in both VSSOP10 and WSON-10 packages.
APPLICATIONS
•
•
•
VSSOP-10
WSON-10 (4 mm x 4 mm)
Telecommunication Power Converters
Industrial Power Converters
+42V Automotive Systems
Typical Application Circuit
VIN
VIN
VOUT
VCC
LM5020
UVLO
SS
OUT
CS
RT/ SYNC
FB
GND
COMP
COMPENSATION
Figure 1. Non-Isolated Flyback Converter
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2006, Texas Instruments Incorporated
LM5020
SNVS275F – MAY 2004 – REVISED APRIL 2006
www.ti.com
Connection Diagram
Top View
1
10
2
9
3
8
4
7
5
6
VIN
FB
SS
RT/SYNC
CS
COMP
UVLO
VCC
OUT
GND
Figure 2. 10-Lead VSSOP, WSON
PIN DESCRIPTIONS
Pin
Name
Description
1
VIN
Source Input Voltage
Input to the start-up regulator. Input range is 13V to 100V.
Application Information
2
FB
Feedback Signal
Inverting input of the internal error amplifier. The noninverting input is internally connected to a 1.25V reference.
3
COMP
The output of the error amplifier and input to the
Pulse Width Modulator
COMP pull-up is provided by an internal 5K resistor which
may be used to bias an opto-coupler transistor.
4
VCC
Output of the internal high voltage series pass
regulator. Regulated output voltage is 7.7V
If an auxiliary winding raises the voltage on this pin above
the regulation set point, the internal series pass regulator
will shut down, reducing the internal power dissipation.
5
OUT
Output of the PWM controller
Gate driver output with a 1A peak current capability.
6
GND
Ground return
7
UVLO
Line Under-Voltage Shutdown
An external resistor divider from the power converter
source voltage sets the shutdown levels. The threshold at
this pin is 1.25V. Hysteresis is set by a switched internal
20µA current source.
8
CS
Current Sense input
Current sense input for current mode control and overcurrent protection. Current limiting is accomplished using a
dedicated current sense comparator. If the CS pin voltage
exceeds 0.5V the OUT pin switches low for cycle-by-cycle
current limiting. CS is held low for 50ns after OUT switches
high to blank leading edge current spikes.
9
RT / SYNC
Oscillator timing resistor pin and synchronization
input
An external resistor connected from RT to GND sets the
oscillator frequency. This pin also accepts synchronization
pulses from an external clock.
10
SS
Softstart Input
An external capacitor and an internal 10µA current source
set the soft-start ramp rate.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM5020
LM5020
www.ti.com
SNVS275F – MAY 2004 – REVISED APRIL 2006
Absolute Maximum Ratings (1) (2)
VIN to GND
-0.3V to 100V
VCC to GND
-0.3V to 16V
RT to GND
-0.3V to 5.5V
All other pins to GND
-0.3V to 7V
Power Dissipation
Internally Limited
ESD Rating (3)
Human Body Model
2kV
Storage Temperature
-65°C to +150°C
Junction Temperature
150°C
(1)
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is intended to be functional. For ensured specifications and test conditions, see the Electrical Characteristics.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
The human body model is a 100 pF capacitor discharged through a 1.5kΩ resistor.
(2)
(3)
Operating Ratings
VIN Voltage
13V to 90V
External Voltage applied to VCC
8V to 15V
Operating Junction Temperature
-40°C to +125°C
Electrical Characteristics
Specifications in standard type face are for TJ= +25°C and those in boldface type apply over the full operating junction
temperature range. Unless otherwise specified: VIN = 48V, VCC = 10V, and RT = 31.6kΩ. (1)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
7.4
7.7
8.0
V
Startup Regulator
VCCReg
VCC Regulation
VCC = Open
(2)
VCC Current Limit
See
I-VIN
Startup Regulator Leakage
VIN = 100V
15
150
22
500
mA
µA
IIN
Shutdown Current
VUVLO = 0V, VCC = open
250
350
µA
VCC Supply
ICC
VCC UVLO (Rising)
VccReg
- 300mV
VccReg 100mV
VCC UVLO (Falling)
5.3
6.0
6.7
V
2
3
mA
Supply Current
Cload = 0
V
Error Amplifier
GBW
Gain Bandwidth
4
DC Gain
MHz
75
Reference Voltage
FB = COMP
COMP Sink Capability
FB = 1.5V COMP= 1V
dB
1.225
1.25
1.275
5
17
V
1.225
1.25
1.275
V
16
20
24
µA
mA
UVLO Pin
Shutdown Threshold
Undervoltage Shutdown Hysteresis
Current Source
Current Limit
ILIM Delay to Output
CS step from 0 to 0.6V
Time to onset of OUT
Transition (90%)
Cycle by Cycle CS Threshold
Voltage
0.45
Leading Edge Blanking Time
(1)
(2)
30
0.5
ns
0.55
50
V
ns
Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control (SQC) methods. The limits are used to calculate National's Average Outgoing Quality Level (AOQL).
Device thermal limitations may limit usable range.
Submit Documentation Feedback
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM5020
3
LM5020
SNVS275F – MAY 2004 – REVISED APRIL 2006
www.ti.com
Electrical Characteristics (continued)
Specifications in standard type face are for TJ= +25°C and those in boldface type apply over the full operating junction
temperature range. Unless otherwise specified: VIN = 48V, VCC = 10V, and RT = 31.6kΩ.(1)
Symbol
Parameter
Conditions
Min
CS Sink Impedance (clocked)
Typ
Max
Units
35
55
Ω
Soft Start
Softstart Current Source
7
10
13
µA
Softstart to COMP Offset
0.35
0.55
0.75
V
Oscillator
Frequency1 (RT = 31.6k)
See (3)
175
200
225
kHz
Frequency2 (RT = 9.76k)
See (3)
560
630
700
kHz
2.4
3.2
3.8
V
Sync threshold
PWM Comparator
Delay to Output
COMP set to 2V,
CS stepped 0 to 0.4V,
Time to onset of OUT
transition low
Min Duty Cycle
COMP=0V
Max Duty Cycle (-1 Device)
25
75
Max Duty Cycle (-2 Device)
0
%
85
%
50
COMP to PWM Comparator Gain
%
0.33
COMP Open Circuit Voltage
COMP Short Circuit Current
80
ns
4.3
5.2
6.1
V
COMP=0V
0.6
1.1
1.5
mA
Delta increase at PWM
Comparator to CS
80
105
130
mV
Slope Compensation
Slope Comp Amplitude
(LM5020-1 Device Only)
Output Section
Output High Saturation
Iout = 50mA, VCC - VOUT
0.25
0.75
V
Output Low Saturation
IOUT = 100mA, VOUT
0.25
0.75
V
Rise Time
Cload = 1nF
18
ns
Fall Time
Cload = 1nF
15
ns
Thermal Shutdown Temp.
165
°C
Thermal Shutdown Hysteresis
25
°C
Thermal Shutdown
Tsd
(3)
4
Specification applies to the oscillator frequency. The operational frequency of the LM5020-2 devices is divided by two.
Submit Documentation Feedback
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM5020
LM5020
www.ti.com
SNVS275F – MAY 2004 – REVISED APRIL 2006
Typical Performance Characteristics
Unless otherwise specified: TJ = 25°C.
VCC and VIN
vs
VIN
20
VCC
vs
ICC (VIN = 48V)
9
18
8
16
7
6
12
VCC (V)
VCC (V)
14
10
8
5
4
6
3
4
2
2
0
1
0
20
10
0
5
10
VIN (V)
15
20
25
ICC (mA)
Figure 3.
Figure 4.
Oscillator Frequency
vs
RT
Oscillator Frequency
vs
Temperature
RT = 31.6kΩ
210
1.00E+06
FREQUENCY (kHz)
1.00E+05
200
195
190
1.00E+04
1
10
-40
100
RT (k:)
10
o
TEMPERATURE ( C)
Figure 5.
Figure 6.
Soft Start Current
vs
Temperature
Error Amp. Gain/Phase Plot
13.0
GAIN (dB)
CURRENT (PA)
11.8
10.6
9.4
8.2
50
225
40
180
30
135
20
90
10
45
0
0
-45
-10
-20
-90
-30
-135
-180
-40
7.0
-40
10
110
60
-50
10k
110
60
o
TEMPERATURE ( C)
PHASE (o)
FREQUENCY (Hz)
205
100k
1M
-225
10M
FREQUENCY (Hz)
Figure 7.
Figure 8.
Submit Documentation Feedback
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM5020
5
LM5020
SNVS275F – MAY 2004 – REVISED APRIL 2006
www.ti.com
Block Diagram
7.7V SERIES
REGULATOR
VCC
VIN
REFERENCE
ENABLE
5V
1.25V
UVLO
+
-
LOGIC
1.25V
UVLO
HYSTERESIS
(20 PA)
RT/SYNC
CLK
OSC
VCC
DRIVER
SLOPECOMP
RAMP
GENERATOR
(LM5020-1 Only)
OUT
50 PA
Max Duty Limit
LM5020-1 (80%)
LM5020-2 (50%)
0
S
Q
R
Q
5V
COMP
5k
2R
1.25V
FB
GND
PWM
+
-
LOGIC
1.4V
R
SS
SS
CS
0.5V
2k
+
-
10 PA
SS
CLK + LEB
6
Submit Documentation Feedback
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM5020
LM5020
www.ti.com
SNVS275F – MAY 2004 – REVISED APRIL 2006
DETAILED OPERATING DESCRIPTION
The LM5020 High Voltage PWM controller contains all of the features needed to implement single ended primary
power converter topologies. The LM5020 includes a high-voltage startup regulator that operates over a wide
input range to 100V. The PWM controller is designed for high speed capability including an oscillator frequency
range to 1MHz and total propagation delays less than 100ns. Additional features include an error amplifier,
precision reference, line under-voltage lockout, cycle-by-cycle current limit, slope compensation, softstart,
oscillator sync capability and thermal shutdown. The functional block diagram of the LM5020 is shown in Figure
1. The LM5020 is designed for current-mode control power converters, which require a single drive output, such
as Flyback and Forward topologies. The LM5020 provides all of the advantages of current-mode control
including line feed-forward, cycle-by-cycle current limiting and simplified loop compensation .
High Voltage Start-Up Regulator
The LM5020 contains an internal high voltage startup regulator, that allows the input pin (Vin) to be connected
directly to line voltages as high as 100V. The regulator output is internally current limited to 15mA. When power
is applied, the regulator is enabled and sources current into an external capacitor connected to the VCC pin. The
recommended capacitance range for the Vcc regulator is 0.1µF to 100µF. When the voltage on the VCC pin
reaches the regulation level of 7.7V, the controller output is enabled. The controller will remain enabled until VCC
falls below 6V.
In typical applications, a transformer auxiliary winding is connected through a diode to the VCC pin. This winding
should raise the VCC voltage above 8V to shut off the internal startup regulator. Powering VCC from an auxiliary
winding improves conversion efficiency while reducing the power dissipated in the controller. The external VCC
capacitor must be selected such that the capacitor maintains the Vcc voltage greater than the VCC UVLO falling
threshold (6V) during the initial start-up. During a fault condition when the converter auxiliary winding is inactive,
external current draw on the VCC line should be limited such that the power dissipated in the start-up regulator
does not exceed the maximum power dissipation capability of the controller.
An external start-up or other bias rail can be used instead of the internal start-up regulator by connecting the VCC
and the Vin pins together and feeding the external bias voltage (8-15V) to the two pins.
Line Under Voltage Detector
The LM5020 contains a line Under Voltage Lock Out (UVLO) circuit. An external set-point voltage divider from
Vin to GND sets the operational range of the converter. The resistor divider must be designed such that the
voltage at the UVLO pin is greater than 1.25V when Vin is in the desired operating range. If the under voltage
threshold is not met, all functions of the controller are disabled and the controller remains in a low power standby
state.
UVLO hysteresis is accomplished with an internal 20µA current source that is switched on or off into the
impedance of the set-point divider. When the UVLO threshold is exceeded, the current source is activated to
instantly raise the voltage at the UVLO pin. When the UVLO pin voltage falls below the 1.25V threshold the
current source is turned off, causing the voltage at the UVLO pin to fall. The UVLO pin can also be used to
implement a remote enable / disable function. If an external transistor pulls the UVLO pin below the 1.25V
threshold, the converter is disabled.
Error Amplifier
An internal high gain error amplifier is provided within the LM5020. The amplifier's non-inverting input is internally
set to a fixed reference voltage of 1.25V. The inverting input is connected to the FB pin. In non-isolated
applications, the power converter output is connected to the FB pin via voltage scaling resistors. Loop
compensation components are connected between the COMP and FB pins. For most isolated applications the
error amplifier function is implemented on the secondary side of the converter and the internal error amplifier is
not used. The internal error amplifier is configured as an open drain output and can be disabled by connecting
the FB pin to ground. An internal 5K pull-up resistor between a 5V reference and COMP can be used as the pullup for an optocoupler in isolated applications.
Submit Documentation Feedback
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM5020
7
LM5020
SNVS275F – MAY 2004 – REVISED APRIL 2006
www.ti.com
Current Limit/Current Sense
The LM5020 provides a cycle-by-cycle over current protection function. Current limit is accomplished by an
internal current sense comparator. If the voltage at the current sense comparator input exceeds 0.5V, the output
is immediately terminated. A small RC filter, located near the controller, is recommended to filter noise from the
current sense signal. The CS input has an internal MOSFET which discharges the CS pin capacitance at the
conclusion of every cycle. The discharge device remains on an additional 50ns after the beginning of the new
cycle to attenuate the leading edge spike on the current sense signal.
The LM5020 current sense and PWM comparators are very fast, and may respond to short duration noise
pulses. Layout considerations are critical for the current sense filter and sense resistor. The capacitor associated
with the CS filter must be located very close to the LM5020 and connected directly to the pins of the controller
(CS and GND). If a current sense transformer is used, both leads of the transformer secondary should be routed
to the sense resistor and the current sense filter network. A sense resistor located in the source of the primary
power MOSFET may be used for current sensing, but a low inductance resistor is required. When designing with
a current sense resistor all of the noise sensitive low power ground connections should be connected together
local to the controller and a single connection should be made to the high current power ground (sense resistor
ground point).
Oscillator and Sync Capability
A single external resistor connected between the RT and GND pins sets the LM5020 oscillator frequency.
Internal to the LM5020-2 device (50% duty cycle limited option) is an oscillator divide by two circuit. This divide
by two circuit creates an exact 50% duty cycle pulse which is used internally to create a precise 50% duty cycle
limit function. Because of this, the internal oscillator actually operates at twice the frequency of the output (OUT).
For the LM5020-1 device the oscillator frequency and the operational output frequency are the same. To set a
desired output operational frequency (F), the RT resistor can be calculated from:
LM5020-1:
1
RT =
F x 158 x 10-12
(1)
LM5020-2:
RT =
1
F x 316 x 10-12
(2)
The LM5020 can also be synchronized to an external clock. The external clock must have a higher frequency
than the free running oscillator frequency set by the RT resistor. The clock signal should be capacitively coupled
into the RT pin through a 100pF capacitor. A peak voltage level greater than 3.7 Volts at the RT pin is required
for detection of the sync pulse. The sync pulse width should be set between 15 to 150ns by the external
components. The RT resistor is always required, whether the oscillator is free running or externally synchronized.
The voltage at the RT pin is internally regulated at 2 Volts. The RT resistor should be located very close to the
device and connected directly to the pins of the controller (RT and GND).
PWM Comparator / Slope Compensation
The PWM comparator compares the current ramp signal with the loop error voltage derived from the error
amplifier output. The error amplifier output voltage at the COMP pin is offset by 1.4V and then further attenuated
by a 3:1 resistor divider. The PWM comparator polarity is such that 0 Volts on the COMP pin will result in a zero
duty cycle at the controller output. For duty cycles greater than 50 percent, current mode control circuits are
subject to sub-harmonic oscillation. By adding an additional fixed slope voltage ramp signal (slope compensation)
to the current sense signal, this oscillation can be avoided. The LM5020-1 integrates this slope compensation by
summing a current ramp generated by the oscillator with the current sense signal. Additional slope compensation
may be added by increasing the source impedance of the current sense signal. Since the LM5020-2 is not
capable of duty cycles greater than 50%, there is no slope compensation feature in this device.
8
Submit Documentation Feedback
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM5020
LM5020
www.ti.com
SNVS275F – MAY 2004 – REVISED APRIL 2006
Soft Start
The softstart feature allows the power converter to gradually reach the initial steady state operating point, thereby
reducing start-up stresses and current surges. At power on, after the VCC and the line undervoltage lockout
thresholds are satisfied, an internal 10µA current source charges an external capacitor connected to the SS pin.
The capacitor voltage will ramp up slowly and will limit the COMP pin voltage and the duty cycle of the output
pulses.
Gate Driver and Maximum Duty Cycle Limit
The LM5020 provides an internal gate driver (OUT), which can source and sink a peak current of 1 Amp. The
LM5020 is available in two duty cycle limit options. The maximum output duty cycle is typically 80% for the
LM5020-1 option and precisely equal to 50% for the LM5020-2 option. The maximum duty cycle function for the
LM5020-2 is accomplished with an internal toggle flip-flop which ensures an accurate duty cycle limit. The
internal oscillator frequency of the LM5020-2 is therefore twice the operating frequency of the PWM controller
(OUT pin).
The 80% maximum duty cycle limit of the LM5020-1 is determined by the internal oscillator and varies more than
the 50% limit of the LM5020-2. For the LM5020-1 the internal oscillator frequency and the operational frequency
of the PWM controller are equal.
Thermal Protection
Internal thermal shutdown circuitry is provided to protect the integrated circuit in the event the maximum junction
temperature is exceeded. This feature prevents catastrophic failures from accidental device overheating. When
activated, typically at 165 degrees Celsius, the controller is forced into a low power standby state, disabling the
output driver and the bias regulator. After the temperature is reduced (typical hysteresis = 25°C) the VCC
regulator is enabled and a softstart sequence initiated.
Typical Application Circuit: 36V - 75 VIN and 3.3V, 4.5A OUT
C9
R10
R13
T1
V+
J1
30-75V IN
1
J2
+3.3V
2
C12
470 pF
D2
CMPD2838E
20
0.1 PF
10, 1W
1
C13
100 PF
GND
D3
MBRD835L
2
GND
C4
0.1 PF
Shutdown
R3
2.87k
GND
C10
4.7 PF
1
7
GND
VIN
VCC
UVLO
OUT
C6
220 pF
R5
15.0k
Z1
1SMB5936B
COMP
CS
FB
9 RT/
10 SYNC
GND
SS
C8
100 pF
R6
12.4k
GND
Q1
Si7898DP
R11
2.43k
4
5
R12
1.47k
R7
8
2
100
6
R8
0.47
R9
0.47
GND
C11
1000 pF
LM5020
C5
0.01 PF
C7
3300 pF
D1
CMPD2838E
GND GND
U1
R4
1.00k
3
SYNC
Input
GND
GND
GND
C3
0.01 PF
GND
5
6
7
8
GND
C2
2.2 PF
R1
10
OUT RTN
4
3
2
1
C1
2.2 PF
GND
R2
61.9k
C15
270 PF
GND
GND
GND
C14
100 PF
GND
GND
GND
GND
Submit Documentation Feedback
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM5020
9
LM5020
SNVS275F – MAY 2004 – REVISED APRIL 2006
www.ti.com
Table 1. Bill Of Materials
ITEM
10
PART NUMBER
DESCRIPTION
VALUE
C
1
C4532X7R2A225M
CAPACITOR, CER, TDK
2.2µF, 100V
C
2
C4532X7R2A225M
CAPACITOR, CER, TDK
2.2µF, 100V
C
3
C2012X7R1H103K
CAPACITOR, CER, TDK
0.01µF, 50V
C
4
C3216X7R2A104K
CAPACITOR, CER, TDK
0.1µF, 100V
C
5
C2012X7R1H103K
CAPACITOR, CER, TDK
0.01µF, 50V
C
6
C2012C0G1H221J
CAPACITOR, CER, KEMET
220pF, 50V
C
7
C2012C0G1H332J
CAPACITOR, CER, TDK
3300pF, 50V
C
8
C2012C0G1H101J
CAPACITOR, CER, TDK
100pF, 50V
C
9
C2012X7R1H104K
CAPACITOR, CER, TDK
0.1µF, 50V
C
10
C3216X7R1C475K
CAPACITOR, CER, TDK
4.7µF, 16V
C
11
C2012C0G1H102J
CAPACITOR, CER, TDK
1000pF, 50V
C
12
C2012C0G1H471J
CAPACITOR, CER, TDK
470p, 50V
C
13
C4532X7S0G107M
CAPACITOR, CER, TDK
100µF, 4V
C
14
C4532X7S0G107M
CAPACITOR, CER, TDK
100µF, 4V
C
15
A700X277M0004AT
CAPACITOR, ALUM ORGANIC, KEMET
270µF, 4V
D
1
CMPD2838E-NSA
DIODE, SIGNAL, CENTRAL
D
2
CMPD2838E-NSA
DIODE, SIGNAL, CENTRAL
D
3
MBRD835L
DIODE, RECTIFIER, ON
SEMICONDUCTOR
J
1
MKDS 1/2-3.81
TERM BLK, MINI, 2 POS, PHOENIX
CONTACT
J
2
MKDS 1/2-3.81
TERM BLK, MINI, 2 POS, PHOENIX
CONTACT
Q
1
SI7898DP
FET, SILICONIX
150V, 85mΩ
R
1
CRCW120610R0F
RESISTOR
10
R
2
CRCW12066192F
RESISTOR
61.9kΩ
R
3
CRCW08052871F
RESISTOR
2.87kΩ
R
4
CRCW08051001F
RESISTOR
1.00kΩ
R
5
CRCW08051502F
RESISTOR
15.0kΩ
R
6
CRCW08051242F
RESISTOR
12.4kΩ
R
7
CRCW08051000F
RESISTOR
100
R
8
CRCW12060R47F
RESISTOR
0.47
R
9
CRCW12060R47F
RESISTOR
0.47
R
10
CRCW251210R0F
RESISTOR
10, 1W
R
11
CRCW08052431F
RESISTOR
2.43K
R
12
CRCW08051471F
RESISTOR
1.47K
R
13
CRCW080520R0F
RESISTOR
20
T
1
B0695-A COILCRAFT
TRANSFORMER, FLYBACK, EFD20 CORE
T
1
PA0751 PULSE
TRANSFORMER, FLYBACK, EFD20 CORE
U
1
LM5020-2MM
CONTROLLER, SINGLE OUT, PWM,
NATIONAL
Z
1
1SMB5936B
DIODE, ZENER, SMB, 30V
Submit Documentation Feedback
ALTERNATE
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM5020
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
LM5020MM-1
ACTIVE
VSSOP
DGS
10
1000
TBD
Call TI
Call TI
-40 to 125
SBLB
LM5020MM-1/NOPB
ACTIVE
VSSOP
DGS
10
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
SBLB
LM5020MM-2
ACTIVE
VSSOP
DGS
10
1000
TBD
Call TI
Call TI
-40 to 125
SBNB
LM5020MM-2/NOPB
ACTIVE
VSSOP
DGS
10
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
SBNB
LM5020MMX-1
ACTIVE
VSSOP
DGS
10
3500
TBD
Call TI
Call TI
-40 to 125
SBLB
LM5020MMX-1/NOPB
ACTIVE
VSSOP
DGS
10
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
SBLB
LM5020MMX-2
ACTIVE
VSSOP
DGS
10
3500
TBD
Call TI
Call TI
-40 to 125
SBNB
LM5020MMX-2/NOPB
ACTIVE
VSSOP
DGS
10
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
SBNB
LM5020SD-1
ACTIVE
WSON
DPR
10
1000
TBD
Call TI
Call TI
-40 to 125
5020-1
LM5020SD-1/NOPB
ACTIVE
WSON
DPR
10
1000
Green (RoHS
& no Sb/Br)
SN
Level-1-260C-UNLIM
-40 to 125
5020-1
LM5020SD-2/NOPB
ACTIVE
WSON
DPR
10
1000
Green (RoHS
& no Sb/Br)
SN
Level-1-260C-UNLIM
-40 to 125
5020-2
LM5020SDX-1
ACTIVE
WSON
DPR
10
4500
TBD
Call TI
Call TI
-40 to 125
5020-1
LM5020SDX-1/NOPB
ACTIVE
WSON
DPR
10
4500
Green (RoHS
& no Sb/Br)
SN
Level-1-260C-UNLIM
-40 to 125
5020-1
LM5020SDX-2
ACTIVE
WSON
DPR
10
4500
TBD
Call TI
Call TI
-40 to 125
5020-2
LM5020SDX-2/NOPB
ACTIVE
WSON
DPR
10
4500
Green (RoHS
& no Sb/Br)
SN
Level-1-260C-UNLIM
-40 to 125
5020-2
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
21-Mar-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM5020MM-1
VSSOP
DGS
10
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5020MM-1/NOPB
VSSOP
DGS
10
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5020MM-2
VSSOP
DGS
10
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5020MM-2/NOPB
VSSOP
DGS
10
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5020MMX-1
VSSOP
DGS
10
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5020MMX-1/NOPB
VSSOP
DGS
10
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5020MMX-2
VSSOP
DGS
10
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5020MMX-2/NOPB
VSSOP
DGS
10
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM5020SD-1
WSON
DPR
10
1000
178.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
LM5020SD-1/NOPB
WSON
DPR
10
1000
178.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
LM5020SD-2/NOPB
WSON
DPR
10
1000
178.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
LM5020SDX-1
WSON
DPR
10
4500
330.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
LM5020SDX-1/NOPB
WSON
DPR
10
4500
330.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
LM5020SDX-2
WSON
DPR
10
4500
330.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
LM5020SDX-2/NOPB
WSON
DPR
10
4500
330.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
21-Mar-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM5020MM-1
VSSOP
DGS
10
1000
203.0
190.0
41.0
LM5020MM-1/NOPB
VSSOP
DGS
10
1000
203.0
190.0
41.0
LM5020MM-2
VSSOP
DGS
10
1000
203.0
190.0
41.0
LM5020MM-2/NOPB
VSSOP
DGS
10
1000
203.0
190.0
41.0
LM5020MMX-1
VSSOP
DGS
10
3500
367.0
367.0
35.0
LM5020MMX-1/NOPB
VSSOP
DGS
10
3500
367.0
367.0
35.0
LM5020MMX-2
VSSOP
DGS
10
3500
367.0
367.0
35.0
LM5020MMX-2/NOPB
VSSOP
DGS
10
3500
367.0
367.0
35.0
LM5020SD-1
WSON
DPR
10
1000
203.0
190.0
41.0
LM5020SD-1/NOPB
WSON
DPR
10
1000
203.0
190.0
41.0
LM5020SD-2/NOPB
WSON
DPR
10
1000
203.0
190.0
41.0
LM5020SDX-1
WSON
DPR
10
4500
367.0
367.0
35.0
LM5020SDX-1/NOPB
WSON
DPR
10
4500
367.0
367.0
35.0
LM5020SDX-2
WSON
DPR
10
4500
367.0
367.0
35.0
LM5020SDX-2/NOPB
WSON
DPR
10
4500
367.0
367.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
DPR0010A
SDC10A (Rev A)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Similar pages