ATMEL AT28C64B 64k (8k x 8) parallel eeprom with page write and software data protection Datasheet

Features
• Fast Read Access Time – 150 ns
• Automatic Page Write Operation
– Internal Address and Data Latches for 64 Bytes
• Fast Write Cycle Times
•
•
•
•
•
•
•
•
•
– Page Write Cycle Time: 10 ms Maximum (Standard)
2 ms Maximum (Option – Ref. AT28HC64BF Datasheet)
– 1 to 64-byte Page Write Operation
Low Power Dissipation
– 40 mA Active Current
– 100 µA CMOS Standby Current
Hardware and Software Data Protection
DATA Polling and Toggle Bit for End of Write Detection
High Reliability CMOS Technology
– Endurance: 100,000 Cycles
– Data Retention: 10 Years
Single 5V ±10% Supply
CMOS and TTL Compatible Inputs and Outputs
JEDEC Approved Byte-wide Pinout
Industrial Temperature Ranges
Green (Pb/Halide-free) Packaging Option
1. Description
64K (8K x 8)
Parallel
EEPROM with
Page Write and
Software Data
Protection
AT28C64B
The AT28C64B is a high-performance electrically-erasable and programmable readonly memory (EEPROM). Its 64K of memory is organized as 8,192 words by 8 bits.
Manufactured with Atmel’s advanced nonvolatile CMOS technology, the device offers
access times to 150 ns with power dissipation of just 220 mW. When the device is
deselected, the CMOS standby current is less than 100 µA.
The AT28C64B is accessed like a Static RAM for the read or write cycle without the
need for external components. The device contains a 64-byte page register to allow
writing of up to 64 bytes simultaneously. During a write cycle, the addresses and 1 to
64 bytes of data are internally latched, freeing the address and data bus for other
operations. Following the initiation of a write cycle, the device will automatically write
the latched data using an internal control timer. The end of a write cycle can be
detected by DATA POLLING of I/O7. Once the end of a write cycle has been
detected, a new access for a read or write can begin.
Atmel’s AT28C64B has additional features to ensure high quality and manufacturability. The device utilizes internal error correction for extended endurance and improved
data retention characteristics. An optional software data protection mechanism is
available to guard against inadvertent writes. The device also includes an extra
64 bytes of EEPROM for device identification or tracking.
0270K–PEEPR–10/06
2. Pin Configurations
2.2
Function
A0 - A12
Addresses
CE
Chip Enable
OE
Output Enable
WE
Write Enable
I/O0 - I/O7
Data Inputs/Outputs
NC
No Connect
DC
Don’t Connect
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
5
6
7
8
9
10
11
12
13
A8
A9
A11
NC
OE
A10
CE
I/O7
I/O6
I/O1
I/O2
GND
DC
I/O3
I/O4
I/O5
A6
A5
A4
A3
A2
A1
A0
NC
I/O0
4
3
2
1
32
31
30
A7
A12
NC
DC
VCC
WE
NC
Pin Name
32-lead PLCC Top View
2.1
28-lead PDIP, 28-lead SOIC Top View
NC
A12
A7
A6
A5
A4
A3
A2
A1
A0
I/O0
I/O1
I/O2
GND
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
VCC
WE
NC
A8
A9
A11
OE
A10
CE
I/O7
I/O6
I/O5
I/O4
I/O3
Note:
PLCC package pins 1 and 17 are Don’t Connect.
2.3
28-lead TSOP Top View
OE
A11
A9
A8
NC
WE
VCC
NC
A12
A7
A6
A5
A4
A3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
A10
CE
I/O7
I/O6
I/O5
I/O4
I/O3
GND
I/O2
I/O1
I/O0
A0
A1
A2
AT28C64B
0270K–PEEPR–10/06
AT28C64B
3. Block Diagram
DATA INPUTS/OUTPUTS
I/O0 - I/O7
VCC
GND
OE
WE
OE, CE and WE
LOGIC
CE
Y DECODER
ADDRESS
INPUTS
DATA LATCH
INPUT/OUTPUT
BUFFERS
Y-GATING
CELL MATRIX
X DECODER
IDENTIFICATION
4. Device Operation
4.1
Read
The AT28C64B is accessed like a Static RAM. When CE and OE are low and WE is high, the
data stored at the memory location determined by the address pins is asserted on the outputs.
The outputs are put in the high-impedance state when either CE or OE is high. This dual line
control gives designers flexibility in preventing bus contention in their systems.
4.2
Byte Write
A low pulse on the WE or CE input with CE or WE low (respectively) and OE high initiates a
write cycle. The address is latched on the falling edge of CE or WE, whichever occurs last.
The data is latched by the first rising edge of CE or WE. Once a byte write has been started, it
will automatically time itself to completion. Once a programming operation has been initiated
and for the duration of tWC, a read operation will effectively be a polling operation.
4.3
Page Write
The page write operation of the AT28C64B allows 1 to 64 bytes of data to be written into the
device during a single internal programming period. A page write operation is initiated in the
same manner as a byte write; after the first byte is written, it can then be followed by 1 to 63
additional bytes. Each successive byte must be loaded within 150 µs (tBLC) of the previous
byte. If the tBLC limit is exceeded, the AT28C64B will cease accepting data and commence the
internal programming operation. All bytes during a page write operation must reside on the
same page as defined by the state of the A6 to A12 inputs. For each WE high to low transition
during the page write operation, A6 to A12 must be the same.
The A0 to A5 inputs specify which bytes within the page are to be written. The bytes may be
loaded in any order and may be altered within the same load period. Only bytes which are
specified for writing will be written; unnecessary cycling of other bytes within the page does
not occur.
3
0270K–PEEPR–10/06
4.4
DATA Polling
The AT28C64B features DATA Polling to indicate the end of a write cycle. During a byte or
page write cycle an attempted read of the last byte written will result in the complement of the
written data to be presented on I/O7. Once the write cycle has been completed, true data is
valid on all outputs, and the next write cycle may begin. DATA Polling may begin at any time
during the write cycle.
4.5
Toggle Bit
In addition to DATA Polling, the AT28C64B provides another method for determining the end of
a write cycle. During the write operation, successive attempts to read data from the device will
result in I/O6 toggling between one and zero. Once the write has completed, I/O6 will stop toggling, and valid data will be read. Toggle bit reading may begin at any time during the write
cycle.
4.6
Data Protection
If precautions are not taken, inadvertent writes may occur during transitions of the host system
power supply. Atmel® has incorporated both hardware and software features that will protect
the memory against inadvertent writes.
4.6.1
Hardware Data Protection
Hardware features protect against inadvertent writes to the AT28C64B in the following ways:
(a) VCC sense – if VCC is below 3.8 V (typical), the write function is inhibited; (b) VCC power-on
delay – once VCC has reached 3.8 V, the device will automatically time out 5 ms (typical)
before allowing a write; (c) write inhibit – holding any one of OE low, CE high, or WE high
inhibits write cycles; and (d) noise filter – pulses of less than 15 ns (typical) on the WE or CE
inputs will not initiate a write cycle.
4.6.2
Software Data Protection
A software controlled data protection feature has been implemented on the AT28C64B. When
enabled, the software data protection (SDP), will prevent inadvertent writes. The SDP feature
may be enabled or disabled by the user; the AT28C64B is shipped from Atmel with SDP disabled.
SDP is enabled by the user issuing a series of three write commands in which three specific
bytes of data are written to three specific addresses (see “Software Data Protection Algorithms” on page 10). After writing the 3-byte command sequence and waiting tWC, the entire
AT28C64B will be protected against inadvertent writes. It should be noted that even after SDP
is enabled, the user may still perform a byte or page write to the AT28C64B by preceding the
data to be written by the same 3-byte command sequence used to enable SDP.
Once set, SDP remains active unless the disable command sequence is issued. Power transitions do not disable SDP, and SDP protects the AT28C64B during power-up and power-down
conditions. All command sequences must conform to the page write timing specifications. The
data in the enable and disable command sequences is not actually written into the device;
their addresses may still be written with user data in either a byte or page write operation.
After setting SDP, any attempt to write to the device without the 3-byte command sequence
will start the internal write timers. No data will be written to the device. However, for the duration of tWC, read operations will effectively be polling operations.
4.7
Device Identification
An extra 64 bytes of EEPROM memory are available to the user for device identification. By
raising A9 to 12V ±0.5V and using address locations 1FC0H to 1FFFH, the additional bytes
may be written to or read from in the same manner as the regular memory array.
4
AT28C64B
0270K–PEEPR–10/06
AT28C64B
5. DC and AC Operating Range
AT28C64B-15
Operating Temperature (Case)
-40°C - 85°C
5V ±10%
VCC Power Supply
6. Operating Modes
Mode
CE
OE
WE
I/O
Read
VIL
VIL
VIH
DOUT
VIL
VIH
VIL
DIN
X
High Z
Write
(2)
Standby/Write Inhibit
(1)
VIH
X
Write Inhibit
X
X
VIH
Write Inhibit
X
VIL
X
Output Disable
X
VIH
X
High Z
VIL
High Z
Chip Erase
Notes:
VIL
VH
(3)
1. X can be VIL or VIH.
2. See “AC Write Waveforms” on page 8.
3. VH = 12.0V ±0.5V.
7. Absolute Maximum Ratings*
Temperature Under Bias................................ -55°C to +125°C
*NOTICE:
Storage Temperature ..................................... -65°C to +150°C
All Input Voltages
(including NC Pins)
with Respect to Ground ...................................-0.6V to +6.25V
All Output Voltages
with Respect to Ground .............................-0.6V to VCC + 0.6V
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability
Voltage on OE and A9
with Respect to Ground ...................................-0.6V to +13.5V
8. DC Characteristics
Symbol
Parameter
Condition
ILI
Input Load Current
VIN = 0V to VCC + 1V
ILO
Output Leakage Current
ISB1
VCC Standby Current CMOS
ISB2
VCC Standby Current TTL
ICC
VCC Active Current
VIL
Input Low Voltage
VIH
Input High Voltage
VOL
Output Low Voltage
IOL = 2.1 mA
VOH
Output High Voltage
IOH = -400 µA
Min
Max
Units
10
µA
VI/O = 0V to VCC
10
µA
CE = VCC - 0.3V to VCC + 1V
100
µA
CE = 2.0V to VCC + 1V
2
mA
f = 5 MHz; IOUT = 0 mA
40
mA
0.8
2.0
0.40
2.4
V
V
V
V
5
0270K–PEEPR–10/06
9. AC Read Characteristics
AT28C64B-15
Symbol
Parameter
tACC
Min
Max
Units
Address to Output Delay
150
ns
(1)
CE to Output Delay
150
ns
tOE(2)
OE to Output Delay
0
70
ns
tDF(3)(4)
CE or OE to Output Float
0
50
ns
tOH
Output Hold from OE, CE or Address, whichever
occurred first
0
tCE
ns
10. AC Read Waveforms(1)(2)(3)(4)
ADDRESS
ADDRESS VALID
CE
tCE
tOE
OE
tOH
tDF
tACC
OUTPUT
Notes:
HIGH Z
OUTPUT VALID
1. CE may be delayed up to tACC - tCE after the address transition without impact on tACC.
2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE or by tACC - tOE after an address change
without impact on tACC.
3. tDF is specified from OE or CE whichever occurs first (CL = 5 pF).
4. This parameter is characterized and is not 100% tested.
6
AT28C64B
0270K–PEEPR–10/06
AT28C64B
11. Input Test Waveforms and Measurement Level
tR, tF < 5 ns
12. Output Test Load
13. Pin Capacitance
f = 1 MHz, T = 25°C(1)
Symbol
CIN
COUT
Note:
Typ
Max
Units
Conditions
4
6
pF
VIN = 0V
8
12
pF
VOUT = 0V
1. This parameter is characterized and is not 100% tested.
7
0270K–PEEPR–10/06
14. AC Write Characteristics
Symbol
Parameter
Min
Max
Units
tAS, tOES
Address, OE Setup Time
0
ns
tAH
Address Hold Time
50
ns
tCS
Chip Select Setup Time
0
ns
tCH
Chip Select Hold Time
0
ns
tWP
Write Pulse Width (WE or CE)
100
ns
tDS
Data Setup Time
50
ns
tDH, tOEH
Data, OE Hold Time
0
ns
15. AC Write Waveforms
15.1
WE Controlled
OE
tOES
tOEH
ADDRESS
tAS
CE
tCH
tAH
tCS
WE
tWP
tDS
tDH
DATA IN
15.2
CE Controlled
OE
tOES
tOEH
ADDRESS
tAS
tCH
tAH
WE
tCS
CE
tWP
tDS
tDH
DATA IN
8
AT28C64B
0270K–PEEPR–10/06
AT28C64B
16. Page Mode Characteristics
Symbol
Parameter
tWC
Min
Max
Units
Write Cycle Time
10
ms
tWC
Write Cycle Time (option available – Ref. AT28HC64BF datasheet)
2
ms
tAS
Address Setup Time
0
ns
tAH
Address Hold Time
50
ns
tDS
Data Setup Time
50
ns
tDH
Data Hold Time
0
ns
tWP
Write Pulse Width
100
ns
tBLC
Byte Load Cycle Time
tWPH
Write Pulse Width High
150
50
µs
ns
17. Page Mode Write Waveforms(1)(2)
OE
CE
WE
tAS
tDH
tAH
A0 -A12
tBLC
tWPH
tWP
VALID ADD
tDS
DATA
VALID DATA
tWC
Notes:
1. A6 through A12 must specify the same page address during each high to low transition of WE (or CE).
2. OE must be high only when WE and CE are both low.
18. Chip Erase Waveforms
tS
tH
tW
tS = tH = 1 µs (min.)
tW = 10 ms (min.)
VH = 12.0V ±0.5V
9
0270K–PEEPR–10/06
19. Software Data Protection Enable
Algorithm(1)
20. Software Data Protection Disable
Algorithm(1)
LOAD DATA AA
TO
ADDRESS 1555
LOAD DATA AA
TO
ADDRESS 1555
LOAD DATA 55
TO
ADDRESS 0AAA
LOAD DATA A0
TO
ADDRESS 1555
LOAD DATA 55
TO
ADDRESS 0AAA
WRITES
LOAD DATA 80
TO
ADDRESS 1555
ENABLED(2)
LOAD DATA XX
TO
ANY ADDRESS(4)
LOAD LAST BYTE
TO
LAST ADDRESS
LOAD DATA AA
TO
ADDRESS 1555
LOAD DATA 55
TO
ADDRESS 0AAA
ENTER DATA
PROTECT STATE
LOAD DATA 20
TO
ADDRESS 1555
Notes:
1. Data Format: I/O7 - I/O0 (Hex);
Address Format: A12 - A0 (Hex).
EXIT DATA
PROTECT STATE(3)
LOAD DATA XX
TO
ANY ADDRESS(4)
2. Write Protect state will be activated at end of write
even if no other data is loaded.
LOAD LAST BYTE
TO
LAST ADDRESS
3. Write Protect state will be deactivated at end of write
period even if no other data is loaded.
4. 1 to 64 bytes of data are loaded.
Notes:
1. Data Format: I/O7 - I/O0 (Hex);
Address Format: A12 - A0 (Hex).
2. Write Protect state will be activated at end of write
even if no other data is loaded.
3. Write Protect state will be deactivated at end of write
period even if no other data is loaded.
4. 1 to 64 bytes of data are loaded.
21. Software Protected Write Cycle Waveforms(1)(2)
OE
CE
tWPH
tWP
WE
tAS
tAH
tBLC
tDH
A0 -A5
A6 - A12
tDS
DATA
tWC
Notes:
1. A6 through A12 must specify the same page address during each high to low transition of WE (or CE) after the software
code has been entered.
2. OE must be high only when WE and CE are both low.
10
AT28C64B
0270K–PEEPR–10/06
AT28C64B
22. Data Polling Characteristics(1)
Symbol
Parameter
tDH
Data Hold Time
tOEH
OE Hold Time
Min
Max
OE to Output Delay
tWR
Write Recovery Time
Units
0
ns
0
ns
(1)
tOE
Notes:
Typ
ns
0
ns
1. These parameters are characterized and not 100% tested. See “AC Read Characteristics” on page 6.
23. Data Polling Waveforms
tOEH
tDH
tWR
tOE
24. Toggle Bit Characteristics(1)
Symbol
Parameter
tDH
Data Hold Time
tOEH
OE Hold Time
Min
OE to Output Delay
tOEHP
OE High Pulse
Max
Units
10
ns
10
ns
(2)
tOE
tWR
Notes:
Typ
ns
Write Recovery Time
1. These parameters are characterized and not 100% tested.
150
ns
0
ns
2. See “AC Read Characteristics” on page 6.
25. Toggle Bit Waveforms(1)(2)(3)
tOEH
tOEHP
tDH
tOE
tWR
Notes:
1. Toggling either OE or CE or both OE and CE will operate toggle bit.
2. Beginning and ending state of I/O6 will vary.
3. Any address location may be used but the address should not vary.
11
0270K–PEEPR–10/06
26. Normalized ICC Graphs
12
AT28C64B
0270K–PEEPR–10/06
AT28C64B
27. Ordering Information(1)
27.1
Standard Package
ICC (mA)
tACC
(ns)
Active
150
Standby
Ordering Code
Package
Operation Range
0.1
AT28C64B-15JI
AT28C64B-15PI
AT28C64B-15SI
AT28C64B-15TI
32J
28P6
28S
28T
Industrial
(-40° C to 85° C)
40
Note:
1. See “Valid Part Numbers” on page 13.
27.2
Green Package Option (Pb/Halide-free)
tACC
(ns)
ICC (mA)
Active
150
40
Standby
Ordering Code
Package
Operation Range
0.1
AT28C64B-15JU
AT28C64B-15SU
AT28C64B-15TU
AT28C64B-15PU
32J
28S
28T
28P6
Industrial
(-40° C to 85° C)
28. Valid Part Numbers
The following table lists standard Atmel products that can be ordered.
Device Numbers
AT28C64B
Speed
15
Package and Temperature Combinations
JI, JU, PI, SI, SU, TI, TU, PU
29. Die Products
Reference Section: Parallel EEPROM Die Products
Package Type
32J
32-lead, Plastic J-leaded Chip Carrier (PLCC)
28P6
28-lead, 0.600" Wide, Plastic Dual Inline Package (PDIP)
28S
28-lead, 0.300" Wide, Plastic Gull Wing Small Outline (SOIC)
28T
28-lead, Plastic Thin Small Outline Package (TSOP)
13
0270K–PEEPR–10/06
30. Packaging Information
30.1
32J – PLCC
1.14(0.045) X 45˚
PIN NO. 1
IDENTIFIER
1.14(0.045) X 45˚
0.318(0.0125)
0.191(0.0075)
E1
E2
B1
E
B
e
A2
D1
A1
D
A
0.51(0.020)MAX
45˚ MAX (3X)
COMMON DIMENSIONS
(Unit of Measure = mm)
D2
Notes:
1. This package conforms to JEDEC reference MS-016, Variation AE.
2. Dimensions D1 and E1 do not include mold protrusion.
Allowable protrusion is .010"(0.254 mm) per side. Dimension D1
and E1 include mold mismatch and are measured at the extreme
material condition at the upper or lower parting line.
3. Lead coplanarity is 0.004" (0.102 mm) maximum.
SYMBOL
MIN
NOM
MAX
A
3.175
–
3.556
A1
1.524
–
2.413
A2
0.381
–
–
D
12.319
–
12.573
D1
11.354
–
11.506
D2
9.906
–
10.922
E
14.859
–
15.113
E1
13.894
–
14.046
E2
12.471
–
13.487
B
0.660
–
0.813
B1
0.330
–
0.533
e
NOTE
Note 2
Note 2
1.270 TYP
10/04/01
R
14
2325 Orchard Parkway
San Jose, CA 95131
TITLE
32J, 32-lead, Plastic J-leaded Chip Carrier (PLCC)
DRAWING NO.
REV.
32J
B
AT28C64B
0270K–PEEPR–10/06
AT28C64B
30.2
28P6 – PDIP
D
PIN
1
E1
A
SEATING PLANE
A1
L
B
B1
e
E
0º ~ 15º
C
COMMON DIMENSIONS
(Unit of Measure = mm)
REF
MIN
NOM
MAX
A
–
–
4.826
A1
0.381
–
–
D
36.703
–
37.338
E
15.240
–
15.875
E1
13.462
–
13.970
B
0.356
–
0.559
B1
1.041
–
1.651
L
3.048
–
3.556
C
0.203
–
0.381
eB
15.494
–
17.526
SYMBOL
eB
Notes:
1. This package conforms to JEDEC reference MS-011, Variation AB.
2. Dimensions D and E1 do not include mold Flash or Protrusion.
Mold Flash or Protrusion shall not exceed 0.25 mm (0.010").
e
NOTE
Note 2
Note 2
2.540 TYP
09/28/01
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
28P6, 28-lead (0.600"/15.24 mm Wide) Plastic Dual
Inline Package (PDIP)
DRAWING NO.
28P6
REV.
B
15
0270K–PEEPR–10/06
30.3
28S – SOIC
Dimensions in Millimeters and (Inches).
Controlling dimension: Millimeters.
0.51(0.020)
0.33(0.013)
7.60(0.2992) 10.65(0.419)
7.40(0.2914) 10.00(0.394)
PIN 1
1.27(0.50) BSC
TOP VIEW
18.10(0.7125)
17.70(0.6969)
2.65(0.1043)
2.35(0.0926)
0.30(0.0118)
0.10(0.0040)
SIDE VIEWS
0.32(0.0125)
0.23(0.0091)
0º ~ 8º
1.27(0.050)
0.40(0.016)
8/4/03
R
16
2325 Orchard Parkway
San Jose, CA 95131
TITLE
28S, 28-lead, 0.300" Body, Plastic Gull Wing Small Outline (SOIC)
JEDEC Standard MS-013
DRAWING NO.
REV.
28S
B
AT28C64B
0270K–PEEPR–10/06
AT28C64B
30.4
28T – TSOP
PIN 1
0º ~ 5º
c
Pin 1 Identifier Area
D1 D
L
b
e
L1
A2
E
A
GAGE PLANE
SEATING PLANE
COMMON DIMENSIONS
(Unit of Measure = mm)
A1
MIN
NOM
MAX
A
–
–
1.20
A1
0.05
–
0.15
A2
0.90
1.00
1.05
D
13.20
13.40
13.60
D1
11.70
11.80
11.90
Note 2
E
7.90
8.00
8.10
Note 2
L
0.50
0.60
0.70
SYMBOL
Notes:
1. This package conforms to JEDEC reference MO-183.
2. Dimensions D1 and E do not include mold protrusion. Allowable
protrusion on E is 0.15 mm per side and on D1 is 0.25 mm per side.
3. Lead coplanarity is 0.10 mm maximum.
L1
NOTE
0.25 BASIC
b
0.17
0.22
0.27
c
0.10
–
0.21
e
0.55 BASIC
12/06/02
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
28T, 28-lead (8 x 13.4 mm) Plastic Thin Small Outline
Package, Type I (TSOP)
DRAWING NO.
REV.
28T
C
17
0270K–PEEPR–10/06
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High-Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2006 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, Everywhere You Are® and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
Printed on recycled paper.
0270K–PEEPR–10/06