AZ767 SPDT SUBMINIATURE POWER RELAY FEATURES • • • • Low cost 10 Amp switching Epoxy sealed version available UL, CUR file E44211 CONTACTS GENERAL DATA Arrangement SPDT (1 Form C) Ratings Resistive Load: Max. switched power: Max. switched current: 90 W or 750 VA 3A Max. switched voltage: 150 VDC* or 380 VAC Life Expectancy Mechanical Electrical Minimum operations 1 x 107 1 x 105 at 5 A 250 VAC Res. Operate Time (typical) 8 ms at nominal coil voltage Release Time (typical) 5 ms at nominal coil voltage (with no coil suppression) * Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory Rated Load UL, CUR 3 A at 30 VDC / 250 VAC, 100k cycles Material Silver cadmium oxide, silver nickel Resistance < 100 milliohms initially COIL Power At Pickup Voltage (typical) 253 mW Max. Continuous Dissipation 1.25 W at 20°C (68°F) ambient Temperature Rise (at nominal voltage) 41°C (74°F) Temperature Max. 130°C (266°F) NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. Dielectric Strength 2500 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts Insulation Resistance 1000 megohms min. at 20°C 500 VDC 50% RH Dropout Greater than 5% of nominal coil voltage Ambient Temperature Operating At nominal coil voltage -40°C (-40°F) to 70°C (158°F) Vibration 0.062" (1.5 mm) DA at 10–50 Hz Shock 10 g operating, 100 g damage Enclosure P.B.T. polyester Terminals Tinned copper alloy, P. C. Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds Weight 6 grams Packing unit in pcs 50 per plastic tray / 500 per carton box ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2015-07-01 AZ767 RELAY ORDERING DATA STANDARD RELAYS COIL SPECIFICATIONS Nominal Coil VDC 3 ORDER NUMBER* Must Operate VDC 2.25 Max. Continuous VDC 5.0 Coil Resistance Ohm ± 10% 20 Form C (SPDT) 5 3.75 8.3 55 AZ767–1C–5D 6 4.5 10.0 80 AZ767–1C–6D 9 6.75 15.0 180 AZ767–1C–9D AZ767–1C–3D 12 9.0 20.0 320 AZ767–1C–12D 18 13.5 30.0 720 AZ767–1C–18D 24 18.0 40.0 1,280 AZ767–1C–24D 48 36.0 80.0 5,120 AZ767–1C–48D * “1C” denote silver cadmium oxide contacts. Substitute “1CB” in place of “1C” for silver nickel contacts. Add suffix “E” at the end of part number for epoxy sealed version. MECHANICAL DATA PC BOARD LAYOUT .059 [1.50] .073 [1.85] .100 [2.54] .058 [1.49] .417 MAX. [10.59] .740 MAX. [18.80] 5 x ø .052 [ø1.3] .300 [7.62] .441 [11.20] Viewed toward terminals WIRING DIAGRAMS .614 MAX. [15.59] Form C .147 [3.73] .073 [1.85] Viewed toward terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2015-07-01