FUJITSU SEMICONDUCTOR DATA SHEET DS04-20100-3E ASSP TIMING EXTRACTION BANDPASS FILTER (1.5 to 100MHz) F1/F2/F3 SERIES ■ DESCRIPTION The F1, F2 and F3 Series were developed as timing extraction filters for primary, secondary, and tertiary digital communication devices. This new all-solid-state bandpass filter (BPF) uses a piezoelectric with a large electromechanical coefficient (lithium tantalate: LiTaO3). The filter has a wide bandwidth, and is very stable. ■ FEATURES • • • • Wide frequency range 1.5 to 100MHz Wide fractional bandwidth (%): 0.1 to 2.5 Low insertion loss: 6dB or less Excellent temperature characteristics: 1.5 to 35MHz: ±400ppm or less (0 to 60°C) 36 to 100MHz: –30ppm/°C (0 to 60°C) • Small frequency deviation ∆fO < ±500ppm eliminating the need for adjustment • Highly reliable hermetically sealed package • Compatible with small 14-pin DIP IC ■ PACKAGE 14-PIN DIP SIZE METAL CASE F1/F2/F3 SERIES ■ PIN ASSIGNMENT (BOTTOM VIEW) Pin No. Pin name 1 IN 7 GND 8 NC 14 OUT 1 7 14 8 Description Input pin Ground pin No connection Output pin ■ MAXIMUM RATINGS Symbol Rating Unit Operating temperature Ta –20 to 80 °C Storage temperature Tstg –40 to 80 °C Insulation resistance IR 100 (100V DC) MΩ Frequency range –– 1.5 to 100 MHz Symbol Rating Unit Ta 0 to 70 °C Item ■ RECOMMENDED OPERATING CONDITIONS Item Operating temperature 2 F1/F2/F3 SERIES ■ STANDARD FREQUENCY Series Standard frequency Application 1.544MHz For the U.S. and Japan (primary group) 2.048MHz For Europe (primary group) 3.088MHz For the U.S. and Japan (primary group) 3.152MHz For the U.S. and Japan (primary group) 4.096MHz For Europe (primary group) 6.312MHz For the U.S. and Japan (secondary group) 8.192MHz For the U.S. and Japan (secondary group) 8.448MHz For Europe (secondary group) 12.624MHz For the U.S. and Japan (secondary group) 6.312 × 2 16.384MHz For the U.S. and Japan (secondary group) 8.192 × 2 16.896MHz For Europe (secondary group) 8.448 × 2 32.064MHz For Japan (tertiary group) 34.368MHz For Europe (tertiary group) 44.736MHz For the U.S. (tertiary group) F1 F2 F3 Remarks 1.544 × 2 2.048 × 2 3 F1/F2/F3 SERIES ■ ELECTRICAL CHARACTERISTICS F1 Series Item Symbol Condition Frequency deviation ∆fO Load Q Insertion loss Rating Unit Min. Typical Max. –– –500 –– +500 ppm Q –– 1000 –– 40 –– IL –– –– –– 6 dB Stop band attenuation AOUT fO ± 10MHz 20 –– –– dB Frequency stability with temperature ∆f (Ta) –– –400 –– +400 ppm Symbol Condition Frequency deviation ∆fO Load Q Q Remarks fO standard 25°C standard, Ta = 0 to 70°C F2 Series Item Rating Unit Min. Typical Max. –– –500 –– +500 ppm –– 1000 –– 40 –– IL –– –– –– 6 dB Stop band attenuation AOUT fO ± 10MHz 20 –– –– dB Frequency stability with temperature ∆f (Ta) –– –400 –– +400 ppm Symbol Condition Frequency deviation ∆fO Load Q Q Insertion loss Insertion loss Remarks fO standard 25°C standard, Ta = 0 to 70°C F3 Series Item 4 Rating Unit Min. Typical Max. –– –500 –– +500 ppm –– 200 –– 50 –– IL –– –– –– 6 dB Stop band attenuation AOUT fO ± 10MHz 20 –– –– dB Frequency stability with temperature ∆f (Ta) –– –1350 –– 750 ppm Remarks fO standard 25°C standard, Ta = 0 to 70°C F1/F2/F3 SERIES ■ ELECTRICAL CHARACTERISTICS Specification Standard frequency (MHz) Part number 1 1.544 2 No. Load Q Insertion loss, IL (dB) Phase rotation θ (degree) Terminating impedance Z (Ω) FAR-F1DA-1M5440-G201 110 ±20 3 or less –90±20 790 1.544 FAR-F1DA-1M5440-G202 110 ±20 3 or less –90±20 1000 3 1.544 FAR-F1DA-1M5440-G203 60 ±10 3 or less –95±10 2035/20pF 4 1.544 FAR-F1DA-1M5440-G205 110 ±20 3 or less –90±20 2000 5 2.048 FAR-F1DA-2M0480-G201 40 ±10 3 or less –90±10 2035 6 2.048 FAR-F1DA-2M0480-G202 100 ±20 3 or less –90±20 1000 7 3.088 FAR-F1DA-3M0880-G201 150 ±20 3 or less –90±20 640 8 3.152 FAR-F1DA-3M1520-G201 85 ±15 3 or less –90±15 1285 9 4.096 FAR-F1DA-4M0960-G201 110 ±20 3 or less –90±20 750 10 6.312 FAR-F1DA-6M3120-G201 110 ±20 3 or less –90±20 985 11 6.312 FAR-F1DA-6M3120-G202 110 ±20 3 or less –90±20 1000 12 8.192 FAR-F1DA-8M1920-G201 100 ±20 3 or less –90±20 980 13 8.448 FAR-F1DA-8M4480-G201 110 ±20 3 or less –90±20 980 14 12.624 FAR-F1DA-12M624-G201 100 ±20 3 or less –90±20 590 15 16.384 FAR-F1DA-16M384-G201 100 ±20 3 or less –90±20 410 16 16.896 FAR-F1DA-16M896-G201 100 ±20 3 or less –90±20 390 17 32.064 FAR-F2DA-32M064-G201 100 ±10 3 or less –90±15 100 18 34.368 FAR-F2DA-34M368-G201 100 ±10 3 or less –90±15 100 19 44.736 FAR-F3DA-44M736-G201 65 ±15 6 or less 38±10 105 ■ TEST CIRCUIT 50Ω OSC Z Z 50Ω LM 5 F1/F2/F3 SERIES ■ CHARACTERISTICS SAMPLE Pass band characteristic A : T/R (dB) B : A MAX 0.000 B MAX 180.0 Stop band characteristic θ 0 MKR dB GAIN deg PHASE 1544000.000Hz –722.721mdB –93.1330deg dB CENTER deg SPAN 1544000.000Hz 50000.000Hz A/DIV 1.000 B MIN –180.0 A : T/R (dB) B : A MAX 0.000 B MAX 180.0 θ 0 MKR dB GAIN deg PHASE 1544000.000Hz –724.276mdB deg A/DIV 5.000 B MIN –180.0 dB CENTER deg SPAN 1544000.000Hz 200000.000Hz Temperature characteristic Frequency change (ppm) F3 Series 1000 F2 Series F1 Series –1000 –20 0 20 40 60 Temperature (°C) 80 ■ PART NUMBERING SYSTEM [Example] FAR–F1DA– ➀ –G ➁ ➂ ➀ Series designation ➁ Frequency designation: The standard frequency is designated in six alphanumeric characters. M is used to designate the decimal point in MHz. Refer to “ELECTRIC CHARACTERISTICS” in detail Example: 1.544MHz: 1M5440 ➂ Serial number: 6 The serial number is assigned from 201 to 999 (201 is normal). F1/F2/F3 SERIES ■ MARKING Standard frequency Fujitu logo F F-1M5440 G201×××××× No. 1 pin position Lot number ■ DIMENSIONS Unit: mm (in.) 20.8 max (0.819) 10.7 (0.421) 5.5 (0.217) Hmax 18.3 (0.720) ø0.5 (0.020) 7 7.6 (0.299) 1 14 8 13.1 max (0.516) 15.2 (0.598) Series H F1 < 3 MHz 8.5 (0.335) F1 ≥ 3 MHz 5.8 (0.228) F2 5.8 (0.228) F3 5.8 (0.228) 7 FUJITSU LIMITED For further information please contact: Japan FUJITSU LIMITED Corporate Global Business Support Division Electronic Devices KAWASAKI PLANT, 4-1-1, Kamikodanaka Nakahara-ku, Kawasaki-shi Kanagawa 211-88, Japan Tel: (044) 754-3763 Fax: (044) 754-3329 North and South America FUJITSU MICROELECTRONICS, INC. Semiconductor Division 3545 North First Street San Jose, CA 95134-1804, U.S.A. Tel: (408) 922-9000 Fax: (408) 432-9044/9045 Europe FUJITSU MIKROELEKTRONIK GmbH Am Siebenstein 6-10 63303 Dreieich-Buchschlag Germany Tel: (06103) 690-0 Fax: (06103) 690-122 Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE. LIMITED #05-08, 151 Lorong Chuan New Tech Park Singapore 556741 Tel: (65) 281-0770 Fax: (65) 281-0220 All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document presented as examples of semiconductor device applications, and are not intended to be incorporated in devices for actual use. Also, FUJITSU is unable to assume responsibility for infringement of any patent rights or other rights of third parties arising from the use of this information or circuit diagrams. FUJITSU semiconductor devices are intended for use in standard applications (computers, office automation and other office equipment, industrial, communications, and measurement equipment, personal or household devices, etc.). CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.) are requested to consult with FUJITSU sales representatives before such use. The company will not be responsible for damages arising from such use without prior approval. Any semiconductor devices have inherently a certain rate of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Control Law of Japan, the prior authorization by Japanese government should be required for export of those products from Japan. F9703 FUJITSU LIMITED Printed in Japan 24