Document 207-1 SMT Power Inductors – DO1813H Series • High-current power inductance; up to 14 A saturating current • Rugged self-leaded construction for reliable soldering Designer’s Kit C331 contains 3 of each part Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant tin-silver over copper. Other terminations available at additional cost. Weight 278 – 315 mg Ambient temperature –40°C to +85°C with (40°C rise) Irms current. Maximum part temperature +125°C (ambient + temp rise). Derating. Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 1000 per 13″ reel Plastic tape: 16 mm wide, 0.3 mm thick, 12 mm pocket spacing, 5.4 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Part number1 DO1813H-181ML_ DO1813H-331ML_ DO1813H-561ML_ DO1813H-122ML_ DO1813H-222ML_ DO1813H-332ML_ DO1813H-472ML_ DO1813H-682ML_ DO1813H-822ML_ DO1813H-103ML_ DO1813H-153ML_ DO1813H-223ML_ DO1813H-333ML_ DO1813H-473ML_ L L typ DCR SRF ref ±20%2 max typ Isat3 Irms4 (µH) (µH) (Ohms) (MHz) (A) (A) 0.18 0.18 0.003 800 14.0 10.0 0.33 0.33 0.004 600 10.0 7.0 0.56 0.56 0.010 200 7.7 6.0 1.2 1.15 0.017 140 5.3 4.4 2.2 2.06 0.035 100 3.5 3.1 3.3 3.20 0.040 80 3.0 2.7 4.7 4.70 0.054 50 2.6 2.2 6.8 6.80 0.080 45 2.2 1.8 8.2 8.20 0.092 42 2.0 1.6 10.0 9.55 0.11 40 1.9 1.5 15.0 15.3 0.17 30 1.5 1.2 22.0 22.6 0.25 25 1.2 1.0 33.0 32.5 0.35 20 0.99 0.82 47.0 48.1 0.47 15 0.87 0.72 1. When ordering, please specify termination and packaging codes: DO1813H-473MLD Termination: L = RoHS compliant tin-silver over copper. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic tape, 1000 parts per full reel. B = Less than full reel. In tape, but not machine-ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance tested at 0.25 Vrms, 100 kHz, 0 Adc. 3. DC current at which the inductance drops 30% (typ) from its value without current. 4. Current that causes a 40°C temperature rise from 25°C ambient. 5. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Document 207-1 Revised 08/05/15 Document 207-2 SMT Power Inductors - DO1813H Series Typical L vs Frequency Internal code XXX X 0.240 6,10 max Dash number Typical L vs Current 0.075 1,91 0.160 4,06 See note 0.275 6,98 0.090 2.29 0.350 max 8,89 Recommended Land Pattern 0.180 dia 4,57 0.197 max 5,0 0.050 max 1,27 0.230 typ 5,84 Dimensions are in inches mm Note: 0.080 ±0.010 body 2,03 ±0,25 0.100 leads, based on -561 2,54 Document 207-2 Revised 08/05/15