HUFA75433S3S
N-Channel UltraFET® MOSFETs
60V, 64A, 16mΩ
General Description
Applications
These N-Channel power MOSFETs are manufactured using the innovative UltraFET® process. This advanced process technology achieves very low on-resistance per
silicon area, resulting in outstanding performance. This device is capable of withstanding high energy in the avalanche mode and the diode exhibits very low reverse
recovery time and stored charge. It was designed for use in
applications where power efficiency is important, such as
switching regulators, switching convertors, motor drivers,
relay drivers, low-voltage bus switches, and power management in portable and battery-operated products.
• Motor and Load Control
• Powertrain Management
Features
• 175°C Maximum Junction Temperature
• UIS Capability (Single Pulse and Repetitive Pulse)
• Ultra-Low On-Resistance rDS(ON) = 0.016Ω, VGS = 10V
D
D
G
G
S
TO-263AB
S
FDB Series
MOSFET Maximum Ratings TC = 25°C unless otherwise noted
Symbol
VDSS
Drain to Source Voltage
Parameter
Ratings
60
Units
V
VGS
Gate to Source Voltage
±20
V
Continuous (TC = 25oC, VGS = 10V)
64
A
Continuous (TC = 125oC, VGS = 10V, RθJA = 43oC/W)
5
A
Drain Current
ID
Pulsed
EAS
PD
TJ, TSTG
Figure 4
A
Single Pulse Avalanche Energy (Note 1)
250
mJ
Power dissipation
150
W
1
W/oC
-55 to 175
oC
Derate above 25oC
Operating and Storage Temperature
Thermal Characteristics
RθJC
Thermal Resistance Junction to Case TO-263
1
o
C/W
C/W
RθJA
Thermal Resistance Junction to Ambient TO-263
62
o
RθJA
Thermal Resistance Junction to Ambient TO-263, 1in2 copper pad area
43
oC/W
This product has been designed to meet the extreme test conditions and environment demanded by the automotive industry. For a
copy of the requirements, see AEC Q101 at: http://www.aecouncil.com/
Reliability data can be found at: http://www.fairchildsemi.com/products/discrete/reliability/index.html.
All Fairchild Semiconductor products are manufactured, assembled and tested under ISO9000 and QS9000 quality systems
certification.
©2002 Fairchild Semiconductor Corporation
Rev. A
HUFA75433S3S
March 2002
HUFA75433S3S
Package Marking and Ordering Information
Device Marking
75433S3
Device
HUFA75433S3ST
Package
TO-263
Reel Size
330mm
Tape Width
24mm
Quantity
800 units
75433S3
HUFA75433S3S
TO-263
Tube
N/A
50 units
Electrical Characteristics TC = 25°C unless otherwise noted
Symbol
Parameter
Test Conditions
Min
Typ
Max
Units
V
Off Characteristics
BVDSS
Drain to Source Breakdown Voltage
ID = 250µA, VGS = 0V
60
-
-
VDS = 55V, VGS = 0V
-
-
1
-
-
250
-
±100
nA
V
IDSS
Zero Gate Voltage Drain Current
VDS = 45V
VGS = 0V
IGSS
Gate to Source Leakage Current
VGS = ±20V
-
TC= 150oC
µA
On Characteristics
VGS(TH)
rDS(ON)
Gate to Source Threshold Voltage
Drain to Source On Resistance
VGS = VDS, ID = 250µA
2
-
4
ID = 64A, VGS = 10V
-
0.013
0.016
ID = 64A, VGS = 10V,
TJ = 175oC
-
0.029
0.035
-
1550
-
-
540
-
pF
-
150
-
pF
Ω
Dynamic Characteristics
CISS
Input Capacitance
COSS
Output Capacitance
CRSS
Reverse Transfer Capacitance
Qg(TOT)
Total Gate Charge at 20V
VGS = 0V to 20V
Qg(10)
Total Gate Charge at 10V
Qg(TH)
Threshold Gate Charge
Qgs
Gate to Source Gate Charge
VGS = 0V to 10V V = 30V
DD
VGS = 0V to 2V ID = 64A
Ig = 1.0mA
Qgd
Gate to Drain “Miller” Charge
Switching Characteristics
VDS = 25V, VGS = 0V,
f = 1MHz
pF
90
117
nC
-
50
65
nC
-
3
3.9
nC
-
6
-
nC
-
20
-
nC
(VGS = 10V)
tON
Turn-On Time
-
-
155
ns
td(ON)
Turn-On Delay Time
-
11
-
ns
tr
Rise Time
td(OFF)
Turn-Off Delay Time
tf
tOFF
-
92
-
ns
-
39
-
ns
Fall Time
-
26
-
ns
Turn-Off Time
-
-
98
ns
ISD = 64A
-
-
1.25
V
ISD = 32A
-
-
1.0
V
VDD = 30V, ID = 64A
VGS = 10V, RGS = 6.2Ω
Drain-Source Diode Characteristics
VSD
Source to Drain Diode Voltage
trr
Reverse Recovery Time
ISD = 64A, dISD/dt = 100A/µs
-
-
37
ns
QRR
Reverse Recovered Charge
ISD = 64A, dISD/dt = 100A/µs
-
-
42
nC
Notes:
1: Starting TJ = 25°C, L = 200µH, IAS = 50A
©2002 Fairchild Semiconductor Corporation
Rev. A
HUFA75433S3S
1.2
70
1.0
60
ID, DRAIN CURRENT (A)
POWER DISSIPATION MULTIPLIER
Typical Characteristics TC = 25°C unless otherwise noted
0.8
0.6
0.4
50
40
30
20
0.2
10
0
0
25
50
75
100
125
150
0
175
25
50
75
TC , CASE TEMPERATURE (oC)
100
125
150
175
TC, CASE TEMPERATURE (oC)
Figure 1. Normalized Power Dissipation vs
Ambient Temperature
Figure 2. Maximum Continuous Drain Current vs
Case Temperature
2
ZθJC, NORMALIZED
THERMAL IMPEDANCE
1
DUTY CYCLE - DESCENDING ORDER
0.5
0.2
0.1
0.05
0.02
0.01
PDM
0.1
t1
t2
NOTES:
DUTY FACTOR: D = t1/t2
PEAK TJ = PDM x ZθJC x RθJC + TC
SINGLE PULSE
0.01
10-5
10-4
10-3
10-2
10-1
100
101
t, RECTANGULAR PULSE DURATION (s)
Figure 3. Normalized Maximum Transient Thermal Impedance
800
TC = 25oC
IDM, PEAK CURRENT (A)
TRANSCONDUCTANCE
MAY LIMIT CURRENT
IN THIS REGION
FOR TEMPERATURES
ABOVE 25oC DERATE PEAK
CURRENT AS FOLLOWS:
175 - TC
I = I25
150
VGS = 20V
100
VGS = 10V
50
10-5
10-4
10-3
10-2
10-1
100
101
t, PULSE WIDTH (s)
Figure 4. Peak Current Capability
©2002 Fairchild Semiconductor Corporation
Rev. A
HUFA75433S3S
Typical Characteristics TC = 25°C unless otherwise noted
1000
IAS, AVALANCHE CURRENT (A)
ID, DRAIN CURRENT (A)
1000
100µs
100
1ms
OPERATION IN THIS
AREA MAY BE
LIMITED BY rDS(ON)
10
10ms
SINGLE PULSE
TJ = MAX RATED
TC = 25oC
If R = 0
tAV = (L)(IAS)/(1.3*RATED BVDSS - VDD)
If R ≠ 0
tAV = (L/R)ln[(IAS*R)/(1.3*RATED BVDSS - VDD) +1]
100
STARTING TJ = 25oC
STARTING TJ = 150oC
10
1
1
1
10
0.001
100
VDS, DRAIN TO SOURCE VOLTAGE (V)
0.01
Figure 5. Forward Bias Safe Operating Area
100
PULSE DURATION = 80µs
DUTY CYCLE = 0.5% MAX
VDD = 15V
VGS = 20V
ID, DRAIN CURRENT (A)
ID , DRAIN CURRENT (A)
10
1
Figure 6. Unclamped Inductive Switching
Capability
100
75
50
TJ = 175oC
TJ = 25oC
25
VGS = 10V
VGS = 6V
75
50
VGS = 5V
25
PULSE DURATION = 80µs
DUTY CYCLE = 0.5% MAX
TJ = -55oC
TC = 25oC
0
0
3.0
3.5
4.0
4.5
5.0
5.5
VGS , GATE TO SOURCE VOLTAGE (V)
0
6.0
0.5
1.0
1.5
2.0
VDS , DRAIN TO SOURCE VOLTAGE (V)
Figure 7. Transfer Characteristics
Figure 8. Saturation Characteristics
1.2
2.5
PULSE DURATION = 80µs
DUTY CYCLE = 0.5% MAX
VGS = VDS, ID = 250µA
2.0
NORMALIZED GATE
THRESHOLD VOLTAGE
NORMALIZED DRAIN TO SOURCE
ON RESISTANCE
0.1
tAV, TIME IN AVALANCHE (ms)
NOTE: Refer to Fairchild Application Notes AN7514 and AN7515.
1.5
1.0
1.0
0.8
VGS = 10V, ID = 64A
0.5
0.6
-80
-40
0
40
80
120
160
TJ, JUNCTION TEMPERATURE (oC)
Figure 9. Normalized Drain to Source On
Resistance vs Junction Temperature
©2002 Fairchild Semiconductor Corporation
200
-80
-40
0
40
80
120
160
200
TJ, JUNCTION TEMPERATURE (oC)
Figure 10. Normalized Gate Threshold Voltage vs
Junction Temperature
Rev. A
HUFA75433S3S
Typical Characteristics TC = 25°C unless otherwise noted
1.2
4000
CISS = CGS + CGD
C, CAPACITANCE (pF)
NORMALIZED DRAIN TO SOURCE
BREAKDOWN VOLTAGE
ID = 250µA
1.1
1.0
CRSS = CGD
1000
COSS ≅ CDS + CGD
100
VGS = 0V, f = 1MHz
60
0.9
-80
-40
0
40
80
120
160
0.1
200
1
TJ , JUNCTION TEMPERATURE (oC)
10
60
VDS , DRAIN TO SOURCE VOLTAGE (V)
Figure 11. Normalized Drain to Source
Breakdown Voltage vs Junction Temperature
Figure 12. Capacitance vs Drain to Source
Voltage
VGS , GATE TO SOURCE VOLTAGE (V)
10
VDD = 30V
8
6
4
WAVEFORMS IN
DESCENDING ORDER:
ID = 64A
ID = 40A
2
0
0
10
20
30
40
50
Qg, GATE CHARGE (nC)
Figure 13. Gate Charge Waveforms for Constant Gate Currents
Test Circuits and Waveforms
VDS
BVDSS
tP
L
VDS
VARY tP TO OBTAIN
REQUIRED PEAK IAS
IAS
+
RG
VDD
VDD
-
VGS
DUT
tP
0V
IAS
0.01Ω
0
tAV
Figure 14. Unclamped Energy Test Circuit
©2002 Fairchild Semiconductor Corporation
Figure 15. Unclamped Energy Waveforms
Rev. A
HUFA75433S3S
Test Circuits and Waveforms (Continued)
VDS
VDD
RL
Qg(TOT)
VDS
VGS = 20V
VGS
Qg(10)
+
VDD
VGS =10V
VGS
DUT
VGS = 2V
Ig(REF)
0
Qg(TH)
Qgs
Qgd
Ig(REF)
0
Figure 16. Gate Charge Test Circuit
Figure 17. Gate Charge Waveforms
VDS
tON
tOFF
td(ON)
td(OFF)
RL
tf
tr
VDS
90%
90%
+
VGS
VDD
-
10%
10%
0
DUT
90%
RGS
VGS
50%
50%
PULSE WIDTH
VGS
0
Figure 18. Switching Time Test Circuit
©2002 Fairchild Semiconductor Corporation
10%
Figure 19. Switching Time Waveforms
Rev. A
HUFA75433S3S
Thermal Resistance vs. Mounting Pad Area
( T JM – T A )
P DM = ----------------------------RθJA
(EQ. 1)
In using surface mount devices such as the TO-263
package, the environment in which it is applied will have a
significant influence on the part’s current and maximum
power dissipation ratings. Precise determination of PDM is
complex and influenced by many factors:
1. Mounting pad area onto which the device is attached and
whether there is copper on one side or both sides of the
board.
80
RθJA = 26.51+ 19.84/(0.262+Area)
60
RθJA (oC/W)
The maximum rated junction temperature, TJM, and the
thermal resistance of the heat dissipating path determines
the maximum allowable device power dissipation, PDM, in an
application.
Therefore the application’s ambient
temperature, TA (oC), and thermal resistance RθJA (oC/W)
must be reviewed to ensure that TJM is never exceeded.
Equation 1 mathematically represents the relationship and
serves as the basis for establishing the rating of the part.
40
20
0.1
1
10
AREA, TOP COPPER AREA (in2)
Figure 20. Thermal Resistance vs Mounting
Pad Area
2. The number of copper layers and the thickness of the
board.
3. The use of external heat sinks.
4. The use of thermal vias.
5. Air flow and board orientation.
6. For non steady state applications, the pulse width, the
duty cycle and the transient thermal response of the part,
the board and the environment they are in.
Fairchild provides thermal information to assist the
designer’s preliminary application evaluation. Figure 20
defines the RθJA for the device as a function of the top
copper (component side) area. This is for a horizontally
positioned FR-4 board with 1oz copper after 1000 seconds
of steady state power with no air flow. This graph provides
the necessary information for calculation of the steady state
junction temperature or power dissipation. Pulse
applications can be evaluated using the Fairchild device
Spice thermal model or manually utilizing the normalized
maximum transient thermal impedance curve.
Thermal resistances corresponding to other copper areas
can be obtained from Figure 20 or by calculation using
Equation 2. The area, in square inches is the top copper
area including the gate and source pads.
19.84
( 0.268 + Area )
R θ JA = 26.51 + -------------------------------------
©2002 Fairchild Semiconductor Corporation
(EQ. 2)
Rev. A
HUFA75433S3S
PSPICE Electrical Model
.SUBCKT HUFA75433S3S
CA 12 8 2.5e-9
CB 15 14 2.8e-9
CIN 6 8 1.4e-9
February 2002
LDRAIN
DPLCAP
10
DBODY 7 5 DBODYMOD
DBREAK 5 11 DBREAKMOD
DPLCAP 10 5 DPLCAPMOD
EVTHRES
+ 19 8
+
LGATE
GATE
1
EVTEMP
RGATE +
18 22
9
20
+
EBREAK
16
17
18
-
DBODY
MWEAK
6
MMED
MSTRO
LSOURCE
CIN
8
SOURCE
3
7
RSOURCE
RLGATE 1 9 65.7
RLDRAIN 2 5 10
RLSOURCE 3 7 34
RLSOURCE
S1A
12
S2A
13
8
14
13
S1B
17
18
RVTEMP
S2B
13
CA
RBREAK
15
CB
6
8
EGS
-
19
IT
14
+
+
RBREAK 17 18 RBREAKMOD 1
RDRAIN 50 16 RDRAINMOD 2.7e-3
RGATE 9 20 1.53
RSLC1 5 51 RSLCMOD 1e-6
RSLC2 5 50 1e3
RSOURCE 8 7 RSOURCEMOD 6.9e-3
RVTHRES 22 8 RVTHRESMOD 1
RVTEMP 18 19 RVTEMPMOD 1
11
50
21
RLGATE
MMED 16 6 8 8 MMEDMOD
MSTRO 16 6 8 8 MSTROMOD
MWEAK 16 21 8 8 MWEAKMOD
ESLC
RDRAIN
6
8
ESG
DBREAK
+
RSLC2
5
51
LGATE 1 9 6.57e-9
LDRAIN 2 5 1e-9
LSOURCE 3 7 3.4e-9
RLDRAIN
RSLC1
51
EBREAK 11 7 17 18 65.5
EDS 14 8 5 8 1
EGS 13 8 6 8 1
ESG 6 10 6 8 1
EVTHRES 6 21 19 8 1
EVTEMP 20 6 18 22 1
IT 8 17 1
DRAIN
2
5
VBAT
5
8
EDS
-
+
8
22
RVTHRES
S1A 6 12 13 8 S1AMOD
S1B 13 12 13 8 S1BMOD
S2A 6 15 14 13 S2AMOD
S2B 13 15 14 13 S2BMOD
VBAT 22 19 DC 1
ESLC 51 50 VALUE={(V(5,51)/ABS(V(5,51)))*(PWR(V(5,51)/(1e-6*215),2.5))}
.MODEL DBODYMOD D (IS = 1.3e-12 RS = 3.05e-3 TRS1 = 2.4e-3 TRS2 = 1.5e-7 CJO = 1.92e-9 TT = 5e-9 M = 0.50 XTI=4.5)
.MODEL DBREAKMOD D (RS = 2.2 TRS1 = 2.4e-3 TRS2 = -2e-5)
.MODEL DPLCAPMOD D (CJO = 1.93e-9 IS = 1e-30 N = 10 M = 0.79)
.MODEL MmedMOD NMOS (VTO=2.93 KP=2.6 IS=1e-30 N=10 TOX=1 L=1u W=1u RG=1.53)
.MODEL MstroMOD NMOS (VTO=3.55 KP=70 IS=1e-30 N=10 TOX=1 L=1u W=1u)
.MODEL MweakMOD NMOS (VTO=2.62 KP=0.05 IS=1e-30 N=10 TOX=1 L=1u W=1u RG=15.3 RS=0.1)
.MODEL RBREAKMOD RES (TC1 =1.2e-3 TC2 = -1.7e-8)
.MODEL RDRAINMOD RES (TC1 = 2e-2 TC2 = 5.1e-5)
.MODEL RSLCMOD RES (TC1 = 3e-3 TC2 = 2.9e-6)
.MODEL RSOURCEMOD RES (TC1 = 1e-3 TC2 = 1e-6)
.MODEL RVTEMPMOD RES (TC1 = -2.8e-3 TC2 = 1e-6)
.MODEL RVTHRESMOD RES (TC1 = -2.1e-3 TC2 = -1.1e-5)
.MODEL S1AMOD VSWITCH (RON = 1e-5 ROFF = 0.1 VON = -6 VOFF= -3)
.MODEL S1BMOD VSWITCH (RON = 1e-5 ROFF = 0.1 VON = -3 VOFF= -6)
.MODEL S2AMOD VSWITCH (RON = 1e-5 ROFF = 0.1 VON = -0.4 VOFF= 0.3)
.MODEL S2BMOD VSWITCH (RON = 1e-5 ROFF = 0.1 VON = 0.3 VOFF= -0.4)
.ENDS
Note: For further discussion of the PSPICE model, consult A New PSPICE Sub-Circuit for the Power MOSFET Featuring Global
Temperature Options; IEEE Power Electronics Specialist Conference Records, 1991, written by William J. Hepp and C. Frank
Wheatley.
©2002 Fairchild Semiconductor Corporation
Rev. A
HUFA75433S3S
SABER Electrical Model
REV February 2002
template HUFA75433S3S n2,n1,n3
electrical n2,n1,n3
{
var i iscl
dp..model dbodymod = (isl=1.3e-12,rs=3.05e-3,trs1=2.4e-3,trs2=1.5e-7,cjo=1.92e-9,tt=5e-9,m=0.50,xti=4.5)
dp..model dbreakmod = (rs=2.2,trs1=2.4e-3,trs2=-2e-5)
dp..model dplcapmod = (cjo=1.93e-9,isl=10e-30,nl=10,m=0.79)
m..model mmedmod = (type=_n,vto=2.93,kp=2.6,is=1e-30, tox=1)
m..model mstrongmod = (type=_n,vto=3.55,kp=70,is=1e-30, tox=1)
m..model mweakmod = (type=_n,vto=2.62,kp=0.05,is=1e-30, tox=1,rs=0.1)
sw_vcsp..model s1amod = (ron=1e-5,roff=0.1,von=-6,voff=-3)
sw_vcsp..model s1bmod = (ron=1e-5,roff=0.1,von=-3,voff=-6)
sw_vcsp..model s2amod = (ron=1e-5,roff=0.1,von=-0.4,voff=0.3)
sw_vcsp..model s2bmod = (ron=1e-5,roff=0.1,von=0.3,voff=-0.4)
c.ca n12 n8 = 2.5e-9
c.cb n15 n14 = 2.8e-9
DPLCAP 5
c.cin n6 n8 = 1.4e-9
LDRAIN
DRAIN
2
10
dp.dbody n7 n5 = model=dbodymod
dp.dbreak n5 n11 = model=dbreakmod
dp.dplcap n10 n5 = model=dplcapmod
RLDRAIN
RSLC1
51
RSLC2
ISCL
spe.ebreak n11 n7 n17 n18 = 65.5
spe.eds n14 n8 n5 n8 = 1
spe.egs n13 n8 n6 n8 = 1
spe.esg n6 n10 n6 n8 = 1
spe.evthres n6 n21 n19 n8 = 1
spe.evtemp n20 n6 n18 n22 = 1
i.it n8 n17 = 1
RDRAIN
6
8
ESG
GATE
1
EVTEMP
RGATE + 18 22
9
20
6
EBREAK
+
17
18
-
MMED
RLGATE
CA
m.mmed n16 n6 n8 n8 = model=mmedmod, l=1u, w=1u
m.mstrong n16 n6 n8 n8 = model=mstrongmod, l=1u, w=1u
m.mweak n16 n21 n8 n8 = model=mweakmod, l=1u, w=1u
DBODY
MWEAK
MSTRO
l.lgate n1 n9 = 6.57e-9
l.ldrain n2 n5 = 1e-9
l.lsource n3 n7 = 3.4e-9
res.rlgate n1 n9 = 65.7
res.rldrain n2 n5 = 10
res.rlsource n3 n7 = 34
11
EVTHRES
16
21
+ 19 8
+
LGATE
DBREAK
50
-
CIN
8
LSOURCE
7
RSOURCE
S1A
12
13
8
S2A
14
13
S1B
RLSOURCE
RBREAK
15
17
18
RVTEMP
S2B
13
CB
+
+
6
8
EGS
-
SOURCE
3
19
IT
14
VBAT
5
8
EDS
-
res.rbreak n17 n18 = 1, tc1=1.2e-3,tc2=-1.7e-8
res.rdrain n50 n16 = 2.7e-3, tc1=2e-2,tc2=5.1e-5
res.rgate n9 n20 = 1.53
res.rslc1 n5 n51 = 1e-6, tc1=3e-3,tc2=2.9e-6
res.rslc2 n5 n50 = 1e3
res.rsource n8 n7 = 6.9e-3, tc1=1e-3,tc2=1e-6
res.rvthres n22 n8 = 1, tc1=-2.1e-3,tc2=-1.1e-5
res.rvtemp n18 n19 = 1, tc1=-2.8e-3,tc2=1e-6
+
8
22
RVTHRES
sw_vcsp.s1a n6 n12 n13 n8 = model=s1amod
sw_vcsp.s1b n13 n12 n13 n8 = model=s1bmod
sw_vcsp.s2a n6 n15 n14 n13 = model=s2amod
sw_vcsp.s2b n13 n15 n14 n13 = model=s2bmod
v.vbat n22 n19 = dc=1
equations {
i (n51->n50) +=iscl
iscl: v(n51,n50) = ((v(n5,n51)/(1e-9+abs(v(n5,n51))))*((abs(v(n5,n51)*1e6/215))** 2.5))}
}
©2002 Fairchild Semiconductor Corporation
Rev. A
th
HUFA75433S3S
SPICE Thermal Model
JUNCTION
REV 23 February 2002
HUFA75433S3
CTHERM1 TH 6 4.9e-4
CTHERM2 6 5 4.5e-3
CTHERM3 5 4 6.0e-3
CTHERM4 4 3 8.5e-3
CTHERM5 3 2 0.8e-2
CTHERM6 2 TL 4.2e-2
RTHERM1
CTHERM1
6
RTHERM1 TH 6 6.0e-4
RTHERM2 6 5 6.8e-3
RTHERM3 5 4 3.3e-2
RTHERM4 4 3 9.9e-2
RTHERM5 3 2 3.3e-1
RTHERM6 2 TL 3.5e-1
RTHERM2
CTHERM2
5
SABER Thermal Model
SABER thermal model HUFA75433S3
template thermal_model th tl
thermal_c th, tl
{
ctherm.ctherm1 th 6 =4.9e-4
ctherm.ctherm2 6 5 =4.5e-3
ctherm.ctherm3 5 4 =6.0e-3
ctherm.ctherm4 4 3 =8.5e-3
ctherm.ctherm5 3 2 =0.8e-2
ctherm.ctherm6 2 tl =4.2e-2
rtherm.rtherm1 th 6 =6.0e-4
rtherm.rtherm2 6 5 =6.8e-3
rtherm.rtherm3 5 4 =3.3e-2
rtherm.rtherm4 4 3 =9.9e-2
rtherm.rtherm5 3 2 =3.3e-1
rtherm.rtherm6 2 tl =3.5e-1
}
RTHERM3
CTHERM3
4
RTHERM4
CTHERM4
3
RTHERM5
CTHERM5
2
CTHERM6
RTHERM6
tl
©2002 Fairchild Semiconductor Corporation
CASE
Rev. A
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is
not intended to be an exhaustive list of all such trademarks.
ACEx
Bottomless
CoolFET
CROSSVOLT
DenseTrench
DOME
EcoSPARK
E2CMOSTM
EnSignaTM
FACT
FACT Quiet Series
FAST â
FASTr
FRFET
GlobalOptoisolator
GTO
HiSeC
I2C
ISOPLANAR
LittleFET
MicroFET
MicroPak
MICROWIRE
OPTOLOGIC â
OPTOPLANAR
PACMAN
POP
Power247
PowerTrench â
QFET
QS
QT Optoelectronics
Quiet Series
SILENT SWITCHER â UHC
SMART START
UltraFET â
SPM
VCX
STAR*POWER
Stealth
SuperSOT-3
SuperSOT-6
SuperSOT-8
SyncFET
TinyLogic
TruTranslation
STAR*POWER is used under license
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER
NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD
DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT
OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT
RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY
FAIRCHILDS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:
2. A critical component is any component of a life
1. Life support devices or systems are devices or
support device or system whose failure to perform can
systems which, (a) are intended for surgical implant into
be reasonably expected to cause the failure of the life
the body, or (b) support or sustain life, or (c) whose
support device or system, or to affect its safety or
failure to perform when properly used in accordance
with instructions for use provided in the labeling, can be
effectiveness.
reasonably expected to result in significant injury to the
user.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification
Product Status
Definition
Advance Information
Formative or
In Design
This datasheet contains the design specifications for
product development. Specifications may change in
any manner without notice.
Preliminary
First Production
This datasheet contains preliminary data, and
supplementary data will be published at a later date.
Fairchild Semiconductor reserves the right to make
changes at any time without notice in order to improve
design.
No Identification Needed
Full Production
This datasheet contains final specifications. Fairchild
Semiconductor reserves the right to make changes at
any time without notice in order to improve design.
Obsolete
Not In Production
This datasheet contains specifications on a product
that has been discontinued by Fairchild semiconductor.
The datasheet is printed for reference information only.
Rev. H5