LANK “H” Series 3000VDC I/O Isolation Single and Dual Output 3 Watt DC/DC Converter 24 Pin DIP & SMT Package 2:1 Wide Input Voltage Range FEATURES ● 3000VDC I/O Isolation ● Over Current Protection ● MTBF > 3,000,000 Hours ● High Efficiency up to 80% ● 2:1 Wide Input Voltage Range ● 3 Watts Regulated Output Power ● International Safety Standard Approval ● Standard 24 Pin DIP Package and SMT Type Package UL E193009 TUV CB CE MARK SPECIFICATIONS: LANK “H” Series All specifications apply @ 25°C ambient unless otherwise noted INPUT SPECIFICATIONS GENERAL SPECIFICATIONS (CONTINUED) Input Voltage Range ............ 5V nominal input ......................... 4.5 - 6VDC 12V nominal input ....................... 9 - 18 VDC 24V nominal input ..................... 18 - 36 VDC 48V nominal input ..................... 36 - 75 VDC Isolation Voltage (Input to Output)......................................... 3000VDC min. Input Filter ....................................................................................... Pi Type ENVIRONMENTAL SPECIFICATIONS Input Surge Voltage (100ms max) ....... 5V input .............................15VDC 12V input ..........................36 VDC 24V input ..........................50 VDC 48V input ........................100 VDC 9 Isolation Resistance ...............................................................10 ohms min. Isolation Capacitance ................................................................ 300pF max. Operating Temperature Standard ........................................................................... -25°C ~ +71°C “I” Suffix (See Note 7) ....................................................... -40°C ~ +71°C Input Reflected Ripple Current (Note 2)......................................120mAp-p (nominal Vin and full load) Storage Temperature .......................................................... -55°C ~ +105°C Start Up Time (nominal Vin and constant resistive load) .............30ms typ. Thermal Shock .................................................................... MIL-STD-810D OUTPUT SPECIFICATIONS Vibration ................................10~55Hz, 10G, 30 minutes along X, Y, and Z Output Voltage ..............................................................................see table MTBF (See Note 3) ............................................................ 3.69 x 10 hours Voltage Accuracy (nominal Vin and full load) ...................................... ±1% PHYSICAL SPECIFICATIONS Output Current ..............................................................................see table Weight DIP Type.............................................................................. 14g (0.48 oz) SMT Type ............................................................................ 15g (0.52 oz) Output Power .......................................................................... 3 watts max. Line Regulation (LL to HL at FL)....................................................... ±0.2% Load Regulation (25% to 100% FL)......... Single Output.................. ±0.2% Dual Output ....................... ±2% Relative Humidity...................................................................5% to 95% RH 6 Dimensions................... 1.25 x 0.80 x 0.40 inches (31.8 x 20.3 x 10.2 mm) Case Material ..................................................Non-conductive black plastic Cross Regulation (Dual) (Asymmetrical load 25% / 100% FL) ............ ±5% Base Material...................................................Non-conductive black plastic Minimum Load (See Note 1) ...................................................... 10% of FL Potting material..................................................................Epoxy (UL94-V0) Ripple/Noise (20 MHz BW) ...... 3.3V and 5V outputs ...................75mVp-p others.........................1%/p-p of Vout max SAFETY & EMC Temperature Coefficient ................................................. ±0.02% / °C max. Transient Response Recovery Time (25% load step) .......................500us PROTECTION SPECIFICATIONS Approvals and Standards .................. IEC60950-1, UL60950-1, EN60950-1 Conducted Emissions................. EN55022 ...................................... Class A Radiated Emissions.................... EN55022 ...................................... Class A ESD ............................................ EN61000-4-2.....................Perf. Criteria B Over Load Protection (% of full load at nominal input)................ 180% typ. Radiated Immunity...................... EN61000-4-3.....................Perf. Criteria A Short Circuit Protection. ............................ continuous, automatic recovery Fast Transient............................. EN61000-4-4.....................Perf. Criteria B GENERAL SPECIFICATIONS Surge .......................................... EN61000-4-5.....................Perf. Criteria B Efficiency.......................................................................................see table Conducted Immunity................... EN61000-4-6.....................Perf. Criteria A Switching Frequency................................................................100KHz typ. Due to advances in technology, specifications subject to change without notice Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 LANK “H” Series 3000VDC I/O Isolation Single and Dual Output 3 Watt DC/DC Converter 24 Pin DIP & SMT Package 2:1 Wide Input Voltage Range OUTPUT VOLTAGE / CURRENT RATING CHART Model Number LANK53.3W3H LANK505W3H LANK512W3H LANK515W3H LANK505DW3H LANK512DW3H LANK515DW3H LANK123.3W3H LANK1205W3H LANK1212W3H LANK1215W3H LANK1205DW3H LANK1212DW3H LANK1215DW3H LANK243.3W3H LANK2405W3H LANK2412W3H LANK2415W3H LANK2405DW3H LANK2412DW3H LANK2415DW3H LANK483.3W3H LANK4805W3H LANK4812W3H LANK4815W3H LANK4805DW3H LANK4812DW3H LANK4815DW3H Input Range 5 VDC (4.5 – 6 VDC) 12VDC (9 – 18 VDC) 24 VDC (18 – 36 VDC) 48VDC (36 – 75 VDC) Output Voltage Output Current Input Current (4) Efficiency (5) 3.3 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 600mA 600mA 250mA 200mA ± 300mA ± 125mA ± 100mA 600mA 600mA 250mA 200mA ± 300mA ± 125mA ± 100mA 600mA 600mA 250mA 200mA ± 300mA ± 125mA ± 100mA 600mA 600mA 250mA 200mA ± 300mA ± 125mA ± 100mA 649mA 909mA 835mA 845mA 857mA 845mA 870mA 266mA 353mA 333mA 343mA 348mA 338mA 333mA 123mA 174mA 164mA 164mA 172mA 167mA 167mA 61mA 88mA 84mA 84mA 86mA 84mA 84mA 66% 70% 76% 75% 74% 75% 73% 70% 75% 79% 77% 76% 78% 79% 71% 76% 80% 80% 77% 79% 79% 72% 75% 79% 79% 77% 79% 79% Capacitor Load (6) (max) 2200uF 1000uF 170uF 110uF ± 500uF ± 96uF ± 47uF 2200uF 1000uF 170uF 110uF ± 500uF ± 96uF ± 47uF 2200uF 1000uF 170uF 110uF ± 500uF ± 96uF ± 47uF 2200uF 1000uF 170uF 110uF ± 500uF ± 96uF ± 47uF NOTES 1. LANK ”H” Series requires a minimum 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification. 2. Please add an external filter at converter input terminals when measuring input reflected ripple, as figure 1. L: Simulated source impedance of 12uH C: Nippon chemi-con KMF series 47uF/100V 3. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40ºC. (Ground fixed and controlled environment) 4. Maximum value at nominal input voltage and full load of standard type. 5. Typical value at nominal input voltage and full load. 6. Test by minimum Vin and constant resistive load. 7. Add suffix “I” for –40°C to +71°C operation. 8. Add suffix “S” for surface mount type. Figure 1 Figure 1 Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 LANK “H” Series 3000VDC I/O Isolation Single and Dual Output 3 Watt DC/DC Converter 24 Pin DIP & SMT Package 2:1 Wide Input Voltage Range DERATING CURVE MECHANICAL DRAWING DIP TYPE SMT TYPE (add suffix “S”) 1. All dimensions in Inches (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) 2. Pin pitch tolerance ±0.014(0.35) DIP PIN CONNECTION SMT PIN CONNECTION PIN SINGLE DUAL PIN SINGLE DUAL PIN SINGLE DUAL PIN SINGLE DUAL 2 3 - INPUT - INPUT - INPUT - INPUT 23 22 + INPUT + INPUT + INPUT + INPUT 2 3 - INPUT - INPUT - INPUT - INPUT 23 22 + INPUT + INPUT + INPUT + INPUT 9 10 11 NC NC NC COMMON NC - OUTPUT 16 15 14 9 10 11 Others NC NC NC NC - OUTPUT COMMON NC NC + OUTPUT + OUTPUT 16 - OUTPUT COMMON COMMON NC 15 NC NC - OUTPUT 14 + OUTPUT + OUTPUT NC Others NC NC Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797