2-and 4-Channel Low Capacitance ESD Protection Arrays CM1293A Features • • • • • • • • Two and four channels of ESD protection Provides ESD protection to IEC61000-4-2 • ±8kV contact discharge Low loading capacitance of 2.0pF max. Low clamping voltage Channel I/O to I/O capacitance 1.5pF typical Zener diode protects supply rail and eliminates the need for external by-pass capacitors Each I/O pin can withstand over 1000 ESD strikes* Available in RoHS-compliant, lead-free SOT and MSOP packages Applications • • • • DVI ports, HDMI ports in notebooks, set top boxes, digital TVs, LCD displays Serial ATA ports in desktop PCs and hard disk drives PCI Express ports General purpose high-speed data line ESD protection Product Description The CM1293A family of diode arrays has been designed to provide ESD protection for electronic components or subsystems requiring minimal capacitive loading. These devices are ideal for protecting systems with high data and clock rates or for circuits requiring low capacitive loading. Each ESD channel consists of a pair of diodes in series that steer the positive or negative ESD current pulse to either the positive (VP) or negative (VN) supply rail. A Zener diode is embedded between VP and VN which helps protect the VCC rail against ESD strikes. The CM1293A protects against ESD pulses up to ±8kV contact discharge) per the IEC 61000-4-2 Level 4 standard. This device is particularly well-suited for protecting systems using high-speed ports such as USB2.0, IEEE1394 (Firewire, iLink), Serial ATA, DVI, HDMI, and corresponding ports in removable storage, digital camcorders, DVD-RW drives and other applications where extremely low loading capacitance with ESD protection are required in a small package footprint. The CM1293A family of devices is available with RoHS-compliant, lead-free finishing. Block Diagram *Standard test condition is IEC61000-4-2 level 4 test circuit with each pin subjected to ±8kV contact discharge for 1000 pulses. Discharges are timed at 1 second intervals and all 1000 strikes are completed in one continuous test run. The part is then subjected to standard production test to verify that all of the tested parameters are within spec after the 1000 strikes. ©2010 SCILLC. All rights reserved. April 2010 – Rev. 4 Publication Order Number: CM1293A/D CM1293A To p View To p View (4) (1) VP (5) NC (1) (2) VN (2) (2) (1) (3) CH1 (3) CH2 (4) (6) CH1 (1) NC (10) NC (2) CH4 (9) (5) (3) (4) (3) (8) CH2 (4) NC (7) NC (5) CH3 (6) 5-Lead SOT23-5 10-Lead MSOP-10 PIN DESCRIPTIONS 2-CHANNEL, 5-LEAD SOT23-5 PACKAGE 2-CHANNEL, 4-LEAD SOT143-4 PACKAGE PIN NAME TYPE DESCRIPTION PIN NAME 1 VN GND Negative voltage supply rail 2 CH1 I/O 3 CH2 I/O 4 VP PWR 1 NC ESD Channel 2 VN GND ESD Channel 3 CH1 I/O ESD Channel Positive voltage supply rail 4 CH2 I/O ESD Channel 5 VP PWR 4-CHANNEL, 10-LEAD MSOP-10 PACKAGE PIN NAME TYPE 1 CH1 I/O 2 NC 3 VP PWR 4 CH2 I/O 5 NC 6 CH3 7 NC 8 VN GND 9 CH4 I/O 10 NC I/O DESCRIPTION TYPE DESCRIPTION No connect Negative voltage supply rail Positive voltage supply rail 4-CHANNEL, 6-LEAD SOT23-6 PACKAGE PIN NAME TYPE ESD Channel 1 CH1 I/O No connect 2 VN GND Positive voltage supply rail 3 CH2 I/O ESD Channel ESD Channel 4 CH3 I/O ESD Channel No connect 5 VP PWR ESD Channel 6 CH4 I/O No connect Negative voltage supply rail ESD Channel No connect Rev. 4 | Page 2 of 16 | www.onsemi.com DESCRIPTION ESD Channel Negative voltage supply rail Positive voltage supply rail ESD Channel CM1293A Ordering Information PART NUMBERING INFORMATION # of Channels Leads Lead-free Finish Package 1 Ordering Part Number Part Marking 2 4 SOT143-4 CM1293A-02SR D636 2 5 SOT23-5 CM1293A-02SO D633 4 6 SOT23-6 CM1293A-04SO D635 4 10 MSOP-10 CM1293A-04MR D641 Note 1: Parts are shipped in Tape & Reel form unless otherwise specified. Specifications ABSOLUTE MAXIMUM RATINGS PARAMETER RATING UNITS 6.0 V Operating Temperature Range –40 to +85 °C Storage Temperature Range –65 to +150 °C (VN - 0.5) to (VP + 0.5) V Operating Supply Voltage (VP - VN) DC Voltage at any channel input STANDARD OPERATING CONDITIONS PARAMETER Operating Temperature Range Package Power Rating SOT143-4 Package (CM1293A-02SR) SOT23-5 Package (CM1293A-02SO) SOT23-6 Package (CM1293A-04SO) MSOP-10 Package (CM1293A-04MR) Rev. 4 | Page 3 of 16 | www.onsemi.com RATING UNITS –40 to +85 °C 225 225 225 400 mW mW mW mW CM1293A Specifications (cont’d) ELECTRICAL OPERATING CHARACTERISTICS SYMBOL PARAMETER CONDITIONS VP Operating Supply Voltage (VP-VN) IP Operating Supply Current (VP-VN)=3.3V VF Diode Forward Voltage Top Diode Bottom Diode IF = 8mA; TA=25°C ILEAK Channel Leakage Current TA=25°C; VP=5V, VN=0V CIN Channel Input Capacitance At 1 MHz, VP=3.3V, VN=0V, VIN=1.65V 1 MIN 0.60 0.60 ∆C Channel I/O to I/O capacitance VESD ESD Protection Peak Discharge Voltage at any channel input, in system Contact discharge per IEC 61000-4-2 standard TYP MAX UNITS 3.3 5.5 V 8.0 µA 0.80 0.80 0.95 0.95 V V ±0.1 ±1.0 µA 2.0 pF 1.5 pF IO VCL RDYN Notes 3 and 4; TA=25°C Channel Clamp Voltage Positive Transients Negative Transients IPP=1A, tp=8/20µs; TA=25°C; Notes 4 Dynamic Resistance Positive Transients Negative Transients IPP=1A, tp=8/20µs; TA=25°C; Notes 4 Note 1: Note 2: Note 3: Note 4: kV ±8 +9.9 –1.6 V V 0.96 0.5 Ω Ω All parameters specified at TA = –40°C to +85°C unless otherwise noted. Human Body Model per MIL-STD-883, Method 3015, CDischarge = 100pF, RDischarge = 1.5KΩ, VP = 3.3V, VN grounded. Standard IEC 61000-4-2 with CDischarge = 150pF, RDischarge = 330Ω, VP = 3.3V, VN grounded. These measurements performed with no external capacitor on VP. Rev. 4 | Page 4 of 16 | www.onsemi.com CM1293A Performance Information Input Channel Capacitance Performance Curves Rev. 4 | Page 5 of 16 | www.onsemi.com CM1293A Performance Information (cont’d) Typical Filter Performance (nominal conditions unless specified otherwise, 50 Ohm Environment) Figure 1. Insertion Loss (S21) VS. Frequency (0V DC Bias, VP=3.3V) Figure 2. Insertion Loss (S21) VS. Frequency (2.5V DC Bias, VP=3.3V) Rev. 4 | Page 6 of 16 | www.onsemi.com CM1293A Application Information Design Considerations In order to realize the maximum protection against ESD pulses, care must be taken in the PCB layout to minimize parasitic series inductances on the Supply/Ground rails as well as the signal trace segment between the signal input (typically a connector) and the ESD protection device. Refer to Figure 3, which illustrates an example of a positive ESD pulse striking an input channel. The parasitic series inductance back to the power supply is represented by L1 and L2. The voltage VCL on the line being protected is: VCL = Fwd voltage drop of D1 + VSUPPLY + L1 x d(IESD) / dt+ L2 x d(IESD) / dt where IESD is the ESD current pulse, and VSUPPLY is the positive supply voltage. An ESD current pulse can rise from zero to its peak value in a very short time. As an example, a level 4 contact discharge per the IEC61000-4-2 standard results in a current pulse that rises from zero to 30 Amps in 1ns. -9 Here d(IESD)/dt can be approximated by ∆IESD/∆t, or 30/(1x10 ). So just 10nH of series inductance (L1 and L2 combined) will lead to a 300V increment in VCL! Similarly for negative ESD pulses, parasitic series inductance from the VN pin to the ground rail will lead to drastically increased negative voltage on the line being protected. The CM1293 has an integrated Zener diode between VP and VN. This greatly reduces the effect of supply rail inductance L2 on VCL by clamping VP at the breakdown voltage of the Zener diode. However, for the lowest possible VCL, especially when VP is biased at a voltage significantly below the Zener breakdown voltage, it is recommended that a 0.22µF ceramic chip capacitor be connected between VP and the ground plane. As a general rule, the ESD Protection Array should be located as close as possible to the point of entry of expected electrostatic discharges. The power supply bypass capacitor mentioned above should be as close to the VP pin of the Protection Array as possible, with minimum PCB trace lengths to the power supply, ground planes and between the signal input and the ESD device to minimize stray series inductance. Figure 3. Application of Positive ESD Pulse between Input Channel and Ground Rev. 4 | Page 7 of 16 | www.onsemi.com CM1293A Mechanical Details SOT143 Mechanical Specifications Dimensions for CM1293A-02SR devices supplied in 4-pin SOT143 packages are presented below. PACKAGE DIMENSIONS Package SOT143 Pins 4 Dimensions Millimeters Inches Min Max Min Max A 0.80 1.22 0.031 0.048 A1 0.05 0.15 0.002 0.006 b 0.30 0.50 0.012 0.019 b2 0.76 0.89 0.030 0.035 c 0.08 0.20 0.003 0.008 D 2.80 3.04 0.110 0.119 E 2.10 2.64 0.082 0.103 E1 1.20 1.40 0.047 0.055 e 1.92 BSC 0.075 BSC e1 0.20 BSC 0.008 BSC L L1 # per tape and reel 0.4 0.6 0.54 REF 0.016 0.024 0.021 REF 3000 pieces Controlling dimension: millimeters Package Dimensions for SOT143 Rev. 4 | Page 8 of 16 | www.onsemi.com CM1293A Tape and Reel Specifications PART NUMBER PACKAGE SIZE (mm) POCKET SIZE (mm) B0 X A0 X K0 TAPE WIDTH W REEL DIAMETER QTY PER REEL P0 P1 CM1293A-02SR 2.92 X 2.37 X 1.01 2.60 X 3.15 X 1.20 8mm 178mm (7") 3000 4mm 4mm Rev. 4 | Page 9 of 16 | www.onsemi.com CM1293A Mechanical Details (cont’d) SOT23-5 Mechanical Specifications, 5 pin The 5-pin SOT23 package dimensions are presented below. PACKAGE DIMENSIONS Package SOT23-5 JEDEC No. MO-178 (Var. AA) Leads 5 Millimeters Dim. Inches Min Nom Max Min Nom Max A 1.14 1.24 1.35 0.045 0.049 0.053 A1 0.05 0.10 0.15 0.002 0.004 0.006 A2 1.09 1.14 1.19 0.043 0.045 0.047 b 0.30 0.35 0.40 0.012 0.014 0.016 c 0.08 0.15 0.22 0.003 0.006 0.009 D 2.87 2.92 2.97 0.113 0.115 0.117 E 2.67 2.79 2.92 0.105 0.110 0.115 E1 1.55 1.63 1.68 0.061 0.064 0.066 e 0.95 REF 0.037 REF e1 1.90 REF 0.075 REF L 0.35 0.40 0.45 0.014 0.016 0.018 L1 0.53 0.58 0.64 0.021 0.023 0.025 # per tape and reel 3000 pieces Package Dimensions for SOT23-5 Controlling dimension: millimeters Rev. 4 | Page 10 of 16 | www.onsemi.com CM1293A Tape and Reel Specifications PART NUMBER PACKAGE SIZE (mm) POCKET SIZE (mm) B0 X A0 X K0 TAPE WIDTH W REEL DIAMETER QTY PER REEL P0 P1 CM1293A-02SO 2.92 X 2.79 X 1.24 3.20 X 3.20 X 1.40 8mm 178mm (7") 3000 4mm 4mm Rev. 4 | Page 11 of 16 | www.onsemi.com CM1293A Mechanical Details (cont’d) SOT23-6 Mechanical Specifications The CM1293A-04SO is supplied in a 6-pin SOT23 package. Dimensions are presented below. PACKAGE DIMENSIONS Package SOT23-6 (JEDEC name is MO-178) Pins 6 Dimensions Millimeters Inches Min Max Min Max A -- 1.45 -- 0.0571 A1 0.00 0.15 0.0000 0.0059 b 0.30 0.50 0.0118 0.0197 c 0.08 0.22 0.0031 0.0087 D 2.75 3.05 0.1083 0.1201 E 2.60 3.00 0.1024 0.1181 E1 1.45 1.75 0.0571 0.0689 e 0.95 BSC 0.0374 BSC e1 1.90 BSC 0.0748 BSC L L1 # per tape and reel 0.30 0.60 0.60 REF 0.0118 0.0236 0.0236 REF 3000 pieces Package Dimensions for SOT23-6 Controlling dimension: millimeters Rev. 4 | Page 12 of 16 | www.onsemi.com CM1293A Tape and Reel Specifications PART NUMBER PACKAGE SIZE (mm) POCKET SIZE (mm) B0 X A0 X K0 TAPE WIDTH W REEL DIAMETER QTY PER REEL P0 P1 CM1293A-04SO 2.90 X 2.80 X 1.45 3.20 X 3.20 X 1.40 8mm 178mm (7") 3000 4mm 4mm Rev. 4 | Page 13 of 16 | www.onsemi.com CM1293A Mechanical Details (cont’d) MSOP-10 Mechanical Specifications The CM1293A-04MR is supplied in a 10-pin MSOP package. Dimensions are presented below. PACKAGE DIMENSIONS Package MSOP Pins 10 Dimensions Millimeters Inches Min Max Min Max A 0.75 0.95 0.028 0.038 A1 0.05 0.15 0.002 0.006 B 0.17 0.27 0.007 0.013 C 0.13 0.23 0.005 0.009 D 2.90 3.10 0.114 0.122 E 2.90 3.10 0.114 0.122 e 0.50 BSC 0.0196 BSC H 4.90 BSC 0.193 BSC L # per tape and reel 0.40 0.70 0.0137 0.029 4000 Controlling dimension: millimeters Package Dimensions for MSOP-10 Rev. 4 | Page 14 of 16 | www.onsemi.com CM1293A Tape and Reel Specifications PART NUMBER CM1293A04MR PACKAGE SIZE (mm) POCKET SIZE (mm) B0 X A0 X K0 TAPE WIDTH W REEL DIAMETER QTY PER REEL P0 P1 3.00 X 3.00 X 0.85 3.30 X 5.30 X 1.30 12mm 330mm (13") 4000 4mm 8mm Rev. 4 | Page 15 of 16 | www.onsemi.com CM1293A ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800-282-9855 Literature Distribution Center for ON Semiconductor Toll Free USA/Canada P.O. Box 5163, Denver, Colorado 80217 USA Europe, Middle East and Africa Technical Support: Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Phone: 421 33 790 2910 Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Japan Customer Focus Center For additional information, please contact your Email: [email protected] Phone: 81-3-5773-3850 local Sales Representative Rev. 4 | Page 16 of 16 | www.onsemi.com ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit