ON ESD7004 Transient voltage suppressor Datasheet

ESD7004, SZESD7004
Transient Voltage
Suppressors
Low Capacitance ESD Protection Diode
for High Speed Data Line
The ESD7004 transient voltage suppressor is designed to protect
high speed data lines from ESD. Ultra−low capacitance and low ESD
clamping voltage make this device an ideal solution for protecting
voltage sensitive high speed data lines. The flow−through style
package allows for easy PCB layout and matched trace lengths
necessary to maintain consistent impedance between high speed
differential lines such as USB 3.0 and HDMI.
Features
• Low Capacitance (0.4 pF Typical, I/O to GND)
• Protection for the Following IEC Standards:
IEC 61000−4−2 (Level 4)
• Low ESD Clamping Voltage
• SZ Prefix for Automotive and Other Applications Requiring Unique
•
Site and Control Change Requirements; AEC−Q101 Qualified and
PPAP Capable
This is a Pb−Free Device
Typical Applications
•
•
•
•
USB 3.0
HDMI
Display Port
eSATA
http://onsemi.com
MARKING
DIAGRAM
UDFN10
CASE 517BB
4M MG
G
4M
= Specific Device Code (tbd)
M
= Date Code
G
= Pb−Free Package
(*Note: Microdot may be in either location)
PIN CONFIGURATION
AND SCHEMATIC
N/C N/C
GND N/C N/C
10
9
8
7
6
1
2
3
4
5
I/O
I/O
GND
I/O
I/O
Pin 1
Pin 2
Pin 4
Pin 5
MAXIMUM RATINGS (TJ = 25°C unless otherwise noted)
Rating
Symbol
Value
Unit
Operating Junction Temperature Range
TJ
−55 to +125
°C
Storage Temperature Range
Tstg
−55 to +150
°C
Lead Solder Temperature −
Maximum (10 Seconds)
TL
260
°C
ESD
ESD
±15
±15
kV
kV
IEC 61000−4−2 Contact (ESD)
IEC 61000−4−2 Air (ESD)
Stresses exceeding Maximum Ratings may damage the device. Maximum
Ratings are stress ratings only. Functional operation above the Recommended
Operating Conditions is not implied. Extended exposure to stresses above the
Recommended Operating Conditions may affect device reliability.
See Application Note AND8308/D for further description of
survivability specs.
© Semiconductor Components Industries, LLC, 2013
December, 2013 − Rev. 4
Pins 3, 8
=
ORDERING INFORMATION
Device
Package
Shipping
ESD7004MUTAG
UDFN10
(Pb−Free)
3000 /
Tape & Reel
SZESD7004MUTAG
UDFN10
(Pb−Free)
3000 /
Tape & Reel
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
1
Publication Order Number:
ESD7004/D
ESD7004, SZESD7004
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise specified)
Parameter
Reverse Working Voltage
Breakdown Voltage
Symbol
VRWM
VBR
Conditions
Min
Typ
Max
Unit
5.0
V
I/O Pin to GND
IT = 1 mA, I/O Pin to GND
5.5
V
Reverse Leakage Current
IR
VRWM = 5 V, I/O Pin to GND
1.0
mA
Clamping Voltage (Note 1)
VC
IPP = 1 A, I/O Pin to GND (8 x 20 ms pulse)
10
V
Clamping Voltage (Note 2)
VC
IEC61000−4−2, ±8 KV Contact
Clamping Voltage
TLP (Note 3)
See Figures 6 through 9
VC
IPP = 8 A
IPP = 16 A
IPP = −8 A
IPP = −16 A
11.4
15.6
−4.5
−8.1
Junction Capacitance
CJ
VR = 0 V, f = 1 MHz between I/O Pins
0.2
0.3
pF
Junction Capacitance
CJ
VR = 0 V, f = 1 MHz between I/O Pins and GND
0.4
0.5
pF
See Figures 1 and 2
V
1. Surge current waveform per Figure 5.
2. For test procedure see Figures 3 and 4 and application note AND8307/D.
3. ANSI/ESD STM5.5.1 − Electrostatic Discharge Sensitivity Testing using Transmission Line Pulse (TLP) Model.
TLP conditions: Z0 = 50 W, tp = 100 ns, tr = 4 ns, averaging window; t1 = 30 ns to t2 = 60 ns.
Figure 1. IEC61000−4−2 +8 KV Contact ESD
Clamping Voltage
Figure 2. IEC61000−4−2 −8 KV Contact
Clamping Voltage
http://onsemi.com
2
ESD7004, SZESD7004
IEC61000−4−2 Waveform
IEC 61000−4−2 Spec.
Ipeak
Level
Test
Voltage
(kV)
First Peak
Current
(A)
Current at
30 ns (A)
Current at
60 ns (A)
1
2
7.5
4
2
2
4
15
8
4
3
6
22.5
12
6
4
8
30
16
8
100%
90%
I @ 30 ns
I @ 60 ns
10%
tP = 0.7 ns to 1 ns
Figure 3. IEC61000−4−2 Spec
ESD Gun
Oscilloscope
TVS
50 W
Cable
50 W
Figure 4. Diagram of ESD Clamping Voltage Test Setup
The following is taken from Application Note
AND8308/D − Interpretation of Datasheet Parameters
for ESD Devices.
systems such as cell phones or laptop computers it is not
clearly defined in the spec how to specify a clamping voltage
at the device level. ON Semiconductor has developed a way
to examine the entire voltage waveform across the ESD
protection diode over the time domain of an ESD pulse in the
form of an oscilloscope screenshot, which can be found on
the datasheets for all ESD protection diodes. For more
information on how ON Semiconductor creates these
screenshots and how to interpret them please refer to
AND8307/D.
ESD Voltage Clamping
For sensitive circuit elements it is important to limit the
voltage that an IC will be exposed to during an ESD event
to as low a voltage as possible. The ESD clamping voltage
is the voltage drop across the ESD protection diode during
an ESD event per the IEC61000−4−2 waveform. Since the
IEC61000−4−2 was written as a pass/fail spec for larger
% OF PEAK PULSE CURRENT
100
PEAK VALUE IRSM @ 8 ms
tr
90
PULSE WIDTH (tP) IS DEFINED
AS THAT POINT WHERE THE
PEAK CURRENT DECAY = 8 ms
80
70
60
HALF VALUE IRSM/2 @ 20 ms
50
40
30
tP
20
10
0
0
20
40
t, TIME (ms)
60
Figure 5. 8 X 20 ms Pulse Waveform
http://onsemi.com
3
80
22
−22
20
−20
18
−18
16
−16
CURRENT (A)
CURRENT (A)
ESD7004, SZESD7004
14
12
10
8
−14
−12
−10
−8
6
−6
4
−4
2
−2
0
0
0
2
4
6
8
10 12
VOLTAGE (V)
14
16
18
0
20
−2
−4
Figure 6. Positive TLP I−V Curve
−6
−8 −10 −12 −14 −16 −18 −20
VOLTAGE (V)
Figure 7. Negative TLP I−V Curve
Transmission Line Pulse (TLP) Measurement
L
Transmission Line Pulse (TLP) provides current versus
voltage (I−V) curves in which each data point is obtained
from a 100 ns long rectangular pulse from a charged
transmission line. A simplified schematic of a typical TLP
system is shown in Figure 8. TLP I−V curves of ESD
protection devices accurately demonstrate the product’s
ESD capability because the 10s of amps current levels and
under 100 ns time scale match those of an ESD event. This
is illustrated in Figure 9 where an 8 kV IEC 61000−4−2
current waveform is compared with TLP current pulses at
8 A and 16 A. A TLP I−V curve shows the voltage at which
the device turns on as well as how well the device clamps
voltage over a range of current levels. A typical TLP I−V
curve for the ESD7004 is shown in Figures 6 and 7.
S Attenuator
÷
50 W Coax
Cable
10 MW
IM
50 W Coax
Cable
VM
DUT
VC
Oscilloscope
Figure 8. Simplified Schematic of a Typical TLP
System
Figure 9. Comparison Between 8 kV IEC 61000−4−2 and 8 A and 16 A TLP Waveforms
http://onsemi.com
4
ESD7004, SZESD7004
Without ESD
With ESD7004
Figure 10. USB3.0 Eye Diagram with and without ESD7004. 5.0 Gb/s, 400 mVPP
Without ESD
With ESD7004
Figure 11. HDMI1.4 Eye Diagram with and without ESD7004. 3.4 Gb/s, 400 mVPP
With ESD7004
Without ESD
Figure 12. ESATA3.0 Eye Diagram with and without ESD7004. 6 Gb/s, 400 mVPP
http://onsemi.com
5
ESD7004, SZESD7004
DIFFERENTIAL IMPEDANCE (W)
Test Board
Region
DUT
Region
Test Board
Region
TDR max = 92.7 W
TIME (ps)
** USB spec requirement is 90 W ± 10%
Figure 13. USB TDR Measurement. 90 W Differential Impedance Target, 200 ps Rise Time
DIFFERENTIAL IMPEDANCE (W)
Test Board
Region
DUT
Region
Test Board
Region
TDR min = 97 W
TIME (ps)
** HDMI spec requirement is 100 W ± 15%
Figure 14. HDMI TDR Measurement. 100 W Differential Impedance Target, 200 ps Rise Time
http://onsemi.com
6
ESD7004, SZESD7004
S21 INSERTION LOSS (dB)
4
2
0
−2
−4
−6
−8
ESD7004 IO−GND
ESD7004 IO−IO
−10
1.E+06
1.E+07
1.E+08
1.E+09
FREQUENCY (Hz)
Figure 15. ESD7004 Insertion Loss
http://onsemi.com
7
1.E+10
ESD7004, SZESD7004
USB 3.0 Type A
Connector
StdA_SSTX+
Vbus
StdA_SSTX−
ESD7004
D−
ESD7L5.0
GND_DRAIN
D+
StdA_SSRX+
GND
StdA_SSRX−
Figure 16. USB3.0 Standard A Connector Layout Diagram
USB 3.0 Micro B
Connector
ESD7004
Vbus
D−
D+
ID
GND
ESD7004
MicB_SSTX−
MicB_SSTX+
GND_DRAIN
MicB_SSRX−
MicB_SSRX+
Figure 17. USB3.0 Micro B Connector Layout Diagram
http://onsemi.com
8
ESD7004, SZESD7004
HDMI
Type A Connector
ESD7004
D2+
GND
D2−
D1+
GND
D1−
ESD7004
D0+
GND
D0−
CLK+
GND
CLK−
CEC
N/C (or HEC_DAT – HDMI1.4)
SCL
SDA
GND
5V
HPD (and HEC_DAT – HDMI1.4)
NUP4114
Figure 18. HDMI Layout Diagram
e S ATA
Connector
GND
A+
ESD7004
A−
GND
B−
B+
GND
Figure 19. eSATA Layout Diagram
http://onsemi.com
9
ESD7004, SZESD7004
PACKAGE DIMENSIONS
UDFN10 2.5x1, 0.5P
CASE 517BB
ISSUE O
L
D
ÍÍÍ
ÍÍÍ
PIN ONE
REFERENCE
0.10 C
2X
2X
0.10 C
L1
DETAIL A
OPTIONAL
CONSTRUCTIONS
E
TOP VIEW
DETAIL B
A3
A
A1
0.08 C
A1
C
SIDE VIEW
2X
DETAIL A
b2
1
10
MOLD CMPD
EXPOSED Cu
0.10 C
10X
L
A B
10X
ÇÇÇ
ÉÉÉ
ÉÉÉ
A3
DETAIL B
DIM
A
A1
A3
b
b2
D
E
e
L
L1
MILLIMETERS
MIN
MAX
0.55
0.45
0.05
0.00
0.13 REF
0.25
0.15
0.45
0.35
2.50 BSC
1.00 BSC
0.50 BSC
0.30
0.40
--0.05
OPTIONAL
CONSTRUCTION
SEATING
PLANE
RECOMMENDED
SOLDERING FOOTPRINT*
L
10X
5
2X
0.50
6
e
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30mm FROM TERMINAL.
0.45
1.30
8X
b
0.10 C A
BOTTOM VIEW
0.05 C
PACKAGE
OUTLINE
B
NOTE 3
0.50
PITCH
8X
0.25
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
10
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
ESD7004/D
Similar pages