Inductors (Coils) > Chip Inductor (Chip Coil) > for High Frequency Horizontal Wire Wound Data Sheet Chip Inductor (Chip Coil) 1 for High Frequency Horizontal Wire Wound LQW15A_10 Series (High Q/Low DC Resistance Type) (0402 Size) ■ Packaging 0.5±0.1 1.0±0.1 0.6±0.1 0.2±0.1 Code Packaging Minimum Quantity D 180mm Paper Tape 10000 B Bulk(Bag) 500 0.10±0.05 0.5±0.1 ■ Dimensions 0.2±0.1 (in mm) ■ Rated Value (p: packaging code) Part Number Inductance Test Frequency Rated Current Max. of DC resistance Q (min.) Test Frequency Self Resonance Frequency (min.) LQW15AN1N3C10p 1.3nH±0.2nH 100MHz 1200mA 0.017ohm 20 250MHz 16.0GHz LQW15AN1N3D10p 1.3nH±0.5nH 100MHz 1200mA 0.017ohm 20 250MHz 16.0GHz LQW15AN2N2C10p 2.2nH±0.2nH 100MHz 1000mA 0.027ohm 25 250MHz 14.0GHz LQW15AN2N2D10p 2.2nH±0.5nH 100MHz 1000mA 0.027ohm 25 250MHz 14.0GHz LQW15AN2N4D10p 2.4nH±0.5nH 100MHz 1000mA 0.027ohm 25 250MHz 14.0GHz LQW15AN3N3D10p 3.3nH±0.5nH 100MHz 900mA 0.040ohm 30 250MHz 12.0GHz LQW15AN3N4C10p 3.4nH±0.2nH 100MHz 900mA 0.040ohm 30 250MHz 12.0GHz LQW15AN3N4D10p 3.4nH±0.5nH 100MHz 900mA 0.040ohm 30 250MHz 12.0GHz LQW15AN3N6C10p 3.6nH±0.2nH 100MHz 900mA 0.040ohm 30 250MHz 9.5GHz LQW15AN3N6D10p 3.6nH±0.5nH 100MHz 900mA 0.040ohm 30 250MHz 9.5GHz LQW15AN3N9D10p 3.9nH±0.5nH 100MHz 900mA 0.040ohm 30 250MHz 7.0GHz LQW15AN4N7D10p 4.7nH±0.5nH 100MHz 800mA 0.051ohm 30 250MHz 8.0GHz LQW15AN5N1C10p 5.1nH±0.2nH 100MHz 800mA 0.051ohm 30 250MHz 8.0GHz LQW15AN5N1D10p 5.1nH±0.5nH 100MHz 800mA 0.051ohm 30 250MHz 8.0GHz LQW15AN5N6C10p 5.6nH±0.2nH 100MHz 800mA 0.051ohm 30 250MHz 8.0GHz LQW15AN5N6D10p 5.6nH±0.5nH 100MHz 800mA 0.051ohm 30 250MHz 8.0GHz Operating Temperature Range: -55°C to +125°C Only for reflow soldering. Continued on the following page. o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2010.9.9 http://www.murata.com/ Inductors (Coils) > Chip Inductor (Chip Coil) > for High Frequency Horizontal Wire Wound Data Sheet 2 Continued from the preceding page. ■ Q-Frequency Characteristics (Typ.) ■ Inductance-Frequency Characteristics (Typ.) 250 10 1.3nH 5.6nH Inductance (nH) 200 150 Q 3.6nH 5.6nH 100 3.6nH 50 1.3nH 0 10 1 100 1000 10 10000 100 1000 10000 Frequency (MHz) Frequency (MHz) ■ !Caution/Notice !Caution (Rating) Do not use products beyond the rated current as this may create excessive heat. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2010.9.9 http://www.murata.com/