Features • • • • • • • • High Dynamic Range for AM and FM Integrated AGC for AM and FM High Intercept Point 3rd Order for FM FM Amplifier Adjustable to Various Cable Impedances High Intercept Point 2nd and 3rd Order for AM Low Noise Output Voltage Low Power Consumption Low Output Impedance AM 1. Description The ATR4251 is an integrated low-noise AM/FM antenna amplifier with integrated AGC in BiCMOS2S technology. The device is designed in particular for car applications, and is suitable for windshield and roof antennas. Figure 1-1. Block Diagram QFN24 Package VREF1 FM IN FM FM GAIN GND OUT AGC IN Paddle = GND 24 NC* GND AGC1 AGC2 VREF2 AMIN 23 22 21 20 19 FM amplifier 1 18 BAND GAP 2 17 AGC 3 16 4 15 5 14 AM AGC (AM) 6 7 8 9 13 10 11 Low-noise, High-dynamicrange AM/FM Antenna Amplifier IC ATR4251 NC* VS Preliminary AGCCONST VREF4 AMOUT1 GND 12 T NC* NC* CREG AGC AGC AMIN AM CONST * Pin must not be connected to any other pin or supply chain except GND. 4913E–AUDR–02/07 Figure 1-2. Block Diagram SSO20 Package FMGAIN 1 FMIN 2 VREF1 3 GND 4 AGC1 5 AGC2 6 VREF2 7 AMIN1 8 CREG 9 20 GND2 FM amplifier 19 FMOUT 18 AGCIN AGC 17 VS 16 AGCCONST Band gap 15 VREF4 14 AMOUT1 AM AGC (AM) 13 GND1 12 TCONST 11 AGCAM AGCAMIN 10 SSO20 2 ATR4251 [Preliminary] 4913E–AUDR–02/07 ATR4251 [Preliminary] 2. Pin Configuration Pinning QFN24 VREF1 FMIN FMGAIN GND FMOUT AGCIN Figure 2-1. 1 24 23 22 21 20 19 18 2 17 3 16 4 15 5 14 6 7 8 13 9 10 11 12 NC VS AGCCONST VREF4 AMOUT1 GND NC CREG AGCAMIN AGCAM TCONST NC NC GND AGC1 AGC2 VREF2 AMIN Table 2-1. Pin Description QFN24 Pin Symbol Function 1 NC 2 GND Ground FM 3 AGC1 AGC output for pin diode Pin must not be connected to any other pin or supply chain except GND. 4 AGC2 AGC output for pin diode 5 VREF2 Reference voltage for pin diode 6 AMIN AM input, impedance matching 7 NC Pin must not be connected to any other pin or supply chain except GND. 8 CREG 9 AGCAMIN AM - AGC time constant capacitance 2 10 AGCAM AM - AGC output for pin diode 11 TCONST AM - AGC - time constant capacitance 1 AM - AGC input 12 NC 13 GND Pin must not be connected to any other pin or supply chain except GND. 14 AMOUT1 15 VREF4 16 AGCCONST 17 VS Supply voltage 18 NC Pin must not be connected to any other pin or supply chain except GND. 19 AGCIN FM AGC input 20 FMOUT FM output 21 GND 22 FMGAIN 23 FMIN 24 VREF1 Paddle GND Ground AM AM output, impedance matching Bandgap FM AGC time constant Ground FM gain adjustment FM input Reference voltage 2.7V Ground Paddle 3 4913E–AUDR–02/07 Figure 2-2. Pinning SSO20 FMGAIN FMIN VREF1 GND AGC1 AGC2 VREF2 AMIN1 CREG AGCAMIN Table 2-2. 4 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 GND2 FMOUT AGCIN VS AGCCONST VREF4 AMOUT1 GND1 TCONST AGCAM Pin Description SSO20 Pin Symbol Function 1 FMGAIN FM gain adjustment 2 FMIN 3 VREF1 4 GND FM ground 5 AGC1 AGC output for PIN diode 6 AGC2 AGC output for PIN diode 7 VREF2 Reference voltage for PIN diode 8 AMIN1 AM input, impedance matching 9 CREG AM AGC constant capacitance 2 10 AGCAMIN FM input Reference voltage 2.7V AM input, AM AGC 11 AGCAM AM AGC output for PIN diode 12 TCONST AM AGC constant capacitance 1 13 GND1 14 AMOUT1 AM ground AM output, impedance matching 15 VREF4 16 AGCCONST Band gap 6V 17 VS Supply voltage 18 AGCIN FM AGC input 19 FMOUT FM output 20 GND2 FM ground FM AGC constant ATR4251 [Preliminary] 4913E–AUDR–02/07 ATR4251 [Preliminary] 3. Functional Description The ATR4251 is an integrated AM/FM antenna impedance matching circuit. It compensates cable losses between the antenna (for example windshield, roof, or bumper antennas) and the car radio which is usually placed far away from the antenna. AM refers to the long wave (LW), medium wave (MW) and short wave (SW) frequency bands (150 kHz to 30 MHz) that are usually used for AM transmission, and FM means any of the frequency bands used world-wide for FM radio broadcast (70 MHz to 110 MHz). Two separate amplifiers are used for AM and FM due to the different operating frequencies and requirements in the AM and FM band. This allows the use of separate antennas (for example, windshield antennas) for AM and FM. Of course, both amplifiers can also be connected to one antenna (for example, the roof antenna). Both amplifiers have automatic gain control (AGC) circuits in order to avoid overdriving the amplifiers under large-signal conditions. The two separate AGC circuits prevent strong AM signals from blocking FM stations, and vice versa. 3.1 AM Amplifier Due to the long wavelength in AM bands, the antennas used for AM reception in automotive applications must be short compared to the wavelength. Therefore these antennas do not provide 50Ω output impedance, but have an output impedance of some pF. If these (passive) antennas are connected to the car radio by a long cable, the capacitive load of this cable (some 100 pF) dramatically reduces the signal level at the tuner input. In order to overcome this problem, ATR4251 provides an AM buffer amplifier with low input capacitance (less than 2.5 pF) and low output impedance (5Ω). The low input capacitance of the amplifier reduces the capacitive load at the antenna, and the low impedance output driver is able to drive the capacitive load of the cable. The voltage gain of the amplifier is close to 1 (0 dB), but the insertion gain that is achieved when the buffer amplifier is inserted between antenna output and cable may be much higher (35 dB). The actual value depends, of course, on antenna and cable impedance. The input of the amplifier is connected by an external 4.7 MΩ resistor to the bias voltage (pin 7, SSO20) in order to achieve high input impedance and low noise voltage. AM tuners in car radios usually use PIN diode attenuators at their input. These PIN diode attenuators attenuate the signal by reducing the input impedance of the tuner. Therefore, a series resistor is used at the AM amplifier output in the standard application. This series resistor guarantees a well-defined source impedance for the radio tuner and protects the output of the AM amplifier from short circuit by the PIN diode attenuator in the car radio. 5 4913E–AUDR–02/07 3.2 AM AGC The IC is equipped with an AM AGC capability to prevent overdriving of the amplifier in case the amplifier operates near strong antenna signal level, for example, transmitters. The AM amplifier output AMOUT1 is applied to a resistive voltage divider. This divided signal is applied to the AGC level detector input pin AGCAMIN. The rectified signal is compared against an internal reference. The threshold of the AGC can be adjusted by adjusting the divider ratio of the external voltage divider. If the threshold is reached, pin AGCAM opens an external transistor which controls PIN diode currents and limits the antenna signal and thereby prevents overdriving the AM amplifier IC. 3.3 FM Amplifier The FM amplifier is realized with a single NPN transistor. This allows use of an amplifier configuration optimized on the requirements. For low-cost applications, the common emitter configuration provides good performance at reasonable bills of materials (BOM) cost(1). For high-end applications, common base configuration with lossless transformer feedback provides a high IP3 and a low noise figure at reasonable current consumption(2). In both configurations, gain, input, and output impedance can be adjusted by modification of external components. The temperature compensated bias voltage (VREF1) for the base of the NPN transistor is derived from an integrated band gap reference. The bias current of the FM amplifier is defined by an external resistor. Notes: 1. See test circuit (Figure 8-1 on page 11) 2. See application circuit (Figure 9-1 on page 12) 3.4 FM/TV AGC The IC is equipped with an AGC capability to prevent overdriving the amplifier in cases when the amplifier is operated with strong antenna signals (for example, near transmitters). It is possible to realize an external TV antenna amplifier with integrated AGC and external RF transistor. The bandwidth of the integrated AGC circuit is 900 MHz. FM amplifier output FMOUT is connected to a capacitive voltage divider and the divided signal is applied to the AGC level detector at pin AGCIN. This level detector input is optimized for low distortion. The rectified signal is compared against an internal reference. The threshold of the AGC can be adjusted by adjusting the divider ratio of the external voltage divider. If the threshold is reached, pin AGC1 opens an external transistor which controls the PIN diode current, this limits the amplifier input signal level and prevents overdriving the FM amplifier. 6 ATR4251 [Preliminary] 4913E–AUDR–02/07 ATR4251 [Preliminary] 4. Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Reference point is ground (pins 4 and 13 for SSO20 and pins 2, 13, 21 and Paddle for QFN24 package). Parameters Symbol Value Unit Supply voltage VS 12 V Power dissipation, Ptot at Tamb = 90°C Ptot 550 mW Tj 150 °C Ambient temperature SSO20 package Tamb –40 to +90 °C Ambient temperature QFN24 package Tamb –40 to +105 °C Storage temperature Tstg –50 to +150 °C ESD HMB All pins ±2000 V ESD MM All pins ±200 V Symbol Value Unit Junction ambient, soldered on PCB, dependent on PCB Layout for SSO 20 package RthJA 92 K/W Junction ambient, soldered on PCB, dependent on PCB Layout for QFN package RthJA 40 K/W Junction temperature 5. Thermal Resistance Parameters 6. Operating Range Parameters Symbol Min. Typ. 10 Max. Unit VS 8 11 V Ambient temperature SSO20 package Tamb –40 +90 °C Ambient temperature QFN 24 package Tamb –40 +105 °C Supply voltage 7 4913E–AUDR–02/07 7. Electrical Characteristics See Test Circuit, Figure 8-1 on page 11; VS = 10V, Tamb = 25°C, unless otherwise specified. Pin numbers in () are referred to the QFN package. No. Parameters 1.1 Supply currents 1.2 Reference voltage 1 output 1.3 1.4 2 Test Conditions Pin Symbol Min. Typ. Max. Unit Type* 17 (17) IS 10 14 17 mA A VS = 8V to 11V, T = 25°C, Ivref1 < 1.4 mA 3 (24) VRef1 2.7 2.8 2.9 V A Reference voltage 2 output VS = 8V to 11V 7 (5) VRef2 0.38 VS 0.4 VS 0.42 VS V B Reference voltage 4 output VS = 8V to 11V, Ivref4 < 5 mA 15 (15) VRef4 6.1 6.3 6.5 V A 2.7 pF D 40 nA C Ω D AM Impedance Matching 150 kHz to 30 MHz (The Frequency Response from Pin 8 to Pin 14) 2.1 Input capacitance f = 1 MHz 8 (6) 2.2 Input leakage current Tamb = 85°C 8 (6) 2.3 Output resistance 14 (14) ROUT 4 5 8 Voltage gain f = 1 MHz 8/14 (6/14) A 0.85 0.90 0.96 2.5 Output noise voltage (rms value) Pin 14 (14), R78 = 4.7 MΩ, B = 9 kHz, CANT = 30 pF 150 kHz 200 kHz 500 kHz 1 MHz –8 –9 –11 –12 –6 –7 –9 –10 dBµV dBµV dBµV dBµV C 2.6 2nd harmonic Vs = 10V, 50Ω load, fAMIN = 1 MHz, input voltage = 120 dBµV AMOUT1 –60 –58 dBc C 2.7 3rd harmonic Vs = 10V, 50Ω load, fAMIN = 1 MHz, input voltage = 120 dBµV AMOUT1 –53 –50 dBc C 2.8 2nd harmonic Vs = 8V, 50Ω load, fAMIN = 1 MHz, input voltage = 120 dBµV AMOUT1 –60 –58 dBc C 2.9 3rd harmonic Vs = 8V, 50Ω load, fAMIN = 1 MHz, input voltage = 120 dBµV AMOUT1 –53 –50 dBc C kΩ D 2.4 3 14 CAMIN 2.2 VN1 VN2 VN3 VN4 2.45 A AM AGC 3.1 Input resistance 10 (9) RAGCAMIN 40 50 3.2 Input capacitance f = 1 MHz 10 (9) CAGCAMIN 2.6 3.2 3.8 pF D 3.3 AGC input voltage threshold f = 1 MHz 10 (9) VAMth 75 77 79 dBµV B 3.4 3 dB corner frequency AGC threshold increased by 3 dB MHz D 3.5 Minimal AGCAM output ViHF = 90 dBµV at pin voltage 10 (9) V A 10 10/11 (9/10) VAGC VS – 2.1 VS – 1.9 VS – 1.7 *) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter Notes: 1. Leakage current of PIN diode can be adjusted by an external resistor between pin 11 and VS 2. Demo board measurements (see Figure 8-1 on page 11 “Common Emitter Configuration”) 3. Demo board measurements (see Figure 9-1 on page 12 “Common Base Configuration”) 8 ATR4251 [Preliminary] 4913E–AUDR–02/07 ATR4251 [Preliminary] 7. Electrical Characteristics (Continued) See Test Circuit, Figure 8-1 on page 11; VS = 10V, Tamb = 25°C, unless otherwise specified. Pin numbers in () are referred to the QFN package. No. Parameters 3.6 Test Conditions Pin Symbol Min. Typ. Maximal AGCAM output ViHF = 0V at pin 10 (9) voltage 10/11 (9/10) VAGC VS – 0.1 3.7 Maximal AGCAM output ViHF = 0V at pin 10 (9) T = +85°C voltage(1) 10/11 (9/10) VAGC 3.8 Maximum AGC sink current ViHF = 0V at pin 10 (9) U (pin 12 (11)) = 2V 12 (11) IAMsink 3.9 Transconductance of Level detector ViHF = VAMth at pin 10 (9) 10/12 (9/11) I AM sin k ------------------V AMth 3.10 IP3 at level detector input Figure 9-2 on page 13, 1 MHz and 1,1MHz, 120 dBµV 10 (9) 3.11 PIN diode current generation d(20 log IPin-diode) / dUPin12 T = 25°C, UPin12 = 2V 3.12 Output resistance 9 (8) Unit Type* VS V A VS – 0.4 VS – 0.3 V C –150 –120 µA A 20 µA ---------------mV rms C 170 dBµV D 30 dB/V D 150 ROUT Max. –90 27 35 45 kΩ D 1 (22) 1.85 1.95 2.05 V A 1 (22) 1.8 2.0 2.2 V C 35 mA D Vpp D 4 FM Amplifier 4.1 Emitter voltage 4.2 Emitter voltage 4.3 Supply current limit 4.4 Maximum output voltage VS = 10V 19 (20) 4.5 Input resistance f = 100 MHz 2 (23) RFMIN 50 Ω D 4.6 Output resistance f = 100 MHz 19 (20) RFMOUT 50 Ω D G 5 dB A T = –40°C to +85°C 19 (20) I19 12 4.7 Power gain(2) f = 100 MHz FMOUT/ FMIN 4.8 Output noise voltage (emitter circuit)(2) f = 100 MHz, B = 120 kHz 19 (20) VN –5.1 dBµV D 4.9 OIP3 (emitter circuit)(2) f = 98 + 99 MHz 19 (20) IIP3 140 dBµV C 6 dB C 2.8 dB C 148 dBµV C dBµV dBµV B B 4.10 (3) Gain (3) 4.11 Noise figure 4.12 (3) OIP3 f = 98 + 99 MHz Parameters Dependent of External Components in Application Circuit: RFMIN, RFMOUT, G, VN, IIP3 5 FM AGC 81 83 83 85 85 87 5.1 AGC threshold f = 100 MHz f = 900 MHz 18 (19) Vth1,100 Vthl,900 5.2 AGC1 output voltage AGC1 active, Vpin16 (16) = 5V 5 (24) VAGC VS – 2.1V VS – 1.9V VS – 1.7V V C 5.3 AGC1 output voltage AGC1 inactive, Vpin16 (16) = 1.7V 5 (24) VAGC VS – 0.2V V C VS *) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter Notes: 1. Leakage current of PIN diode can be adjusted by an external resistor between pin 11 and VS 2. Demo board measurements (see Figure 8-1 on page 11 “Common Emitter Configuration”) 3. Demo board measurements (see Figure 9-1 on page 12 “Common Base Configuration”) 9 4913E–AUDR–02/07 7. Electrical Characteristics (Continued) See Test Circuit, Figure 8-1 on page 11; VS = 10V, Tamb = 25°C, unless otherwise specified. Pin numbers in () are referred to the QFN package. No. Parameters Test Conditions Pin Symbol 5.4 AGC2 output voltage AGC2 active, Vpin16 (16) = 1.7V 6 (4) VAGC 5.5 AGC2 output voltage AGC2 inactive, Vpin16 (16) = 5V 6 (4) VAGC 5.6 Input resistance 18 (19) RPin18 17 21 25 kΩ D CPin18 1.5 1.75 1.9 pF D 5.7 Min. Typ. Max. Unit Type* VS – 2.1V VS – 1.9V VS – 1.7V V C VS – 0.2V V C VS Input capacitance F = 100 MHz 18 (19) 5.8 IP3 at AGC input Figure 9-2 on page 13, 100 MHz and 105 MHz, VGen = 120 dBµV 18 (19) 150 dBµV D 5.9 IP3 at AGC input 900 MHz and 920 MHz VGen = 120 dBµV 18 (19) 148 dBµV D 5.10 Max. AGC sink current ViHF = 0V 5.11 Transconductance ViHF = Vth1,100, dIPin16(16) / dUPin18(19) 5.12 Gain AGC1, AGC2 UPin16 = 3V, dUPin5(3) / dUPin16(16), –dUPin6(4) / dUPin16(16) 16 IPin16 –11 –9 –7 µA C dIPin16 / dUPin18 0.8 1.0 1.3 mA/V (rms) C 0.5 0.56 0.6 C *) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter Notes: 1. Leakage current of PIN diode can be adjusted by an external resistor between pin 11 and VS 2. Demo board measurements (see Figure 8-1 on page 11 “Common Emitter Configuration”) 3. Demo board measurements (see Figure 9-1 on page 12 “Common Base Configuration”) 10 ATR4251 [Preliminary] 4913E–AUDR–02/07 ATR4251 [Preliminary] 8. Test Circuit FM/AM Figure 8-1. Common Emitter Configuration VS 4.7Ω + 10 µF 100 nF 470 nF AMOUT1 500 pF 5 kΩ AGCIN 22Ω 2.2 nF SO20 220 nF + 55Ω 10 9 CREG 8 AMIN1 4.7 MΩ 1 µH 11 AGC (AM) AM 12 13 14 VREF2 7 Band gap 6 AGC2 AGCAM TCONST + GND1 AMOUT1 + VREF4 + AGC 4 GND 3 VREF1 FMIN FMGAIN 1 270Ω 2 2.2 nF 17 VS AGCIN 18 19 FM amplifier 20 GND2 FMOUT FMOUT 22 pF 4.7 µF 47Ω1) AGCAMIN 4.7 µF 2.2 µF 22 pF 15 150 nH AGCCONST 100 nF 5 10 µF GND 16 + AGC1 4.7Ω 1 µF 33 pF 15 nF 2.2 nF Cant 2.2 nF FMIN AMINP1 AMAGCIN 50Ω 50Ω (1) Output impedance 50Ω adjustment 11 4913E–AUDR–02/07 9. Application Circuit (Demo Board) Figure 9-1. Common Base Configuration AM/FM_OUT +VS +VS R23 C21 100 nF 2.2 µF 180 nH R24 4.7Ω + C27 10 µF GND C17 L3 C24 R11(2) 470 nF C31 33 pF 100 nF R20 R21 100Ω T2 BC858 33Ω(1) 2.2 pF (4) L3 470 nH C19 C12 100 nF C20 AM/FM application combined with AM AGC with the following capability TCONST AGC (AM) AM 12 13 GND1 AMOUT1 14 VREF4 15 AGCCONST 16 VS Band gap 1 pF 220 nF AGC FM amplifier 1 kΩ 17 AGCIN 18 19 20 GND2 FMOUT 1 pF(4) 2. Testing AM + AM AGC connector AM as input connector AM/FM_OUT as output C28 C13 4.7 µF C18 1. Testing FM + FM AGC connector FM as input connector AM/FM_OUT as output R3 R10 100Ω SO20 10 µF C30 100 nF C23 R12(2) AGCAM 4.7Ω + C26 11 VB+ 10 D3 BA779-2 BA679 BA679 C1 R7 FM 2.2 pF L1 120 nH 10 9 8 AMIN1 7 VREF2 6 AGC2 5 R6 R5 C10 100Ω (2) C7 220 nF 15 nF C4 22 pF R9 1 µF RS1 2Ω (2) 10 kΩ(3) C8 R8 5 kΩ(3) 1 nF T1 BC858 C6 10 nF C9 R4 4.7 MΩ C3 R1 47Ω R2 51Ω 100 nF 2.2 nF AGCAMIN D2 C5 AM 4 +VS D1 CREG 2.2 nF AGC1 C2 GND FMGAIN TR1 3 3 VREF1 1 2 4 2.2 nF FMIN 6 1 C29 C11 100 pF (1) AM Output impedance (50Ω adjustment) (2) Leakage current reduction (3) AM AGC threshold (4) AM AGC threshold 12 ATR4251 [Preliminary] 4913E–AUDR–02/07 ATR4251 [Preliminary] Figure 9-2. Antenna Dummy for Test Purposes OUTPUT 50Ω 1 nF 50Ω Gen AGCIN 13 4913E–AUDR–02/07 10. Internal Circuitry Table 10-1. PIN SSO20 Equivalent Pin Circuits (ESD Protection Circuits Not Shown) PIN QFN24 Symbol Equivalent Circuit 19 1 2 19 22 23 20 FMGAIN FMIN FMOU 1 2 3 24 VREF1 3 4, 13, 20 2, 13, 21 GND VS 5 6 7 14 3 4 AGC1 AGC2 1, 7, 12, 18 NC 5 VREF2 5 7 ATR4251 [Preliminary] 4913E–AUDR–02/07 ATR4251 [Preliminary] Table 10-1. Equivalent Pin Circuits (ESD Protection Circuits Not Shown) (Continued) PIN SSO20 PIN QFN24 Symbol Equivalent Circuit VS 8 6 AMIN1 8 9 8 CREG 9 10 10 9 AGCAMIN 11 10 AGCAM 11 15 4913E–AUDR–02/07 Table 10-1. Equivalent Pin Circuits (ESD Protection Circuits Not Shown) (Continued) PIN SSO20 PIN QFN24 Symbol 12 11 TCONS Equivalent Circuit 12 14 14 AMOUT1 15 15 VREF4 16 16 AGCCONST 17 17 VS 14 15 16 16 ATR4251 [Preliminary] 4913E–AUDR–02/07 ATR4251 [Preliminary] Table 10-1. Equivalent Pin Circuits (ESD Protection Circuits Not Shown) (Continued) PIN SSO20 PIN QFN24 Symbol 18 19 AGCIN Equivalent Circuit 18 17 4913E–AUDR–02/07 11. Ordering Information Extended Type Number Package Remarks ATR4251-TKSY SSO20 Sticks ATR4251-TKQY SSO20 Taped and reeled ATR4251-PFSY QFN24, 4 mm × 4 mm Sticks ATR4251-PFQY QFN24, 4 mm × 4 mm Taped and reeled 12. Package Information Figure 12-1. SSO20 5.4±0.2 1.3±0.05 0.05+0.1 0.25±0.05 6.45±0.15 0.65±0.05 0.15±0.05 4.4±0.1 6.75-0.25 5.85±0.05 20 11 Package: SSO20 Dimensions in mm technical drawings according to DIN specifications 1 10 Drawing-No.: 6.543-5056.01-4 Issue: 1; 10.03.04 18 ATR4251 [Preliminary] 4913E–AUDR–02/07 ATR4251 [Preliminary] Figure 12-2. QFN24 Package: QFN 24 - 4 x 4 Exposed pad 2.15 x 2.15 (acc. JEDEC OUTLINE No. MO-220) Dimensions in mm 4 0.9±0.1 2.15±0.15 24 19 1 24 18 1 13 0.4±0.1 0.23±0.07 6 6 12 technical drawings according to DIN specifications 7 0.5 nom. Drawing-No.: 6.543-5086.01-4 Issue: 2; 24.01.03 13. Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. History 4913E-AUDR-02/07 • • • • • • • • Put datasheet in a new template Figure 1-1 exchanged with figure 1-2 on pages 1 to 2 Figure 2-1 exchanged with figure 2-2 on pages 3 to 4 Table 2-1 exchanged with table 2-2 on pages 3 to 4 Section 3.1 “AM Amplifier” on page 5 changed Section 3.4 “FM AGC” on page 6 renamed in “FM/TV AGC” and changed Section 7 “Electrical Characteristics” on pages 8 to 10 changed Figure 9-1 “Common Base Configuration” on page 12 changed 19 4913E–AUDR–02/07 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-47-50 Fax: (33) 4-76-58-47-60 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2007 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, Everywhere You Are® and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 4913E–AUDR–02/07