PD - 91552C POWER MOSFET SURFACE MOUNT(SMD-1) Product Summary IRFN440 JANTX2N7222U JANTXV2N7222U REF:MIL-PRF-19500/596 500V, N-CHANNEL ® HEXFET MOSFET TECHNOLOGY Part Number RDS(on) ID IRFN440 0.85 Ω 8.0A HEXFET® MOSFET technology is the key to International Rectifier’s advanced line of power MOSFET transistors. The efficient geometry design achieves very low on-state resistance combined with high transconductance. HEXFET transistors also feature all of the well-established advantages of MOSFETs, such as voltage control, very fast switching, ease of paralleling and electrical parameter temperature stability. They are well-suited for applications such as switching power supplies, motor controls, inverters, choppers, audio amplifiers, high energy pulse circuits, and virtually any application where high reliability is required. The HEXFET transistor’s totally isolated package eliminates the need for additional isolating material between the device and the heatsink. This improves thermal efficiency and reduces drain capacitance. SMD-1 Features: n n n n n n n Simple Drive Requirements Ease of Paralleling Hermetically Sealed Electrically Isolated Surface Mount Dynamic dv/dt Rating Light-weight Absolute Maximum Ratings Parameter ID @ VGS = 10V, TC = 25°C ID @ VGS = 10V, TC = 100°C IDM PD @ TC = 25°C VGS EAS IAR EAR dv/dt TJ T STG Continuous Drain Current Continuous Drain Current Pulsed Drain Current ➀ Max. Power Dissipation Linear Derating Factor Gate-to-Source Voltage Single Pulse Avalanche Energy ➁ Avalanche Current ➀ Repetitive Avalanche Energy ➀ Peak Diode Recovery dv/dt ➂ Operating Junction Storage Temperature Range Package Mounting Surface Temperature Weight Units 8.0 5.0 32 125 1.0 ±20 700 8.0 12.5 3.5 -55 to 150 A W W/°C V mJ A mJ V/ns o 300(for 5 seconds) 2.6 (Typical) C g For footnotes refer to the last page www.irf.com 1 1/28/02 IRFN440 Electrical Characteristics @ Tj = 25°C (Unless Otherwise Specified) Parameter Min Typ Max Units Test Conditions BVDSS Drain-to-Source Breakdown Voltage ∆BV DSS/∆T J Temperature Coefficient of Breakdown Voltage RDS(on) Static Drain-to-Source On-State Resistance VGS(th) Gate Threshold Voltage gfs Forward Transconductance IDSS Zero Gate Voltage Drain Current 500 — — V VGS = 0V, ID = 1.0mA — 0.78 — V/°C Reference to 25°C, ID = 1.0mA — — 2.0 4.7 — — — — — — — — 0.85 0.95 4.0 — 25 250 Ω IGSS IGSS Qg Q gs Q gd td(on) tr td(off) tf LS + LD Gate-to-Source Leakage Forward Gate-to-Source Leakage Reverse Total Gate Charge Gate-to-Source Charge Gate-to-Drain (‘Miller’) Charge Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Total Inductance — — — — — — — — — — — — — — — — — — — 4.0 100 -100 68.5 12.5 42.4 21 73 72 51 — Ciss C oss C rss Input Capacitance Output Capacitance Reverse Transfer Capacitance — — — 1300 310 120 — — — VGS = 10V, ID = 5.0A ➃ VGS = 10V, ID = 8.0A VDS = VGS, ID = 250µA VDS > 15V, IDS = 5.0A ➃ VDS= 400V ,VGS=0V VDS = 400V, VGS = 0V, TJ = 125°C VGS = 20V VGS = -20V VGS =10V, ID = 8.0A VDS =250V V S( ) Ω µA nA nC VDD = 250V, ID = 8.0A, VGS =10V, RG = 9.1Ω ns nH pF Measured from the center of drain pad to center of source pad. VGS = 0V, VDS = 25V f = 1.0MHz Source-Drain Diode Ratings and Characteristics Parameter Min Typ Max Units IS ISM VSD t rr Q RR Continuous Source Current (Body Diode) Pulse Source Current (Body Diode) ➀ Diode Forward Voltage Reverse Recovery Time Reverse Recovery Charge ton Forward Turn-On Time — — — — — — — — — — 8.0 32 1.5 700 8.9 Test Conditions A V nS µC Tj = 25°C, IS = 8.0A, VGS = 0V ➃ Tj = 25°C, IF = 8.0A, di/dt ≤ 100A/µs VDD ≤ 30V ➃ Intrinsic turn-on time is negligible. Turn-on speed is substantially controlled by LS + LD. Thermal Resistance Parameter RthJC RthJ-PCB Junction-to-Case Junction-to-PC board Min Typ Max Units — — — 4.0 1.0 — °C/W Test Conditions Soldered to a copper-clad PC board Note: Corresponding Spice and Saber models are available on the G&S Website. For footnotes refer to the last page 2 www.irf.com IRFN440 Fig 1. Typical Output Characteristics Fig 2. Typical Output Characteristics Fig 3. Typical Transfer Characteristics Fig 4. Normalized On-Resistance Vs. Temperature www.irf.com 3 IRFN440 1 13a & b Fig 5. Typical Capacitance Vs. Drain-to-Source Voltage Fig 7. Typical Source-Drain Diode Forward Voltage 4 Fig 6. Typical Gate Charge Vs. Gate-to-Source Voltage Fig 8. Maximum Safe Operating Area www.irf.com IRFN440 V DS VGS RD D.U.T. RG + -V DD 10V Pulse Width ≤ 1 µs Duty Factor ≤ 0.1 % Fig 10a. Switching Time Test Circuit VDS 90% 10% VGS Fig 9. Maximum Drain Current Vs. Case Temperature td(on) tr t d(off) tf Fig 10b. Switching Time Waveforms Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case www.irf.com 5 IRFN440 15V L VDS D .U .T . RG IA S 20V 10 D R IV E R + - VD D A 0 .01 Ω tp Fig 12a. Unclamped Inductive Test Circuit V (B R )D S S tp Fig 12c. Maximum Avalanche Energy Vs. Drain Current IAS Current Regulator Same Type as D.U.T. Fig 12b. Unclamped Inductive Waveforms 50KΩ QG 10 12V .2µF .3µF 10 V QGS QGD + V - DS VGS VG 3mA Charge Fig 13a. Basic Gate Charge Waveform 6 D.U.T. IG ID Current Sampling Resistors Fig 13b. Gate Charge Test Circuit www.irf.com IRFN440 Footnotes: ➀ Repetitive Rating; Pulse width limited by ➂ ISD ≤ 8.0A, di/dt ≤ 100A/µs, maximum junction temperature. ➁ VDD = 25V, starting TJ = 25°C, L= 10.4mH Peak IL = 8.0A, VGS = 10V ➃ Pulse width ≤ 300 µs; Duty Cycle ≤ 2% VDD ≤ 500V, TJ ≤ 150°C Case Outline and Dimensions — SMD-1 PAD ASSIGNMENTS 1- DRAIN 2- GATE 3- SOURCE IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information. Data and specifications subject to change without notice. 01/02 www.irf.com 7