ECE80 Series AC-DC Power Supplies 80 Watts • Ultra Compact Size • Single Outputs from 12 to 48 V • Encapsulated • PCB, Chassis Mount and DIN Rail Versions • <0.3 W No Load Input Power • -40 to +70 °C Operation • Peak Load Capability • 3 Year Warranty Dimensions: The ECE80 series of compact encapsulated AC-DC power modules are available in both PCB & chassis mount versions offering exceptional power density of >11W/in3. Output voltages are available from 12 – 48 VDC and these “green power” modules offer high active mode efficiency and low no load power consumption. They also provide a peak load capability up to 130% of nominal power for up to 30s and a wide operating temperature range from -40 to +70°C. ECE80: 3.60 x 1.80 x 1.10” (91.4 x 45.72 x 28.0 mm) ECE80-S: 4.45 x 1.87 x 1.12” (113.0 x 47.5 x 28.5 mm) Models & Ratings Output Power Output Current Output Voltage Nominal Peak (1) Efficiency (4) Model Number 80 W 12.0 V 6.67 A 8.67 A 88% ECE80US12 80 W 15.0 V 5.33 A 6.93 A 88% ECE80US15 80 W 24.0 V 3.33 A 4.33 A 87% ECE80US24 80 W 36.0 V 2.22 A 2.89 A 87% ECE80US36 80 W 48.0 V 1.67 A 2.17 A 87% ECE80US48 (2,3) Notes 1. Peak load lasting <30 s with a maximum duty cycle of 10%, average output power not to exceed nominal power. 2. Add suffix -S to model number to denote chassis mount with screw terminal type, e.g. ECE80US12-S. 3. A screw terminal version (-S) is available with DIN Clip attached. Add suffix ‘D’, e.g. ECE80US24-SD. DIN Rail mounting clip is available as a separate item, order code ECE80 DIN CLIP. 4. Average of efficiencies measured at 25%, 50%, 75% & 100% load with 230 VAC input. Summary Characteristic Input Range Minimum Typical 85 No Load Input Power 1 Efficiency 86 Operating Temperature -40 87 Maximum Units Notes & Conditions 264 VAC Derate load from 100% at 90 VAC to 90% at 85 VAC <0.3 W <0.5 W 48 V version 88 % See note 4 above +70 °C Some specification parameters may not met below -25 °C. Derate linearly from 100% load at +50 °C to 50% load at 70 °C. EMC EN55022 & 32 Level B Conducted & Radiated, EN61000-4, EN61000-3 Safety Approvals EN60950-1, UL60950-1, CSA22.2 No. 234 per cUL www.xppower.com 12-36 V versions ECE80 Series AC-DC Power Supplies Input Maximum Units Notes & Conditions Input Voltage - Operating 85 264 VAC Derate load from 100% at 90 VAC to 90% at 85 VAC Input Frequency 47 63 Hz Characteristic Minimum Typical Power Factor EN61000-3-2 class A compliant Input Current 1.4/0.87 No Load Input Power Inrush Current A rms At 115/230 VAC 0.3 W 12-36 V versions 0.5 W 48 V version A 115/230 VAC cold start at 25 °C 60/120 Earth Leakage Current Input Protection Class II construction no earth Internal T3.15 A/250 VAC fuse Output Characteristic Minimum Output Voltage 12 Typical Initial Set Accuracy Minimum Load Maximum Units Notes & Conditions 48 VDC See Models and Ratings table 1 % At 100% load A No minimum load required 0 Start Up Delay 0.5 s Start Up Rise Time 30 ms Hold Up Time 8.4 15 ms At full load and 115 VAC Line Regulation ±0.5 % Load Regulation ±1 % Transient Response 4 % Recovery within 1% in less than 500 µs for a 25% load change For ECE80/ECE80-S, 20 MHz bandwidth 1/2 % pk-pk Overvoltage Protection Ripple & Noise 115 140 % Vnom Overload Protection 110 185 % 0.02 %/˚C Short Circuit Protection Trip & restart (hiccup mode) Temperature Coefficient General Characteristic Minimum Typical Maximum Units Efficiency 86 87 88 % Isolation 3000 Switching Frequency VAC 65 Power Density Weight See Models & Ratings table Input to Output kHz 11.2 Mean Time Between Failure Notes & Conditions W/in3 >300 kHrs MIL-HDBK-217F, +25 °C GB 0.66 (260) lb (g) ECE80 0.71 (280) lb (g) ECE80-S Maximum Units Notes & Conditions Environmental Characteristic Minimum Typical Operating Temperature -40 +70 °C Storage Temperature -40 +85 °C 95 %RH 3048 m Cooling Humidity Operating Altitude Vibration Some specification parameters may not met below -25 °C. Derate linearly from 100% load at +50 °C to 50% load at 70 °C. Convection-cooled Non-condensing 2 g, 10 Hz to 500 Hz, 10 mins/cycle, 60 mins each cycle www.xppower.com 2 ECE80 Series AC-DC Power Supplies EMC: Emissions Phenomenon Test Level Standard Conducted EN55022/55032 Class B Radiated EN55022/55032 Class B Harmonic Current EN61000-3-2 Voltage Flicker EN61000-3-3 Criteria Notes & Conditions Class A EMC: Immunity Test Level Criteria EN61000-4-2 ±6 kV/±8 kV A Radiated EN61000-4-3 10 V/m 80% mod A EFT EN61000-4-4 3 A Phenomenon Standard ESD Surges EN61000-4-5 2 A Conducted EN61000-4-6 3 A Magnetic Fields EN61000-4-8 3 A EN61000-4-11 DIP: >95% 10 ms DIP: 30% 500 ms INT: >95% 5000 ms A A B Dips and Interruptions Notes & Conditions Contact/Air Discharge At 100 VAC and 230 VAC Safety Approvals Safety Agency Safety Standard UL UL60950-1, CSA 22.2 No.234 per cUL Notes & Conditions TUV EN60950-1 CB IEC60950-1 Mechanical Details ECE80 ECE80 Screw Terminal (-S) 0.139 (3.54) 3.60 (91.4) ACL 1.80 (45.7) 1.18 (30.0) 0.50 (12.7) 0.18 (4.5) 4x ø0.14 (4x ø3.5) 0.44 (11.2) +Vo TOP VIEW 4.09 (104.0) ACN -Vo 1.87 (47.5) 0.159 (4.05) +Vo TOP VIEW ACL -Vo 0.84 (21.3) 1.50 (38.1) ACN 0.14 (3.55) 3.32 (84.3) 3.50 (89.7) 0.54 (13.8) 1.10 (28.0) 0.20 (4.7) 1º 1.12 (28.5) 4x ø 0.06 (ø1.5) 0.24 (6.2) 0.4 (10.2) 0.10 (2.5) 4.45 (113.0) Optional DIN clip 0.58 (14.73) 1.38 (35.0) Notes 1. All dimensions in inches (mm). 2. Weight: ECE80: 0.66 lbs (260 g) ECE80-S: 0.71 lbs (270 g) 3. Tolerances: x.xx = ± 0.02 (x.x = ± 0.5), x.xxx = ± 0.01 (x.xx = ± 0.25) 3 www.xppower.com 20 Dec 16