ES1A-ES1J 1.0 AMPS. Surface Mount Super Fast Rectifiers SMA/DO-214AC Features Glass passivated junction chip For surface mounted application Low profile package Built-in strain relief, Ideal for automated placement Easy pick and place Super fast recovery time for high efficiency Glass passivated chip junction High temperature soldering: O 260 C/10 seconds at terminals Plastic material used carries Underwriters Laboratory Classification 94V-0 Mechanical Data Cases: Molded plastic Terminals: Pure tin plated, lead free. Polarity: Indicated by cathode band Packing: 12mm tape Weight: 0.064 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 OC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol ES ES ES ES ES ES ES ES Type Number Units 1A 1B 1C 1D 1F 1G 1H 1J Maximum Recurrent Peak Reverse Voltage V VRRM 50 100 150 200 300 400 500 600 35 70 105 140 210 280 350 420 Maximum RMS Voltage V VRMS Maximum DC Blocking Voltage VDC Maximum Average Forward Rectified Current See Fig. 1 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.0A 50 100 150 200 300 400 500 600 I(AV) 1.0 A IFSM 30 A VF 0.95 1.3 o Maximum DC Reverse Current @ TA =25 C o at Rated DC Blocking Voltage @ TA=100 C IR Maximum Reverse Recovery Time ( Note 1 ) Trr Typical Junction Capacitance ( Note 2 ) Maximum Thermal Resistance (Note 3) Operating Temperature Range Cj RθJA RθJL TJ 1.7 V 5.0 100 35 10 uA uA nS pF 8 85 35 -55 to +150 -55 to +150 Storage Temperature Range TSTG 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A Notes: 2. Measured at 1 MHz and Applied VR=4.0 Volts 3. P.C.B. Mounted on 0.2 x 0.2” (5.0 x 5.0mm) Copper Pad Area. http://www.luguang.cn V mail:[email protected] o C /W o C C o ES1A-ES1J 1.0 AMPS. Surface Mount Super Fast Rectifiers RATINGS AND CHARACTERISTIC CURVES (ES1A THRU ES1J) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 50 1.2 0 80 90 100 110 120 130 140 150 o LEAD TEMPERATURE. ( C) -D 1G 1A ES 1F -1 J 0.2 1 1H 0.4 ES 0.6 10 ES RESISTIVE OR INDUCTIVE LOAD 0.2X0.2"(5.0X5.0mm) COPPER PAD AREAS 0.8 INSTANTANEOUS FORWARD CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 0 Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 1.0 0.1 30 8.3ms Single Half Sine Wave o (JEDEC Method) at TL=120 C 25 0.01 0.4 0.8 1.0 1.2 1.4 1.6 1.8 20 15 10 FIG.5- TYPICAL REVERSE CHARACTERISTICS 1000 5.0 100 10 1 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE 14 JUNCTION CAPACITANCE.(pF) 0.6 FORWARD VOLTAGE. (V) Tj=25 0C f=1.0MHz Vsig=50mVp-p 12 ES1 10 ES 8.0 1F A- D -J 6.0 INSTANTANEOUS REVERSE CURRENT. ( A) PEAK FORWARD SURGE CURRENT. (A) FIG.3- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 100 Tj=125 0C 10 Tj=85 0C Tj=25 0C 0.1 4.0 2.0 0 1 0 0.01 100 10 0 REVERSE VOLTAGE. (V) 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: B07 http://www.luguang.cn mail:[email protected]