Rohm BH76809FVM-TR Output capacitor-less video driver Datasheet

Composite Video Amplifier
Output Capacitor-less
Video Drivers
No.14064EBT02
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
●Description
The BH768xxFVM series video drivers are the optimum solution for high density integration systems such as, digital still
cameras, mobile phones, and portable video devices. A built-in charge pump circuit eliminates the need for a large output
coupling capacitor. Features include: a built-in LPF, low-voltage (2.5 V) operation, and 0 µA current consumption during
standby mode.
●Features
1)
Select from four video driver amp gain settings: 6 dB, 9 dB, 12 dB, and 16.5 dB
2)
Large-output video driver with maximum output voltage of 5.2 VP-P
Supports wide and low-voltage operation range.
3)
No output coupling capacitor is needed, which makes for a more compact design
4)
Built-in standby function sets circuit current to 0 µA (typ.) during standby mode
5)
Clear image reproduction by on-chip 8-order 4.5-MHz LPF (Low Pass Filter)
6)
Bias input method is used to support chroma, video, and RGB signals.
7)
MSOP8 compact package
●Applications
Mobile telephones, DSCs (digital still cameras), DVCs (digital video cameras), portable game systems,
portable media players, etc.
●Line up matrix
Part No.
Video driver amp gain
Recommended input level
BH76806FVM
6dB
1 VP-P
BH76809FVM
9dB
0.7 VP-P
BH76812FVM
12dB
0.5 VP-P
BH76816FVM
16.5dB
0.3 VP-P
●Absolute maximum ratings
（Ta=25℃）
Parameter
Symbol
Ratings
Unit
VCC
3.55
V
Pd
0.47
W
Operating temperature range
Topr
-40 to +85
℃
Storage temperature range
Tstg
-55 to +125
℃
Supply voltage
Power dissipation
＊ Reduce by 4.7 mW/C over 25C, when mounted on a 70mm×70mm×1.6mm PCB board.
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
1/16
2014.08 - Rev.B
Technical Note
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
●Operating range (Ta=25℃)
Parameter
Symbol
Min.
TYP.
Max.
Unit
Supply voltage
VCC
2.5
3.0
3.45
V
●Electrical characteristics (Unless otherwise noted, Typ.: Ta=25℃, VCC=3V)
Typical value
Parameter
Symbol
Circuit current 1
ICC1
Circuit current 2
ICC2
Standby SW input current
High-Level
BH76806
FVM
BH76809
FVM
BH76812
FVM
16
BH76816
FVM
Conditions
mA
No signal
0.0
μA
Standby mode
IthH
45
μA
When 3.0 V is applied to 4pin
Standby switching voltage
High-Level
VthH
(min.) 1.2
V
standby OFF
Standby Switching voltage
Low-Level
VthL
(max.) 0.45
V
standby ON
Video driver amp gain
GV
dB
Vo=100kHz, 1.0VP-P
Maximum output level
Vomv
5.2
VP-P
f=1kHz,THD=1%
Frequency characteristic 1
Gf1
-0.45
dB
f=4.5MHz/100kHz
Frequency characteristic 2
Gf2
-3.0
dB
f=8.0MHz/100kHz
Frequency characteristic 3
Gf3
-32
dB
f=18MHz/100kHz
Frequency characteristic 4
Gf4
-51
dB
f=23.5MHz/100kHz
Differential Gain
DG
0.5
%
Vo =1.0VP-P
Standard stair step signal
Differential Phase
DP
1.0
deg
Vo =1.0VP-P
Standard stair step signal
6.0
15
Unit
9.0
12.0
16.5
Band = 100k to 6MHz
75 Ω termination
100% chroma video signal
Band = 100 to 500kHz
75Ωtermination
100%chroma video signal
Band = 100 to 500kHz
75Ωtermination
100%chroma video signal
Y signal output S/N
SNY
+74
+73
+70
+70
dB
C signal output S/N (AM)
SNCA
+77
+76
+75
+75
dB
C signal output S/N (PM)
SNCP
+65
dB
Output pin source current
lextin
30
mA
4.5 V applied via 150 Ω to
output pin
Output DC offset voltage
Voff
(max.) ±50
mV
75 Ω termination
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2/16
2014.08 - Rev.B
Technical Note
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
●Measurement circuit
1µ
1
8
IN
1
V2
(VCC)
A
SW2
OUT
CHARGE PUMP
2
7
2
10µ
GND
0.1µ
3
V
6dB/9dB/12dB/16.5dB
LPF
6
+
0.1µ
OSC1
1µ
NVCC
150k
50
-
4.7µ
4
V4
75
5
V
※
75
Test circuit is intended for shipment inspections, and differs from application circuit.
Fig. 1
●Control pin settings
Parameter
Standby control
States
Note
STBY(4pin)=H
STBY:OFF
STBY(4pin)=L
STBY:ON
STBY(4pin)=OPEN
STBY:ON
●Block diagram
C1 1
8 C2
IN
CHARGE PUMP
OUT
VCC 2
7 NVCC
NVCC
GND
VIN 3
LPF
6dB/9dB/12dB/16.5dB
+
6 GND
150k
-
STBY
4
5 VOUT
Fig. 2
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
3/16
2014.08 - Rev.B
Technical Note
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
●Pin descriptions
Pin
No.
Pin
name
DC
voltage
equivalent circuit
Functions
Flying capacitor "+" pin
1
C1
+VCC
↑↓
0V
See function description for pins 7
and 8
2
VCC
VCC
VCC Pin
Video signal input pin
VIN
3
VIN
1µF
0V
150k
Adaptive input signal
Composite video signal/
chroma signal/RGB signal, etc.
4
VCC
to
0V
STBY
STANBY control Pin
Terminal
MODE
Voltage
1.2V to VCC
STBY:OFF
(H)
0V to 0.45V
STBY:ON
(L)
Video signal output pin
5
VOUT
0V
VOUT
75Ω
6
＊1
＊2
GND
0V
75Ω
GND Pin
The DC voltage in the figure is VCC = 3.0 V. These values are for reference only and are not guaranteed.
These values are for reference only and are not guaranteed.
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
4/16
2014.08 - Rev.B
Technical Note
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
●Pin descriptions
Flying capacitor “-”pin
(8pin)
7
VCC
C1
-VCC
(-2.75V)
NVCC
0V
C2
8
0V
↑↓
-VCC
(-2.75V)
C2
NVCC
NVCC
Load voltage pins (7 pins)
＊1
＊2
The DC voltage in the figure is VCC = 3.0 V. These values are for reference only and are not guaranteed.
These values are for reference only and are not guaranteed.
●Description of operations
1)
Principles of video driver with no output coupling capacitor
Amp (Single power supply)
VCC
Amp (Dual power supply)
Output capacitor is required due to DC
VCC
voltage at output pin
DC voltage is not applied to output pin
75Ω
1000µF
Output capacitor is not required since
75Ω
75Ω
75Ω
-VCC
1/2VCC Bias
Fig.3
Fig.4
When the amplifier operates using single voltage power supply, the operating potential point is approximately 1/2 Vcc.
Therefore, a coupling capacitor is required to prevent DC output. For the video driver, the load resistance is 150 Ω (75 Ω
+ 75 Ω). Therefore, the coupling capacitor should be about 1000 µF when a low bandwidth for transmission is considered.
(See Figure 3.)
When the amplifier operates using a dual (±) power supply, the operating point can be set at GND level, and therefore,
there is no need for a coupling capacitor to prevent DC output.
Since a coupling capacitor is not needed, there is no sagging of low-frequency characteristics in output stage. (See Figure
4.)
2)
Generation of negative voltage by charge pump circuit
As is shown in Figure 5, the charge pump consists of a pair of switches (SW1 and SW2) and a pair of capacitors (flying
capacitor and load capacitor), generating a negative voltage. When +3 V is applied to this IC, approximately -2.83 V of
negative voltage is obtained.
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
5/16
2014.08 - Rev.B
Technical Note
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
Vcc +3V
Vcc +3V
charge current
charge current
SW1
SW2
-Vcc is generated
SW1
SW2
Flying capacitor
charge current
Load capacitor
Load capacitor
Flying capacitor
charge transfer mode
Vcc +3V
charge current
-Vcc is generated
Fig. 5
1)
Principles of Charge Pump Circuit
Configuration of BH768xxFVM Series
As is shown in Figure 6, in the BH768xxFVM Series, a dual power supply amplifier is integrated with a charge pump circuit
in the same IC. This enables operation using a +3V single power supply while also using a dual power supply amplifier,
which eliminates the need for an output coupling capacitor.
Vcc
3.3uF
1µF
VIDEO
AMP
LPF
75Ω
75Ω
CHARGE
PUMP
1µF
1µF
Fig. 6 BH768xxFVM Configuration Diagram
2)
Input terminal type and sag characteristics
BH768xxFVM Series devices provide both a low-voltage video driver and a large dynamic range (approximately 5.2 VP-P).
A resistance termination method (150 kΩ termination) is used instead of the clamp method, which only supports video
signals, since it supports various signal types.
The BH768xxFVM series supports a wide range of devices such as, video signals, chroma signals, and RGB signals that
can operate normally even without a synchronization signal.
In addition, input terminating resistance (150 kΩ) can use a small input capacitor without reducing the sag low-band
It is recommended to use a H-bar signal when evaluating sag characteristics, since it makes sag more noticeable. (See
Figures 7 to 10.)
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
6/16
2014.08 - Rev.B
Technical Note
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
Sag is determined
by input capacitor
and input
resistance only.
Cut-off frequency for input capacitor and input impedance is
the same as when the output capacitor is set at 1000 µF with
an ordinary 75 Ω driver.
1 μF X 150 KΩ = 1000 μF X 150 Ω
(Input terminal time constant) (Output terminal time constant)
1µF
150k
Sag
Fig. 7
a) Sag-free TV Test Signal Generator Output(Sibasoku TG-7/1 , H-bar)
H-bar signal's TV screen
output image
Fig. 8
b) BH768xxFVM output (input = 1.0 µF, output, H-bar)
VCC
TG-7/1
150k
1μF
Monitor
75Ω
75Ω
-VCC
BH768xxFVM
Fig. 9
Nearly identical sag characteristics
c) 1000 µF + 150 Ω sag waveform
(TV Test Signal Generator Sibasoku TG-7/1 output, H-bar)
Monitor
75Ω
1000μF
75Ω
TG-7/1
Fig. 10
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
7/16
2014.08 - Rev.B
Technical Note
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
●Application circuit
1.0µF
(C18)
1
8
IN
※
10Ω(R2)
OUT
CHARGE PUMP
2
7
3.3µF
(C2)
VIDEO IN
3
1.0µF(C3)
1.0µF(C7)
NVCC
GND
6dB/9dB/12dB/16.5dB
LPF
6
+
150k
-
75Ω(R5)
4
5
Although ROHM is confident that the example application circuit reflects the best possible
recommendations, be sure to verify circuit characteristics for your particular application.
Fig. 11
※
A large current transition occurs in the power supply pin when the charge pump circuit is switched.
If this affects other ICs (via the power supply line), insert a resistor (approximately 10 Ω) in the
VCC line to improve the power supply's ripple effects. Although inserting a 10 Ω resistor lowers
the voltage by about 0.2 V, this IC has a wide margin for low-voltage operation, so dynamic range
problems or other problems should not occur.
●The effect of the resister inserted in the VCC line
Vcc
1.Effects of charge pump
circuit’s current ripple
Vcc端子
3.3µF
2.Current ripple affects DAC, etc.
1µF
1µF
DAC etc
VIDEO
AMP
LPF
75Ω
75Ω
CHARGE
PUMP
1µF
1µF
Fig. 12
Effect of Charge Pump Circuit's Current Ripple on External Circuit
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
8/16
2014.08 - Rev.B
Technical Note
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
1) Decoupling capacitor only
Current waveform (A)
between single power supply and C2
10mA/div
Vcc
Current waveform (B)
between C2 and IC
10mA/div
A
C2
A
(B)
VCC
Fig.13
2) Decoupling capacitor + Resistance 10Ω
(A)
Current waveform (A)
between single power supply and R2
10mA/div
Current waveform (B)
between R2 and C2
10mA/div
Current waveform (C)
between single power supply and C2
10mA/div
Vcc
10Ω
C2 (B)
A
A
A
R2
(A)
(C)
Fig.14
VCC
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
9/16
2014.08 - Rev.B
Technical Note
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
●Pattern diagram of evaluation board
SW
STBY
ACT
GND
VIN
R2
GND
R3
VOUT
R1
C4
C3
C2
CN1
CN2
VCC
C1
GND
GND
GND
GND
GND
ROHM
●List of external components
Symbol
BH76806/09/12/16FVM
Fig. 15
Function
Recommended
value
Remark
C1
Flying capacitor
1μF
B characteristics are recommended
C2
Tank capacitor
1μF
B characteristics are recommended
C3
Input coupling capacitor
1μF
B characteristics are recommended
C4
Decoupling capacitor
3.3μF
B characteristics are recommended
R1
Output resistor
75Ω
R2
Output terminating resistance
75Ω
R3
Input terminating resistance
75Ω
CN1
Input connector
BNC
CN2
Output connector
RCA (pin jack)
SW
STBY control
SW
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
10/16
－
Not required when connecting to TV
or video signal test equipment.
Required when connecting to video
signal test equipment.
2014.08 - Rev.B
Technical Note
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
●Reference data
BH76812FVM
Ta=25℃
BH76812FVM
25
20
15
10
5
0.8
0.6
0.4
0.2
0
0
1
2
3
0
2.5
4
POWER SUPPLY VOLTAGE [V]
BH76812FVM
VCC=3V
20
1
18
0.8
STANDBY CURRENT [μA]
CIRCUIT CURRENT [mA]
BH76812FVM
16
14
12
10
-50
0
50
0.4
0.2
0
50
TEMPERATURE [℃]
Ta=25℃
BH76812FVM
25
25
VOUT DC OFFSET [mV]
50
0
-25
3.5
-25
0
50
TEMPERATURE [℃]
BH76812FVM
VCC=3V
100
Fig. 21 VOUT DC offset voltage
vs. Temperature
Fig. 20 VOUT DC offset voltage
vs. Supply voltage
BH76812FVM
VCC=3V
0
-50
-50
-50
5
100
Fig. 19 Circuit Current (Standby) vs. Temperature
50
2.7
2.9
3.1
3.3
POWER SUPPLY VOLTAGE [V]
VCC=3V
0.6
-50
Fig. 18 Circuit current vs. Temperature
2.5
3.5
0
100
TEMPERATURE [℃]
BH76812FVM
2.7
2.9
3.1
3.3
POWER SUPPLY VOLTAGE [V]
Fig. 17 Circuit Current (Standby) vs. Supply Voltage
Fig. 16 Circuit current vs. Supply voltage
VOUT DC OFFSET [mV]
Ta=25℃
1
STANDBY CURRENT [μA]
CIRCUIT CURRENT [mA]
30
Ta=25℃
Ta=25℃
12.5
12.4
-5
VOLTAGE GAIN [dB]
VOLTAGE GAIN [dB]
12.3
-15
-25
-35
-45
-55
12.2
12.1
12
11.9
11.8
11.7
-65
11.6
-75
0.1
10
1
FREQUENCY [MHz]
11.5
2.5
100
Fig. 22 Frequency characteristic
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2.7
2.9
3.1
3.3
POWER SUPPLY VOLTAGE [V]
3.5
Fig. 23 Voltage gain vs. Supply voltage
11/16
2014.08 - Rev.B
Technical Note
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
BH76812FVM
BH76812FVM
VCC=3V
12.5
FREQENCY RESPONSE1:Gf1[dB]
12.4
VOLTAGE GAIN [dB]
12.3
12.2
12.1
12
11.9
11.8
11.7
11.6
11.5
-50
0
50
0.8
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
100
2.5
VCC=3V
3.1
3.3
3.5
BH76812FVM
Ta=25℃
0
f=4. 5MHz/100kHz
f=8MHz/100kHz
FREQUENCY RESPONSE2:Gf2[dB]
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
-50
0
50
-1
-2
-3
-4
-5
-6
100
2.5
TEMPERATURE[℃]
FREQUENCY RESPONSE4:Gf4[dB]
f=8MHz/100kHz
-1
-2
-3
-4
-5
3.3
3.5
f=23.5MHz/100kHz
-45
-50
-55
-60
-65
-70
2.5
0
50
TEMPERATURE [℃]
Ta=25℃
-40
-6
2.7
2.9
3.1
3.3
3.5
POWER SUPPLY VOLTAGE:Vcc[V]
100
Fig. 28 Frequency response 2 vs. Temperature
BH76812FVM
3.1
BH76812FVM
0
-50
2.9
Fig. 27 Frequency response 2 vs. Supply voltage
VCC=3V
BH76812FVM
2.7
POWER SUPPLY VOLTAGE: Vcc [V]
Fig. 26 Frequency response 1 vs. Temperature
FREQUENCY RESPONSE2:Gf2[dB]
2.9
Fig. 25 Frequency response 1 vs. Supply voltage
1
FREQUENCY RESPONSE1:Gf1[dB]
2.7
POWER SUPPLY VOLTAGE:Vcc[V]
Fig. 24 Voltage gain vs. Temperature
BH76812FVM
f=4. 5MHz/100kHz
0.6
TEMPERATURE [℃]
Fig.29 Frequency response 4 vs. Supply voltage
BH76812FVM
VCC=3V
7
-40
f=23.5MHz/100kHz
MAX OUTPUT VOLTAGE [VP-P]
FREQUENCY RESPONSE4:Gf4[dB]
Ta=25℃
1
-45
-50
-55
-60
-65
Ta=25℃
6
5
4
3
2
1
0
-70
TEMPERATURE[℃
[Deg]
TEMPERATURE
]
2.7
2.9
3.1
3.3
POWER SUPPLY VOLTAGE [V]
Fig. 30 Frequency response 4 vs. Temperature
Fig. 31 Maximum output voltage level vs. Supply voltage
-50
0
50
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2.5
100
12/16
3.5
2014.08 - Rev.B
Technical Note
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
BH76812FVM
VCC=3V
5.8
5.6
5.4
5.2
5
4.8
4.6
4.4
2
1
6dB
9dB
12dB
16.5dB
0
-1
-2
-3
-1.5
4
0
50
100
TEMPERATURE[V]
Fig. 32 Maximum output level vs. Temperature
260
220
180
140
2.7
2.9
3.1
3.3
3.5
260
220
180
140
100
-50
BH76812FVM
Ta=25℃
0.0
-0.5
-1.0
-1.5
-2.0
-2.5
-3.0
-3.5
-4.0
-1.5
-2
-2.5
-3
0
BH76812FVM
2.5
2.5
DIFFERENTIAL PHASE [Deg]
3
2
1.5
1
0.5
40
VCC=3V
2
1.5
1
0.5
0
-50
3.5
0
50
TEMPERATURE [℃]
100
Fig. 39 Differential phase vs. Temperature
Fig. 38 Differential phase vs. Supply voltage
www.rohm.com
10
20
30
LOAD CURRENT [mA]
Fig. 37 Charge pump load regulation
Ta=25℃
© 2009 ROHM Co., Ltd. All rights reserved.
VCC=3V Ta=25℃
-1
3
2.7
2.9
3.1
3.3
POWER SUPPLY VOLTAGE [V]
100
-0.5
4.0
Fig. 36 Charge pump output voltage
vs. Supply voltage
0
2.5
50
0
CHARGEPUMP OUTPUT VOLTAGE [V]
0.5
BH76812FVM
0
Fig. 35 Charge pump oscillation frequency
vs. Temperature
1.0
1.0
2.0
3.0
POWER SUPPLY VOLTAGE [V]
VCC=3V
TEMPERATURE [℃]
Fig. 34 Charge pump oscillation frequency
vs. Supply voltage
0.0
1.5
300
POWER SUPPLY VOLTAGE [V]
BH76812FVM
-0.5
0.0
0.5
1.0
INPUT DC VOLTAGE [V]
BH76812FVM
Ta=25℃
300
100
2.5
-1.0
Fig. 33 Output DC voltage – Input DC voltage
CHARGEPUMP OSC FREQUENCY [KHz]
CHARGEPUMP OSC FREQUENCY [KHz]
BH76812FVM
CHARGEPUMP OUTPUT VOLTAGE [V]
Ta=25℃
4.2
-50
DIFFERENTIAL PHASE [Deg]
VCC=3V
3
OUTPUT DC VOLTAGE [V]
MAXIMUM OUTPUT LEVEL:Vomv[Vpp]
BH76812FVM
6
13/16
2014.08 - Rev.B
Technical Note
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
Ta=25℃
BH76812FVM
3
2.5
2.5
DIFFERENTIAL GAIN [%]
DIFFERENTIAL GAIN [%]
BH76812FVM
3
2
1.5
1
0.5
0
2.5
2.7
2.9
3.1
3.3
POWER SUPPLY VOLTAGE [V]
Fig. 40 Differential gain vs. Supply voltage
1
0.5
0
50
TEMPERATURE [℃]
100
Fig. 41 Differential gain vs. Temperature
VCC=3V
BH76812FVM
80
80
75
75
Y S/N [dB]
Y S/N [dB]
1.5
Ta=25℃
BH76812FVM
70
65
70
65
60
2.5
2.7
2.9
3.1
3.3
POWER SUPPLY VOLTAGE [V]
60
-50
3.5
50
100
Fig.43 S/N(Y) vs. Temperature
Ta=25℃
BH76812FVM
0
TEMPERATURE [℃]
Fig. 42 S/N(Y) vs. Supply Voltage
VCC=3V
BH76812FVM
80
CHROMA S/N (AM) [dB]
80
75
CHROMA S/N (AM) [dB]
2
0
-50
3.5
VCC=3V
70
65
60
2.5
75
70
65
60
2.7
2.9
3.1
3.3
POWER SUPPLY VOLTAGE [V]
3.5
-50
Fig. 44 S/N(C-AM) vs. Supply Voltage
BH76812FVM
0
50
TEMPERATURE [℃]
100
Fig. 45 S/N(C-AM) vs. Temperature
Ta=25℃
BH76812FVM
70
VCC=3V
70
66
CHROMA S/N (PM) [dB]
C SYSTEM PM S/N:SNcp[dB]
68
64
62
60
58
56
54
65
60
55
52
50
2.5
2.7
2.9
3.1
3.3
50
-50
3.5
POWER SUPPLY VOLTAGE: Vcc[V]
Fig. 46 S/N(C-PM) vs. Supply Voltage
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
0
50
100
TEMPERATURE [℃]
Fig. 47 S/N(C-PM) vs. Temperature
14/16
2014.08 - Rev.B
Technical Note
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
BH76812FVM
VCC=3V Ta=25℃
CIRCUIT CURRENT [mA]
20
15
10
5
0
0.0
0.5
1.0
1.5
STBY TERMINAL VOLTAGE [V]
2.0
Fig. 48 Circuit current vs. STBY terminal voltage
●Cautions on use
1.
Numbers and data in entries are representative design values and are not guaranteed values of the items.
2.
Although ROHM is confident that the example application circuit reflects the best possible recommendations, be sure
to verify circuit characteristics for your particular application. Modification of constants for other externally connected
circuits may cause variations in both static and transient characteristics for external components as well as this Rohm
IC. Allow for sufficient margins when determining circuit constants.
3.
Absolute maximum ratings
Use of the IC in excess of absolute maximum ratings, such as the applied voltage or operating temperature range
(Topr), may result in IC damage. Assumptions should not be made regarding the state of the IC (short mode or
open mode) when such damage is suffered. A physical safety measure, such as a fuse, should be implemented
when using the IC at times where the absolute maximum ratings may be exceeded.
4.
Thermal design
Perform thermal design, in which there are adequate margins, by taking into account the permissible dissipation
(Pd) in actual states of use.
5.
Short circuit between terminals and erroneous mounting
Pay attention to the assembly direction of the ICs. Wrong mounting direction or shorts between terminals, GND, or other
components on the circuits, can damage the IC.
6.
Operation in strong electromagnetic field
Using the ICs in a strong electromagnetic field can cause operation malfunction.
7.
Wiring from the decoupling capacitor C2 to the IC should be kept as short as possible.
This capacitance value may have ripple effects on the IC, and may affect the S-N ratio. It is recommended to use
as large a decoupling capacitor as possible. (Recommendations: 3.3 µF, B characteristics, 6.3 V or higher)
8.
Target capacitor
It is recommended to use a ceramic capacitor with good temperature characteristics (B).
9.
The NVCC (7 pin) terminal generates a voltage that is used within the IC, so it should not be connected to a load
unless necessary. This capacitor (C7) has a large capacitance value with low negative voltage ripple.
10.
Capacitors C18 and C2 should be placed as close as possible to the IC.
If the wire length to the capacitor is too
long, it can lead to switching noise. (Recommended C18: 1.0 µF; C2: 3.3 µF, B characteristics, 6.3 V or higher
maximum voltage)
11.
The HPF consists of input coupling capacitor C3 and 150 kΩ of the internal input.
Be sure to check for video signal sag before determining the C3 value.
The cut-off frequency fc can be calculated using the following formula.
fc = 1/(2π× C3 × 150 kΩ) (Recommendations:
1.0 µF, B characteristics, 6.3 V or higher maximum voltage)
12.
The output resistor R5 should be placed close to the IC.
13.
Improper mounting may damage the IC.
14.
A large current transition occurs in the power supply pin when the charge pump circuit is switched.
If this affects
other ICs (via the power supply line), insert a resistor (approximately 10 Ω) in the VCC line to improve the power
supply's ripple effects. Although inserting a 10 Ω resistor lowers the voltage by about 0.2 V, this IC has a wide margin
for low-voltage operation, so dynamic range problems or other problems should not occur. (See Figures 12 to 14.)
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
15/16
2014.08 - Rev.B
Technical Note
BH76806FVM, BH76809FVM, BH76812FVM, BH76816FVM
●Selection of order type
B
H
7
6
8
6
0
F
V
T
M
R
Tape and Reel
information
Part. No.
BH76806FVM
BH76809FVM
BH76812FVM
BH76816FVM
MSOP8
<Dimension>
<Tape and Reel information>
Tape
Embossed carrier tape
Quantity
3000pcs
Direction
of feed
TR
The direction is the 1pin of product is at the upper right when you hold
( reel on the left hand and you pull out the tape on the right hand
)
1pin
Direction of feed
Reel
(Unit:mm)
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
16/16
∗ Order quantity needs to be multiple of the minimum quantity.
2014.08 - Rev.B
Notice
Notes
1) The information contained herein is subject to change without notice.
2) Before you use our Products, please contact our sales representative and verify the latest specifications :
3) Although ROHM is continuously working to improve product reliability and quality, semiconductors can break down and malfunction due to various factors.
Therefore, in order to prevent personal injury or fire arising from failure, please take safety
measures such as complying with the derating characteristics, implementing redundant and
fire prevention designs, and utilizing backups and fail-safe procedures. ROHM shall have no
responsibility for any damages arising out of the use of our Poducts beyond the rating specified by
ROHM.
4) Examples of application circuits, circuit constants and any other information contained herein are
provided only to illustrate the standard usage and operations of the Products. The peripheral
conditions must be taken into account when designing circuits for mass production.
5) The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly,
any license to use or exercise intellectual property or other rights held by ROHM or any other
parties. ROHM shall have no responsibility whatsoever for any dispute arising out of the use of
such technical information.
6) The Products are intended for use in general electronic equipment (i.e. AV/OA devices, communication, consumer systems, gaming/entertainment sets) as well as the applications indicated in
this document.
7) The Products specified in this document are not designed to be radiation tolerant.
8) For use of our Products in applications requiring a high degree of reliability (as exemplified
below), please contact and consult with a ROHM representative : transportation equipment (i.e.
cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety
equipment, medical systems, servers, solar cells, and power transmission systems.
9) Do not use our Products in applications requiring extremely high reliability, such as aerospace
equipment, nuclear power control systems, and submarine repeaters.
10) ROHM shall have no responsibility for any damages or injury arising from non-compliance with
the recommended usage conditions and specifications contained herein.
11) ROHM has used reasonable care to ensur the accuracy of the information contained in this
document. However, ROHM does not warrants that such information is error-free, and ROHM
shall have no responsibility for any damages arising from any inaccuracy or misprint of such
information.
12) Please use the Products in accordance with any applicable environmental laws and regulations,
such as the RoHS Directive. For more details, including RoHS compatibility, please contact a
ROHM sales office. ROHM shall have no responsibility for any damages or losses resulting
non-compliance with any applicable laws or regulations.
13) When providing our Products and technologies contained in this document to other countries,
you must abide by the procedures and provisions stipulated in all applicable export laws and
regulations, including without limitation the US Export Administration Regulations and the Foreign
Exchange and Foreign Trade Act.
14) This document, in part or in whole, may not be reprinted or reproduced without prior consent of
ROHM.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2014 ROHM Co., Ltd. All rights reserved.
R1102A