SLOS070B − JULY 1979 − REVISED FEBRUARY 2004
D Equivalent Input Noise Voltage . . .
D
D
D
D
D
D
D
D
D
NE5534 . . . D, P, OR PS PACKAGE
NE5534A . . . D OR P PACKAGE
(TOP VIEW)
3.5 nV//Hz
Unity-Gain Bandwidth . . . 10 MHz Typ
Common-Mode Rejection Ratio . . .
100 dB Typ
High DC Voltage Gain . . . 100 V/mV Typ
Peak-to-Peak Output Voltage Swing
32 V Typ With VCC+ = +18 V and RL = 600 W
High Slew Rate . . . 13 V/ms Typ
Wide Supply-Voltage Range +3 V to +20 V
Low Harmonic Distortion
Offset Nulling Capability
External Compensation Capability
BALANCE
IN−
IN+
VCC−
1
8
2
7
3
6
4
5
COMP/BAL
VCC+
OUT
COMP
description/ordering information
The NE5534 and NE5534A are high-performance operational amplifiers combining excellent dc and ac
characteristics. Some of the features include very low noise, high output-drive capability, high unity-gain and
maximum-output-swing bandwidths, low distortion, and high slew rate.
These operational amplifiers are compensated internally for a gain equal to or greater than three. Optimization
of the frequency response for various applications can be obtained by use of an external compensation
capacitor between COMP and COMP/BAL. The devices feature input-protection diodes, output short-circuit
protection, and offset-voltage nulling capability with use of the BALANCE and COMP/BAL pins (see the
application circuit diagram).
For the NE5534A, a maximum limit is specified for the equivalent input noise voltage.
ORDERING INFORMATION
TA
VIOmax
AT 25°C
PDIP (P)
0°C
70°C
0
C to 70
C
ORDERABLE
PART NUMBER
PACKAGE†
4 mV
SOIC (D)
TOP-SIDE
MARKING
Tube of 50
NE5534P
NE5534P
Tube of 50
NE5534AP
NE5534AP
Tube of 75
NE5534D
Reel of 2500
NE5534DR
Tube of 75
NE5534AD
Reel of 2500
NE5534ADR
NE5534
5534A
SOP (PS)
Reel of 2000
NE5534PS
N5534
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available
at www.ti.com/sc/package.
Copyright 2004, Texas Instruments Incorporated
!" #!$% &"'
&! #" #" (" " ") !"
&& *+' &! #", &" ""%+ %!&"
", %% #""'
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SLOS070B − JULY 1979 − REVISED FEBRUARY 2004
schematic
BALANCE
COMP/BAL
8
1
100 pF
IN+
12 kΩ
COMP
5
7
12 kΩ
3
40 pF
15 Ω
6
IN−
VCC+
2
15 Ω
7 pF
12 pF
OUT
4
VCC−
All component values shown are nominal.
symbol
application circuit
VCC+
22 kΩ
COMP
100 kΩ
COMP/BAL
IN−
CC
1
−
2
OUT
IN+
8
−
5
+
5534
BALANCE
+
3
7
6
4
VCC−
Frequency Compensation and Offset-Voltage Nulling Circuit
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLOS070B − JULY 1979 − REVISED FEBRUARY 2004
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage: VCC+ (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 V
VCC− (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −22 V
Input voltage either input (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC+
Input current (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 mA
Duration of output short circuit (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unlimited
Package thermal impedance, θJA (see Notes 5 and 6): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97°C/W
P package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85°C/W
PS package . . . . . . . . . . . . . . . . . . . . . . . . . . . 95°C/W
Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC−.
2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage.
3. Excessive current will flow if a differential input voltage in excess of approximately 0.6 V is applied between the inputs, unless some
limiting resistance is used.
4. The output may be shorted to ground or to either power supply. Temperature and/or supply voltages must be limited to ensure the
maximum dissipation rating is not exceeded.
5. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable
ambient temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
6. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions
VCC+
VCC−
MIN
MAX
Supply voltage
5
15
V
Supply voltage
−5
−15
V
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
3
SLOS070B − JULY 1979 − REVISED FEBRUARY 2004
electrical characteristics, VCC± = ±15 V, TA = 25°C (unless otherwise noted)
TEST CONDITIONS†
PARAMETER
MIN
TYP
MAX
4
Input offset voltage
VO = 0,
RS = 50 Ω
TA = 25°C
TA = Full range
0.5
VIO
Input offset current
VO = 0
TA = 25°C
TA = Full range
20
IIO
Input bias current
VO = 0
TA = 25°C
TA = Full range
500
IIB
VICR
Common-mode input voltage range
±12
±13
24
26
30
32
25
100
VO(PP)
Maximum peak-to-peak output voltage swing
RL ≥ 600 Ω
VCC± = ±15 V
VCC± = ±18 V
AVD
Large-signal differential voltage amplification
VO = ±10 V,
RL ≥ 600 Ω
TA = 25°C
TA = Full range
Avd
Small-signal differential voltage amplification
f = 10 kHz
B1
ri
Maximum-output-swing bandwidth
Unity-gain bandwidth
mV
300
400
nA
1500
2000
nA
V
V
V/mV
15
CC = 0
VO = ±10 V
BOM
5
UNIT
6
CC = 22 pF
2.2
CC = 0
200
V/mV
CC = 22 pF
95
VCC± = ±18 V,
RL ≥ 600 Ω,
VO = ±14 V,
CC = 22 pF
70
CC = 22 pF,
CL = 100 pF
10
MHz
100
kΩ
RL ≥ 600 Ω,
f = 10 kHz
0.3
Ω
Input resistance
30
kHz
zo
Output impedance
AVD = 30 dB,
CC = 22 pF,
CMRR
Common-mode rejection ratio
VO = 0,
RS = 50 Ω
VIC = VICRmin,
70
100
dB
kSVR
Supply-voltage rejection ratio (∆VCC/∆VIO)
VCC+ = ±9 V to ±15 V,
VO = 0
RS = 50 Ω,
80
100
dB
IOS
Output short-circuit current
38
mA
ICC
Supply current
VO = 0, No load
TA = 25°C
4
8
mA
† All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified. Full range is
TA = 0°C to 70°C.
operating characteristics, VCC ± = ±15 V, TA = 25°C
NE5534
PARAMETER
SR
Slew rate
Rise time
Overshoot factor
tr
Rise time
Overshoot factor
Vn
Equivalent input noise voltage
In
Equivalent input noise current
F
Average noise figure
4
TEST CONDITIONS
CC = 0
CC = 22 pF
TYP
NE5534A
MIN
TYP
13
13
6
6
MAX
UNIT
V/ s
V/µs
VI = 50 mV,
RL = 600 Ω,
CL = 100 pF
AVD = 1,
CC = 22 pF
20
20
ns
20
20
%
VI = 50 mV,
RL = 600 Ω,
CL = 500 pF
AVD = 1,
CC = 47 pF
50
50
ns
35
35
%
f = 30 Hz
7
5.5
7
f = 1 kHz
4
3.5
4.5
f = 30 Hz
2.5
1.5
f = 1 kHz
0.6
0.4
RS = 5 kΩ,
POST OFFICE BOX 655303
f = 10 Hz to 20 kHz
• DALLAS, TEXAS 75265
0.9
nV/√Hz
pA/√Hz
dB
SLOS070B − JULY 1979 − REVISED FEBRUARY 2004
NORMALIZED INPUT BIAS CURRENT
AND INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
VO(PP)
VOPP − Maximum Peak-to-Peak Output Voltage − V
Normalized Input Bias Current and Input Offset Current
TYPICAL CHARACTERISTICS†
1.6
VCC± = ±15 V
1.4
Offset
1.2
Bias
1
0.8
0.6
0.4
−75 −50
75
100
−25
0
25
50
TA − Free-Air Temperature − °C
125
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE
vs
FREQUENCY
30
CC = 0
25
20
15
10
ÁÁÁ
ÁÁÁ
ÁÁÁ
CC = 22 pF
5
VCC± = ±15 V
TA = 25°C
0
100
1k
NORMALIZED SLEW RATE AND
UNITY-GAIN BANDWIDTH
vs
SUPPLY VOLTAGE
103
CC = 0 pF
102
CC = 22 pF
1k
10 k 100 k 1 M
f − Frequency − Hz
10 M 100 M
Normalized Slew Rate and Unity-Gain Bandwidth
AVD − Differential Voltage Amplification − V/mV
104
100
1M
1.2
VCC± = ±15 V
TA = 25°C
105
1
10
100 k
Figure 2
LARGE-SIGNAL
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
FREQUENCY
10
10 k
f − Frequency − Hz
Figure 1
106
CC = 47 pF
TA = 25°C
1.1
Unity-Gain
Bandwidth
1
0.9
0.8
0.7
Slew Rate
0.6
0.5
0.4
0
Figure 3
15
5
10
| VCC± | − Supply Voltage − V
20
Figure 4
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SLOS070B − JULY 1979 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS†
NORMALIZED SLEW RATE AND
UNITY-GAIN BANDWIDTH
vs
FREE-AIR TEMPERATURE
TOTAL HARMONIC DISTORTION
vs
FREQUENCY
0.01
VCC± = ±15 V
1.1
THD − Total Harmonic Distortion − %
Normalized Slew Rate and Unity-Gain Bandwidth
1.2
Slew Rate
Unity-Gain
Bandwidth
1
0.9
0.8
−75
−50
75 100
−25
0
25
50
TA − Free-Air Temperature − °C
0.007
VCC± = ±15 V
AVD = 1
VI(rms) = 2 V
TA = 25°C
0.004
0.002
0.001
100
125
400
I n − Equivalent Input Noise Current − pA/ Hz
Vn − Equivalent Input Noise Voltage − nV/ Hz
10
VCC± = ±15 V
TA = 25°C
SE5534, NE5534
SE5534A, NE5534A
2
100
40 k 100 k
EQUIVALENT INPUT NOISE CURRENT
vs
FREQUENCY
4
1
10
10 k
Figure 6
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
7
4k
f − Frequency − Hz
Figure 5
10
1k
1k
10 k
100 k
VCC± = ±15 V
TA = 25°C
7
4
2
1
SE5534, NE5534
0.7
0.4
SE5534A, NE5534A
0.2
0.1
10
f − Frequency − Hz
100
1k
10 k
100 k
f − Frequency − Hz
Figure 8
Figure 7
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLOS070B − JULY 1979 − REVISED FEBRUARY 2004
TYPICAL CHARACTERISTICS
TOTAL EQUIVALENT INPUT NOISE VOLTAGE
vs
SOURCE RESISTANCE
Total Equivalent Input Noise Voltage − µV
100
70
40
VCC± = ±15 V
TA = 25°C
20
10
7
4
f = 10 Hz to 20 kHz
2
1
0.7
0.4
f = 200 Hz to 4 kHz
0.2
0.1
100
1k
10 k
100 k
RS − Source Resistance − Ω
1M
Figure 9
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUARY 1997
JG (R-GDIP-T8)
CERAMIC DUAL-IN-LINE
0.400 (10,16)
0.355 (9,00)
8
5
0.280 (7,11)
0.245 (6,22)
1
0.063 (1,60)
0.015 (0,38)
4
0.065 (1,65)
0.045 (1,14)
0.310 (7,87)
0.290 (7,37)
0.020 (0,51) MIN
0.200 (5,08) MAX
Seating Plane
0.130 (3,30) MIN
0.023 (0,58)
0.015 (0,38)
0°–15°
0.100 (2,54)
0.014 (0,36)
0.008 (0,20)
4040107/C 08/96
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a ceramic lid using glass frit.
Index point is provided on cap for terminal identification.
Falls within MIL STD 1835 GDIP1-T8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.325 (8,26)
0.300 (7,62)
0.020 (0,51) MIN
0.015 (0,38)
Gage Plane
0.200 (5,08) MAX
Seating Plane
0.010 (0,25) NOM
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.015 (0,38)
0.430 (10,92)
MAX
0.010 (0,25) M
4040082/D 05/98
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2004, Texas Instruments Incorporated