STMicroelectronics L6926Q1TR High efficiency monolithic synchronous step down regulator Datasheet

L6926
High efficiency monolithic synchronous step down regulator
Features
■
2 V to 5.5 V battery input range
■
High efficiency: up to 95 %
■
Internal synchronous switch
■
No external schottky required
■
Extremely low quiescent current
■
1 mA max shutdown supply current
■
800 mA max output current
■
Adjustable output voltage from 0.6 V
■
Low drop-out operation: up to 100 % duty cycle
■
Selectable low noise/low consumption mode at
light load
VFQFPN8
(3x3x1.0 mm)
MSOP8
Description
The device is DC-DC monolithic regulator
specifically designed to provide extremely high
efficiency.
L6926 supply voltage can be as low as 2 V
allowing its use in single Li-ion cell supplied
applications. Output voltage can be selected by
an external divider down to 0.6 V.
■
Power good signal
■
±1 % output voltage accuracy
■
Current-mode control
■
600 kHz switching frequency
Duty cycle can saturate to 100 % allowing low
drop-out operation.
■
Externally synchronizable
from 500 kHz to 1.4 MHz
The device is based on a 600 kHz fixedfrequency, current mode-architecture.
■
OVP
■
Short circuit protection
Low consumption mode operation can be
selected at light load conditions, allowing
switching losses to be reduced. L6926 is
externally synchronizable with a clock which
makes it useful in noise-sensitive applications.
Other features like powergood, overvoltage
protection, shortcircuit protection and thermal
shutdown (150 °C) are also present.
Applications
■
Battery-powered equipments
■
Portable instruments
■
Cellular phones
■
PDAs and hand held terminals
■
DSC
■
GPS
Figure 1.
Application test circuit
L 6.8μH
VIN=2V to 5.5V
C1
10μF
6.3V
SYNC
VCC
RUN
5
7
6
September 2008
R2
200K
C4
10μF
6.3V
PGOOD
2
D01IN1305
R3
500K
VOUT=1.8V
8
1
COMP
LX
4
C2
220pF
3
VFB
GND
Rev 8
R1
100K
1/16
www.st.com
16
Contents
L6926
Contents
1
2
Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1
Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2
Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4
Operation description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.1
5
Modes of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1.1
Low consumption mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1.2
Low noise mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1.3
Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2
Short circuit protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.3
Slope compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.4
Loop stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Additional features and protections . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.1
DROPOUT operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.2
PGOOD (power good output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.3
Adjustable output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.4
OVP (overvoltage protection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.5
Thermal shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7
Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2/16
L6926
Pin settings
1
Pin settings
1.1
Pin connection
Figure 1.
Pin connection (top view)
RUN
1
8
PGOOD
COMP
2
7
SYNC
VFB
3
6
VCC
GND
4
5
LX
D01IN1239AMOD
1.2
Pin description
Table 1.
Pin description
Pin N°
Name
1
RUN
2
COMP
Error amplifier output. A compensation network has to be connected to this pin.
Usually a 220 pF capacitor is enough to guarantee the loop stability.
3
VFB
Error amplifier inverting input. The output voltage can be adjusted from 0.6 V up
to the input voltage by connecting this pin to an external resistor divider.
4
GND
Ground.
5
LX
Switch output node. This pin is internally connected to the drain of the internal
switches.
6
VCC
Input voltage. The start up input voltage is 2.2 V (typ) while the operating input
voltage range is from 2 V to 5.5 V. An internal UVLO circuit realizes a 100 mV
(typ.) hysteresis.
7
8
SYNC
Description
Shutdown input. When connected to a low level (lower than 0.4 V) the device
stops working. When high (higher than 1.3 V) the device is enabled.
Operating mode selector input. When high (higher than 1.3 V) the Low
Consumption Mode is selected. When low (lower than 0.5 V) the low noise
mode is selected. If connected with an appropriate external synchronization
signal (from 500 kHz up to 1.4 MHz) the internal synchronization circuit is
activated and the device works at the same switching frequency.
Power good comparator output. It is an open drain output. A pull-up resistor
should be connected between PGOOD and VOUT (or VCC depending on the
PGOOD requirements). The pin is forced low when the output voltage is lower than 90%
of the regulated output voltage and goes high when the output voltage is greater
than 90% of the regulated output voltage. If not used the pin can be left floating.
3/16
Maximum ratings
L6926
2
Maximum ratings
2.1
Absolute maximum ratings
Table 2.
Absolute maximum ratings
Symbol
Unit
Input voltage
-0.3 to 6
V
V5
Output switching voltage
-1 to VCC
V
V1
Shutdown
-0.3 to VCC
V
V3
Feedback voltage
-0.3 to VCC
V
V2
Error amplifier output voltage
-0.3 to VCC
V
V8
PGOOD
-0.3 to VCC
V
V7
Synchronization mode selector
-0.3 to VCC
V
Ptot
Power dissipation at TA = 70 °C
0.45
W
TJ
Junction operating temperature range
-40 to 150
°C
Storage temperature range
-65 to 150
°C
±1000
V
±2000
V
LX pin
Other pins
Maximum withstanding voltage range test condition:
CDF-AEC-Q100-002- “Human body model”
acceptance criteria: “normal performance’
Thermal data
Table 3.
Symbol
RthJA
4/16
Value
V6
Tstg
2.2
Parameter
Thermal data
Parameter
Value
Unit
Maximum thermal resistance junction-ambient for MSOP8
180
°C/W
Maximum thermal resistance junction-ambient for VFQFPN8
56
°C/W
L6926
Electrical characteristics
3
Electrical characteristics
Table 4.
Electrical characteristcs
(TJ = 25 °C, VIN = 3.6 V unless otherwise specified) (1)
Symbol
Vcc
Parameter
Test condition
Operating input voltage
Vcc ON
Turn on threshold
Vcc OFF
Turn off threshold
Vcc hys
Hysteresis
After turn on
Min
(1)
Typ
2
High side Ron
Rn
Low side Ron
Unit
5.5
V
2.2
V
2
100
240
Rp
Max
Vcc = 3.6 V, Ilx =100 mA
Vcc = 3.6 V
(1)
Ilim
mΩ
Vcc = 3.6 V
Vout
Output voltage range
fosc
Oscillator frequency
fsync
Sync mode clock (2)
(1)
(1)
1.2
1.5
A
0.85
1
Valley current limit
300
400
1
Peak current limit
300
400
215
(1)
mV
mΩ
(1)
Vcc = 3.6 V, Ilx =100 mA
V
1.65
1.4
1.7
A
0.9
1.85
Vfb
Vcc
450
600
700
400
600
800
V
kHz
500
1400
kHz
DC characteristics
Vsync = 0 V, no load,
VFB > 0.6 V
Quiescent current
(low noise mode)
Vsync = 0 V, no load,
VFB > 0.6 V
Iq
Ish
Ilx
200
300
μA
(1)
300
Quiescent current
(low cunsumption mode)
Vsync = Vcc, no load,
VFB > 0.6 V
Shutdown current
RUN to GND, Vcc = 5.5 V
0.2
μA
RUN to GND, VLX = 5.5 V,
Vcc = 5.5 V
1
μA
RUN to GND, VLX = 0V,
Vcc = 5.5 V
1
μA
LX leakage current
(2)
(1)
25
50
μA
5/16
Electrical characteristics
Table 4.
L6926
Electrical characteristcs (continued)
(TJ = 25 °C, VIN = 3.6 V unless otherwise specified) (1)
Symbol
Parameter
Test condition
Min
Typ
Max
Unit
0.593
0.600
0.607
V
0.590
0.600
0.610
V
Error amplifier characteristics
Vfb
Ifb
Voltage feedback
(1)
Feedback input current
(2)
VFB = 0.6 V
25
nA
Run
Vrun_H
RUN threshold high
Vrun_L
RUN threshold low
Irun
RUN input current
1.3
0.4
(2)
V
V
25
nA
SYNC/MODE function
Vsync_H
Sync mode threshold high
Vsync_L
Sync mode threshold low
1.3
0.5
V
V
PGOOD section
VPGOOD
Power good threshold
VOUT = Vfb
90
%Vout
ΔVPGOOD
Power good hysteresis
VOUT = Vfb
4
%Vout
VPgood(low) Power good low voltage
Run to GND
Power good leakage current
ILK-PGOOD (2)
VPGOOD = 3.6 V
0.4
V
50
nA
10
%Vout
Protections
HOVP
Hard overvoltage threshold
VOUT = Vfb
1. Specification referred to TJ from -40 °C to +125 °C. Specification over the -40 to +125 °C TJ temperature range are assured
by design, characterization and statistical correlation.
2. Guaranteed by design
6/16
L6926
4
Operation description
Operation description
The main loop uses slope compensated PWM current mode architecture. Each cycle the
high side MOSFET is turned on, triggered by the oscillator, so that the current flowing
through it (the same as the inductor current) increases. When this current reaches the
threshold (set by the output of the error amplifier E/A), the peak current limit comparator
PEAK_CL turns off the high side MOSFET and turns on the low side one until the next clock
cycle begins or the current flowing through it goes down to zero (ZERO CROSSING
comparator). The peak inductor current required to trigger PEAK_CL depends on the slope
compensation signal and on the output of the error amplifier.
In particular, the error amplifier output depends on the VFB pin voltage. When the output
current increases, the output capacitor is discharged and so the VFB pin decreases. This
produces increase of the error amplifier output, so allowing a higher value for the peak
inductor current. For the same reason, when due to a load transient the output current
decreases, the error amplifier output goes low, so reducing the peak inductor current to
meet the new load requirements.
The slope compensation signal allows the loop stability also in high duty cycle conditions
(see related section)
Figure 2.
Device block diagram
RUN
SYNC
VCC
OSCILLATOR
COM P
FB
GND
LOW
NOISE/
CONSUM PTION
SLOPE
LOOP
CONTROL
E/A
VREF
POWER
PMOS
SENSE
PMOS
GND
PEAK
CL
LX
DRIVER
0.6V
OVP
PGOOD
VREF
0.9V
ZERO
CROSSING
Vcc
SENSE
NMOS
Vcc
POWER
NMOS
GND
PGOOD
VALLEY
CL
GND
7/16
Operation description
4.1
L6926
Modes of operation
Depending on the SYNC pin value the device can operate in low consumption or low noise
mode. If the SYNC pin is high (higher than 1.3 V) the low consumption mode is selected
while the low noise mode is selected if the SYNC pin is low (lower than 0.5 V).
4.1.1
Low consumption mode
In this mode of operation, at light load, the device operates discontinuously based on the
COMP pin voltage, in order to keep the efficiency very high also in these conditions. While
the device is not switching the load discharges the output capacitor and the output voltage
goes down. When the feedback voltage goes lower than the internal reference, the COMP
pin voltage increases and when an internal threshold is reached, the device starts to switch.
In these conditions the peak current limit is set approximately in the range of
200 mA-400 mA, depending on the slope compensation (see related section).
Once the device starts to switch the output capacitor is recharged. The feedback pin
increases and, when it reaches a value slightly higher than the reference voltage, the output
of the error amplifier goes down until a clamp is activated. At this point, the device stops to
switch. In this phase, most of the internal circuitries are off, so reducing the device
consumption down to a typical value of 25 μA.
4.1.2
Low noise mode
If for noise reasons, the very low frequencies of the low consumption mode are undesirable,
the low noise mode can be selected. In low noise mode, the efficiency is a little bit lower
compared with the low consumption mode in very light load conditions but for medium-high
load currents the efficiency values are very similar.
Basically, the device switches with its internal free running frequency of 600 kHz. Obviously,
in very light load conditions, the device could skip some cycles in order to keep the output
voltage in regulation.
4.1.3
Synchronization
The device can also be synchronized with an external signal from 500 kHz up to 1.4 MHz.
In this case the low noise mode is automatically selected. The device will eventually skip
some cycles in very light load conditions.
The internal synchronization circuit is inhibited in shortcircuit and overvoltage conditions in
order to keep the protections effective (see relative sections).
8/16
L6926
4.2
Operation description
Short circuit protection
During the device operation, the inductor current increases during the high side turn ON
phase and decrease during the high side turn off phase based on the following equations:
Equation 1
( V IN – V OUT )
ΔI ON = ---------------------------------- ⋅ T ON
L
Equation 2
( V OUT )
ΔI OFF = ------------------- ⋅ T OFF
L
In strong overcurrent or shortcircuit conditions the VOUT can be very close to zero. In this
case ΔION increases and ΔIOFF decreases. When the inductor peak current reaches the
current limit, the high side mosfet turns off and so the TON is reduced down to the minimum
value (250 ns typ.) in order to reduce as much as possible ΔION.
Anyway, if VOUT is low enough it can be that the inductor peak current further increases
because during the TOFF the current decays very slowly.
Due to this reason a second protection that fixes the maximum inductor valley current has
been introduced. This protection doesn't allow the high side MOSFET to turn on if the
current flowing through the inductor is higher that a specified threshold (valley current limit).
Basically the TOFF is increased as much as required to bring the inductor current down to
this threshold.
So, the maximum peak current in worst case conditions will be:
Equation 3
V IN
I PEAK = I VALLEY + --------- ⋅ T ON_MIN
L
Where IPEAK is the valley current limit (1.4 A typ.) and TON_MIN is the minimum TON of the
high side MOSFET.
9/16
Operation description
4.3
L6926
Slope compensation
In current mode architectures, when the duty cycle of the application is higher than
approximately 50%, a pulse-by-pulse instability (the so called sub harmonic oscillation) can
occur.
To allow loop stability also in these conditions a slope compensation is present. This is
realized by reducing the current flowing through the inductor necessary to trigger the COMP
comparator (with a fixed value for the COMP pin voltage).
With a given duty cycle higher than 50%, the stability problem is particularly present with an
higher input voltage (due to the increased current ripple across the inductor), so the slope
compensation effect increases as the input voltage increases.
From an application point of view, the final effect is that the peak current limit depends both
on the duty cycle (if higher than approximately 40%) and on the input voltage.
4.4
Loop stability
Since the device is realized with a current mode architecture, the loop stability is usually not
a big issue. For most of the application a 220 pF connected between the COMP pin and
ground is enough to guarantee the stability. In case very low ESR capacitors are used for
the output filter, such as multilayer ceramic capacitors, the zero introduced by the capacitor
itself can shift at very high frequency and the transient loop response could be affected.
Adding a series resistor to the 220 pF capacitor can solve this problem.
The right value for the resistor (in the range of 50 K) can be determined by checking the load
transient response of the device. Basically, the output voltage has to be checked at the
scope after the load steps required by the application. In case of stability problems, the
output voltage could oscillates before to reach the regulated value after a load step.
10/16
L6926
Additional features and protections
5
Additional features and protections
5.1
DROPOUT operation
The Li-Ion battery voltage ranges from approximately 3 V and 4.1 V-4.2 V (depending on the
anode material). In case the regulated output voltage is from 2.5 V and 3.3 V, it can be that,
close to the end of the battery life, the battery voltage goes down to the regulated one. In
this case the device stops to switch, working at 100% of duty cycle, so minimizing the
dropout voltage and the device losses.
5.2
PGOOD (power good output)
A power good output signal is available. The VFB pin is internally connected to a comparator
with a threshold set at 90% of the of reference voltage (0.6 V). Since the output voltage is
connected to the VFB pin by a resistor divider, when the output voltage goes lower than the
regulated value, the VFB pin voltage goes lower than 90% of the internal reference value.
The internal comparator is triggered and the PGOOD pin is pulled down.
The pin is an open drain output and so, a pull up resistor should be connected to him.
If the feature is not required, the pin can be left floating.
5.3
Adjustable output voltage
The output voltage can be adjusted by an external resistor divider from a minimum value of
0.6V up to the input voltage. The output voltage value is given by:
Equation 4
R
V OUT = 0.6 ⋅ ⎛ 1 + ------2-⎞
⎝
R ⎠
1
5.4
OVP (overvoltage protection)
The device has an internal overvoltage protection circuit to protect the load.
If the voltage at the feedback pin goes higher than an internal threshold set 10% (typ) higher
than the reference voltage, the low side power mosfet is turned on until the feedback voltage
goes lower than the reference one.
During the overvoltage circuit intervention, the zero crossing comparator is disabled so that
the device is also able to sink current.
5.5
Thermal shutdown
The device has also a thermal shutdown protection activated when the junction temperature
reaches 150 °C. In this case both the high side MOSFET and the low side one are turned
off. Once the junction temperature goes back lower than 95 °C, the device restarts the
normal operation.
11/16
Package mechanical data
6
L6926
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a lead-free second level interconnect . The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com
Figure 3.
MSOP8 mechanical data and package dimensions
mm
inch
DIM.
MIN.
TYP.
A
MAX.
MIN.
TYP.
1.10
A1
0.050
A2
0.750
b
0.250
0.850
MAX.
0.043
0.150
0.002
0.950
0.03
0.400
0.010
0.006
0.033
0.037
0.016
c
0.130
0.230
0.005
D (1)
2.900
3.000
3.100
0.114
0.118
0.122
E
4.650
4.900
5.150
0.183
0.193
0.20
E1 (1) 2.900
3.000
3.100
0.114
0.118
0.122
0.700
0.016
0.022
e
L
L1
k
aaa
0.650
0.400
0.550
0.009
0.026
0.950
0.028
0.037
0˚ (min.) 6˚ (max.)
0.100
0.004
Note: 1. D and F does not include mold flash or protrusions.
Mold flash or potrusions shall not exceed 0.15mm
(.006inch) per side.
12/16
OUTLINE AND
MECHANICAL DATA
MSOP8
(Body 3mm)
L6926
Package mechanical data
Figure 4.
VFQFPN8 mechanical data and package dimensions
mm
inch
DIM.
MIN.
TYP.
MAX.
0.80
0.90
1.00
0.0315 0.0354 0.0394
A1
0.02
0.05
0.0008 0.0020
A2
0.70
0.0276
A3
0.20
0.0079
A
b
0.18
D
D2
2.23
2.38
1.49
1.64
2.48
0.40
MAX.
OUTLINE AND
MECHANICAL DATA
0.0071 0.0091 0.0118
0.0878 0.0937 0.0976
0.1181
1.74
0.50
0.30
TYP.
0.1181
3.00
e
L
0.30
3.00
E
E2
0.23
MIN.
0.0587 0.0646 0.0685
0.0197
0.50
0.0118 0.0157 0.0197
VFQFPN8 (3x3x1.0 8mm)
Very thin Fine pitch Quad Packages No lead
ddd
0.08
0.0031
7426334 B
13/16
Order codes
7
Order codes
Table 5.
14/16
L6926
Order codes
Order codes
Package
Packaging
L6926
MSOP8
Tube
L6926013TR
MSOP8
Tape and reel
L6926Q1
VFQFPN8
Tube
L6926Q1TR
VFQFPN8
Tape and reel
L6926
8
Revision history
Revision history
Table 6.
Document revision history
Date
Revision
Changes
Jan-2004
2
First Issue in EDOCS dms.
Sep-2004
3
Changed the style look and feel.
Add. new package VFSON8.
Add. V8 and V7 parameter in the Table 2 - Absolute Maximum Ratings.
Nov-2004
4
Update order codes
Sep-2005
5
Updated “Table. 5 Electrical Characteristics”.
Nov-2005
6
Added VFQFPN8 package and new part numbers.
27-Oct-2006
7
Added RthJA for VFQFPN8 in Table 3. Document has been reformatted.
16-Sep-2008
8
VFSON8 package no longer available
15/16
L6926
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2008 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
16/16