Reflective Photosensors (Photo Reflectors) CNZ2179 (ON2179) Reflective Photosensor Unit : mm 5.2 Overview CNZ2179 is a reflective photosensor with a long focal distance, in which a high efficiency GaAs infrared light emitting diode is used as a light emitting element and a high sensitivity Si phototransistor is used as the light detecting element. Features 0.85max. (2-0.5) Long focal distance : 6 mm (typ.) (2-0.5) Visible light cutoff resin is used (7.6) Symbol Ratings Reverse voltage (DC) Input (Light Forward current (DC) emitting diode) Power dissipation Collector current Unit VR 3 V IF 50 mA PD*1 75 mW IC 20 mA Output (Photo Collector to emitter voltage transistor) Emitter to collector voltage VCEO 20 V VECO 5 V Collector power dissipation PC*2 100 mW Operating ambient temperature Topr –25 to +80 ˚C Storage temperature Tstg –30 to +85 ˚C Temperature *1 *2 (2.54) 1 4 2 3 ; ;; ; Absolute Maximum Ratings (Ta = 25˚C) Parameter 10 min. 8.0 13.0 1 2 3 4 Pin connection (Note) 1. Tolerance unless otherwise specified is ±0.3 2. ( ) Dimension is reference Input power derating ratio is 1.25 mW/˚C at Ta ≥ 25˚C. Output power derating ratio is 1.67 mW/˚C at Ta ≥ 25˚C. Electrical Characteristics (Ta = 25˚C) Parameter Symbol Conditions typ max Unit 1.3 1.5 V VR = 3V 10 µA VCE = 10V 0.2 µA 1500 µA Forward voltage (DC) Input characteristics Reverse current (DC) VF IF = 50mA IR Output characteristics Collector cutoff current ICEO min IC*1 Collector current VCC = 5V, IF = 20mA, RL = 100Ω Transfer Response time tr*2 , tf*3 VCC = 10V, IC = 0.1mA, RL = 100Ω characteristics Collector to emitter saturation voltage VCE(sat) IF = 50mA, IC = 0.1mA *1 Transfer characteristics measurement circuit (Ambient light is shut off completely.) *2 *3 VCC ;; RL 0.5 V Time required for the collector current to increase from 10% to 90% of its final value. Time required for the collector current to decrease from 90% to 10% of its initial value. 90% 10% d = 5 mm Standard white paper (Reflective ratio 90%) µs 20 ;;;; ;;; IC ;; ;; ; ;; ; IF 180 tr tf Note) The part number in the parenthesis shows conventional part number. 1 CNZ2179 Reflective Photosensors (Photo Reflectors) IF , IC — Ta IF — V F VF — Ta 1.6 60 Ta = 25˚C IF 50 30 IC 20 40 30 20 60 80 0 100 0 0.4 0.8 1.2 1.6 1 10 –1 1 IF = 30mA 20mA 10mA 1 RL = 1kΩ 10 500Ω 100Ω 1 20 40 0 60 80 Ambient temperature Ta (˚C ) 100 10 –1 10 –2 10 –1 20 40 60 80 100 Ambient temperature Ta (˚C ) 100 VCC = 10V Ta = 25˚C tr (µs) Rise time 10 –2 0 40 IC — d 10 2 –1 100 80 tr — IC 1 80 120 0 – 40 – 20 10 2 10 10 3 VCE = 10V 60 VCC = 5V IF = 20mA RL = 100Ω Collector to emitter voltage VCE (V) ICEO — Ta 40 IC — Ta 1 10 –1 20 160 10 Forward current IF (mA) 10 –3 – 40 – 20 0 Ambient temperature Ta (˚C ) Ta = 25˚C 10 –2 10 –1 10 2 10 10 0 – 40 – 20 2.4 IC (%) IC (mA) Collector current IC (mA) Collector current 10 10 –2 10 –1 2.0 IC — VCE 10 2 VCE = 5V Ta = 25˚C ICEO (µA) 0.4 Forward voltage VF (V) Relative output current 40 IC — I F Dark current 1mA 1 Collector current IC (mA) 10 IC (%) 20 10 2 2 10mA 0.8 80 Relative output current 0 Ambient temperature Ta (˚C ) 10 1.2 10 10 0 – 25 VF (V) 40 IF = 50mA Forward voltage IF (mA) 50 Forward current Forward current, collector current IF , IC (mA) 60 60 40 20 0 VCC = 5V Ta = 25˚C RL = 100Ω IF = 20mA 0 4 8 12 Distance d (mm) 16 Caution for Safety Gallium arsenide material (GaAs) is used in this product. DANGER Therefore, do not burn, destroy, cut, crush, or chemically decompose the product, since gallium arsenide material in powder or vapor form is harmful to human health. Observe the relevant laws and regulations when disposing of the products. Do not mix them with ordinary industrial waste or household refuse when disposing of GaAs-containing products. Request for your special attention and precautions in using the technical information and semiconductors described in this material (1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuit examples of the products. It does not constitute the warranting of industrial property, the granting of relative rights, or the granting of any license. (3) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: • Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. • Any applications other than the standard applications intended. (4) The products and product specifications described in this material are subject to change without notice for reasons of modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, redundant design is recommended, so that such equipment may not violate relevant laws or regulations because of the function of our products. (6) When using products for which dry packing is required, observe the conditions (including shelf life and afterunpacking standby time) agreed upon when specification sheets are individually exchanged. (7) No part of this material may be reprinted or reproduced by any means without written permission from our company. Please read the following notes before using the datasheets A. These materials are intended as a reference to assist customers with the selection of Panasonic semiconductor products best suited to their applications. Due to modification or other reasons, any information contained in this material, such as available product types, technical data, and so on, is subject to change without notice. Customers are advised to contact our semiconductor sales office and obtain the latest information before starting precise technical research and/or purchasing activities. B. Panasonic is endeavoring to continually improve the quality and reliability of these materials but there is always the possibility that further rectifications will be required in the future. Therefore, Panasonic will not assume any liability for any damages arising from any errors etc. that may appear in this material. C. These materials are solely intended for a customer's individual use. Therefore, without the prior written approval of Panasonic, any other use such as reproducing, selling, or distributing this material to a third party, via the Internet or in any other way, is prohibited. 2001 MAR