SURFACE MOUNT ELECTROLYTIC - 85˚C DVCR Cylindrical leadless type for surface mounting SECTION 1 Low cost, general purpose, 2000 hours at 85° New expanded CV Range Anti-solvent (2 minutes) Designed for automatic mounting and reflow soldering SPECIFICATIONS Item Performance Category Temperature Range (°C) –40 to +85 Tolerance of Rated Capacity (%) ± 20 Leakage Current (µA) Less than 0.01CV or 3 whichever is larger (after 2min) C: rated capacitance (µF) Tangent of Loss Angle (tan∂) Rated Voltage (V) 4 tan∂ (max) Endurance (85°C) (Applied Ripple Current) Ø3 16 25 35 50 63 100 – – 0.42 0.30 0.24 0.22 0.16 0.14 0.12 Ø4 to Ø6.3 0.42 0.28 0.24 0.20 0.14 0.12 0.10 – – 0.12 0.10 0.10 0.10 Rated Voltage (V) Impedance 10 Ø3 Ø8 to Ø10 Characteristics at high and low temperatures 6.3 – 0.28 0.24 0.20 0.14 4 6.3 10 16 25 35 50 63 100 Z–25°C / Z+20°C 7 4 3 2 2 2 2 – – Z–40°C / Z+20°C 17 10 8 6 4 3 3 – – Ø4 to Ø6.3 Z–25°C / Z+20°C 7 3 3 2 2 2 2 – – Z–40°C / Z+20°C 15 8 5 4 3 3 3 – – Ø8 to Ø10 Z–25°C / Z+20°C – 4 3 2 2 2 2 2 2 Z–40°C / Z+20°C – 8 5 4 3 3 3 3 3 Test Time 2000 hours Leakage Current The initial specified value or less Percentage of Capacitance Change Within ±20% of initial value (4wv± 30%) Tangent of Loss Angle 200% or less of the initial specified value (4wv: 3000%) Shelf Life (85°C) Test Time: 1000 hours: other items are the same as those for endurance. JIS C5101-1 Applicable Standards JIS C5101-1, –18 1998 (IEC600384-1 1992, -18 1993) COEFFICIENT OF FREQUENCY FOR RATED RIPPLE CURRENT Frequency (Hz)/Rated Voltage 50-60 120 1k 10k - 100k 4 to 16 0.8 1 1.15 1.25 25 to 35 0.8 1 1.25 1.40 50 to 63 0.8 1 1.35 1.50 100 0.7 1 1.35 1.50 ORDERING INFORMATION DVCR 47 6.3 Range Capacitance µF Voltage LF Can Size Lead Free Small = Blank D8 = 8mm dia D10 = 10mm dia 73 www.dubilier.co.uk SURFACE MOUNT SMD - 85˚C REDUCED SIZE DVCR Part No. W.V (V.DC) Cap (uF) ESR Ripple Current Size (120Hz/+20C) (120Hz/+105C) dia/height max (mA) rms max Part No. W.V (V.DC) Cap (uF) ESR Ripple Current Size (120Hz/+20C) (120Hz/+105C) dia/height max (mA) rms max DVCR224-LF 4 22 32 14 3X5.5 DVCR2.235-LF 35 2.2 106 8 DVCR2204-LF 4 220 3.2 110 6.3X5.5 DVCR3.335-LF 35 3.3 70 9 3X5.5 DVCR4.735D4-LF 35 4.7 42 20 4X5.5 3X5.5 5X5.5 DVCR226.3D4-LF 6.3 22 21 31 4X5.5 DVCR1035-LF 35 10 20 34 DVCR336.3-LF 6.3 33 21 28 4X5.5 DVCR2235-LF 35 22 11 47 5X5.5 DVCR476.3-LF 6.3 47 15 34 4X5.5 DVCR3325-LF 35 33 7 67 6.3X5.5 DVCR1006.3-LF 6.3 100 7 58 5X5.5 DVCR4735-LF 35 47 4.9 54 6.3X5.5 DVCR1506.3-LF 6.3 150 4.6 83 6.3X5.5 DVCR6835-LF 35 68 3.4 109 6.3X8 DVCR2206.3-LF 6.3 220 2.6 88 6.3X5.3 DVCR10035-LF 35 100 2.3 120 6.3X8 DVCR3306.3-LF 6.3 330 2.1 139 6.3X8 DVCR22035-LF 35 220 0.91 458 10X10 DVCR4706.3-LF 6.3 470 0.99 252 8X10 DVCR10006.3-LF 6.3 1000 0.46 458 10X10 DVCR3.350-LF 50 3.3 50 19 4X5.5 DVCR4.750-LF 50 4.7 42 20 4X5.5 DVCR2210-LF 10 22 18 39 5X5.5 DVCR1050-LF 50 10 17 44 6.3X5.5 DVCR6810-LF 10 68 7.8 54 5X5.5 DVCR2250-LF 50 22 9 59 6.3X5.5 DVCR10010-LF 10 100 4 98 6.3X5.5 DVCR3350-LF 50 33 6 82 6.3X8 DVCR22010-LF 10 220 1.8 155 8X6.5 DVCR4750-LF 50 47 4.2 98 6.3X8 DVCR100010-LF 10 1000 0.34 458 10X10 DVCR10050-LF 50 100 1.7 458 10X10 DVCR1016-LF 16 10 37 18 3X5.5 DVCR163-LF 63 1 10 166 4X5.5 DVCR1016D4-LF 16 10 33 26 4X5.5 DVCR2263-LF 63 22 7.5 139 8X10 DVCR2216-LF 16 22 20 30 4X5.5 DVCR3363-LF 63 33 5 139 8X10 DVCR2216D5-LF 16 22 15 44 5X5.5 DVCR4763-LF 63 47 3.5 226 10X10 DVCR3316-LF 16 33 13 44 5X5.5 DVCR6863-LF 63 68 2.4 226 10X10 DVCR4716-LF 16 47 7.1 75 6.3X5.5 DVCR10063-LF 63 100 1.7 226 10X10 DVCR6816-LF 16 68 6.3 74 6.3X5.5 DVCR10016-LF 16 100 3.3 103 6.3X5.5 DVCR10100-LF 100 10 16.6 94 8X10 DVCR15016-LF 16 150 2.9 109 6.3X8 DVCR22100-LF 100 22 7.5 189 10X10 DVCR22016-LF 16 220 2 144 6.3X8 DVCR33100-LF 100 33 5 189 10X10 DVCR33016-LF 16 330 1 252 8X10 DVCR47016-LF 16 470 0.71 252 8X10 DVCR4.725-LF 25 4.7 57 11 3X5.5 DVCR1025-LF 25 10 30 23 4X5.5 25 22 14 43 5X5.5 25 33 9 54 5X5.5 DVCR4725-LF 25 47 6.4 75 6.3X5.5 DVCR6825-LF 25 68 4.4 90 6.3X5.5 DVCR10025-LF 25 100 3 124 6.3X8 DVCR22025-LF 25 220 1.1 252 8X10 DVCR33025-LF 25 330 0.7 458 10X10 DVCR47025-LF 25 470 0.49 458 10X10 OUTLINE DRAWING + L L A B I W P 3 5.3 +/- 0.2 3.3 3.3 1.5 0.45 to 0.75 0.8 4 5.3 +/- 0.2 4.3 4.3 2.0 0.5 to 0.8 1.0 5 5.3 +/- 0.2 5.3 5.3 2.3 0.5 to 0.8 1.5 6.3 5.3 +/- 0.2 6.6 6.6 2.7 0.5 to 0.8 2.0 8 6.5 +/- 0.3 8.4 8.4 3.4 0.5 to 0.8 2.3 8 10 +/- 0.5 8.4 8.4 3.0 0.7 to 1.1 3.1 10 10 +/- 0.5 10.4 10.4 3.3 0.7 to 1.1 4.7 W B DØ ØD B DØ 0.3 Ma x DVCR2225-LF DVCR3325-LF 0.3 Ma x SECTION 1 RANGE & CASE SIZE DØ X Lmm + I - L A W I 74 www.dubilier.co.uk I P 2.0 +/-0.5 P I SURFACE MOUNT TAPING SPECIFICATIONS FOR DVCR & DVJL + DVJR, DVJRHVX, DVCNP SECTION 1 TAPE SPECIFICATION 380 = 380mm real size 330 = 330mm real size 330/380 75 www.dubilier.co.uk