ML145040 ML145041 8-Bit A/D Converters With Serial Interface Silicon-Gate CMOS SEMICONDUCTOR TECHNICAL DATA Legacy Device: Motorola MC145040, MC145041 The ML145040 and ML145041 are low-cost 8-bit A/D Converters with serial interface ports to provide communication with microprocessors and microcomputers. The converters operate from a single power supply with a maximum nonlinearity of ± 1/2 LSB over the full temperature range. No external trimming is required. The ML145040 allows an external clock input (A/D CLK) to operate the dynamic A/D conversion sequence. The ML145041 has an internal clock and an end–of–conversion signal (EOC) is provided. • Operating Voltage Range: VDD = 4.5 to 5.5 Volts • Successive Approximation Conversion Time: ML145040 – 10 µs (with 2 MHz A/D CLK) ML145041 – 20 µs Maximum (Internal Clock) • 11 Analog Input Channels with Internal Sample and Hold • 0- to 5-Volt Analog Input Range with Single 5-Volt Supply • Ratiometric Conversion • Separate Vref and VAG Pins for Noise Immunity • Wide Vref Range • No External Trimming Required • Direct Interface to Motorola SPI and National MICROWIRE Serial Data Ports • TTL/NMOS–Compatible Inputs May be Driven with CMOS • Outputs are CMOS, NMOS or TTL Compatible • Very Low Reference Current Requirements • Low Power Consumption: 11 mW • Internal Test Mode for Self Test Page 1 of 12 www.lansdale.com P DIP 20 = RP CERAMIC PLASTIC CASE 732 CASE 738 SO 20W = -6P SOG CASE 751D CROSS REFERENCE/ORDERING INFORMATION PACKAGE MOTOROLA LANSDALE P DIP 20 MC145040P ML145040RP SO 20W MC145040DW ML145040-6P P DIP 20 MC145041P ML145041RP SO 20W MC145041DW ML145041-6P Note: Lansdale lead free (Pb) product, as it becomes available, will be identified by a part number prefix change from ML to MLE. Issue A LANSDALE Semiconductor, Inc. ML145040, ML145041 Page 2 of 12 www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145040, ML145041 Page 3 of 12 www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145040, ML145041 Page 4 of 12 www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145040, ML145041 Page 5 of 12 www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145040, ML145041 PIN DESCRIPTIONS DIGITAL INPUTS AND OUTPUTS CS (Pin 15) Active–low chip select input. CS provides three–state control of Dout. CS at a high logic level forces Dout to a high–impedance state. IN addition, the device recognizes the falling edge of CS as a serial interface reset to provide synchronization between the MPU and the A/D converter’s serial data stream. To prevent a spurious reset from occurring due to noise on the CS input, a delay circuit has been included such that a CS signal of duration ≤1 A/D CLK period (ML145040) or ≤500 ns (ML145041) is ignored. A valid CS signal is acknowledged when the duration is ≥3 A/D CLK periods (ML145040) or ≥3 µs (ML145041) CAUTION A reset aborts a conversion sequence, therefore high–to–low transitions on CS must be avoided during the conversion sequence. Dout (Pin 16) Serial data output of the A/D conversion result. The 8–bit serial data stream begins with the most significant bit and is shifted out on the high–to–low transition of SCLK. Dout is a three–state output as controlled by CS. However, Dout is forced into a high–impedance state after the eighth SCLK, independent of the state of CS. See Figures 9, 10, 11, or 12. Din (Pin 17) Serial data input. The 4–bit serial data stream begins with the most significant address bit of the analog mux and is shifted in on the low–to–high transition of SCLK. SCLK (Pin 18) Serial data clock. THe serial data register is completely static, allowing SCLK rates down to DC in a continuos or intermittent mode. SCLK need not be synchronous to the A/D CLK (ML145040) or the internal clock (ML145041). Eight SCLK cycles are required for each simultaneous data transfer, the low–to–high transition shifting in the new address and the high–to–low transition shifting out the previous conversion result. The address is acquired during the first four SCLK cycles, with the interval produced by the remaining four cycles being used to begin charging the on–chip sample–and–hold capacitors. After the eighth SCLK, the SCLK input is inhibited (on–chip) until the conversion is complete. A/D CLK (Pin 18, ML145040 only) A/D clock input. This pin clocks the dynamic A/D conversion sequence, and may be asynchronous and unrelated to SCLK. The signal must be free running, and may be obtained Page 6 of 12 from the MPU system clock. Deviations from a 50% duty cycle can be tolerated if each half period is > 238 ns. EOC (Pin 19, ML145041 only) End–of–conversion output. EOC goes low on the negative edge of the eighth SCLK. The low–to–high transition of EOC indicates the A/D conversion is complete and the data is ready for transfer. ANALOG INPUTS AND TEST MODE AN0 through AN10 (Pins 1-9, 11, 12) Analog multiplexer inputs. The input AN0 is addressed by loading $0 into the serial data input, Din. AN1 is addressed by $1, AN2 by $2…AN10 via $A. The mux features a break–before–make switching structure to minimize noise injection into the analog inputs. The source impedance driving these inputs must be ≤ 10 kΩ. NOTE: $B addresses an on–chip test voltage of (Vref + VAG)/2, and produces an output of $80 if the converter is functioning properly. However, a ± 1 LSB deviation from $80 occurs in the presence of sufficient system noise (external to the chip) on VDD, VSS, Vref or VAG. POWER AND REFERENCE PINS VSS and VDD (Pins 10 and 20) Device supply pins. VSS is normally connected to digital ground; VDD is connected to a positive digital supply voltage. VDD – VSS variations over the range of 4.5 to 5.5 volts do not affect the A/D accuracy. Excessive inductance in the VDD or VSS lines as on automatic test equipment, may cause A/D offsets > 1/2 LSB. VAG and Vref (Pins 13 and 14) Analog reference voltage pins which determine the lower and upper boundary of the A/D conversion. Analog input voltages ≥ Vref produce an output of $FF and input voltages ≤ VAG produce an output of $00. CAUTION: THe analog input voltage must be ≥ VSS and ≤ VDD. The A/D conversion result is ratiometric to Vref – VAG as shown by the formula: Vref and VAG should be as noise–free as possible to avoid degradation of the A/D conversion. Noise on either of these pins will couple 1:1 to the analog input signal i.e. a 20 mV change in Vref can cause a 20 mV error in the conversion result. Ideally Vref and VAG should be single-point connected to the voltage supply driving the system’s transducers. www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145040, ML145041 Page 7 of 12 www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145040, ML145041 Page 8 of 12 www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145040, ML145041 Legacy Applications Information DESCRIPTION This example application of the ML145040/ML145041 ADCs interfaces three controllers to a microprocessor and processes data in real–time for a video game. The standard joystick X–axis (left/right) and Y–axis (up/down) controls as well as engine thrust controls are accommodated Figure 13 illustrates how the ML145040/ML145041 is used as a cost–effective means to simplify this type of circuit design. Utilizing one ADC, three controllers are interfaced to a CMOS or NMOS microprocessor with a serial peripheral interface (SP) port. Processors with National Semiconductor’s MICROWIRE serial port may also be used. Full duplex operation optimizes throughput for this system. DIGITAL DESIGN CONSIDERATIONS Motorola’s MC68HC05C4 CMOS MCU may be chosen to reduce power supply size and cost. The NMOS MCUs may be used if power consumption is not critical. A VDD to VSS 0.1 µF bypass capacitor should be closely mounted to the ADC. Both the ML145040 and ML145041 will accommodate all the analog system inputs. The ML145040, when used with a 2 MHz MCU, takes 24 µs to sample the analog input, perform the conversion, and transfer the serial data at 1 MHz. Thirty–two A/D Clock cycles (2 MHz at input pin 19) must be provided and counted by the MCU after the eighth SCLK before reading the ADC results. The ML145041 has the end–of–conversion (EOC) signal (at output pin 19) to define when data is ready, but has a slower 40 µs cycle time. However, the 40 µs is constant for serial data rates of 1 MHz independent of the MCU clock frequency. Therefore, the ML145041 may be used with CMOS MCU operating at the reduced clock rates to minimize power consumption without sacrificing ADS cycle times, with EOC being used to generate an interrupt. The ML145041 may also be used with MCU’s which do not provide a system clock.) ANALOG DESIGN CONSIDERATIONS Controllers with output impedances of less than 10 kilohms Page 9 of 12 may be direcly interfaced to these ADCs, eliminating the need for buffer amplifiers. Separate lines connect the Vref and VAG pins on the ADC with the controllers to provide isolation from system noise. Although not indicated in Figure 13, the Vref and controller ouput lines may need to be shielded, depending on their length and electrical environment. This should be verified during prototyping with an oscilloscope. If shielding is required, a twisted pair or foil–shielded wire (not coax) is appropriate for this low frequency application. One wire of the pair of the shield must be VAG. A reference circuit voltage of 5 volts is used for this application. The reference circuitry may be as simple as tying VAG to system ground and Vref to the system’s positive supply. (See Figure 14.) However, the system power supply noise may require that a seperate supply be used for the voltage reference. This supply must provide source current for Vref as well as current for the controller potentionmeters. A bypass capacitor across the Vref and VAG pins is recommended. These pins are adjacent on the ADC package which facilitates mounting the capacitor very close to the ADC. SOFTWARE CONSIDERATIONS The software flow for acquisition is straightforward. The nine analog inputs, AN0 through AN8, are scanned by reading the analog value of the previously addressed channel into the MCU and sending the address of the next channel to to be read to the ADC, simultaneously. All nine inputs may be scanned in a minimum of 216 µs (ML145040) or 360 µs (ML145041). If the design in realized using the ML145040, 32 A/D clock cycles (at pin 19) must be counted by the MCU to allow time for A/D conversion. The designer utilizing the ML145041 has the end–of–conversion signal (at pin 19) to define the conversion interval. EOC may be used to generated an interrupt, which is serviced by reading the serial data from the ADC. The software flow should then process and format the data, and transfer the information to the video circuitry for updating the display. www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145040, ML145041 Legacy Applications Information Page 10 of 12 www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145040, ML145041 OUTLINE DIMENSIONS P DIP 20 = RP (ML145040RP, ML145041RP) CASE 738-03 -A20 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 11 B 1 1 0 C -T- L K SEATING PLANE M E G N F J 20 PL 0.25 (0.010) D 20 PL 0.25 (0.010) Page 11 of 12 M T A M www.lansdale.com M T B M DIM A B C D E F G J K L M N INCHES MIN MAX 1.070 1.010 0.260 0.240 0.180 0.150 0.022 0.015 0.050 BSC 0.070 0.050 0.100 BSC 0.015 0.008 0.140 0.110 0.300 BSC 15° 0° 0.020 0.040 MILLIMETERS MIN MAX 27.17 25.66 6.60 6.10 4.57 3.81 0.55 0.39 1.27 BSC 1.77 1.27 2.54 BSC 0.38 0.21 3.55 2.80 7.62 BSC 15° 0° 1.01 0.51 Issue A LANSDALE Semiconductor, Inc. ML145040, ML145041 OUTLINE DIMENSIONS SOG 20W = -6P (ML145040-6P, ML145041-6P) CASE 751D-04 -A20 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.150 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOW ABLE DAMBAR PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF D DIMENSION AT MAXIMUM MATERIAL CONDITION. 11 -B- P 10 PL 0.010 (0.25) 1 1 B M 0 D 20 PL 0.010 (0.25) M M T B S A S J F R X 45° C -TG 18 PL K SEATING PLANE M DIM A B C D F G J K M P R MILLIMETERS MIN MAX 12.65 12.95 7.60 7.40 2.35 2.65 0.49 0.35 0.90 0.50 1.27 BSC 0.32 0.25 0.25 0.10 7° 0° 10.05 10.55 0.75 0.25 INCHES MIN MAX 0.499 0.510 0.292 0.299 0.093 0.104 0.014 0.019 0.020 0.035 0.050 BSC 0.010 0.012 0.004 0.009 0° 7° 0.395 0.415 0.010 0.029 Lansdale Semiconductor reserves the right to make changes without further notice to any products herein to improve reliability, function or design. Lansdale does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. “Typical” parameters which may be provided in Lansdale data sheets and/or specifications can vary in different applications, and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by the customer’s technical experts. Lansdale Semiconductor is a registered trademark of Lansdale Semiconductor, Inc. Page 12 of 12 www.lansdale.com Issue A