FPL31PT CHENMKO ENTERPRISE CO.,LTD THRU SURFACE MOUNT GLASS PASSIVATED SUPER FAST SILICON RECTIFIER VOLTAGE RANGE 50 - 1000 Volts CURRENT 3.0 Amperes FPL37PT FEATURE *Sm al l S u r f ac e M o u n t i n g T y p e. (SMP) * Low leakage current * Fast recovery times for high efficiency * Glass passivated junction * High temperature soldering guaranteed : 260oC/10 seconds at terminals SMP 0.081 (2.05) 0.077 (1.95) 0.170 (4.31) 0.163 (4.15) (3) (1) (2) 0.019 (0.50 Min.) 0.077 (1.95) 0.073 (1.85) 0.045 (1.16) 0.042 (1.07) 0.005 (0.15 Min.) 0.019 (0.50 Min.) 0.264 (6.70) 0.254 (6.46) CIRCUIT 2 0.212 (5.38) 0.208 (5.29) 1 0.055 (1.40) 0.051 (1.30) SMP Dimensions in inches and (millimeters) 3 MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) FPL33PT FPL34PT FPL35PT FPL36PT FPL37PT UNITS Maximum Recurrent Peak Reverse Voltage RATINGS SYMBOL VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 Volts o FPL31PT FPL32PT IO 3.0 Amps IFSM 100 Amps CJ 65 pF TJ, TSTG -65 to +150 Maximum Average Forward Rectified Current TL = 100 C Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range o C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS SYMBOL Maximum Instantaneous Forward Voltage at 3.0 A DC Maximum DC Reverse Current @ TA = 25oC at Rated DC Blocking Voltage @ TA = 100oC Maximum Reverse Recovery Time (Note 2) NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts 2. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A FPL31PT FPL32PT FPL33PT VF FPL34PT FPL35PT FPL36PT FPL37PT UNITS 1.3 Volts 5.0 uAmps IR 50 trr 150 uAmps 250 500 nSec 2004-7 RATING CHARACTERISTIC CURVES ( FPL31PT THRU FPL37PT ) 3.0 2.5 2.0 1.5 1.0 Single Half Wave 60HZ Resistive or Inductive Load 0.5 0 0 25 50 75 100 125 LEAD TEMPERATURE, ( oC ) 150 175 PEAK FORWARD SURGE CURRENT, ( A ) AVERAGE FORWARD CURRENT, (A) FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 140 120 8.3ms Single Half Sine-Wave (JEDEC Method) 100 80 60 40 20 0 1 FIG. 3 - TYPICAL REVERSE CHARACTERISTICS PER BRIDGE ELEMENT 5 10 20 NUMBER OF CYCLES AT 60 Hz 50 100 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 20 INSTANTANEOUS FORWARD CURRENT, ( A ) 100 TJ =100oC 10 1.0 TJ =25oC .1 10 Pulse Width = 300uS 1% Duty Cycle 3.0 1.0 0.3 TJ =25oC 0.1 .03 .01 .01 0 20 40 60 80 100 120 140 0 PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) 0.3 0.5 0.7 FIG. 5 - TYPICAL JUNCTION CAPACITANCE 100 60 40 20 10 TJ =25oC 6 4 2 1 .1 .2 .4 0.9 1.1 1.3 1.5 INSTANTANEOUS FORWARD VOLTAGE, ( V ) 200 JUNCTION CAPACITANCE, ( pF ) INSTANTANEOUS REVERSE CURRENT, (uA) 2 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) 40 100 1.7