Maxim MAX5092AATE+ 4v to 72v input ldos with boost preregulator Datasheet

19-0659; Rev 0; 10/06
KIT
ATION
EVALU
E
L
B
AVAILA
4V to 72V Input LDOs with Boost Preregulator
Features
The MAX5092A/MAX5092B/MAX5093A/MAX5093B lowquiescent-current, low-dropout (LDO) regulators contain
simple boost preregulators operating at a high frequency.
The devices seamlessly provide a preset 3.3V
(MAX5092A/MAX5093A) or 5V (MAX5092B/MAX5093B)
LDO output voltage from an automotive cold-crank
through load-dump (3.5V to 80V) input voltage conditions. The MAX5092_/MAX5093_ deliver up to 250mA
with excellent load and line regulation. During normal
operation, when the battery is healthy, the boost preregulator is completely turned off, reducing quiescent current
to 65µA (typ). This makes the devices suitable for
always-on power supplies.
The buck-boost operation achieved by this combination
of LDO and boost preregulator offers the advantage of
using a single off-the-shelf inductor in place of the multiple-winding custom magnetics needed in typical single-ended primary inductor converter (SEPIC) and
transformer-based flyback topologies. The high operating frequency of the boost regulator significantly
reduces component size. The MAX5092_ integrates a
blocking diode to further reduce the external component count. The boost preregulator output voltage is
preset to 7V. Both LDO and boost output voltages are
programmable using external resistors. The boost preregulator output voltage is adjustable up to 11V
(MAX5092_), or up to 12V (MAX5093_). The LDO output
voltage is adjustable from 1.5V to 9V (MAX5092_) or
from 1.5V to 10V (MAX5093_).
The devices feature a shutdown mode with 5µA (typ)
shutdown current, a HOLD input to implement a self-holding circuit, and a power-on-reset output (RESET) with an
externally programmable timeout period. Additional features include output overload, short-circuit, and thermal
protection.
The MAX5092_/MAX5093_ are available in a thermally
enhanced, 16-pin 5mm x 5mm thin QFN package and can
dissipate up to 2.7W at +70°C on a multilayer PC board.
♦ Wide Operating Input Voltage Range: 3.5V to 72V
with a 4V Startup Voltage
♦ LDO Output Regulates to 5V Seamlessly from an
Input Voltage of 3.5V to 72V
♦ Up to 250mA Output Current
♦ Preset 3.3V, 5V, or Externally Programmable LDO
Output Voltage from 1.5V to 9V (MAX5092_) or
from 1.5V to 10V (MAX5093_)
♦ Preset 7V or Externally Programmable Boost
Output Voltage Up to 11V (MAX5092_) or Up to
12V (MAX5093_)
♦ 65µA Quiescent Current in LDO Mode (VIN ≥8V)
♦ 5µA Shutdown Current
♦ Power-On Reset (RESET) with Programmable
Timeout Period
♦ Output Short-Circuit and Thermal Protection
♦ TQFN Package Capable of Dissipating Up to 2.7W
at +70°C
Ordering Information
PART
TEMP RANGE
PINPACKAGE
PKG
CODE
MAX5092AATE+* -40°C to +125°C 16 TQFN-EP**
MAX5092BATE+
T1655-3
-40°C to +125°C 16 TQFN-EP**
T1655-3
MAX5093AATE+* -40°C to +125°C 16 TQFN-EP**
T1655-3
MAX5093BATE+
T1655-3
-40°C to +125°C 16 TQFN-EP**
+Denotes lead-free package.
*Future product—contact factory for availability.
**EP = Exposed pad.
LX
LX
BSOUT
TOP VIEW
PGND_BST
Pin Configuration
12
11
10
9
BSFB 13
8
OUT
7
OUT_SENSE
6
SET
5
PGND_LDO
Applications
VL 14
Automotive—Body Electronics
+
IN
1
Typical Operating Circuit and Selector Guide appear at end
of data sheet.
2
3
4
HOLD
RESET 16
SGND
Industrial
CT 15
EN
Automotive—ECU
MAX5092_/
MAX5093_
THIN QFN
(5mm x 5mm)
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX5092/MAX5093
General Description
MAX5092/MAX5093
4V to 72V Input LDOs with Boost Preregulator
ABSOLUTE MAXIMUM RATINGS
IN, EN, LX, BSOUT to SGND..................................-0.3V to +80V
PGND_BST, PGND_LDO to SGND .......................-0.3V to +0.3V
VL, RESET, OUT, OUT_SENSE to SGND ...............-0.3V to +12V
BSOUT to LX (MAX5092_)......................................-0.3V to +12V
SET, BSFB, CT to SGND ..........................................-0.3V to +6V
HOLD to SGND….....................................-0.3V to (VOUT + 0.3V)
OUT Current (IOUT) Short Circuit to PGND_LDO,
(VIN ≤ 28V) ..............................................................Continuous
RESET Sinking Current .........................................................5mA
Continuous Power Dissipation (TA = +70°C)
16-Pin Thin QFN (derate 33.3mW/°C
above +70°C)...............................................2666mW (Note 1)
Operating Temperature Range .........................-40°C to +125°C
Maximum Junction Temperature .....................................+150°C
Storage Temperature Range .............................-60°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Note 1: As per JEDEC Standard 51 (Multilayer Board).
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VIN = VEN = 14V, IOUT = 1mA, CIN = 47µF, CBSOUT = 22µF, COUT = 10µF, CVL = 1µF, TA = TJ = -40°C to +125°C, unless otherwise
noted. See Figures 4–7 as applicable. Typical specifications are at TA = +25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
72
V
INPUT SUPPLY
Input Voltage Range
Internal Input Undervoltage
Lockout
Supply Current (Boost Converter
Off)
Supply Current (Boost Converter
On)
Shutdown Supply Current
VIN
(Note 3)
4
VUVLOF
VIN falling
3.0
3.2
3.4
VUVLOR
VIN rising
3.4
3.6
3.8
65
85
LDO mode, IOUT = 250mA
70
100
VIN = 5V
0.4
1.0
mA
6
10
µA
IQ
IS
LDO mode,
IOUT = 100µA
ISHDN
VEN ≤ +0.4V
IBSOUT
VIN = 4V
VBST_DIS
VIN rising
TJ = -40°C to +125°C
(Note 4)
TJ = -40°C to +125°C
(Note 4)
V
µA
BOOST CONVERTER
Minimum BSOUT Output Current
Boost Converter Disable
Threshold
250
7.5
Boost Converter Disable
Threshold Hysteresis
BSOUT Output Voltage
Maximum BSOUT Output Voltage
VBSOUT
VBSOUT(MAX)
VBSFB
BSFB Input Bias Current
IBSFB
Boost Internal Switch Minimum
Off-Time
2
8.5
0.5
BSFB Regulation Voltage
Boost Internal Switch
On-Resistance
8.0
mA
VIN = 4V, BSFB = SGND
6.65
MAX5092_
11
MAX5093_
12
1.18
RDS(ON)
tOFF
7.00
0.80
1.24
V
V
7.35
V
V
1.30
V
100
nA
0.5
1.2
Ω
1
1.25
µs
_______________________________________________________________________________________
4V to 72V Input LDOs with Boost Preregulator
(VIN = VEN = 14V, IOUT = 1mA, CIN = 47µF, CBSOUT = 22µF, COUT = 10µF, CVL = 1µF, TA = TJ = -40°C to +125°C, unless otherwise
noted. See Figures 4–7 as applicable. Typical specifications are at TA = +25°C.) (Note 2)
PARAMETER
Boost Internal Switch Maximum
On-Time
Internal Switch Current Limit
SYMBOL
tON-MAX
ILIM
Measured in steady-state condition
MIN
TYP
MAX
UNITS
1.80
2.25
2.70
µs
3.0
A
5
µs
1.5
Time from VBSOUT falling below regulation
to switch on-time
Boost Turn-On Response Time
Internal Diode Forward Voltage
Drop
CONDITIONS
VF
2
MAX5092_ only, IF = 1A
0.95
V
LDO
Guaranteed Output Current
Output Voltage
IOUT
VBSOUT - VOUT = 2V (Note 5)
Maximum Adjustable Output
Voltage
mA
SET = SGND,
MAX5092A/
MAX5093A
3.25
3.3
3.35
100µA ≤ IOUT ≤ 250mA
3.2
3.3
3.4
SET = SGND,
MAX5092B/
MAX5093B
IOUT = 1mA
4.900
5
5.075
100µA ≤ IOUT ≤ 250mA
4.85
5
5.10
VOUT
Minimum Adjustable Output
Voltage
250
IOUT = 1mA
VADJMIN
Boost operation, VIN = 4V, VBSOUT = 7V
VADJMAX
Boost operation,
VIN = 4V
1.5
MAX5092_,
VBSOUT = 11V
9
MAX5093_,
VBSOUT = 12V
10
VADJ
LDO operation, VIN ≥ VBST_DIS
(boost converter off) (Note 6)
Dropout Voltage
∆VDO
IOUT = 250mA (Note 7)
0.9
Rising edge of VBSOUT to the rising edge of
VOUT, RL = 500Ω, SET = SGND
200
∆VOUT /
∆VIN
Line Regulation
SET Reference Voltage
SET Input Bias Current
Power-Supply Rejection Ratio
Short-Circuit Current
1.5
MAX5092A/MAX5093A
MAX5092B/MAX5093B
ISET
ISC
V
1.6
V
µs
0.5
mV/V
1.235
1.265
V
0.5
100
nA
0.2
0.6
mV/mA
1.6
1.205
IOUT = 1mA to 250mA
f = 100Hz
IOUT = 10mA, VBSOUT(AC)
= 500mVP-P, VOUT = 5V
80
f = 1MHz
IOUT = 10mA, VBSOUT(AC)
= 500mVP-P, VOUT = 5V
60
PSRR
10.0
0.4
7V ≤ VIN ≤ 28V, ILOAD = 250mA
VSET
∆VOUT /
∆IOUT
Load Regulation
7V ≤ VIN ≤ 72V,
ILOAD = 10mA
V
V
Adjustable Output Voltage
LDO Startup Response Time
V
dB
255
490
mA
_______________________________________________________________________________________
3
MAX5092/MAX5093
ELECTRICAL CHARACTERISTICS (continued)
MAX5092/MAX5093
4V to 72V Input LDOs with Boost Preregulator
ELECTRICAL CHARACTERISTICS (continued)
(VIN = VEN = 14V, IOUT = 1mA, CIN = 47µF, CBSOUT = 22µF, COUT = 10µF, CVL = 1µF, TA = TJ = -40°C to +125°C, unless otherwise
noted. See Figures 4–7 as applicable. Typical specifications are at TA = +25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
ENABLE, HOLD and RESET
EN High Input Threshold
ENH
EN Low Input Threshold
ENL
EN Input Bias Current
IEN
HOLD Low Input Threshold
VIL
HOLD Release Voltage
VIH
2.4
V
0.25
Regulator on, EN transition from high to low
EN = low
0.4
V
2
µA
0.4
V
VOUT 0.4
V
HOLD Pullup Current
IHOLD
Internally connected to OUT
RESET Voltage Threshold
VRESET
% of VOUT, VOUT falling
RESET Threshold Hysteresis
VRHYST
% of VOUT
RESET Output Low Voltage
VRL
ISINK = 1mA
0.4
V
RESET Output High Leakage
Current
IRH
V R ESET = 5V
1
µA
4
87
90
µA
92
2
%
%
RESET Output Minimum Timeout
Period
CCT not connected
25
µs
EN to RESET Minimum Timeout
Delay
CCT not connected
260
µs
Delay Comparator Threshold
(Rising)
VCTTH
Delay Comparator Threshold
Hysteresis
VCTTH-HYS
CT Charge Current
ICT-CHG
CT Discharge Current
ICT-DIS
1.205
1.24
1.265
100
1.5
2
5
V
mV
2.5
µA
mA
Limits at -40°C are guaranteed by design and characterization; not production tested.
Guaranteed minimum operating voltage is 3.5V on VIN falling only.
Guaranteed by design and not production tested.
The continuous maximum output current from the LDO is guaranteed according to the maximum power dissipation imposed
by the package thermal constraints.
Note 6: Maximum output adjustable value is conditioned by the maximum adjustable BSOUT Output Voltage Range minus the maximum dropout across the pass transistor.
Note 7: Dropout voltage is defined as (VBSOUT - VOUT) when VOUT is 2% below the value of VOUT for VBSOUT = VOUT + 2V.
Note 2:
Note 3:
Note 4:
Note 5:
4
_______________________________________________________________________________________
4V to 72V Input LDOs with Boost Preregulator
INPUT CURRENT (IIN)
vs. INPUT VOLTAGE (MAX5092B)
INPUT CURRENT (mA)
IOUT = 10mA
75
70
65
IOUT = 10mA
IOUT = 100µA
1
60
BOOST CONVERTER NOT SWITCHING,
QUIESCENT SUPPLY CURRENT = IIN - IOUT
0.1
50
16
24
32
40
48
56
IOUT = 10mA
70
60
IOUT = 100µA
50
4.5
5.0
5.5
6.0
6.5
7.0
-40
-15
10
35
60
85
INPUT VOLTAGE (V)
TEMPERATURE (°C)
QUIESCENT SUPPLY CURRENT
vs. TEMPERATURE (MAX5093B)
SHUTDOWN SUPPLY CURRENT
vs. INPUT VOLTAGE (MAX5092B)
SHUTDOWN SUPPLY CURRENT
vs. INPUT VOLTAGE (MAX5093B)
80
70
IOUT = 10mA
60
IOUT = 100µA
50
6
4
2
MAX5092/93 toc06
8
8
6
4
2
VEN = 0V
VEN = 0V
40
0
0
-15
10
35
60
85
135
110
4
TEMPERATURE (°C)
14
24
34
44
54
64
74
4
14
24
34
44
54
64
74
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
SHUTDOWN SUPPLY CURRENT
vs. TEMPERATURE (MAX5092B)
LINE-TRANSIENT RESPONSE
(VIN STEP FROM 4V TO 7V)
MAX5092/93 toc08
MAX5092/93 toc07
10
SHUTDOWN SUPPLY CURRENT (µA)
135
10
SHUTDOWN SUPPLY CURRENT (µA)
10
MAX5092/93 toc04
BOOST CONVERTER NOT SWITCHING,
QUIESCENT SUPPLY CURRENT = IIN - IOUT
-40
110
INPUT VOLTAGE (V)
100
90
80
40
4.0
72
64
SHUTDOWN SUPPLY CURRENT (µA)
8
BOOST CONVERTER NOT SWITCHING,
QUIESCENT SUPPLY CURRENT = IIN - IOUT
90
BOOST CONVERTER SWITCHING
MAX5092/93 toc05
55
QUIESCENT SUPPLY CURRENT (µA)
10
100
MAX5092/93 toc03
IOUT = 100µA
MAX5092/93 toc02
85
80
100
MAX5092/93 toc01
QUIESCENT SUPPLY CURRENT (µA)
90
QUIESCENT SUPPLY CURRENT
vs. TEMPERATURE (MAX5092B)
QUIESCENT SUPPLY CURRENT (µA)
QUIESCENT SUPPLY CURRENT
vs. INPUT VOLTAGE (MAX5092B)
8
IOUT = 250mA
VOUT
50mV/div
5V (AC-COUPLED)
7V
6
VIN
1V/div
4V
4
-40
-15
10
35
60
85
110
7V (AC-COUPLED)
VBSOUT
1V/div
VEN = 0V
2
135
200µs/div
TEMPERATURE (°C)
_______________________________________________________________________________________
5
MAX5092/MAX5093
Typical Operating Characteristics
(VIN = VEN = 14V, CIN = 47µF, CBSOUT = 22µF, COUT = 10µF, CVL = 1µF, TA = +25°C, unless otherwise noted.) (See Figures 4–7 as
applicable.)
Typical Operating Characteristics (continued)
(VIN = VEN = 14V, CIN = 47µF, CBSOUT = 22µF, COUT = 10µF, CVL = 1µF, TA = +25°C, unless otherwise noted.) (See Figures 4–7 as
applicable.)
LINE-TRANSIENT RESPONSE
(VIN STEP FROM 3.5V TO 72V)
LINE-TRANSIENT RESPONSE
(VIN STEP FROM 3.5V TO 14V)
MAX5092/93 toc09
MAX5092/93 toc10
IOUT = 5mA
VIN
50V/div
72V
VOUT
100mV/div
3.5V
5V (AC-COUPLED)
14V
VOUT
50mV/div
5V (AC-COUPLED)
VBSOUT
5V/div
7V
14V
72V
VBSOUT
50V/div
VIN
5V/div
3.5V
7V
40ms/div
200µs/div
LDO OUTPUT VOLTAGE
vs. LDO LOAD CURRENT (MAX5092B)
600
400
TA = -40°C: CIN = 10µF, CBSOUT = 4.7µF, COUT = 10µF
(CERAMIC)
TA = +25°C, +135°C: CIN = 47µF, CBSOUT = 22µF
(ELECTROLYTIC), COUT = 10µF (CERAMIC)
5.10
200
5.05
TA = +25°C, VIN = 4V
TA = +25°C, VIN = 14V
5.00
MAX5092/93 toc13
0
VIN = 14V, IOUT = 10mA
PSRR (dB)
800
5.15
POWER-SUPPLY REJECTION RATIO
vs. FREQUENCY
MAX5092/93 toc12
1000
LDO OUTPUT VOLTAGE (V)
MAX5092/93 toc11
DROPOUT VOLTAGE (VBSOUT - VOUT)
vs. LDO LOAD CURRENT
DROPOUT VOLTAGE (mV)
TA = -40°C, VIN = 4V
TA = -40°C, VIN = 14V
4.95
10dB/div
-70
4.90
TA = +135°C, VIN = 4V
TA = +135°C, VIN = 14V
4.85
0
0
50
100
150
200
0
250
100
300
200
100
1k
LDO LOAD CURRENT (mA)
LDO LOAD CURRENT (mA)
100k
STARTUP THROUGH INPUT VOLTAGE
MAX5092/93 toc15
MAX5092/93 toc14
0
10k
FREQUENCY (Hz)
POWER-SUPPLY REJECTION RATIO
vs. FREQUENCY
IOUT = 250mA
VIN = 8V, IOUT = 10mA
VIN
10V/div
0V
VBSOUT
10V/div
PSRR (dB)
MAX5092/MAX5093
4V to 72V Input LDOs with Boost Preregulator
0V
10dB/div
ILX
5A/div
-70
0A
VOUT
5V/div
100
1k
10k
100k
1M
0V
100µs/div
FREQUENCY (Hz)
6
_______________________________________________________________________________________
1M
4V to 72V Input LDOs with Boost Preregulator
STARTUP THROUGH ENABLE
SHUTDOWN THROUGH VIN
MAX5092/93 toc17
MAX5092/93 toc16
IOUT = 250mA
VIN
10V/div
0V
VBSOUT
10V/div
VIN
10V/div
14V
VBSOUT
10V/div
14V
VOUT
5V/div
0V
0V
ILX
1A/div
0A
VOUT
5V/div
0V
VEN
2V/div
IOUT = 250mA
0V
200µs/div
2ms/div
SHUTDOWN THROUGH ENABLE
RESET TIMING RESPONSE
MAX5092/93 toc18
MAX5092/93 toc19
VIN
10V/div
14V
VBSOUT
10V/div
14V
VOUT
2V/div
IOUT = 250mA
CT = 680pF
0V
VRESET
2V/div
VOUT
5V/div
0V
0V
VEN
2V/div
VEN
2V/div
IOUT = 250mA
0V
0V
200µs/div
200µs/div
VOUT vs. TEMPERATURE
VOUT vs. TEMPERATURE
(MAX5092B)
3.34
MAX5092/93 toc21
5.10
MAX5092/93 toc20
3.36
5.05
VOUT (V)
VOUT (V)
3.32
3.30
5.00
3.28
4.95
3.26
IOUT = 10mA, R5 = 100kΩ,
R4 = 165kΩ, FIGURE 6
IOUT = 1mA, VSET = 0V
3.24
4.90
-40
-15
10
35
60
85
TEMPERATURE (°C)
110
135
-40
-15
10
35
60
85
110
135
TEMPERATURE (°C)
_______________________________________________________________________________________
7
MAX5092/MAX5093
Typical Operating Characteristics (continued)
(VIN = VEN = 14V, CIN = 47µF, CBSOUT = 22µF, COUT = 10µF, CVL = 1µF, TA = +25°C, unless otherwise noted.) (See Figures 4–7 as
applicable.)
Typical Operating Characteristics (continued)
(VIN = VEN = 14V, CIN = 47µF, CBSOUT = 22µF, COUT = 10µF, CVL = 1µF, TA = +25°C, unless otherwise noted.) (See Figures 4–7 as
applicable.)
LDO LOAD-TRANSIENT RESPONSE
(MAX5092B)
INPUT-VOLTAGE STEP RESPONSE
MAX5092/93 toc23
MAX5092/93 toc22
IOUT = 5mA
VOUT
20mV/div
VOUT
50mV/div
5V (AC-COUPLED)
(AC-COUPLED)
72V
VIN
20V/div
IOUT
100mA/div
0mA
3.5V
2ms/div
200ms/div
ENABLE AND HOLD TIMING
INTERNAL BOOST DIODE FORWARD DROP
(MAX5092)
MAX5092/93 toc24
MAX5092/93 toc25
1500
1250
VEN
5V/div
DIODE VOLTAGE (mV)
0V
VHOLD
5V/div
0V
VOUT
5V/div
1000
750
500
250
0V
VIN = 8V, BOOST CONVERTER
NOT SWITCHING
0
0
200ms/div
0.5
1.0
1.5
2.0
2.5
3.0
DIODE CURRENT (A)
0.4
TA = +25°C: VIN = 3.5V
VIN = 4V
VIN = 5V
0.2
0.8
0.6
VIN = 3.5V
0.4
VIN = 5V
50
100
150
200
IOUT (mA)
250
300
350
TA = TJ = +125°C
TA = TJ = -40°C
35
30
25
20
15
10
5
0
0
40
MAX5092/93 toc27
VIN = 4V
0.2
0
8
GROUND CURRENT DISTRIBUTION
(162 UNITS TESTED)
NUMBER OF UNITS
0.6
TA = +105°C: VIN = 4V
VIN = 5V
VIN = 3.5V
1.0
POWER LOSS (W)
TA = +105°C: VIN = 3.5V
VIN = 4V
VIN = 5V
0.8
1.2
MAX5092/93 toc26
1.0
BOOST CONVERTER POWER LOSS
(VBSOUT = 11V)
0
0
50
100
150
200
IOUT (mA)
250
300
350
52
54
56
58 60
62
IGND (µA)
_______________________________________________________________________________________
64
66
68 70
MAX5092/93 toc28
BOOST CONVERTER POWER LOSS
(VBSOUT = 7V)
POWER LOSS (W)
MAX5092/MAX5093
4V to 72V Input LDOs with Boost Preregulator
4V to 72V Input LDOs with Boost Preregulator
PIN
NAME
FUNCTION
1
IN
Input Supply Voltage. Bypass IN to the power ground plane with a 47µF (low-ESR) aluminum electrolytic
capacitor in parallel with a 1µF ceramic capacitor placed as close to the IC as possible.
2
EN
Enable Input. Drive EN high to turn on the IC. Drive EN low to disable the IC. Connect EN directly to IN for
always-on operation.
3
SGND
Signal Ground. Connect SGND to the signal ground plane and the exposed paddle. Connect the power
ground and signal ground plane together at the negative terminal of the input capacitor(s).
4
HOLD
Output Hold. When HOLD is forced low, the regulator stores the on-state of the output, allowing the
regulator to remain enabled even if EN is pulled low. To shut down the regulator, release HOLD after EN is
pulled low. If HOLD is unused, either connect HOLD to OUT or leave unconnected. HOLD is internally
connected to OUT through a 4µA pullup current.
5
PGND_LDO
6
7
8
LDO Power Ground. Connect PGND_LDO to the power ground plane. Connect the PGND_LDO ground and
signal ground plane together.
Feedback Input for the LDO. Connect SET directly to SGND to set the output voltage of the LDO to the
preset voltage of 3.3V (MAX5092A/MAX5093A) or 5V (MAX5092B/MAX5093B). Connect SET to the center
tap of a resistor-divider connected between the LDO output and SGND to set the output voltage. VSET
regulates to 1.24V when using an adjustable output.
SET
OUT_SENSE LDO Regulator Output Sense. Connect OUT_SENSE to OUT at the output capacitor near the load.
LDO Regulator Output. Bypass OUT to the power ground plane with a 10µF ceramic capacitor. VOUT
regulates to a preset voltage of 3.3V (MAX5092A/MAX5093A) or 5V (MAX5092B/MAX5093B), or is
adjustable from 1.5V to 9V (MAX5902_) or 1.5V to 10V (MAX5093_).
OUT
Boost Regulator Output Voltage. Bypass BSOUT to the PGND_BST ground plane with a 22µF (low-ESR)
aluminum electrolytic capacitor in parallel with a 1µF ceramic capacitor placed as close to the IC as
possible. Connect BSFB directly to SGND to regulate the BOOST output to a fixed voltage of 7V for VIN ≤
7V. VBSOUT follows VIN for VIN > 7V. VBSOUT is programmable up to 11V (MAX5092_) or 12V (MAX5093_)
by connecting BSFB to the center tap of an external resistor-divider connected between the BOOST output
and PGND_BST.
9
BSOUT
10, 11
LX
12
PGND_BST
Boost Regulator Power Ground. Connect PGND_BST to the power ground plane. Connect the PGND_BST
ground plane and the signal ground plane together at the negative terminal of the input capacitor(s).
13
BSFB
Feedback Input for the Boost Regulator. Connect BSFB directly to SGND to set the boost regulator output
voltage to 7V. Connect BSFB to the center tap of an external resistor-divider connected between BSOUT
and SGND to set the output voltage. VBSFB regulates to 1.24V when using an adjustable output.
14
VL
Internal Regulator Output for IC Supply. Bypass VL to SGND with a 1µF/6.3V ceramic capacitor placed as
close to the IC as possible. VVL regulates to 5.5V with VBSOUT ≥ 5.5V.
15
CT
RESET Timeout Programming Input. Connect a capacitor from CT to SGND to set the RESET timeout
period. See the CT Capacitor Selection section.
16
RESET
RESET Output. RESET is an open-drain output that goes high impedance when VOUT exceeds 92% of the
output voltage threshold after a programmed time delay. RESET pulls low immediately once VOUT drops
below 90% of the regulated LDO output voltage.
—
EP
Exposed Paddle. Connect to the signal ground plane (SGND). Connect to a large-signal ground plane for
increased thermal performance.
Inductor Connection to the Drain of the Internal Power MOSFET. Connect LX to the switched side of the
inductor. Connect pins 10 and 11 together as close to the device as possible. For the MAX5093, also
connect LX to the anode of the external Schottky diode.
_______________________________________________________________________________________
9
MAX5092/MAX5093
Pin Description
4V to 72V Input LDOs with Boost Preregulator
MAX5092/MAX5093
Functional Diagrams
IN
1µs
ONE-SHOT
MAX5092_
OUT
VL
VL
INTERNAL
LDO
LX
IN
LX
BSOUT
S
Q
R
Q
DRIVER
CURRENT-LIMITING
COMPARATOR
R1
RS
OUT
BSFB
VPK
2.25µs
ONE-SHOT
MUX
IN
R2
VREF
LDO
VREF
OUT
ERROR AMPLIFIER
HOLD
OUT_SENSE
CONTROL LOGIC,
THERMAL SHUTDOWN,
AND OVERCURRENT
PROTECTION
EN
R3
R4
VL
MUX
SET
CT
COMPARATOR
2µA
CT
DELAY
COMPARATOR
0.92 x VREF
SGND
PGND_LDO
PGND_BST
P
Figure 1. MAX5092_ Functional Diagram
10
______________________________________________________________________________________
RESET
4V to 72V Input LDOs with Boost Preregulator
IN
1µs
ONE-SHOT
MAX5093_
OUT
VL
VL
INTERNAL
LDO
LX
IN
LX
BSOUT
S
Q
R
Q
DRIVER
CURRENT-LIMITING
COMPARATOR
R1
RS
OUT
BSFB
VPK
2.25µs
ONE-SHOT
MUX
IN
R2
VREF
LDO
VREF
OUT
ERROR AMPLIFIER
HOLD
OUT_SENSE
CONTROL LOGIC,
THERMAL SHUTDOWN,
AND OVERCURRENT
PROTECTION
EN
R3
R4
VL
MUX
SET
CT
COMPARATOR
2µA
CT
DELAY
COMPARATOR
RESET
0.92 x VREF
SGND
PGND_LDO
PGND_BST
P
Figure 2. MAX5093_ Functional Diagram
______________________________________________________________________________________
11
MAX5092/MAX5093
Functional Diagrams (continued)
MAX5092/MAX5093
4V to 72V Input LDOs with Boost Preregulator
Detailed Description
The MAX5092A/MAX5092B/MAX5093A/MAX5093B
include a step-up, switch-mode DC-DC converter and a
linear regulator to provide step-up/-down voltage conversion over a wide range of input voltages. This combination of an LDO and a boost converter offers the
advantage of using a single off-the-shelf inductor in
place of the multiple-winding custom magnetics needed
in typical SEPIC or transformer-based flyback topologies. The boost preregulator is completely turned off
during normal automotive operation (V IN = 14V),
reduces quiescent current to 65µA (typ), and makes the
devices suitable for always-on power supplies.
The devices have an internal UVLO threshold of 3.8V
(max, VIN rising) that must be exceeded before the
device is enabled. When VIN is above VUVLO, the internal boost converter starts switching and regulates
VBSOUT to the programmed boost output voltage. The
low quiescent-current LDO steps down VBSOUT to the
programmed LDO output voltage. The boost output is
preset to 7V, and the LDO output is preset to 3.3V
(MAX5092A/MAX5093A) or 5V (MAX5092B/MAX5093B).
Both output voltages can be adjusted by using external
resistor-dividers.
If VIN rises above 8V (typ), the boost converter is disabled, forcing VBSOUT to follow VIN. If VIN falls below
7.5V (typ), the boost converter starts switching and
regulates VBSOUT to 7V if BSFB is directly connected to
SGND. The boost converter regulates VBSOUT for VIN
down to 3.5V, providing uninterrupted operation during
low cold-crank voltages even if the programmed LDO
output voltage is greater than VIN (but less than 9V).
The boost converter turn-on response time is less than
10µs, making cold-crank input glitches transparent to
the system even at full load.
The boost-converter output is followed by a high PSRR,
low-quiescent-current LDO. The LDO rejects the
switching noise present at BSOUT and provides a
clean, regulated output voltage. The linear regulator
uses an internal p-channel MOSFET pass element.
Additional features include a power-on-reset function
with an externally adjustable timeout, an enable (EN)
input, and a hold (HOLD) regulator control input.
12
Boost Converter
The switch-mode converter uses a minimum off-time,
maximum on-time pulse frequency modulation (PFM)
control scheme. The internal MOSFET turns on whenever VBSOUT falls below the regulation point determined
by VBSFB (see the Setting the Boost Output Voltage
(VBSOUT) section). The MOSFET turns off when the
inductor current reaches the peak current limit (2.5A
typ) or after 2.25µs maximum on-time, whichever
occurs first. The MOSFET is held off for at least 1µs
after the turn-on phase. A new switching cycle initiates
once VBSOUT falls below the threshold. In this control
scheme, switching frequency and output ripple are
functions of load current and input voltage. No frequency compensation is needed in the PFM control scheme.
The output of the boost converter is preset to 7V and is
adjustable by using external resistors. See the Setting
the Boost Output Voltage VBSOUT section. Due to the
integrated blocking diode in the MAX5092_, VBSOUT is
limited to 11V. Use the MAX5093_ for higher boost output voltages (or to reduce the power dissipation in to
the package). The MAX5093_ requires an external
diode for the boost converter. Select the external diode
according to the Schottky Diode Selection (MAX5093_)
section.
Linear Regulator
The MAX5092_/MAX5093_ contain an internal p-channel MOSFET used as the pass transistor for the LDO.
The output of the boost regulator is connected to the
source of the p-MOSFET. The LDO starts up 200µs
after the boost regulator starts up. The LDO supplies
up to 250mA with a typical dropout voltage of 0.9V. The
maximum LDO output current is determined by the
package power-dissipation limit as well as the internal
current limit. The LDO is designed to be a low-quiescent-current type. During normal operation when the
battery voltage is > 9V, the MAX5092_/MAX5093_ consume only 75µA (max) at +85°C and 100µA load.
The output voltage of the LDO is set using the SET
input. Connect SET to SGND to use the factory-preset
output voltage. Connect SET to the center of an external resistor-divider connected from OUT to SGND to
program a different output voltage. See the Setting the
LDO Output Voltage (VOUT) section.
______________________________________________________________________________________
4V to 72V Input LDOs with Boost Preregulator
Enable and Hold Inputs
The MAX5092_/MAX5093_ utilize two logic inputs, EN
(active-high) and HOLD (active low), to implement a
self-holding circuit with no additional components. For
example, an automotive ignition switch drives EN high
and the regulator turns on. If HOLD is then driven low,
the regulator remains on even if EN goes low. As long
as HOLD is forced low and remains low after initial regulator power-up, the regulator remains on. From this
state, release HOLD (an internal current source connects HOLD to OUT), or connect HOLD to OUT to turn
the regulator off. Drive EN low and HOLD high to place
the IC into shutdown mode. Shutdown mode reduces
supply current to 5µA. Figure 3 shows the timing diagram for the enable and hold functions. Table 1 shows
the state of the regulator output with respect to the voltage level at EN and HOLD with reference to Figure 3.
Connect HOLD to OUT or leave unconnected to disable the hold feature and use EN as a standard on/off
control input.
Power-On-Reset Output (RESET)
The MAX5092_/MAX5093_ contain an open-drain output
(RESET) that indicates when the LDO output (VOUT) is
out of regulation. If the output of the LDO falls below 90%
of the nominal output voltage, RESET pulls low after a
short delay. Once the output rises above 92% of the
nominal output voltage, RESET goes high impedance
after the programmed reset timeout period. Connect a
100kΩ pullup resistor from OUT to RESET. See the CT
Capacitor Selection section for details on setting the
RESET timeout period.
HOLD
EN
OUT
ORDER
1
2
4
3
5
6
Figure 3. Enable and Hold Timing Diagram
Table 1. Truth Table for Enable and Hold Timing Diagram
ORDER
EN
HOLD
OUT
COMMENTS
Initial State. EN has a 500nA pulldown to GND. HOLD has an internal current source to OUT.
HOLD follows OUT.
Regulator output is active when EN is pulled high. HOLD is in release state, and it follows
OUT.
HOLD is in release state. OUT follows EN.
1
Low
X
Off
2
High
Released
On
3
Low
Released
Off
4
High
Low
On
HOLD is pulled low externally after OUT turns on. The regulator output is forced on
regardless of the state of EN. A self-holding state.
5
Low
Released
Off
HOLD is released after EN is pulled low. Output turns off.
5
High
X
On
Regulator enabled. Normal turn-on behavior. Regulator follows EN and HOLD follows OUT.
______________________________________________________________________________________
13
MAX5092/MAX5093
Internal Regulator (VL)
An internal regulator (VL) is used to supply all internal
low-voltage blocks. Bypass VL to SGND with a 1µF
ceramic capacitor placed as close to the IC as possible. VVL regulates to 5.5V when VBSOUT is above 5.5V.
V VL tracks the voltage at BSOUT when V BSOUT is
below 5.5V.
4V to 72V Input LDOs with Boost Preregulator
MAX5092/MAX5093
Applications Information
L1
4.7µH
10
INPUT
4V TO 72V
11
LX
1
C1*
47µF
LX
VL
IN
C2*
1µF
14
C6
1µF
U1
MAX5092A
VOUT
BSOUT
R1
100kΩ
16
RESET
PGND_BST
RESET
BSFB
7V
9
12
C3*
1µF
C4*
22µF
13
ON
2
OFF
3
EN
HOLD
OUT
C5
0.22µF
***
µP
SIGNAL
SGND
OUT_SENSE
15
4
CT
PGND_LDO
SET
7
OUTPUT
3.3V AT 250mA**
8
5
6
C7
10µF
VOUT
P
P
*THESE CAPACITORS MUST BE RATED AT THE HIGHEST VIN VOLTAGE.
**OUTPUT CURRENT IS LIMITED BY THE TOTAL POWER-DISSIPATION CAPABILITY OF THE PACKAGE.
***SEE PC BOARD LAYOUT GUIDELINES SECTION.
Figure 4. MAX5092A Typical Application Circuit with Factory Preprogrammed LDO and Boost Output Voltages
14
______________________________________________________________________________________
4V to 72V Input LDOs with Boost Preregulator
L1
4.7µH
10
INPUT
4V TO 72V
11
LX
1
C1*
47µF
LX
VL
IN
C2*
1µF
14
C6
1µF
U1
MAX5093A
VOUT
BSOUT
R1
100kΩ
16
RESET
PGND_BST
RESET
BSFB
9
7V
12
C4*
22µF
C3*
1µF
13
ON
2
OFF
3
EN
HOLD
µP
SIGNAL
SGND
OUT_SENSE
OUT
15
4
CT
C5
0.22µF
***
PGND_LDO
SET
7
OUTPUT
3.3V AT 250mA**
8
5
6
C7
10µF
VOUT
P
P
*THESE CAPACITORS MUST BE RATED AT THE HIGHEST VIN VOLTAGE.
**OUTPUT CURRENT IS LIMITED BY THE TOTAL POWER-DISSIPATION CAPABILITY OF THE PACKAGE.
***SEE PC BOARD LAYOUT GUIDELINES SECTION.
Figure 5. MAX5093A Typical Application Circuit with Factory Preprogrammed Boost and LDO Output Voltages
______________________________________________________________________________________
15
MAX5092/MAX5093
Applications Information (continued)
4V to 72V Input LDOs with Boost Preregulator
MAX5092/MAX5093
Applications Information (continued)
L1
4.7µH
10
INPUT
4V TO 72V
11
LX
1
C1*
47µF
LX
VL
IN
C2*
1µF
14
5.5V
C6
1µF
U1
MAX5092A
VOUT
BSOUT
R3
100kΩ
16
RESET
PGND_BST
OUTPUT
8V (11V MAX)
9
12
C4*
22µF
C3*
1µF
R1
2.74MΩ (3.92MΩ)
RESET
BSFB
13
ON
2
OFF
3
EN
HOLD
OUT
CT
C5
0.22µF
***
µP
SIGNAL
R2
499kΩ
VOUT
SGND
OUT_SENSE
15
4
PGND_LDO
SET
7
OUTPUT
5V** (9V MAX)
8
5
6
C7
10µF
R4
301kΩ (619kΩ)
P
R5
100kΩ
P
*THESE CAPACITORS MUST BE RATED AT THE HIGHEST VIN VOLTAGE.
**OUTPUT CURRENT IS LIMITED BY THE TOTAL OUTPUT POWER AND THE DISSIPATION CAPABILITY OF THE PACKAGE.
***SEE PC BOARD LAYOUT GUIDELINES SECTION.
Figure 6. MAX5092A Typical Application Circuit with User-Programmed LDO and Boost Output Voltages
16
______________________________________________________________________________________
4V to 72V Input LDOs with Boost Preregulator
L1
4.7µH
10
INPUT
4V TO 72V
11
LX
1
C1*
47µF
LX
VL
IN
C2*
1µF
14
C6
1µF
U1
MAX5093A
VOUT
BSOUT
R3
100kΩ
16
RESET
PGND_BST
OUTPUT
9V (12V MAX)
9
12
C4*
22µF
C3*
1µF
R1
3.16MΩ (4.32MΩ)
RESET
BSFB
13
ON
2
OFF
3
EN
HOLD
OUT
CT
C5
0.22µF
***
µP
SIGNAL
R2
499kΩ
VOUT
SGND
OUT_SENSE
15
4
PGND_LDO
SET
7
OUTPUT
5V** (10V MAX)
8
5
C7
10µF
R4
301kΩ (698kΩ)
6
P
R5
100kΩ
*THESE CAPACITORS MUST BE RATED AT THE HIGHEST VIN VOLTAGE.
**OUTPUT CURRENT IS LIMITED BY THE TOTAL OUTPUT POWER AND THE DISSIPATION CAPABILITY OF THE PACKAGE.
***SEE PC BOARD LAYOUT GUIDELINES SECTION.
Figure 7. MAX5093A Typical Application Circuit with User-Programmable Boost Output Voltage and LDO Output Voltage
______________________________________________________________________________________
17
MAX5092/MAX5093
Applications Information (continued)
MAX5092/MAX5093
4V to 72V Input LDOs with Boost Preregulator
Design Guidelines
Input Capacitor (CIN) and
Boost Capacitor (CBSOUT) Selection
The input current waveform of the boost converter is
continuous, and usually does not demand high capacitance at its input. However, the MAX5092_/MAX5093_
boost converter is designed to fully turn on as soon as
the input drops below a certain voltage in order to ride
out cold-crank droops. This operation demands low
input source impedance for proper operation. If the
source (battery) is located far from the IC, high-capacity, low-ESR capacitors are recommended for CIN. The
worst-case peak capacitor current could be as high as
3A. Use a 47µF, 100mΩ low-ESR capacitor placed as
close as possible to the input of the device. Note that
the aluminum electrolytic capacitor ESR increases significantly at cold temperatures. In the cold temperature
case, choose an electrolyte capacitor with ESR lower
than 40mΩ or connect a low-ESR ceramic capacitor
(10µF) in parallel with the electrolytic capacitor.
The boost converter output (BSOUT) is fed to the input
of the internal 250mA LDO. The boost-converter output
current waveform is discontinuous and requires highcapacity, low-ESR capacitors at BSOUT to ensure low
VBSOUT ripple. During the on-time of the internal MOSFET,
the BSOUT capacitor supplies 250mA current to the
LDO input. During the off-time, the inductor dumps current into the output capacitor while supplying the output
load current. The internal 250mA LDO is designed with
high PSRR; however, high-frequency spikes may not be
rejected by the LDO. Thus, high-value, low-ESR electrolytic capacitors are recommended for C BSOUT .
Peak-to-peak VBSOUT ripple depends on the ESR of the
electrolyte capacitor. Use the following equation to calculate the required ESR (ESR BSOUT) of the BSOUT
capacitor:
ESRBSOUT =
18
∆VESRBS
ILIM − IOUT
where ∆VESRBS is 75% of total peak-to-peak ripple at
BSOUT, ILIM is the internal switch current limit (3A max),
and IOUT is the LDO output current. Use a 100mΩ or
lower ESR electrolytic capacitor. Make sure the ESR at
cold temperatures does not cause excessive ripple
voltage. Alternately, use a 10µF ceramic capacitor in
parallel with the electrolyte capacitor.
During the switch on-time, the BSOUT capacitor discharges while supplying IOUT. The ripple caused by
the capacitor discharge (∆VCBS) is estimated by using
the following equation:
I
× 2.7 × 10−6
∆VCBS = OUT
CBSOUT
where IOUT is the LDO output current and CBSOUT is
the BSOUT capacitance.
Inductor Selection
The control scheme of the MAX5092/MAX5093 permits
flexibility in choosing an inductor value. Smaller inductance values typically offer smaller physical size for a
given series resistance, allowing the smallest overall
circuit dimensions. Circuits using larger inductance
may provide higher efficiency and exhibit less ripple,
but also may reduce the maximum output current. This
occurs when the inductance is sufficiently large to prevent the LX current limit (I LIM ) from being reached
before the maximum on-time (tON-MAX) expires.
For maximum output current, choose the inductor value
so that the controller reaches the current limit before
the maximum on-time is reached:
V ×t −
L ≤ IN ON MAX
ILIM
where tON-MAX is typically 2.25µs, and the current limit
(I LIM ) is a maximum of 3A (see the Electrical
Characteristics). Choose an inductor with the maximum
saturation current (ISAT) greater than 3A.
______________________________________________________________________________________
4V to 72V Input LDOs with Boost Preregulator
The MAX5092_/MAX5093_ feature Dual Mode™ operation for the internal boost converter output voltage.
These devices operate in a preset output-voltage mode
or an adjustable output-voltage mode. In preset mode,
internal trimmed feedback resistors set VBSOUT to a
fixed 7V. Select the preset mode by directly connecting
BSFB to SGND (Figures 4 and 5). Ensure a low-impedance path between BSFB and SGND to limit the transient at BSFB to below 100mV. In adjustable mode,
connect BSFB to the center tap of an external resistordivider connected between BSOUT and SGND to program VBSOUT (Figures 6 and 7). Note that the current
drawn by the resistor-divider at BSOUT adds to the quiescent current and the shutdown current of the IC. Use
the resistor-divider only if VBSOUT is required to be significantly different than 7V. Select 499kΩ or lower resistance value for the bottom resistor (R2) of the divider
connected to SGND. The top resistor (R1) value is calculated as:
⎛V
⎞
R1 = R2 × ⎜ BSOUT − 1⎟
V
⎝ BSFB
⎠
where VBSFB is the regulation voltage at BSFB (1.24V
typ) and V BSOUT is the desired output voltage for
BSOUT.
Setting the LDO Output Voltage (VOUT)
The LDO output voltage is also Dual Mode (preset and
adjustable). Preset mode is selected by connecting
SET to SGND (Figures 4 and 5). In preset mode, VOUT
regulates to 3.3V (MAX5092A/MAX5093A) or 5V
(MAX5092B/MAX5093B) by internal trimmed feedback
resistors. Adjustable mode is selected by connecting
SET to the center tap of an external resistor-divider
connected between OUT and SGND (Figures 6 and 7).
Note that the current drawn by the resistor-divider at
OUT adds to the quiescent current of the LDO. Use the
resistor-divider only if VOUT is required to be significantly different than the preset voltage. Select 100kΩ or
lower value for the bottom resistor (R5) of the divider
connected to SGND. The top resistor (R4) value is calculated as:
Schottky Diode Selection (MAX5093_)
The MAX5093_ requires an external diode connected
between LX and BSOUT (Figures 5 and 7). Proper
selection of an external diode can offer a lower forwardvoltage drop and a higher reverse-voltage handling
capability. Since the high switching frequency of the IC
demands a high-speed rectifier, Schottky diodes are
recommended for most applications because of their
fast recovery time and low forward-voltage drop.
Ensure that the diode’s peak current rating is greater
than or equal to the peak current limit of internal boost
converter MOSFET. A diode average forward current
rating of at least 1A is recommended. Additionally, the
diode reverse breakdown voltage must be greater than
the worst-case load-dump-condition voltage.
CT Capacitor Selection
The MAX5092_/MAX5093_ contain an open-drain
power-on-reset output (RESET) that indicates when the
LDO output voltage (VOUT) is out of regulation. When
VOUT rises above 92% of the nominal output voltage,
RESET goes high impedance after a user-programmable time delay. This time duration is programmable by a
capacitor (CCT) from CT to SGND (Figures 4–7). For a
chosen RESET active timeout period (tDELAY), calculate
the required capacitor value as:
CCT =
2 × 10 −6 × tDELAY
1.24
When VOUT drops below 90% of the LDO output regulation voltage, a 5mA pulldown current from CT to SGND
discharges CCT. The time required to discharge CT
determines the delay necessary to pull RESET low. This
delay provides glitch immunity to the RESET function.
The glitch immunity delay is directly proportional to the
CT capacitor and is approximately 70µs for a 0.1µF
capacitor at CT.
⎛V
⎞
R4 = R5 × ⎜ OUT − 1⎟
⎝ VSET ⎠
where VSET is the regulation voltage at SET (1.24V typ)
and VOUT is the desired output voltage for the LDO
output.
Dual Mode is a trademark of Maxim Integrated Products, Inc.
______________________________________________________________________________________
19
MAX5092/MAX5093
Setting the Boost
Output Voltage (VBSOUT)
MAXIMUM POWER DISSIPATION
vs. AMBIENT TEMPERATURE
MAX5092/93 fig08
3.0
MAXIMUM POWER DISSIPATION (W)
MAX5092/MAX5093
4V to 72V Input LDOs with Boost Preregulator
2.5
2.0
1.5
PC Board Layout Guidelines
1.0
0.5
0
-40 -25 -10 5 20 35 50 65 80 95 110 125
AMBIENT TEMPERATURE (°C)
Figure 8. MAX5092/MAX5093 Package Power Dissipation
Maximum Output Current (IOUT_MAX)
The MAX5092_/MAX5093_ high input voltage (+72V
max) provides up to 250mA of current from OUT.
Package power-dissipation limits the amount of output
current available for a given input/output voltage and
ambient temperature. Figure 8 depicts the maximum
power-dissipation curve for the devices. The graph
assumes that the exposed metal pad of the IC package
is soldered to the PC board copper according to the
JEDEC 51 standard (multilayer board). Use Figure 8 to
determine the allowable package dissipation for a
given ambient temperature. Alternately, use the following formula to calculate the allowable package dissipation (PDISS) in watts:
For TA ≤ +70°C:
PDISS = 2.67
For +70°C < TA ≤ +125°C:
PDISS = 2.67 - (0.0333 x (TA - 70))
where +70°C < TA ≤ +125°C and 0.0333W/°C is the
package thermal derating. After determining the allowable package dissipation, calculate the maximum output current (IOUT_MAX) using the following formula:
IOUT _ MAX =
PDISS − PLOSS(BST)
VIN − VOUT
where PDISS is the allowable package power dissipation and PLOSS(BST) is the boost converter power loss.
20
PDISS includes the losses in the boost converter operation and the LDO itself. The boost converter loss
PLOSS(BST), depends on VIN, VBSOUT, and IOUT. See
the Boost Converter Power Loss graphs in the Typical
Operating Characteristics to estimate the losses at a
given VIN and VBSOUT at room temperature. At a higher
ambient temperature of +105°C, PLOSS(BST) increases
by up to 20% due to higher RDS-ON and switching losses of the internal boost converter MOSFET. (Note:
IOUT_MAX must be less than 250mA).
Good PC board (PCB) layout and routing are required
in high-frequency switching power supplies to achieve
proper regulation and stability. It is strongly recommended that the evaluation kit PCB layouts be followed
as closely as possible. Refer to the MAX5092 EV kit for
an example layout. Follow these guidelines for good
PCB layout:
1) For SGND, use a large copper plane under the IC
and solder it to the exposed paddle. To effectively
use this copper area as a heat exchanger between
the PCB and ambient, expose this copper area on
the top and bottom side of the PCB. Do not make a
direct connection from the EP copper plane to pin 3
(SGND) underneath the IC so as to minimize
ground bounce.
2) Isolate the power components and high-current
path from the sensitive analog circuit.
3) Keep the high-current paths short, especially at the
ground terminals. This practice is essential for stable, jitter-free operation.
4) Connect the return terminals of input capacitors
and boost output capacitors to the PGND_BST
power ground plane. Connect the power ground
(PGND_BST) and signal ground (SGND) planes
together at the negative terminal of the input capacitors. Do not connect them anywhere else. Connect
PGND_LDO ground plane to SGND ground plane
at a single point.
5) Ensure that the feedback connections are short and
direct. Ensure a low-impedance path between
BSFB and SGND to limit the transient at BSFB to
100mV.
6) Route high-speed switching nodes away from the
sensitive analog areas. Use the internal PCB layer
for SGND as an EMI shield to keep radiated noise
away from the IC, feedback dividers, and bypass
capacitors.
______________________________________________________________________________________
4V to 72V Input LDOs with Boost Preregulator
INPUT
4V TO 72V
LX
LX
VL
IN
MAX5092B
VOUT
+7V OUTPUT
BSOUT
PGND_BST
RESET
OUTPUT
RESET
BSFB
ENABLE
EN
HOLD
SGND
OUT_SENSE
+5V OUTPUT
VOUT
OUT
*
CT
PGND_LDO
P
SET
P
*SEE PC BOARD LAYOUT GUIDELINES SECTION.
Selector Guide
PART
PRESET LDO
OUTPUT (V)
ADJUSTABLE
LDO OUTPUT
PRESET BSOUT
OUTPUT (V)
ADJUSTABLE BSOUT
OUTPUT
BOOST DIODE
MAX5092AATE+
3.3
Yes
7
Yes
Internal
MAX5092BATE+
5
Yes
7
Yes
Internal
MAX5093AATE+
3.3
Yes
7
Yes
External
MAX5093BATE+
5
Yes
7
Yes
External
Chip Information
PROCESS: BiCMOS
______________________________________________________________________________________
21
MAX5092/MAX5093
Typical Operating Circuit
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
QFN THIN.EPS
MAX5092/MAX5093
4V to 72V Input LDOs with Boost Preregulator
22
______________________________________________________________________________________
4V to 72V Input LDOs with Boost Preregulator
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 23
© 2006 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
MAX5092/MAX5093
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)