Electrical / Environmental Surface Mount Common Mode Chokes Sfor RCoompH t n a li ls • • • • ode ‘LF’ M Operating Temperature Range Ambient Temperature, Maximum Temperature Rise, Maximum Dielectric Withstanding Voltage -40°C to +125°C 85°C 40°C 300Vdc Schematic Specifications Part HM67-B5R0 HM67-B110 HM67-S250 HM67-B510 HM67-S510 HM67-B471 HM67-B102(3) HM67-B222(3) HM67-B472(3) HM67-10510 Notes: Inductance Leakage @100 kHz - 0.1 Vrms (1-4)(1) Typ. 5.0 ±30% 11.0 ±30% 25.0 ±30% 51.0 ±30% 51.0 ±30% 470.0 ±30% 1000.0 +50%, -30% 2200.0 +50%, -30% 4700.0 +50%, -30% 51.0 ±30% 0.08 0.10 1.60 1.90 2.80 0.80 0.16 0.16 0.24 2.40 µH Terminals 1-4, 2-3 1-4, 2-3 1-4, 2-3 1-4, 2-3 1-4, 2-3 1-4, 2-3 1-4, 2-3 1-4, 2-3 1-4, 2-3 1-4, 2-3 Number Common Mode Inductance @100 kHz - 0.1 V (1-4 or 2-3) µH DCR (2) Max. mΩ 7.2 5.8 9.8 7.2 9.4 8.2 9.4 8.2 9.8 403 Rated Current mA 1000 500 500 500 500 500 500 400 200 200 Marking Code A B C D E F G H I 0510 Figure 1 1 1 1 1 1 1 1 1 2 (1) Leakage inductance is measured with pin 2 & 3 shorted. (2) DC resistance is measured at 25°C. (3) Maximum operating temperature is +85°C. Packaging Standard: Embossed Tape & Reel Reel: Diameter: Capacity: Figure 1 & 2 Figure 1 Figure 2 = = = 13” (330.2mm) 400 Units 2000 Units Ordering Information Model Series HM67 Winding Type: B = Bifilar S /10= Sector B 110 LF TR13 TR13 = Tape & 13” Reel (Standard) No code used for tubes Lead-Free Option LF = Lead-Free (No code used for non lead-free part) Inductance Code: First 2 digits are significant. Last digit denotes the number of trailing zeros. For values below 10µH, “R” denotes the decimal point. 2006 EDITION MAGNETIC COMPONENTS SELECTOR GUIDE www.bitechnologies.com We reserve the right to change specifications without prior notice 33 (Inch / mm) Outline Dimensions (Inch/mm) Figure 1 Figure 2 Bottom View Side View .024 0.60 Typ. .138 3.50 Max. .155 3.9 Max. .197 5.00 Max. Seating Plane .004/0.10MAX Side View Top View Top View .37 Max. 9.4 Marking Location .10±.004 2.5±0.1 1 4 2 3 .140 Max. 3.55 .236 Max. 6.0 .138 3.5 Max. Marking (Refer to Specifications Table) Recommended Solder Pad Layout Recommended Solder Pad Layout .090 .098 2.3 2.5 .047 1.2 .067 1.7 .177 34 .087 4.5 2.2 .40 10.2 .232 5.9 MAGNETIC COMPONENTS SELECTOR GUIDE 2006 EDITION We reserve the right to change specifications without prior notice. www.bitechnologies.com Electrical Characteristies @ 25°C (A) Attenuation vs. Frequency Graphs HM67-B5R0 HM67-S250 HM67-B110 HM67-B510 HM67-B110 2006 EDITION MAGNETIC COMPONENTS SELECTOR GUIDE www.bitechnologies.com We reserve the right to change specifications without prior notice 35 Electrical Characteristies @ 25°C (Cont’d) HM67-S510 HM67-B102 HM67-B471 HM67-B222 HM67-B222 HM67-B472 36 MAGNETIC COMPONENTS SELECTOR GUIDE 2006 EDITION We reserve the right to change specifications without prior notice. www.bitechnologies.com Electrical Characteristies @ 25°C (Cont’d) (B) Insertion Loss vs. Frequency Graph HM67-10510 Common Mode Insertion Loss (dB) Common Mode Differential Mode Differential Mode Frequency (MHz) (C) Current Derating Curve I o/p / I Rated HM67-10510 Ambient Temperature (0C) 2006 EDITION MAGNETIC COMPONENTS SELECTOR GUIDE www.bitechnologies.com We reserve the right to change specifications without prior notice 37