SM5006 series Crystal Oscillator Module ICs OVERVIEW The SM5006 series are crystal oscillator module ICs, that incorporate high-frequency, low current consumption oscillator and output buffer circuits. Highly accurate thin-film feedback resistors and high-frequency capacitors are built-in, eliminating the need for external components to make a stable 3rd overtone oscillator. FEATURES ■ ■ ■ ■ ■ ■ Up to 107MHz operation Capacitors CG, CD built-in Inverter amplifier feedback resistor built-in TTL input level 16mA (VDD = 4.5V) drive capability 4mA (VDD = 4.5V) drive capability (5006AH×) ■ ■ ■ ■ ■ Output three-state function 2.7 to 5.5V supply voltage Oscillator frequency output 8-pin SOP (SM5006×××S) Chip form (CF5006×××) SERIES CONFIGURATION 3V operating Version*1 gm ratio SM5006ANAS SM5006ANBS SM5006ANCS SM5006ANDS 0.5 1 2 2 Output load (max) [pF] − − 15 15 Recommended operating frequency range*2 [MHz] − − 22 to 30 30 to 50 SM5006ANES 3 15 50 to 70 SM5006ANFS 4 − − SM5006CNCS 2 15 22 to 30 SM5006CNDS SM5006CNES 2 3 15 15 30 to 40 50 to 70 SM5006BNCS 2 15 22 to 70 SM5006BNES 3 15 22 to 70 SM5006DNCS 2 15 22 to 40 SM5006DNES 3 15 22 to 70 SM5006AKAS SM5006AKBS SM5006AKCS SM5006AKDS SM5006CKDS SM5006BKCS SM5006DKCS SM5006AHAS SM5006AHBS SM5006AHCS SM5006AHDS 0.5 1 2 2 2 2 2 0.5 1 2 2 − − − − − − − − − − − − − − − − − − − − − − Built-in capacitance 5V operating Output load (max) [pF] 50 50 50 50 30 (15)*4 30 (15)*4 15 50 15 15 15 50 30 (15)*4 15 50 15 50 15 15 15 15 15 15 15 15 15 15 15 Rf [kΩ] Input level Output duty level 16 16 16 16 8.2 5.6 4.9 2.6 TTL TTL TTL TTL CMOS CMOS CMOS CMOS 8 16 2.6 TTL CMOS 6/6 8 16 2.6 TTL CMOS Recommended operating frequency range*2 [MHz] 22 to 30 30 to 40 40 to 60 50 to 70 Output waveform*3 tr /tf [ns] CG [pF] CD [pF] 8/8 8/8 7/7 7/7 8 8 8 8 70 to 100 6/6 80 to 107 40 to 60 40 to 50 50 to 70 70 to 100 22 to 100 22 to 70 8/8 8 16 4.9 TTL CMOS 8/8 7/7 8 8 16 16 2.6 2.6 TTL TTL CMOS CMOS 7/7 8 16 No TTL CMOS 70 to 107 6/6 8 16 No TTL CMOS 8/8 8 16 No TTL CMOS 7/7 8 16 No TTL CMOS 4/4 4/4 4/4 4/4 4/4 4/4 4/4 7/7 7/7 7/7 7/7 8 8 8 8 8 8 8 8 8 8 8 16 16 16 16 16 16 16 16 16 16 16 8.2 5.6 4.9 2.6 2.6 No No 8.2 5.6 4.9 2.6 TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL TTL CMOS CMOS CMOS CMOS 22 to 70 22 to 50 22 to 100 22 to 70 22 to 30 30 to 40 40 to 60 50 to 70 50 to 70 22 to 70 22 to 70 22 to 30 30 to 40 40 to 60 50 to 70 *1. Chip form devices have designation CF5006×××. *2. The recommended operating frequency is a yardstick value derived from the crystal used for NPC characteristics authentication. However, the oscillator frequency band is not guaranteed. Specifically, the characteristics can vary greatly due to crystal characteristics and mounting conditions, so the oscillation characteristics of components must be carefully evaluated. *3. 5006×N×: CL = 50pF, CMOS load, 5006×K×: CL = 15pF, 10TTL load, 5006AH×: CL = 15pF, CMOS load *4. SOP package only SEIKO NPC CORPORATION —1 SM5006 series ORDERING INFORMATION Device Package SM5006×××S 8-pin SOP CF5006×××–1 Chip form PACKAGE DIMENSIONS (Unit: mm) • 8-pin SOP 0.4 0.2 6.2 0.3 4.4 0.2 0.15 + 0.1 − 0.05 0.695typ 1.5 0.1 0.05 0.05 5.2 0.3 1.27 0 to 10 0.10 0.4 0.1 0.12 M SEIKO NPC CORPORATION —2 SM5006 series PAD LAYOUT PINOUT (Unit: µm) (Top view) VDD Q (920,1310) HA5006 Y (0,0) INHN XT XTN VSS INHN 1 8 VDD XT 2 7 NC XTN 3 6 NC VSS 4 5 Q X Chip size: 0.92 × 1.31mm Chip thickness: 300 ± 30µm Chip base: VDD level PIN DESCRIPTION and PAD DIMENSIONS Pad dimensions [µm] Number Name I/O Description 1 INHN I Output state control input. High impedance when LOW. Pull-up resistor built in X Y 195 212 2 XT I Amplifier input. 3 XTN O Amplifier output. 4 VSS – Ground 766 212 5 Q O Output. Output frequency (fO) 765 1152 6 NC – No connection – – 7 NC – No connection – – 8 VDD – Supply voltage 162 1152 Crystal oscillator connection pins. Crystal oscillator connected between XT and XTN 385 212 575 212 BLOCK DIAGRAM VDD VSS XTN RG CG XT RD Rf CD Q INHN SEIKO NPC CORPORATION —3 SM5006 series SPECIFICATIONS Absolute Maximum Ratings VSS = 0V Parameter Symbol Condition Rating Unit Supply voltage range VDD −0.5 to 7.0 V Input voltage range VIN −0.5 to VDD + 0.5 V Output voltage range VOUT −0.5 to VDD + 0.5 V Operating temperature range Topr −40 to 85 °C Storage temperature range Tstg Output current Power dissipation IOUT PD Chip form −65 to 150 8-pin SOP −55 to 125 5006×N×, ×K× 25 5006AH× 10 8-pin SOP 500 °C mA mW SEIKO NPC CORPORATION —4 SM5006 series Recommended Operating Conditions SM5006 series (package form) VSS = 0V Rating Parameter Symbol Series typ max f ≤ 50MHz, CL = 50pF 4.5 – 5.5 f ≤ 70MHz, CL = 15pF 4.5 – 5.5 f ≤ 40MHz, CL = 15pF 2.7 – 3.6 f ≤ 70MHz, CL = 50pF 4.5 – 5.5 f ≤ 100MHz, CL = 15pF 4.5 – 5.5 f ≤ 50MHz, CL = 15pF 2.7 – 3.6 f ≤ 70MHz, CL = 15pF 3.0 – 3.6 f ≤ 100MHz, CL = 15pF 4.5 – 5.5 f ≤ 107MHz, CL = 15pF 4.5 – 5.5 f ≤ 50MHz, CL = 15pF 2.7 – 3.6 f ≤ 70MHz, CL = 15pF 3.0 – 3.6 AKA, AKB, AKC, CKD, DKC f ≤ 70MHz, CL = 15pF 4.5 – 5.5 V AKD, BKC f ≤ 70MHz, CL = 15pF 4.5 – 5.5 V AHA, AHB, AHC, AHD f ≤ 70MHz, CL = 15pF 4.5 – 5.5 V VSS – VDD V f ≤ 50MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85 f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 0 – + 70 f ≤ 40MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 − 10 – + 70 f ≤ 50MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 80 f ≤ 70MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80 f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85 f ≤ 100MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 0 – + 70 f ≤ 50MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 − 20 – + 80 f ≤ 70MHz, CL = 15pF, 3.0 ≤ VDD ≤ 3.6 − 20 – + 80 f ≤ 70MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80 f ≤ 100MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85 f ≤ 107MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80 f ≤ 50MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 − 20 – + 80 f ≤ 70MHz, CL = 15pF, 3.0 ≤ VDD ≤ 3.6 − 20 – + 80 f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85 f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 0 – + 70 f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85 f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80 f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85 f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 15 – + 75 ANC, AND, BNC, CNE, DNE VDD ANE, ANF, BNE Input voltage VIN All series ANA, ANB, CNC, CND, DNC ANC, AND, BNC, CNE, DNE Operating temperature Unit min ANA, ANB, CNC, CND, DNC Supply voltage Condition TOPR ANE, ANF, BNE AKA, AKB, AKC, CKD, DKC AKD, BKC AHA, AHB, AHC, AHD V V V °C °C °C °C °C °C SEIKO NPC CORPORATION —5 SM5006 series CF5006 series (chip form) VSS = 0V Rating Parameter Symbol Series typ max f ≤ 50MHz, CL = 50pF 4.5 – 5.5 f ≤ 70MHz, CL = 15pF 4.5 – 5.5 f ≤ 40MHz, CL = 15pF 2.7 – 3.6 f ≤ 70MHz, CL = 50pF 4.5 – 5.5 f ≤ 100MHz, CL = 15pF 4.5 – 5.5 f ≤ 50MHz, CL = 15pF 2.7 – 3.6 f ≤ 70MHz, CL = 15pF 3.0 – 3.6 f ≤ 70MHz, CL = 50pF 4.5 – 5.5 f ≤ 107MHz, CL = 30pF 4.5 – 5.5 f ≤ 50MHz, CL = 15pF 2.7 – 3.6 f ≤ 70MHz, CL = 15pF 3.0 – 3.6 AKA, AKB, AKC, CKD, DKC f ≤ 70MHz, CL = 15pF 4.5 – 5.5 V AKD, BKC f ≤ 70MHz, CL = 15pF 4.5 – 5.5 V AHA, AHB, AHC, AHD f ≤ 70MHz, CL = 15pF 4.5 – 5.5 V VSS – VDD V f ≤ 50MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85 f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 15 – + 75 f ≤ 40MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 − 10 – + 70 f ≤ 70MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85 f ≤ 100MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80 f ≤ 50MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 − 20 – + 80 f ≤ 70MHz, CL = 15pF, 3.0 ≤ VDD ≤ 3.6 − 20 – + 80 f ≤ 70MHz, CL = 50pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85 f ≤ 100MHz, CL = 30pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85 f ≤ 107MHz, CL = 30pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80 f ≤ 50MHz, CL = 15pF, 2.7 ≤ VDD ≤ 3.6 − 20 – + 80 f ≤ 70MHz, CL = 15pF, 3.0 ≤ VDD ≤ 3.6 − 20 – + 80 f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85 f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 15 – + 75 f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85 f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80 f ≤ 50MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 40 – + 85 f ≤ 70MHz, CL = 15pF, 4.5 ≤ VDD ≤ 5.5 − 20 – + 80 ANC, AND, BNC, CNE, DNE VDD ANE, ANF, BNE Input voltage VIN All series ANA, ANB, CNC, CND, DNC ANC, AND, BNC, CNE, DNE Operating temperature TOPR Unit min ANA, ANB, CNC, CND, DNC Supply voltage Condition ANE, ANF, BNE AKA, AKB, AKC, CKD, DKC AKD, BKC AHA, AHB, AHC, AHD V V V °C °C °C °C °C °C SEIKO NPC CORPORATION —6 SM5006 series Electrical Characteristics 5006×N series 3V operation: VDD = 2.7 to 3.6 V, VSS = 0 V, Ta = −20 to 80 °C unless otherwise noted. Rating Parameter Symbol Condition Unit min typ max HIGH-level output voltage VOH Q: Measurement cct 1, VDD = 2.7V, IOH = 8mA 2.2 2.4 – V LOW-level output voltage VOL Q: Measurement cct 2, VDD = 2.7V, IOL = 8mA – 0.3 0.4 V VOH = VDD – – 10 VOL = VSS – – 10 IZ Q: Measurement cct 2, INHN = LOW, VDD = 5.5V HIGH-level input voltage VIH INHN 2.0 – – V LOW-level input voltage VIL INHN – – 0.5 V Output leakage current Current consumption INHN pull-up resistance Feedback resistance Built-in resistance Built-in capacitance IDD RUP Rf INHN = open, Measurement cct 3, load cct 1, VDD = 3.0 to 3.6V, CL = 15pF f = 30MHz SM5006ANCS CF5006ANC SM5006BNCS CF5006BNC – 8 16 f = 30MHz, Ta = –10 to 70°C SM5006CNCS CF5006CNC – 8 16 f = 50MHz SM5006ANDS CF5006AND – 13 26 f = 70MHz SM5006BNES CF5006BNE SM5006CNES CF5006CNE SM5006DNES CF5006DNE – 15 30 f = 40MHz, Ta = –10 to 70°C SM5006CNDS CF5006CND SM5006DNCS CF5006DNC – 11 22 f = 70MHz SM5006ANES CF5006ANE SM5006ANFS CF5006ANF – 20 40 50 – 150 SM5006ANAS, CF5006ANA 6.97 8.2 9.43 SM5006ANBS, CF5006ANB 4.76 5.6 6.44 SM5006ANCS, CF5006ANC SM5006CNCS, CF5006CNC 4.16 4.9 5.64 SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006CNDS, CF5006CND SM5006CNES, CF5006CNE 2.21 2.6 2.99 Measurement cct 4 Measurement cct 5 µA mA kΩ kΩ RG Design value, determined by the Rf value 17 20 23 RD Design value, determined by the Rf value 17 20 23 CG Design value. A monitor pattern on a wafer is tested. 7.44 8 8.56 CD Design value. A monitor pattern on a wafer is tested. 14.88 16 17.12 Ω pF SEIKO NPC CORPORATION —7 SM5006 series 5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Parameter Symbol Rating Condition min typ max Unit HIGH-level output voltage VOH Q: Measurement cct 1, VDD = 4.5V, IOH = 16mA 4.0 4.2 – V LOW-level output voltage VOL Q: Measurement cct 2, VDD = 4.5V, IOL = 16mA – 0.3 0.4 V VOH = VDD – – 10 VOL = VSS – – 10 Output leakage current IZ Q: Measurement cct 2, INHN = LOW, VDD = 5.5V HIGH-level input voltage VIH INHN 2.0 – – V LOW-level input voltage VIL INHN – – 0.8 V INHN = open, Measurement cct 3, load cct 1, VDD = 4.5 to 5.5V, CL = 50pF Current consumption IDD INHN = open, Measurement cct 3, load cct 1, VDD = 4.5 to 5.5V INHN pull-up resistance Feedback resistance Built-in resistance Built-in capacitance RUP Rf f = 30MHz SM5006ANAS CF5006ANA – 18 35 f = 40MHz SM5006ANBS CF5006ANB – 20 40 f = 60MHz CF5006ANC – 30 60 f = 60MHz, Ta = –20 to 80°C SM5006ANCS – 30 50 f = 70MHz CF5006AND CF5006BNC – 40 80 f = 70MHz, Ta = –20 to 80°C SM5006ANDS SM5006BNCS – 40 70 f = 60MHz, CL = 15pF, Ta = –15 to 75°C CF5006CNC – 28 50 f = 60MHz, CL = 15pF, Ta = 0 to 70°C SM5006CNCS – 28 50 f = 70MHz, CL = 15pF, Ta = –15 to 75°C CF5006CND CF5006DNC – 35 65 f = 70MHz, CL = 15pF, Ta = 0 to 70°C SM5006CNDS SM5006DNCS – 35 65 f = 100MHz, CL = 15pF, Ta = –20 to 80°C CF5006CNE CF5006DNE – 45 80 f = 100MHz, CL = 15pF, Ta = 0 to 70°C SM5006CNES SM5006DNES – 45 80 f = 100MHz, CL = 30pF CF5006ANE – 50 100 f = 100MHz, CL = 15pF SM5006ANES – 45 90 f = 107MHz, CL = 30pF, Ta = –20 to 80 °C CF5006ANF CF5006BNE – 60 100 f = 107MHz, CL = 15pF, Ta = –20 to 80°C SM5006ANFS SM5006BNES – 50 90 50 – 150 SM5006ANAS, CF5006ANA 6.97 8.2 9.43 SM5006ANBS, CF5006ANB 4.76 5.6 6.44 SM5006ANCS, CF5006ANC SM5006CNCS, CF5006CNC 4.16 4.9 5.64 SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006CNDS, CF5006CND SM5006CNES, CF5006CNE 2.21 2.6 2.99 Measurement cct 4 Measurement cct 5 µA mA kΩ kΩ RG Design value, determined by the Rf value 17 20 23 RD Design value, determined by the Rf value 17 20 23 CG Design value. A monitor pattern on a wafer is tested. 7.44 8 8.56 CD Design value. A monitor pattern on a wafer is tested. 14.88 16 17.12 Ω pF SEIKO NPC CORPORATION —8 SM5006 series 5006×K series VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter HIGH-level output voltage LOW-level output voltage Symbol VOH VOL Condition Q: Measurement cct 1, VDD = 4.5V, IOH = 16mA Unit min typ max SM5006AKAS, CF5006AKA SM5006AKBS, CF5006AKB SM5006AKCS, CF5006AKC SM5006CKDS, CF5006CKD SM5006DKCS, CF5006DKC 3.9 4.2 – SM5006AKDS, CF5006AKD SM5006BKCS, CF5006BKC 4.0 4.2 – – 0.3 0.4 VOH = VDD – – 10 VOL = VSS – – 10 Q: Measurement cct 2, VDD = 4.5V, IOL = 16mA V V IZ Q: Measurement cct 2, INHN = LOW, VDD = 5.5V HIGH-level input voltage VIH INHN 2.0 – – V LOW-level input voltage VIL INHN – – 0.8 V Output leakage current Current consumption INHN pull-up resistance Feedback resistance Built-in resistance Built-in capacitance IDD RUP Rf INHN = open, Measurement cct 3, load cct 1, VDD = 4.5 to 5.5V, CL = 15pF f = 30MHz SM5006AKAS CF5006AKA – 16 32 f = 40MHz SM5006AKBS CF5006AKB – 18 36 f = 60MHz, Ta = –15 to 75°C CF5006AKC CF5006DKC – 25 50 f = 60MHz, Ta = 0 to 70°C SM5006AKCS SM5006DKCS – 25 50 f = 70MHz, Ta = –20 to 80°C CF5006AKD CF5006BKC – 35 70 f = 70MHz, Ta = –15 to 75°C CF5006CKD – 35 70 f = 70MHz, Ta = 0 to 70°C SM5006AKDS SM5006BKCS SM5006CKDS – 35 70 50 – 150 SM5006AKAS, CF5006AKA 6.97 8.2 9.43 SM5006AKBS, CF5006AKB 4.76 5.6 6.44 SM5006AKCS, CF5006AKC 4.16 4.9 5.64 SM5006AKDS, CF5006AKD SM5006CKDS, CF5006CKD 2.21 2.6 2.99 Measurement cct 4 Measurement cct 5 µA RG Design value, determined by the Rf value 17 20 23 RD Design value, determined by the Rf value 17 20 23 CG Design value. A monitor pattern on a wafer is tested. 7.44 8 8.56 CD Design value. A monitor pattern on a wafer is tested. 14.88 16 17.12 mA kΩ kΩ Ω pF SEIKO NPC CORPORATION —9 SM5006 series 5006AH series VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Rating Parameter Symbol Condition Unit min typ max HIGH-level output voltage VOH Q: Measurement cct 1, VDD = 4.5V, IOH = 4mA 3.9 4.2 – V LOW-level output voltage VOL Q: Measurement cct 2, VDD = 4.5V, IOL = 4mA – 0.3 0.5 V VOH = VDD – – 10 VOL = VSS – – 10 IZ Q: Measurement cct 2, INHN = LOW, VDD = 5.5V HIGH-level input voltage VIH INHN 2.0 – – V LOW-level input voltage VIL INHN – – 0.8 V Output leakage current Current consumption INHN pull-up resistance Feedback resistance Built-in resistance Built-in capacitance IDD RUP Rf INHN = open, Measurement cct 3, load cct 1, VDD = 4.5 to 5.5V, CL = 15pF µA f = 30MHz SM5006AHAS CF5006AHA – 15 30 f = 40MHz SM5006AHBS CF5006AHB – 18 36 f = 60MHz, Ta = –20 to 80°C CF5006AHC – 25 50 f = 60MHz, Ta = –15 to 75°C SM5006AHCS – 25 50 f = 70MHz, Ta = –20 to 80°C CF5006AHD – 32 65 f = 70MHz, Ta = –15 to 75°C SM5006AHDS – 32 65 50 – 150 SM5006AHAS, CF5006AHA 6.97 8.2 9.43 SM5006AHBS, CF5006AHB 4.76 5.6 6.44 SM5006AHCS, CF5006AHC 4.16 4.9 5.64 SM5006AHDS, CF5006AHD 2.21 2.6 2.99 mA Measurement cct 4 Measurement cct 5 kΩ kΩ RG Design value, determined by the Rf value 17 20 23 RD Design value, determined by the Rf value 17 20 23 CG Design value. A monitor pattern on a wafer is tested. 7.44 8 8.56 CD Design value. A monitor pattern on a wafer is tested. 14.88 16 17.12 Ω pF SEIKO NPC CORPORATION —10 SM5006 series Switching Characteristics 5006×N series 3V operation: VDD = 2.7 to 3.6V, VSS = 0V, Ta = −20 to 80°C unless otherwise noted. Parameter Symbol Condition min typ max – 3.5 7.0 Unit Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 15pF, Ta = –10 to 70°C SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC tr2 Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 15pF SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNCS, CF5006BNC SM5006BNES, CF5006BNE SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE – 3.5 7.0 tf1 Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 15pF, Ta = –10 to 70°C SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC – 3.5 7.0 Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 15pF SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNCS, CF5006BNC SM5006BNES, CF5006BNE SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE – 3.5 7.0 Measurement cct 3, load cct 1, Ta = 25°C, VDD = 3.3V, CL = 15pF, f = 30MHz SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006ANCS, CF5006ANC SM5006CNCS, CF5006CNC 40 – 60 Measurement cct 3, load cct 1, Ta = 25°C, VDD = 3.3V, CL = 15pF, f = 40MHz SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC 40 – 60 Measurement cct 3, load cct 1, Ta = 25°C, VDD = 3.3V, CL = 15pF, f = 50MHz SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC 40 – 60 Measurement cct 3, load cct 1, Ta = 25°C, VDD = 3.3V, CL = 15pF, f = 70MHz SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNES, CF5006BNE SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE 40 – 60 – – 100 ns – – 100 ns tr1 Output rise time Output fall time tf2 Output duty cycle*1 Rating Duty Output disable delay time tPLZ Output enable delay time tPZL ns ns % Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF *1. The duty cycle characteristic is checked the sample chips of each production lot. SEIKO NPC CORPORATION —11 SM5006 series 5V operation: VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Parameter Symbol tr1 tr2 Output rise time tr3 tf1 tf2 Output fall time tf3 Condition Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 15pF Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 30pF Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 50pF Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 15pF Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 30pF Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 50pF Rating min typ max SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC – 2.0 4.0 SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE – 1.5 3.0 CF5006ANE CF5006ANF CF5006BNE – 2.0 4.0 SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC – 4.0 8.0 SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE – 3.5 7.0 SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNES, CF5006BNE – 3.0 6.0 SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC – 2.0 4.0 SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE – 1.5 3.0 CF5006ANE CF5006ANF CF5006BNE – 2.0 4.0 SM5006ANAS, CF5006ANA SM5006ANBS, CF5006ANB SM5006CNCS, CF5006CNC SM5006CNDS, CF5006CND SM5006DNCS, CF5006DNC – 4.0 8.0 SM5006ANCS, CF5006ANC SM5006ANDS, CF5006AND SM5006BNCS, CF5006BNC SM5006CNES, CF5006CNE SM5006DNES, CF5006DNE – 3.5 7.0 SM5006ANES, CF5006ANE SM5006ANFS, CF5006ANF SM5006BNES, CF5006BNE – 3.0 6.0 Unit ns ns SEIKO NPC CORPORATION —12 SM5006 series Parameter Output duty cycle*1 Symbol Duty Output disable delay time tPLZ Output enable delay time tPZL Rating Condition Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5.0V min typ max Unit f = 30MHz, CL = 50pF SM5006ANAS CF5006ANA 45 – 55 f = 40MHz, CL = 50pF SM5006ANBS CF5006ANB 45 – 55 f = 60MHz, CL = 50pF SM5006ANCS CF5006ANC 45 – 55 f = 70MHz, CL = 50pF SM5006ANDS CF5006AND SM5006BNCS CF5006BNC 45 – 55 f = 100MHz, CL = 30pF CF5006ANE 45 – 55 f = 100MHz, CL = 15pF SM5006ANES 45 – 55 f = 107MHz, CL = 30pF CF5006ANF CF5006BNE 45 – 55 f = 107MHz, CL = 15pF SM5006ANFS SM5006BNES 45 – 55 f = 50MHz, CL = 50pF SM5006CNCS CF5006CNC SM5006DNCS CF5006DNC 45 – 55 f = 100MHz, CL = 15pF SM5006CNES CF5006CNE SM5006DNES CF5006DNE 45 – 55 f = 60MHz, CL = 15pF SM5006CNCS CF5006CNC 40 – 60 f = 70MHz, CL = 15pF SM5006CNDS CF5006CND SM5006DNCS CF5006DNC 40 – 60 – – 100 ns – – 100 ns Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF % *1. The duty cycle characteristic is checked the sample chips of each production lot. SEIKO NPC CORPORATION —13 SM5006 series 5006×K series VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Parameter Symbol Rating Condition min typ max Unit Output rise time tr Measurement cct 3, load cct 1, 0.4V to 2.4V, VDD = 4.5 to 5.5V CL = 15pF – 2 4 CL = 50pF – – 7 Output fall time tf Measurement cct 3, load cct 1, 2.4V to 0.4V, VDD = 4.5 to 5.5V CL = 15pF – 2 4 CL = 50pF – – 7 f = 30MHz SM5006AKAS CF5006AKA 45 – 55 f = 40MHz SM5006AKBS CF5006AKB 45 – 55 f = 60MHz SM5006AKCS CF5006AKC 40 – 60 f = 70MHz SM5006AKDS CF5006AKD SM5006BKCS CF5006BKC 45 – 55 f = 50MHz SM5006DKCS CF5006DKC 45 – 55 f = 70MHz SM5006CKDS CF5006CKD SM5006DKCS CF5006DKC 40 – 60 – – 100 ns – – 100 ns Output duty cycle*1 Duty Output disable delay time tPLZ Output enable delay time tPZL Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5.0V, CL = 15pF Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF ns ns % *1. The duty cycle characteristic is checked the sample chips of each production lot. 5006AH series VDD = 4.5 to 5.5V, VSS = 0V, Ta = −40 to 85°C unless otherwise noted. Parameter Output rise time Output fall time Output duty cycle*1 Symbol tr1 tr2 tf1 tf2 Duty Output disable delay time tPLZ Output enable delay time tPZL Rating Condition min typ max Unit Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD CL = 15pF – 5.0 7.0 CL = 50pF – 13 21 Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD CL = 15pF – 5.0 7.0 CL = 50pF – 13 21 f = 30MHz SM5006AHAS CF5006AHA 45 – 55 f = 40MHz SM5006AHBS CF5006AHB 45 – 55 f = 50MHz SM5006AHCS CF5006AHC 45 – 55 f = 60MHz, Ta = –20 to 80°C CF5006AHC 40 – 60 f = 60MHz, Ta = –15 to 75°C SM5006AHCS 40 – 60 f = 70MHz, Ta = –20 to 80°C CF5006AHD 40 – 60 f = 70MHz, Ta = –15 to 75°C SM5006AHDS 40 – 60 – – 100 ns – – 100 ns Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5.0V, CL = 15pF Measurement cct 3, load cct 1, Ta = 25°C, VDD = 5V, CL ≤ 15pF ns ns % *1. The duty cycle characteristic is checked the sample chips of each production lot. SEIKO NPC CORPORATION —14 SM5006 series Current consumption and Output waveform with NPC’s standard crystal Cb L Ca R f [MHz] R [Ω] L [mH] Ca [fF] Cb [pF] 30 18.62 16.24 1.733 5.337 40 20.53 11.34 1.396 3.989 50 22.17 7.40 1.370 4.105 70 25.42 4.18 1.254 5.170 100 16.60 3.56 0.726 5.394 107 35.83 2.98 0.732 2.265 FUNCTIONAL DESCRIPTION Standby Function When INHN goes LOW, the oscillator output on Q goes high impedance. INHN Q Oscillator HIGH (or open) fO output frequency Normal operation LOW High impedance Normal operation SEIKO NPC CORPORATION —15 SM5006 series MEASUREMENT CIRCUITS Measurement cct 1 Measurement cct 4 5.0V VDD C1 Signal Generator XT VDD Q R2 Rfo R1 XTN RUP = VDD IPR VSS INHN VSS VOH Q out monitor VIH A 0V IPR 3.5VP−P , 10MHz sine wave input signal (5V operation) 2.0VP−P , 10MHz sine wave input signal (3V operation) C1 : 0.001µF R1 : 50Ω R2 : 250Ω (5006×N×/5V operation) 275Ω (5006×N×/3V operation) 245Ω (5006AKA, AKB, AKC, CKD, DKC) 250Ω (5006AKD, BKC) 975Ω (5006AH×) Rfo : 2.7kΩ (5006B××, D××) Measurement cct 2 Measurement cct 5 IOL, IZ VDD IZ VDD XT A Q XT Rf = XTN INHN VSS V VOL VDD IRf VSS A IRf Measurement cct 3 IDD IST A XT Rfo VDD X'tal Q XTN INHN VSS Rfo : 2.7kΩ (5006B××, D××) SEIKO NPC CORPORATION —16 SM5006 series Load cct 1 Load cct 2 Q output 400Ω CL Q output (Including probe capacitance) CL (Including probe capacitance) Switching Time Measurement Waveform Output duty level (CMOS) 0.9VDD Q output 0.9VDD 0.1VDD 0.1VDD DUTY measurement voltage (0.5V DD ) TW tr tf Output duty level (TTL) 2.4V DD Q output 2.4V DD 0.4V DD 0.4V DD DUTY measurement voltage (1.4V DD ) TW tr tf Output duty cycle (CMOS) DUTY measurement voltage (0.5V DD) Q output TW T DUTY= TW/ T 100 (%) Output duty cycle (TTL) DUTY measurement voltage (1.4V DD) Q output TW T DUTY= TW/ T 100 (%) SEIKO NPC CORPORATION —17 SM5006 series Output Enable/Disable Delay INHN VIH VIL tPLZ tPZL INHN input waveform tr = tf 10ns Q output SEIKO NPC CORPORATION —18 SM5006 series Please pay your attention to the following points at time of using the products shown in this document. The products shown in this document (hereinafter “Products”) are not intended to be used for the apparatus that exerts harmful influence on human lives due to the defects, failure or malfunction of the Products. Customers are requested to obtain prior written agreement for such use from SEIKO NPC CORPORATION (hereinafter “NPC”). Customers shall be solely responsible for, and indemnify and hold NPC free and harmless from, any and all claims, damages, losses, expenses or lawsuits, due to such use without such agreement. NPC reserves the right to change the specifications of the Products in order to improve the characteristic or reliability thereof. NPC makes no claim or warranty that the contents described in this document dose not infringe any intellectual property right or other similar right owned by third parties. Therefore, NPC shall not be responsible for such problems, even if the use is in accordance with the descriptions provided in this document. Any descriptions including applications, circuits, and the parameters of the Products in this document are for reference to use the Products, and shall not be guaranteed free from defect, inapplicability to the design for the mass-production products without further testing or modification. Customers are requested not to export or re-export, directly or indirectly, the Products to any country or any entity not in compliance with or in violation of the national export administration laws, treaties, orders and regulations. Customers are requested appropriately take steps to obtain required permissions or approvals from appropriate government agencies. SEIKO NPC CORPORATION 15-6, Nihombashi-kabutocho, Chuo-ku, Tokyo 103-0026, Japan Telephone: +81-3-6667-6601 Facsimile: +81-3-6667-6611 http://www.npc.co.jp/ Email: [email protected] NC9713FE 2006.04 SEIKO NPC CORPORATION —19