Series AM3G-NZ 3 Watt | DC-DC Converter FEATURES: • RoHS compliant • Very low No load consumption • Remote On/Off Control • 8 pin SIP package • • • • Operating temperature -40oC to + 85oC Continuous Short circuit protection Wide 2:1 input range High efficiency up to 81% Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Capacitor Load (μF) Efficiency 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 5 9 12 15 5 9 12 15 600 333 250 200 600 333 250 200 1500 1500 1500 1500 1500 1500 1500 1500 2200 1000 820 680 2200 1000 820 680 78 79 80 80 78 79 80 81 AM3G-1205S-NZ AM3G-1209S-NZ AM3G-1212S-NZ AM3G-1215S-NZ AM3G-2405S-NZ AM3G-2409S-NZ AM3G-2412S-NZ AM3G-2415S-NZ Models Dual output Model Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Capacitor Load (μF) Efficiency (%) 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 ±5 ±9 ±12 ±15 ±5 ±9 ±12 ±15 ±300 ±167 ±125 ±100 ±300 ±167 ±125 ±100 1500 1500 1500 1500 1500 1500 1500 1500 ±560 ±470 ±330 ±220 ±560 ±470 ±330 ±220 78 79 80 80 78 79 80 81 Maximum Units AM3G-1205D-NZ AM3G-1209D-NZ AM3G-1212D-NZ AM3G-1215D-NZ AM3G-2405D-NZ AM3G-2409D-NZ AM3G-2412D-NZ AM3G-2415D-NZ Input Specifications Parameters Voltage range Nominal 12 24 Filter Maximum Rating 12 Vin 24 Vin Peak Input Voltage time On/Off Control Typical 9-18 18-36 Capacitor 22 40 100 ON – low or open; OFF - high VDC VDC ms Isolation Specifications Parameters Tested voltage Resistance Capacitance www.aimtec.com F 051e R2.A Conditions Typical 60 sec 1500 > 1000 80 100kHz, 1V Tel: +1 514 620 2722 1 of 3 Maximum Units VDC MOhm pF Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM3G-NZ 3 Watt | DC-DC Converter Output Specifications Parameters Conditions Voltage accuracy Voltage balance Short Circuit protection Line voltage regulation Load voltage regulation Temperature coefficient Ripple & Noise Typical At 20MHz Bandwidth ±3 ±5 Continuous ±0.5 ±1 ±0.03 100 Parameters Conditions Typical Switching frequency Operating temperature Storage temperature No load power consumption Cooling Humidity Case material Weight Dimensions (L x H x W) MTBF 100% load With derating above 71oC Dual Output 25~100% load Auto recovery LL~HL load 10~100% Maximum Units % % % % %/oC mV p-p General Specifications Maximum Units 500 KHz o C o C mW >200 -40 to +85 -50 to +125 100 Free air convection % 95 Non-conductive black plastic (UL94V-0 rated) g 6 22 x 9.5 x 12 mm 0.87 x 0.37 x 0.47 inch >1 000 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC) Non condensing Pin Out Specifications Dimensions Pin Single Dual 1 2 3 5 6 7 8 - V Input + V Input On/Off Control N.C. + V Output - V Output CS - V Input + V Input On/Off Control N.C. + V Output Common - V Output Derating Vout CS www.aimtec.com F 051e R2.A Tel: +1 514 620 2722 2 of 3 CS Capacitor Table 5V 9V 12V 15V 24V 47uF – 100uF 10uF – 47uF Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM3G-NZ 3 Watt | DC-DC Converter Control ON/OFF pin connection example: The voltage could be applied through a limiting resistor and a switching diode. The converter is in a low power mode during high level phase. NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 5. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. www.aimtec.com F 051e R2.A Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only