ss w Embedded Power for Business-Critical Continuity Rev. 7.9.09_145 iVS Series of 11 TM Intelligent VS Power Up to 4920 Watts Font: Minion Bold for VS Minion italic for i ; size for each is the same Created on Mac Color: "i" 100% Blue, 50% Magenta, 0% Yellow, 0% Black "VS" - 100% Black Total Power: Up to 4920 Watts Input Voltage: 85 - 264 Vdc 120 - 300 Vdc # of Outputs: Up to 24 Special Features • Full medical EN60601 approval • Intelligent I2C control • Voltage adjustment on all outputs (manual or I2C) • Configurable input and output OK signals and indicators • Configurable inhibit/enable • Configurable output UP/DOWN sequencing • High power density (12 W/cu-in) • Intelligent fan (speed control/ fault status) • uP controlled PFC input with active Inrush protection • I2C monitor of voltage, current, and temperature • Programmable voltage, current limit, inhibit/enable through I2C • Optional extended hold-up module (SEMI F47 compliance) • Increased power density to 150% • Optional conformal coating • Industrial temp range (-40 ºC to 70 ºC) • Uses standard iMP modules • Field upgradeable firmware • RoHS compliant Safety • • • • UL CSA VDE BABT • CB • CE UL60950/UL2601 CSA22.2 No. 234 Level 5 EN60950/EN60601-1 Compliance to EN 60950/ EN60601 BS 7002 Certificate and report Mark to LVD Electrical Specifications Input Input range: iVS1 & iVS3 90 - 264 Vac 1Ø; 120 - 300 Vdc iVS6 & iVS8 170 - 264 Vac 3Ø iVS8H 480 Vac nominal 3Ø 380 Vac nominal 3Ø derate to 3800 W max. Frequency: 47 - 440 Hz Inrush current: 40 A peak maximum (soft start) Efficiency: Up to 85% @ full case load Power Factor: 0.99 typ. meets EN61000-3-2 Turn-on time: AC on 1.5 sec typical, inhibit/enable 150ms typical Programmable; 50ms internal turn-on delay (Dual Output only) EMI Filter: CISPR 22/EN55022 Level “B” Leakage current: 500 µA max. @ 240 Vac; 47-63 Hz Radiated EMI: CISPR 22/EN55022 Level “B” Holdover storage: 10 ms minimum (independent of input Vac) additional 20mSEC holdover storage with optional HUP module (SEMI F47 compatible) AC OK: 5ms early warning minutes before outputs lose regulation Full cycle > ride thru (50 Hz). Programmable Harmonic distortion: Meets EN61000-3-2 Isolation: Meets EN60950 and EN60601 Global inhibit / enable: TTL, Logic “1” and Logic “0”; configurable Warranty: 3 years w Embedded Power for Business-Critical Continuity Rev. 7.9.09_145 iVS Series of 11 Output Adjustment range:* ± 10% minimum all outputs (manual) (full module adjustment range using I2C) Factory set point accuracy: I2C output program accuracy: Margining: Overall regulation: Ripple: 1% ± 5% ± 4 - 6% nominal analog (single output module only) 0.4% or 20 mV max. (1500 W modules 1% max.) RMS: 0.1% or 10 mV, whichever is greater Pk-Pk: 1.0% or 50 mV, whichever is greater Bandwidth limited to 20 MHz < 2% or 100 mV, with 25% load step To within 1% in < 300 µsec Configurable through I2C (calibration required). Single output module and main output of the dual output module 105-120% of rated output current. Aux output of dual output module 105-140% of rated output current. Special programmable OCP delay on 1500 W module from 100 mSec to 25.5 seconds with shutdown features. Protected for continuous short-circuit. Recovery is automatic upon removal of short (Shutdown mode on 1500 W module). Configurable through I2C Dynamic response: Recovery time: Overcurrent protection:** Short-circuit protection: Overvoltage protection:* Single output module: Dual output module: Triple output module: Thermal protection:* Remote sense: Single wire parallel: 2 - 5.5 V 122 - 134% ; 6 - 60 V 110 - 120% 2 - 6 V 122 - 134% ; 8 - 28 V 110 - 120% No overvoltage protection provided Configurable through I2C All outputs disabled when internal temp exceeds safe operating range. > 5ms warning (AC OK signal) before shutdown Up to 0.5 V total drop (not available on triple output module) Current share to within 2% of total rated current DC OK:* +/-5% of nominal. Configurable through I2C Minimum load: Not required Housekeeping bias voltage: 5 Vdc @1.0 A max. present whenever AC input is applied Module inhibit:* Configured and controlled through I2C Output/Output isolation: > 1 Megohm, 500 V * Can be controlled via I2C ** Controlled via I2C but requires load calibration (except 1500 W module) Environmental Specifications Operating temperature: -40 ° to 70 °C ambient. Derate each output 2.5% per degree from 50 ° to 70 °C. ( -20 °C start up) Storage temperature: -40 °C to 85 °C Electromagnetic susceptibility: Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity: Operating; non-condensing 10% to 95% RH Vibration: IEC68-2-6 to the levels of IEC721-3-2 MTBF demonstrated: > 550,000 hours at full load, 220 Vac and 25 °C ambient conditions Embedded Power for Business-Critical Continuity Output Module Line-up Module Code 1 Rev. 7.9.09_145 iVS Series of 11 3 2 5 4 — Module Type Single Single Single Single Dual Triple Max output power 210 W 360 W 750 W 1500 W 144 W 36 W Max output current 35 A 60 A 150 A 140 A 10 A 2A Output voltages available* Standard voltage increments Remote sense Remote margin V-Program - I2C Control Active Current Share Module Inhibit - I2C Control Module Inhibit - Analog Overvoltage/Overcurrent protection Minimum load required Slots occupied in any iVS case 2-60 V 2-60 V 2-60 V 6-60 V 25 25 25 18 8 - 15*, 24 - 28; 8 - 15*, 8 - 15*; 8 8-15, 8-15, 2-6; 8-15, 8-15, 8-15; 8- 15*, 2 - 6; 2 - 6, 2 - 6; 24 - 28, 24 - 28; 15, 8-15, 18-28; 8-15, 18-28, 2-6 24 - 28, 2 - 6 18 16 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes No Yes No Yes No No No No No Yes No Yes Yes Yes Yes Yes Yes Yes No No No No No No No 1 2 3 4 1 1 * Note: Contact Factory for extended range down to 6 V Output Module Voltage/Current* Single Voltage Voltage Code 2V 2.2 V 3V 3.3 V 5V 5.2 V 5.5 V 6.0 V 8.0 V 10 V 11 V 12 V 14 V 15 V 18 V 20 V 24 V 28 V 30 V 33 V 36 V 42 V 48 V 54 V 60 V A B C D E F G H I J K L M N O P Q R S T U V W X Y Single Output Module Code 1 210 W 750 W 360 W 1500 W Dual Triple 35 A 35 A 35 A 35 A 35 A 35 A 34 A 23 A 20 A 18 A 17 A 17 A 14 A 14 A 11 A 10.5 A 8.5 A 6.7 A 6.5 A 6.2 A 5.8 A 4.2 A 4.0 A 3.7 A 3.5 A 2 3 5 60 A 150 A — 60 A 150 A — 60 A 150 A — 60 A 150 A — 60 A 150 A — 60 A 144 A — 58 A 136 A — 42 A 97.5 A 140 A 36 A 84.4 A 140 A 32 A 75 A 140 A 31 A 68 A 136.3 A 30 A 62.5 A 125 A 21 A 53.5 A 107 A 100 A 20 A 50 A 19 A 41.6 A 83.3 A 18 A 37.5 A 75 A 15 A 30 A 62.5 A 11 A 26.8 A 53.5 A 50 A 11 A 25 A 10.9 A 22.7 A 35.8 A 10 A 20.8 A 35.8 A 7.5 A 16 A 35.7 A 7.5 A 15.6 A 31.2 A 6.0 A 13.9 A 27.7 A 6.0 A 12.5 A 25 A Dual Output*** Triple Output 4 4 - - - 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A* 10 A 10 A 10 A 10 A 9A 8A — — 4A 3A — — — — — — — 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A* 4A 4A 4A 4A 4A 4A — — 2A 2A — — — — — — — — — — — — — — — 1A 1A 1A 1A 1A 1A — — — — — — — — — — — — — — — — — — — 1A 1A 1A 1A 1A 1A 0.5 A 0.5 A 0.5 A 0.5 A — — — — — — — 2A 2A 2A 2A 2A 2A 2A 2A 1A 1A 1A 1A 1A 1A 0.5 A 0.5 A 0.5 A 0.5 A — — — — — — — — — — 10 A 10 A 8A I2C Adjustment Ranges**** 1.8 - 2.2 2.0 - 2.4 2.7 - 3.3 3.0 - 3.6 4.5 - 5.5 4.7 - 5.7 5.0 - 6.1 5.4 - 6.6 7.2 - 8.8 9.0 - 11.0 9.9 - 12.1 10.8 - 13.2 12.6 - 15.4 13.5 - 16.5 16.2 - 19.8 18.0 - 22.0 21.6 - 26.4 25.2 - 30.8 27.0 - 33.0 29.7 - 36.3 32.4 - 39.6 37.8 - 46.2 43.2 - 52.8 48.6 - 59.4 54.0 - 66.0 Contact Factory 144 W 36 W Special* Special* Special* Z Z Z 35 A 35 A 20 A 60 A 60 A 36 A 150 A 150 A 80 A — — 140 A 2.3 - 2.6 3.7 - 4.4 6.7 - 7.1 * Note: Contact Factory for extended range down to 6 V. **Increments of current not shown can be achieved by paralleling modules (add currents of each module selected). *** Total output power on dual model must not exceed 144 W. **** For single output modules only. w Embedded Power for Business-Critical Continuity Ordering Information Rev. 7.9.09_145 iVS Series of 11 Sample below is 3210 W case with 12 V @ 125 A; 24 V @ 8.5 A; 5 V @ 60 A; 12 V @ 10 A and 12 V @ 4 A; with no options. Module/Voltage/Option Codes First - Module Code Second - Voltage Code Third - Option Code Case Size iVS1 - 5L1 - 1Q1 - 2EO - 4LL0 - Case Size (mm) 1-Phase Input 1 = 5” x 5” x 11”; 1500 W - 3210 W, 9 Slots (127 x 127 x 279.4) 3 = 5” x 8” x 11”; 1800 W - 4500 W, 14 Slots (127 x 203.2 x 279.4) 3-Phase Input 6 = 5” x 5” x 11”; 3120 W, 9 Slots (127 x 127 x 279.4) 8 = 5” x 8” x 11”; 4920 W, 14 Slots (127 x 203.2 x 279.4) 8H= 5” x 8” x 11”; 4920 W, 14 Slots (127 x 203.2 x 279.4) Module Codes Module/voltage/option codes Module Codes: (None) = 36 W triple O/P (1 slot) 1 = 210 W single O/P (1 slot) 2 = 360 W single O/P (2 slot) 3 = 750 W single O/P (3 slot) 5 = 1500 W single O/P (slot 4) 4 = 144 W dual O/P (1 slot) HUP = Extra 30mS hold-up (1 slot) Voltage Codes: See Output Module Voltage/Current table above Option Codes: 0 = Standard 1 = Module enable 2 = Constant current 3 = 1 & 2 combined 4 = Set for use in standard (non-intelligent case) 5 = Shutdown mode for 1500 W 6 = 1 & 5 combined 7-9 Future Parallel Code Slot No. 1 1&2 Case Option Codes Case Option Codes First Digit 0 - 9 = Parallel code (See parallel codes table below) Second Digit 0 = No options 1 = Reverse air 2 = Not used 3 = Global enable 4 = Fan Off w/inhibit 5 = Opt 1 + Opt 3 6 = Opt 1 + Opt 4 7 = Opt 3 + Opt 4 8 = Opt 1 + 3 + 4 9 = Future iVS1, 6 Diagram AC 9 8 7 6 210 210; 210 144; 144 144 2&3 AC 9 8 7 6 3&4 4 5 4&5 3, 4, & 5 360 360; 360 210; 360 144; + above 4&6 AC 14 13 12 11 10 9 5 4 3 2 1 1500 210; 1500 144; 210 210; 210 144; 144 144; 360 210; 360 144 8 7 6 5 4 3 2 1 AC 9 8 7 6 750 210 210; 750 210 144; 750 144 144 AC 9 8 7 6 AC 9 8 7 6 Possible Configurations 210 210; 210 144; 144 144 360 360; 360 210; 360 144; + above 8 7 6 5 4 3 2 1 AC 14 13 12 11 10 9 AC 14 13 12 11 10 9 AC 14 13 12 11 10 9 750 750; 750 360; 750 210; 750 144; 210 210; 210 144; 144 144 1500 1500; 1500 750; 1500 360; 1500 210; 1500 144; 210 210; 210 144; 144 144; 360 360; 360 210; 360 144 750 210 210; 750 210 144; 750 144 144 8 7 6 5 4 3 2 1 5 4 3 2 1 6 AC 14 13 12 11 10 9 8 7 6 5 4 3 2 1 5 4 3 2 1 Factory assembled for hardware of firmware mods. Ordering Note: 1. USB to I2C module order code 73-769-001 Diagram 750 360; 750 210; 750 144; 210 210; 210 144; 144 144 AC 9 8 7 6 Software code used for configuration change. “A” is standard ### 8 7 6 5 4 3 2 1 5 4 3 2 1 3 - A iVS3, 8, 8H Possible Configurations 5 4 3 2 1 2 - 00 Hardware Code Software Code 1500 1500; 1500 750 5 4 3 2 1 7 4, 5, & 6 AC 9 8 7 6 5 4 3 2 1 8 9 A C E iVS1,6: 3 & 6 iVS3,8,8H: 4, 5, & 9 AC 9 8 7 6 iVS1,6: 1 & 6 iVS3, 8, 8H: 4, 5 & 9; 12 & 13 AC 9 8 7 6 iVS1,6: 3 & 4; 8 & 9 iVS3, 8, 8H: 4 & 5; 11 & 12 AC 9 8 7 6 iVS1,6: 3, 4 & 6 iVS3, 8, 8H: 6 & 7; 3, 4, 11 & 12 AC 9 8 7 6 iVS3, 8, 8H: 3, 4, 11, & 12 1500 210 210; 1500 210 144; 1500 144 144 750 750 AC 14 13 12 11 10 9 8 7 6 5 4 3 2 1 5 4 3 2 1 1500 1500; 1500 360; 1500 144 AC 14 13 12 11 10 9 8 7 6 5 4 3 2 1 5 4 3 2 1 750 210 & 750 210 5 4 3 2 1 5 4 3 2 1 AC 14 13 12 11 10 9 1500 210 210; 1500 210 144; 1500 144 144 8 7 6 5 4 3 2 1 AC 14 13 12 11 10 9 1500 1500 1500; 1500 1500 750; 1500 1500 360; 1500 1500 210; 1500 1500 144 1500 1500 1500 360; 1500 1500 1500 210; 1500 1500 1500 144 1500 1500 & 750 750 8 7 6 5 4 3 2 1 750, 360, 750 AC 14 13 12 11 10 9 750 750 360 750 750 8 7 6 5 4 3 2 1 AC 14 13 12 11 10 9 750 750 750 750 8 7 6 5 4 3 2 1 F iVS3, 8, 8H: 3 & 4; 11 & 12 AC 14 13 12 11 10 9 750 360 & 750 210; 750 750 & 750 750 8 7 6 5 4 3 2 1 G iVS3, 8, 8H: 3,4 & 9 H iVS3, 8, 8H: 11 & 12 AC 14 13 12 11 10 9 8 7 6 5 4 3 2 1 AC 14 13 12 11 10 9 8 7 6 5 4 3 2 1 750 750 750 750 750 Embedded Power for Business-Critical Continuity Rev. 7.9.09_145 iVS Series of 11 iVS Case Specifications iVS1 and iVS6 S L O T 5 Input 7 S L O T 6 S L O T S L O T S L O T 3 2 1 iVS6 = 5” x 5” x 11” N/A (127 x 127 x 279.4) 9 available slots 3-phase only S L O T S L O T S L O T 9 8 S L O T 4 90-264 Vac iVS1 = 5” x 5” x 11” 1500 W max. (127 x 127 x 279.4) 9 available slots 170-264 Vac 3210 W max. 170-264 Vac 3210 W max. iVS3, iVS8, and iVS8H S L O T S L O T 8 7 S L O T 14 S L O T 13 S L O T 12 S L O T 11 S L O T 10 S L O T 9 S L O T 6 S L O T 5 S L O T 4 S L O T 3 S L O T 2 S L O T 1 90-264 Vac Input 170-264 Vac iVS3 = 5” x 8” x 11” 1800 W max. (127 x 203.2 x 279.4) 14 available slots 4500 W max. iVS8 = 5” x 8” x 11” N/A (127 x 203.2 x 279.4) 1 14 available slots 2 iVS8H =5” x 8” x 11” N/A (127 x 203.2 x 279.4) 3 14 available slots 170-264 Vac 4920 W max. N ~ 380 Vac 3800 W max. 480 Vac 4920 W max. Figure 1. AC Input Pin Connectors AC Input Single Phase Figure 1. AC Input Pin No. 1 N 2 ~ 3 1 L 2 L 3 L 3 4 iVS6 iVS1, iVS3 L 4 3 L 2 1 2 4 3 Phase Function 1 AC neutral 1 AC line N (hot) 2 2 Chassis (earth) ground 3 3 Chassis (earth) 4 ~ Line 1 φ1 2 Line φ2 Line 3 φ3 ground L 1 iVS8, iVS8H I2C Bus Output Connector Figure 3. Connector J2 Mates with Landwin 2050S1000 housing 2053T011P pin Connector Kit Part No.: 70-841-023 Pin No. 1 2 3 4 5 6 7 8 9 10 Function No connection No connection No connection Serial clock signal (SCL) Serial data signal (SDA) Address bit 0 (A0) Address bit 1 (A1) Address bit 2 (A2) Secondary return (GND) 5 VCC external bus (5 VCC bus) Figure 2. Connector J1 PFC Input Connector (control & signals) Pin No. 1 1 5 2 6 10 3 Mates with Figure 2. Connector J1 4 Molex 90142-0010 Housing 90119-2110 Pin 5 Connector Kit Part No.: 6 70-841-004 7 8 9 10 Function Input AC OK - “emitter” Input AC OK - “collector” Global DC OK - “emitter” Global DC OK - “collector” No connection Global inhibit/optional enable logic “0” Global inhibit/optional enable logic “1” Global inhibit/optional enable return +5 VSB housekeeping +5 VSB housekeeping return Embedded Power for Business-Critical Continuity iMP Modules DC-DC Converter Output Modules Rev. 7.9.09_145 iVS Series of 11 Control Signal Information, J1 Control Connector Single 210 Watt .44” (11.2) Function 1 2 3 4 5 6 7 8 9 10 + Remote Sense single or dual o/p main Remote Margin / V. Program single o/p N Margin High1 single o/p - Remote Sense / Margin Low single or dual o/p main 2 Spare 3 Module, Isolated Inhibit single or dual o/p Module Inhibit return single or dual o/p Current Share (SWP) single or dual o/p main + Remote Sense V2 dual o/p, single is spare Figure 1. AC Input - Remote Sense V2 dual o/p, single is spare *Note: All iMP modules have a green DCOK LED. (except for 36 W module) 2X .48" ~ (12.1) Pin No. M4X8 SCREWS WITH CONICAL WASHER 1.38" (35.1) V- .44" (11.4) V ADJ PIN 1 DC OUTPUT CONNECTOR Figure 4. Connector J1 1 5 6 10 V+ .32" (8.1) Mates with Figure 2. Connector J1 Molex 90142-0010 Housing 90119-2110 Pin Single 750 Watt Single 360 Watt .63” .33” (16.0) (8.5) V+ .63" (16.0) Single 1500 Watt .59" (15.0) V+ V ADJ .61"(15.6) (2X) .44" (11.0) 1.38” (35.2) (2X) .44” (11.4) VPIN 1 1.24"(11.0) (2X) .48” (12.1) (2X) M 4 X 8 SCREWS WITH CONICAL WASHER DC OUTPUT CONNECTOR .32” (8.1) .32" (8.1) V1 + (4X) V1 V2 + V2 - .30 (7.5)(3X) M3X8 SCREWS WITH SPRING WASHER (4X) 1.17 (29.7) .42 (10.7) .32 (8.1) N D CO C O NN UTP EC UT TO R Dual 144 Watt .46 (11.7) PI V2 ADJ V1 ADJ PIN 1 1 V AD J M (4 4X8 X) S C VRE W S V- V+ Triple 36 Watt V1 ADJ V2 ADJ V1+ V2+ V3+ V3 ADJ V1 + V1- V1 - V2- V2 + V2 - V3- V3 + V3 - Mates with Molex 09-91-0600 Housing 26-60-5060 Pin w Embedded Power for Business-Critical Continuity iVS Series Rev. 7.9.09_145 iVS Series of 11 5-Inch Case Size: iVS1: 5” x 5” x 11” (127mm x 127mm x 279.4mm) Weight: iVS1 Case: 6.2 lbs. • 1500 W Single: 2.0 lbs. • 750 W Single: 1.6 lbs. • 360 W Single: 1.0 lb.• 210 W Single: 0.6 lb. • 144 W Dual: 0.6 lb. iVS1 (1500/3210 Watts Max) REVERSE AIRFLOW DIRECTION NORMAL AIRFLOW DIRECTION 127.0 ± 0.5 B B A 279.40 ± 1.27 127.0 ± 0.5 63.5 AC INPUT CONNECTOR FAN 92 X 92 X 38mm L N PE 127.0 ± 0.9 127.0 ± 0.9 101.6 ± 0.9 C USB PROGRAMMING CONNECTOR OPTION 65.5 SELV CONTROL CONNECTOR I2C C CONNECTOR 12.7 OUTPUT MODULE AREA 19.1 171.5 M4 MTG HOLES 4 PL 11.6 AC OK LED DC OK LED 13.5 33.5 12.0 57.4 “MOUNTING HOLES DIMENSIONS IDENTICAL ON BOTH SIDES” 171.45 29.05 5.00 12.70 B 114.30 22.80 Notes 19.05 171.45 A 1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m). 2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m). 6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. (0.57 N-m). C w Embedded Power for Business-Critical Continuity iVS Series iVS3 (1800/4500 Watts Max) Rev. 7.9.09_145 iVS Series of 11 8-Inch Case Size: iVS3: 5” x 8” x 11” (127mm x 203.2mm x 279.4mm) Weight: iVS3 Case: 9.0 lbs. • 1500 W Single 2.0 lbs.• 750 W Single: 1.6 lbs. • 360 W Single: 1.0 lb. • 210 W Single: 0.6 lb. •144 W Dual: 0.6 lb. REVERSE AIRFLOW DIRECTION NORMAL AIRFLOW DIRECTION B 203.2±0.5 98 279.4±1.27 OT 52.6 A 12.7 USB PROGRAMMING CONNECTOR OPTION I2C 1 OT 2 SL OT SL SL OT 3 4 SL OT SL OT SL OT 5 7 6 8 OT OT SL 171.45 A 11.6 SELV CONTROL CONNECTOR C C DC OK LED 42 M4 MTG HOLES 4 PL AC OK LED 61.2 19.1 81.5 29.1 #8-32 MTG HOLES 5PL MARKED “A” 6, 7 REF 171.5 B A B A B A B B A 177.8 149.4 173.3 12.7 14.4 “MOUNTING HOLES DIMENSIONS IDENTICAL ON BOTH SIDES B A 16.2 19.1 Notes 171.5 M4 MTG HOLES 5 PL MARKED “B” A 1. Input: Barrier type. Three M4 screws (0.512” centers). Max torque: 7 in-lbs. (0.79 N-m). 2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m). 6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. (0.57 N-m). 65.5 127±0.9 101.6 ± 0.9 OUTPUT MODULE AREA SL FAN 80 X 80 X 38mm SL OT SL A 9 11 10 12 OT SL OT SL SL SL OT AC INPUT CONNECTOR OT 14 13 B C w Embedded Power for Business-Critical Continuity iVS Series iVS6 (3210 Watts Max) Rev. 7.9.09_145 iVS Series of 11 5-Inch Case Size: iVS6: 5” x 5” x 11” (127mm x 127mm x 279.4mm) Weight: iVS6 Case: 6.0 lbs. • 1500 W Single 2.0 lbs. • 750 W Single: 1.6 lbs. • 360 W Single: 1.0 lb. • 210 W Single: 0.6 lb. •144 W Dual: 0.6 lb. 279.4±1.0 5.0±0.5 NORMAL AIRFLOW DIRECTION REVERSE AIRFLOW DIRECTION 293.0±1.2 57.4 171.5 (2X) SLOT 6 SLOT 9 SLOT 7 101.6±0.9 (2X) SLOT 2 SLOT 1 SLOT 3 12.7 (2X) 171.5 (2X) SLOT 4 12.7 (2X) FOR M4 SCREW (4X) (FOR SYSTEM MOUNTING) 19.1 (2X) 171.5 (2X) 19.1 (2X) 12.0 19.1 (2X) 12.7 (4X) 33.5 DC OK LED 11.6 (2X) SELV CONTROL CONNECTOR 13.5 SLOT 5 101.6±0.9 (2X) 65.5 127.0±0.9 AC OK LED I2C CONNECTOR L1 L2 L3 L1 L2 L3 INTERNAL FUSES 15A/250V USB PROGRAMMING CONNECTOR OPTION 12.6±0.6 AC INPUT CONNECTOR SLOT 8 GND 20.3±0.6 127.0±0.5 63.5 12.7 (4X) FOR #8-32 SCREW (4X) (SYSTEM MOUNTING) FOR M4 SCREW (4X) (FOR SYSTEM MOUNTING) 171.5 (2X) Notes 29.1 (2X) 1. Input: Barrier type. Four M3 screws (0.325” centers). Max torque: 6 in-lbs. (0.67 N-m). 2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m). 6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. (0.57 N-m). FOR M4 SCREW (4X) (FOR SYSTEM MOUNTING) w Embedded Power for Business-Critical Continuity Rev. 7.9.09_145 iVS Series 10 of 11 8-Inch Case Size: iVS8: 5” x 8” x 11” (127mm x 203.2mm x 279.4mm) Weight: iVS8 Case: 9.0 lbs. • 1500 W Single 2.0 lbs. • 750 W Single: 1.6 lbs. • 360 W Single: 1.0 lb. • 210 W Single: 0.6 lb. •144 W Dual: 0.6 lb. iVS Series iVS8 (4920 Watts Max) 6.8 max (2x) NORMAL AIRFLOW DIRECTION REVERSE AIRFLOW DIRECTION 291.1±1.2 279.4±0.2 USB Programming Connector Option 7 12.7 (2x) 31.8 50.7 72.1 MOSYTEM Mounting for #8-32 Screw (5X) (’a’) Notes 19.1 (2x) 171.5 (2x) 171.5 (2x) 171.5 (2x) 19.1 (3x) 14.4 (2x) 12.7 (2x) SELV Control Connector 19.1 (2x) GND Terminal 15.5 (2x) 23.9 (2x) MOSYTEM Mounting for M4 Screw (I3X) (’a’) I2C Connector 101.6±0.9 12.7 (2x) 11.6 (2x) 65.5 (2x) 127.0±0.2 AC Input Connector 101.6±0.9 12.7 (2x) 203.2±0.2 155.6 52.6 29.1 (3x) 171.5 (2x) 1. Input: Barrier type. Three M3.5 screws (0.394” centers). Max torque: 6 in-lbs. (0.67 N-m). 2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m). 6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. (0.57 N-m). ss w Embedded Power for Business-Critical Continuity Optional CANBUS or RS485 Interface Americas 5810 Van Allen Way Carlsbad, CA 92008 USA The Input Protocols used are RS485 using Modbus (Command Index: 0x01), and CAN using modified Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 Modus (Command Index: 0x02). Rev. 7.9.09_145 iVS Series 11 of 11 The RS485/CAN-to-I2C uses 2 Input Protocols and 1 Output Protocol. The Output Protocol use is: I2C with SMBus support (Command Index: 0x80). S lav e/S erv er D ev ice(s) A d ap te r Europe (UK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Asia (HK) 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 O u tp u t P ro toco ls I 2 C w ith S M B us S upport For global contact, visit: A dapter P rotoc ol www.PowerConversion.com A d ap t e r C om m a n d A d a p te r C o n tro ls techsupport.embeddedpower @emerson.com While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Inp ut P rotocols R S 485 us in g M o dbus C AN usin g M o difie d M od bus Emerson Network Power. The global leader in enabling business-critical continuity. AC Power Connectivity DC Power M aster/C lie nt D ev ice(s) Embedded Computing RS485/CAN - to - I2C Embedded Power For Detailed Info, Download the Software Requirements Specification (SRS) from www.PowerConversion.com/products/cat/103/iVS-series-ac-dc-power-supplies Monitoring Outside Plant Power Switching & Controls Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2009 Emerson Electric Co. iVS CAN RS485 iVS I2C USB