SSOUSA AD6C431 400ma maximum continuous load current Datasheet

AD6C431
1 Form A
Solid State Relay
DESCRIPTION
The AD6C431 is a bi-directional, single-pole, single-throw, normally open multipurpose relay. It is designed to replace electro-mechanical
relays in many higher load current applications. The relay consists of an integrated circuit that drives two rugged drain-to-drain
enhancement type DMOS transistors - optically coupled to a light emitting diode. The output MOS transistors have low on resistance,
making the relays ideal where switching higher current loads is required.
FEATURES
APPLICATIONS
•
400mA maximum continuous load current
•
Reed relay replacement
•
200V Blocking Voltage
•
Meter reading systems
•
3 Ohms maximum on-resistance
•
Medical equipment
•
High input-to-output isolation
•
Battery monitoring
•
Long life/high reliability
•
Multiplexers
•
Low input control power consumption
OPTIONS/SUFFIXES*
•
-S
Surface Mount Leadform Option
•
-TR
Tape and Reel Option
NOTE: Suffixes listed above are not included in marking on
device for part number identification.
SCHEMATIC DIAGRAM
ABSOLUTE MAXIMUM RATINGS*
PARAMETER
UNIT
MIN
Storage Temperature
°C
-55
125
Operating Temperature
°C
-40
85
Continuous Input Current
mA
40
Transient Input Current
mA
400
Reverse Input Control
Voltage
V
Output Power Dissipation
mW
TYP
MAX
6
800
*The values indicated are absolute stress ratings. Functional operation of the
device is not implied at these or any conditions in excess of those defined in
electrical characteristics section of this document. Exposure to Absolute
Ratings may cause permanent damage to the device and may adversely
affect reliability.
APPROVALS
© 2004 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
•
BABT: Pending
•
UL/C-UL: Pending
Page 1 of 5
AD6C431
rev 1.4 (10/25/04)
AD6C431
1 Form A
Solid State Relay
ELECTRICAL CHARACTERISTICS - 25°C
PARAMETER
UNIT
MIN
TYP
MAX
1.2
1.5
TEST CONDITIONS
INPUT SPECIFICATIONS
LED Forward Voltage
V
LED Reverse Voltage
6
12
V
Turn-On Current
mA
2.5
Turn-Off Current
mA
0.5
If = 10mA
Ir = 10uA
5
Io = 400mA
OUTPUT SPECIFICATIONS
Blocking Voltage
V
Continuous Load Current
mA
On-Resistance
Leakage Current
200
Io = 1uA
400
If = 5mA
Ω
1.5
3
Io = 400mA
µA
0.2
10
Vo = 200V
Output Capacitance
pF
125
200
Vo = 25V, f = 1.0MHz
Offset Voltage
mV
0.2
If = 5mA
COUPLED SPECIFICATIONS
Isolation Voltage
-H Suffix
Turn-On Time
V
2500
V
3750
T = 1 minute
T = 1 minute
ms
1.65
5
If = 5mA, Io = 400mA
Turn-Off Time
ms
0.5
1
If = 5mA, Io = 400mA
Isolation Resistance
GΩ
Coupled Capacitance
pF
Contact Transient Ratio
V/
© 2004 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
100
2
µs
2000
Page 2 of 5
7000
dV = 50V
AD6C431
rev 1.4 (10/25/04)
AD6C431
1 Form A
Solid State Relay
PERFORMANCE DATA
AD6C431
AD6C431
Typical Turn-On Time Distribution
N = 100, Ambient Temperature = 25°C
Typical Turn-Off Time Distribution
N = 100, Ambient Temperature = 25°C
40
Device Count
40
30
20
10
0
30
20
10
0
1
1.2
1.4
1.6
1.8
2
2.2
2.4
0
0.03 0.05 0.08 0.1 0.13 0.15 0.18
Turn-On Tim e (m s)
Turn-Off Tim e (m s)
AD6C431
AD6C431
Typical On-Resistance Distribution
N = 100, Ambient Temperature = 25°C
Typical Leakage Current Distribution
N = 100, Ambient Temperature = 25°C
40
Device Count
30
20
10
0
30
20
10
0
1.15 1.2 1.25 1.3 1.35 1.4 1.45 1.5
0.01 0.01 0.02 0.02 0.03 0.03 0.04 0.04
On-Resistance (ohm s)
AD6C431
Maximum Load Current vs. Temperature
Blocking Voltage (V)
© 2004 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
0
80
200 210 220 230 240 250 260 270
60
0
200
100
40
10
400
300
-2
0
20
500
-4
0
30
Load Current (mA)
AD6C431
Typical Blocking Voltage Distribution
N = 100, Ambient Temperature = 25°C
40
Device Count
Leakage Current (uA)
20
Device Count
40
0
Device Count
50
Tem perature (C)
Page 3 of 5
AD6C431
rev 1.4 (10/25/04)
AD6C431
1 Form A
Solid State Relay
MECHANICAL DIMENSIONS
6 PIN DUAL IN-LINE PACKAGE
6 PIN SURFACE MOUNT DEVICE
END VIEW
END VIEW
TOP VIEW
TOP VIEW
BOTTOM VIEW/
BOARD PATTERN
BOTTOM VIEW/
BOARD PATTERN
© 2004 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 4 of 5
AD6C431
rev 1.4 (10/25/04)
AD6C431
1 Form A
Solid State Relay
DISCLAIMER
Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO
reserves the right to make changes to product description, specifications at any time without further notice.
SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent
licenses nor indemnity are expressed or implied.
Except as specified in SSO's Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other
warranty, expressed or implied, including merchantability and fitness for particular use.
LIFE SUPPORT POLICY
SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or
death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all
damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be
reasonably expected to result in significant injury to the user, or (d) a critical component in any component of a life support device or system
whose failure can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness.
© 2004 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 5 of 5
AD6C431
rev 1.4 (10/25/04)
Similar pages