E2G0028-17-41 ¡ Semiconductor MSM518200 ¡ Semiconductor This version:MSM518200 Jan. 1998 Previous version: May 1997 4,194,304-Word ¥ 2-Bit DYNAMIC RAM : FAST PAGE MODE TYPE DESCRIPTION The MSM518200 is a 4,194,304-word ¥ 2-bit dynamic RAM fabricated in Oki's silicon-gate CMOS technology. The MSM518200 achieves high integration, high-speed operation, and low-power consumption because Oki manufactures the device in a quadruple-layer polysilicon/double-layer metal CMOS process. The MSM518200 is available in a 26/24-pin plastic SOJ or 26/24-pin plastic TSOP. FEATURES • 4,194,304-word ¥ 2-bit configuration • Single 5 V power supply, ±10% tolerance • Input : TTL compatible, low input capacitance • Output : TTL compatible, 3-state • Refresh : 4096 cycles/64 ms • Fast page mode, read modify write capability • CAS before RAS refresh, hidden refresh, RAS-only refresh capability • Multi-bit test mode capability • Package options: 26/24-pin 300 mil plastic SOJ (SOJ26/24-P-300-1.27) (Product : MSM518200-xxSJ) 26/24-pin 300 mil plastic TSOP (TSOPII26/24-P-300-1.27-K) (Product : MSM518200-xxTS-K) xx indicates speed rank. PRODUCT FAMILY Family Access Time (Max.) tRAC tAA tCAC tOEA Cycle Time Power Dissipation (Min.) Operating (Max.) Standby (Max.) MSM518200-60 60 ns 30 ns 15 ns 15 ns 110 ns 385 mW MSM518200-70 70 ns 35 ns 20 ns 20 ns 130 ns 358 mW MSM518200-80 80 ns 40 ns 20 ns 20 ns 150 ns 330 mW 5.5 mW 1/17 ¡ Semiconductor MSM518200 PIN CONFIGURATION (TOP VIEW) VCC 1 26 VSS VCC 1 26 VSS DQ1 2 25 NC DQ1 2 25 NC DQ2 3 24 CAS1 DQ2 3 24 CAS1 WE 4 23 CAS2 WE 4 23 CAS2 RAS 5 22 OE RAS 5 22 OE A11R 6 21 A9 A11R 6 21 A9 A10R 8 19 A8 A10R 8 19 A8 A0 9 18 A7 A0 9 18 A7 A1 10 17 A6 A1 10 17 A6 A2 11 16 A5 A2 11 16 A5 A3 12 15 A4 A3 12 15 A4 VCC 13 14 VSS VCC 13 14 VSS 26/24-Pin Plastic SOJ Pin Name A0 - A9, A10R, A11R RAS Note : 26/24-Pin Plastic TSOP (K Type) Function Address Input Row Address Strobe CAS1, CAS2 Column Address Strobe DQ1, DQ2 Data Input/Data Output OE Output Enable WE Write Enable VCC Power Supply (5 V) VSS Ground (0 V) NC No Connection The same power supply voltage must be provided to every VCC pin, and the same GND voltage level must be provided to every VSS pin. 2/17 ¡ Semiconductor MSM518200 BLOCK DIAGRAM Timing Generator RAS Timing Generator CAS1 CAS2 10 Column Address Buffers Write Clock Generator Column Decoders 10 WE OE 2 Internal Address Counter A0 - A9 Refresh Control Clock Sense Amplifiers 2 I/O Selector A10R, A11R 2 Row Address Buffers 12 Row Decoders Word Drivers 2 2 2 2 10 Output Buffers Input Buffers DQ1, DQ2 2 Memory Cells VCC On Chip VBB Generator VSS FUNCTION TABLE Input Pin DQ Pin Function Mode RAS CAS1 CAS2 WE OE DQ1 DQ2 H * H * H * * High-Z High-Z Standby L High-Z Refresh L L H * L High-Z DOUT High-Z DQ1 Read DOUT DQ2 Read * H L H L H L High-Z L L L H L DOUT DOUT DQ1, DQ2 Read L L H L H DIN L H L L H Don't Care Don't Care DIN DQ2 Write L L L L H DIN DIN DQ1, DQ2 Write L L L H H High-Z High-Z — DQ1 Write *: "H" or "L" 3/17 ¡ Semiconductor MSM518200 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings Parameter Symbol Rating Unit VT –1.0 to 7.0 V Short Circuit Output Current IOS 50 mA Power Dissipation PD* 1 W Operating Temperature Topr 0 to 70 °C Storage Temperature Tstg –55 to 150 °C Voltage on Any Pin Relative to VSS *: Ta = 25°C Recommended Operating Conditions Parameter Power Supply Voltage (Ta = 0°C to 70°C) Symbol Min. Typ. Max. Unit VCC 4.5 5.0 5.5 V VSS 0 0 0 V Input High Voltage VIH 2.4 — 6.5 V Input Low Voltage VIL –1.0 — 0.8 V Capacitance Parameter Input Capacitance (A0 - A9, A10R, A11R) Input Capacitance (RAS, CAS1, CAS2, WE, OE) Output Capacitance (DQ1, DQ2) (VCC = 5 V ±10%, Ta = 25°C, f = 1 MHz) Symbol Typ. Max. Unit CIN1 — 6 pF CIN2 — 7 pF CI/O — 10 pF 4/17 ¡ Semiconductor MSM518200 DC Characteristics Parameter (VCC = 5 V ±10%, Ta = 0°C to 70°C) Symbol Condition MSM518200 MSM518200 MSM518200 -60 -70 -80 Unit Note Min. Max. Min. Max. Min. Max. Output High Voltage VOH IOH = –5.0 mA 2.4 VCC 2.4 VCC 2.4 VCC V Output Low Voltage VOL IOL = 4.2 mA 0 0.4 0 0.4 0 0.4 V –10 10 –10 10 –10 10 mA –10 10 –10 10 –10 10 mA — 70 — 65 — 60 mA 1, 2 — 2 — 2 — 2 — 1 — 1 — 1 — 70 — 65 — 60 mA 1, 2 — 5 — 5 — 5 mA — 70 — 65 — 60 mA 1, 2 — 60 — 55 — 50 mA 1, 3 0 V £ VI £ 6.5 V; Input Leakage Current ILI All other pins not under test = 0 V Output Leakage Current Average Power Supply Current (Operating) Power Supply Current (Standby) ILO DQ disable 0 V £ VO £ 5.5 V RAS, CAS1, CAS2 ICC1 cycling, tRC = Min. RAS, CAS1, CAS2 = VIH ICC2 RAS, CAS1, CAS2 ≥ VCC –0.2 V Average Power RAS cycling, Supply Current ICC3 CAS1, CAS2 = VIH, (RAS-only Refresh) Power Supply Current (Standby) RAS = VIH, ICC5 CAS1, CAS2 = VIL, 1 DQ = enable RAS cycling, Supply Current ICC6 CAS1, CAS2 (CAS before RAS Refresh) before RAS Average Power RAS = VIL, (Fast Page Mode) 1 tRC = Min. Average Power Supply Current mA ICC7 CAS1, CAS2 cycling, tPC = Min. Notes : 1. ICC Max. is specified as ICC for output open condition. 2. The address can be changed once or less while RAS = VIL. 3. The address can be changed once or less while CAS1, CAS2 = VIH. 5/17 ¡ Semiconductor MSM518200 AC Characteristics (1/2) (VCC = 5 V ±10%, Ta = 0°C to 70°C) Note 1, 2, 3, 11, 12 Parameter Random Read or Write Cycle Time Read Modify Write Cycle Time Fast Page Mode Cycle Time Fast Page Mode Read Modify Write Cycle Time Access Time from RAS MSM518200 MSM518200 MSM518200 -60 -70 -80 Symbol Unit Note Min. Max. Min. Max. Min. Max. tRC tRWC 110 — — 130 — ns 185 — ns tPC 40 — 45 — — 150 205 — 155 50 — ns tPRWC 85 — 100 — 105 — ns tRAC — 60 — 70 — 80 ns 4, 5, 6 Access Time from CAS tCAC Access Time from Column Address Access Time from CAS Precharge tAA tCPA — — 15 30 — — 20 35 — — 20 40 ns ns 4, 5 4, 6 — 35 — 40 — 45 ns 4, 14 Access Time from OE Output Low Impedance Time from CAS tOEA tCLZ — 0 15 — — 0 20 — — 0 20 — ns ns 4 4 CAS to Data Output Buffer Turn-off Delay Time tOFF 20 50 64 0 0 3 — 20 15 50 64 0 0 3 — 20 tOEZ tT tREF 0 0 3 — 15 OE to Data Output Buffer Turn-off Delay Time Transition Time Refresh Period 20 50 64 ns ns ns ms 7 7 3 RAS Precharge Time tRP 40 — 50 — 60 — ns RAS Pulse Width tRAS 60 10,000 70 10,000 80 10,000 ns RAS Pulse Width (Fast Page Mode) tRASP 60 100,000 70 100,000 80 100,000 ns RAS Hold Time tRSH RAS Hold Time referenced to OE tROH 15 10 — — 20 10 — — 20 10 — — ns ns CAS Precharge Time (Fast Page Mode) tCP 10 — 10 — 10 — ns CAS Pulse Width tCAS 15 10,000 20 10,000 20 10,000 ns CAS Hold Time tCSH — — 70 10 — — — — ns tCRP 60 10 80 CAS to RAS Precharge Time ns 14 RAS Hold Time from CAS Precharge RAS to CAS Delay Time RAS to Column Address Delay Time tRHCP — 45 40 ns ns ns 5 35 45 20 15 — 60 30 40 20 15 — 50 tRAD 35 20 15 Row Address Set-up Time tASR 0 — 0 — 0 — ns Row Address Hold Time tRAH 10 — 10 — 10 — ns Column Address Set-up Time tASC 0 — 0 — 0 — ns 13 Column Address Hold Time tCAH 15 — 15 — 15 — ns 13 Column Address Hold Time from RAS tAR 50 — 55 — 60 — ns Column Address to RAS Lead Time tRAL 30 — 35 — 40 — ns Read Command Set-up Time tRCS 0 — 0 — 0 — ns 13 Read Command Hold Time tRCH 0 — 0 — 0 — ns 8, 13 Read Command Hold Time referenced to RAS tRRH 0 — 0 — 0 — ns 8 tRCD 10 16 6 6/17 ¡ Semiconductor MSM518200 AC Characteristics (2/2) (VCC = 5 V ±10%, Ta = 0°C to 70°C) Note 1, 2, 3, 11, 12 Parameter MSM518200 MSM518200 MSM518200 -60 -70 -80 Unit Note Symbol Min. Max. Min. Max. Min. Max. Write Command Set-up Time tWCS 0 — 0 — 0 — ns 9, 13 Write Command Hold Time Write Command Hold Time from RAS tWCH tWCR 10 45 — — 15 55 — — 15 60 — — ns ns 13 Write Command Pulse Width OE Command Hold Time tWP tOEH tRWL tCWL 10 15 — — 10 20 — — 10 20 — — ns ns 15 15 — — 20 20 — — 20 20 — — ns ns 15 Data-in Hold Time Data-in Hold Time from RAS OE to Data-in Delay Time CAS to WE Delay Time Column Address to WE Delay Time RAS to WE Delay Time tDS tDH tDHR tOED tCWD tAWD tRWD 0 15 — — 0 15 — — 0 15 — — ns ns 10, 13 10, 13 50 15 — — 55 20 — — 60 20 — — ns ns 40 55 85 — — — 50 65 100 — — — 50 70 110 — — — ns ns ns 9 9 9 CAS Precharge WE Delay Time tCPWD 60 — 70 — 75 — ns 9, 14 CAS Active Delay Time from RAS Precharge tRPC 10 — 10 — 10 — ns 13 RAS to CAS Set-up Time (CAS before RAS) RAS to CAS Hold Time (CAS before RAS) tCSR tCHR 10 20 — — 10 20 — — 10 20 — — ns ns 13 14 WE to RAS Precharge Time (CAS before RAS) WE Hold Time from RAS (CAS before RAS) RAS to WE Set-up Time (Test Mode) RAS to WE Hold Time (Test Mode) tWRP tWRH tWTS tWTH 10 10 10 20 — — — — 10 10 10 20 — — — — 10 10 10 20 — — — — ns ns ns ns Write Command to RAS Lead Time Write Command to CAS Lead Time Data-in Set-up Time 7/17 ¡ Semiconductor Notes: MSM518200 1. A start-up delay of 200 µs is required after power-up, followed by a minimum of eight initialization cycles (RAS-only refresh or CAS before RAS refresh) before proper device operation is achieved. 2. The AC characteristics assume tT = 5 ns. 3. VIH (Min.) and VIL (Max.) are reference levels for measuring input timing signals. Transition times (tT) are measured between VIH and VIL. 4. This parameter is measured with a load circuit equivalent to 2 TTL loads and 100 pF. 5. Operation within the tRCD (Max.) limit ensures that tRAC (Max.) can be met. tRCD (Max.) is specified as a reference point only. If tRCD is greater than the specified tRCD (Max.) limit, then the access time is controlled by tCAC. 6. Operation within the tRAD (Max.) limit ensures that tRAC (Max.) can be met. tRAD (Max.) is specified as a reference point only. If tRAD is greater than the specified tRAD (Max.) limit, then the access time is controlled by tAA. 7. tOFF (Max.) and tOEZ (Max.) define the time at which the output achieves the open circuit condition and are not referenced to output voltage levels. 8. tRCH or tRRH must be satisfied for a read cycle. 9. tWCS, tCWD, tRWD, tAWD and tCPWD are not restrictive operating parameters. They are included in the data sheet as electrical characteristics only. If tWCS ≥ tWCS (Min.), then the cycle is an early write cycle and the data out will remain open circuit (high impedance) throughout the entire cycle. If tCWD ≥ tCWD (Min.) , tRWD ≥ tRWD (Min.), tAWD ≥ tAWD (Min.) and tCPWD ≥ tCPWD (Min.), then the cycle is a read modify write cycle and data out will contain data read from the selected cell; if neither of the above sets of conditions is satisfied, then the condition of the data out (at access time) is indeterminate. 10. These parameters are referenced to the CAS leading edge in an early write cycle, and to the WE leading edge in an OE control write cycle, or a read modify write cycle. 11. The test mode is initiated by performing a WE and CAS before RAS refresh cycle. This mode is latched and remains in effect until the exit cycle is generated. In a test mode CA0 and CA1 are not used and each DQ pin now accesses 4-bit locations. Since all 2 DQ pins are used, a total of 8 data bits can be written in parallel into the memory array. In a read cycle, if 4 data bits are equal, the DQ pin will indicate a high level. If the 4 data bits are not equal, the DQ pin will indicate a low level. The test mode is cleared and the memory device returned to its normal operating state by performing a RAS-only refresh cycle or a CAS before RAS refresh cycle. 12. In a test mode read cycle, the value of access time parameters is delayed for 5 ns for the specified value. These parameters should be specified in test mode cycle by adding the above value to the specified value in this data sheet. 13. These parameters are determined by the falling edge of either CAS1 or CAS2, whichever is earlier. 14. These parameters are determined by the rising edge of either CAS1 or CAS2, whichever is later. 15. tCWL should be satisfied by both CAS1 and CAS2. 16. tCP is determined by the time both CAS1 and CAS2 are high. 8/17 ¡ Semiconductor MSM518200 Notes concerning CAS1 and CAS2 control Overlap the active-low timings of CAS1 and CAS2. Skew between CAS1 and CAS2 is allowed under the following conditions: (1) The timing specification for CAS1 and CAS2 should be met individually. (2) Different operation modes for CAS1/CAS2 are not allowed (as shown below). RAS CAS1 Delayed write CAS2 Early write WE (3) Closely separated CAS1/CAS2 control is not allowed. However, when the condition (tCP ≤ tUL) is satisfied, fast page mode can be performed. RAS CAS1 CAS2 tUL 9/17 E2G0094-17-41G ,,, , ,,,, ¡ Semiconductor MSM518200 TIMING WAVEFORM Read Cycle tRC tRP tRAS VIH – RAS VIL – tAR tCSH tCRP CAS tRCD VIH – VIL – Address VIL – tRSH tCAS tRAD tASR VIH – tCRP tRAH tASC tRAL tCAH Column Row tRCS WE OE VIH – VIL – tAA tROH tOEA VIH – VIL – tCAC tRAC DQ tRCH tRRH VOH – tOEZ Open VOL – tOFF Valid Data-out tCLZ "H" or "L" Write Cycle (Early Write) tRC tRP tRAS RAS VIH – VIL – tAR tCRP VIH – CAS VIL – WE VIH – VIL – tCSH tRCD tRSH tCAS tRAD tRAH tASR Address tCRP tASC Row tCAH Column tWCS tWCH VIH – tRWL VIH – VIL – tDS DQ tCWL tWP VIL – tWCR OE tRAL VIH – VIL – tDHR tDH Valid Data-in Open "H" or "L" 10/17 ,,, ¡ Semiconductor MSM518200 Read Modify Write Cycle tRWC tRAS RAS VIH – VIL – tRP tAR tCRP tCSH tCRP tRCD tRSH tCAS VIH – CAS VIL – tASR VIH – Address VIL – WE VIH – VIL – OE VIH – VIL – tRAH tASC tCAH Column Row tRAD tRWD tAA tAWD tRCS tOEA tOED tCAC tRAC DQ VI/OH– VI/OL– tCWL tRWL tWP tCWD tCLZ tOEZ Valid Data-out tOEH tDS tDH Valid Data-in "H" or "L" 11/17 ¡ Semiconductor MSM518200 ,,, ,, , Fast Page Mode Read Cycle tRASP VIH – RAS V – IL VIH – CAS VIL – Address WE VIH – VIL – tRP tAR tCRP tRHCP tPC tRCD tCP tASR tCP tCAS tCAS tRAD tRAH tASC tCSH tCAH tASC Column Row VIH – VIL – tCAC VOH – DQ VOL – Column tRCS tRCH tRRH tCPA tOEA tOFF tOEZ tRCH tAA tAA tCAC tOEA tOFF tCAC tOEZ tCLZ Valid Data-out tCLZ tRCS tCPA tOEA tRAC tRAL tCAH tASC Column tAA VIH – OE VIL – tCAS tCAH tRCH tRCS tCRP tRSH tCLZ tOFF tOEZ Valid Data-out Valid Data-out "H" or "L" Fast Page Mode Write Cycle (Early Write) tRASP tAR VIH – RAS V – IL tCRP VIH – CAS VIL – Address VIH – VIL – tRAH tASC Row VIH – VIL – tDS DQ VIH – VIL – tCSH tCAH Column tCWL tWCH tWP tRAD tRHCP tRSH tRCD tWCS WE tPC tCAS tASR tRP tWCR tDH Valid Data-in tDHR tCP tCRP tCP tCAS tASC tCAH tASC Column tCWL tWCS tWCH tWP tDS tDH Valid Data-in tCAS tCAH tRAL Column tRWL tCWL tWCS tWCH tWP tDS tDH Valid Data-in Note: OE = "H" or "L" "H" or "L" 12/17 ¡ Semiconductor MSM518200 ,,, , , , , Fast Page Mode Read Modify Write Cycle tRASP VIH – RAS VIL – tAR tRP tCSH tPRWC tRCD VIH – CAS VIL – tASC tCAH tRAH VIH – VIL – tCRP tCAS tASC tCAH tCAH Column Column tASC Column Row tRCS tCPWD tCWD tRWD tCWD tRCS V WE IH – VIL – tCWL tAWD tCWL tWP tDH VI/OH– VI/OL – Out tCLZ tOEA tOED tOEZ tCAC In tDH tDS tOEA tOEZ tCAC tWP tCPA tAA tOED VIH – OE V – IL tCWL tROH tWP tDH tDS tOEA tRWL tAWD tCPA tAA tAA tRAL tRCS tCPWD tCWD tAWD tDS tRAC DQ tCP tCAS tRAD tASR Address tCP tCAS tRSH Out tOED In tCLZ tOEZ tCAC Out In tCLZ "H" or "L" RAS-Only Refresh Cycle tRC RAS CAS Address VIL – VIH – VIL – VIH – VIL – tRP tRAS VIH – tCRP tASR tRPC tRAH Row tOFF DQ VOH – VOL – Open Note: WE, OE = "H" or "L" "H" or "L" 13/17 M L K ^ ] \ S R Q P ¡ Semiconductor MSM518200 CAS before RAS Refresh Cycle tRC tRP RAS tRP tRAS VIH – VIL – tRPC tRPC tCP CAS tCSR tCHR tWRP tWRH VIH – VIL – tWRP ,,, WE VIH – VIL – DQ VOH – VOL – tOFF Open Note: OE, Address = "H" or "L" "H" or "L" Hidden Refresh Read Cycle tRC tRAS RAS VIH – tRP tAR VIH – VIL – VIH – VIL – tRSH tRCD tRAD tASC tRAH tASR Address tRAS tRP VIL – tCRP CAS tRC Row tCHR tCAH Column tRCS tRAL VIH – WE V IL – tRRH tAA tROH tOEA VIH – OE V IL – tRAC DQ VOH – VOL – tCAC tCLZ tOFF tOEZ Valid Data-out "H" or "L" 14/17 ¡ Semiconductor MSM518200 Hidden Refresh Write Cycle tRC tRAS RAS CAS Address VIH – VIL – tRP tAR , ,,,, , VIH – VIL – VIH – VIL – tCRP tASR tRCD tRSH tRAD tASC tCAH tRAH Row WE VIH – VIL – OE VIH – VIL – tCHR tRAL Column tWCH tWP tWCS tDS DQ tRC tRAS tRP VIH – VIL – tWRP tWRH tDH Valid Data-in tDHR "H" or "L" Test Mode Initiate Cycle tRC tRP RAS VIH – VIL – tRPC tCP CAS tRAS tCSR VIH – VIL – tWTS WE tCHR tWTH VIH – VIL – tOFF DQ VOH – VOL – Open Note: OE, Address = "H" or "L" "H" or "L" 15/17 ¡ Semiconductor MSM518200 PACKAGE DIMENSIONS (Unit : mm) SOJ26/24-P-300-1.27 Mirror finish Package material Lead frame material Pin treatment Solder plate thickness Package weight (g) Epoxy resin 42 alloy Solder plating 5 mm or more 0.80 TYP. Notes for Mounting the Surface Mount Type Package The SOP, QFP, TSOP, SOJ, QFJ (PLCC), SHP and BGA are surface mount type packages, which are very susceptible to heat in reflow mounting and humidity absorbed in storage. Therefore, before you perform reflow mounting, contact Oki’s responsible sales person for the product name, package name, pin number, package code and desired mounting conditions (reflow method, temperature and times). 16/17 ¡ Semiconductor MSM518200 (Unit : mm) TSOPII26/24-P-300-1.27-K Mirror finish Package material Lead frame material Pin treatment Solder plate thickness Package weight (g) Epoxy resin 42 alloy Solder plating 5 mm or more 0.29 TYP. Notes for Mounting the Surface Mount Type Package The SOP, QFP, TSOP, SOJ, QFJ (PLCC), SHP and BGA are surface mount type packages, which are very susceptible to heat in reflow mounting and humidity absorbed in storage. Therefore, before you perform reflow mounting, contact Oki’s responsible sales person for the product name, package name, pin number, package code and desired mounting conditions (reflow method, temperature and times). 17/17