Chip Resistor Networks MNR Series < Automotive > Features 1) Can be mounted even more densely than chip resistors. 2) Mounting cost can be reduced by less frequency of mounting times. 3) Convex electrodes secures visual inspection of fillets after soldering. 4) ROHM resistors have obtained ISO9001 / ISO / TS16949 certification. 5) "Automotive" product is AEC-Q200 compliant. Size Type Code (mm) (inch) No. of terminals MNR02 1005 × 2 0402 × 2 4 2 MRAP M0AP MNR04 1005 × 4 0402 × 4 8 4 MRAP M0AP MNR12 1608 × 2 0603 × 2 4 2 ERAP E0AP MNR14 1608 × 4 0603 × 4 8 4 ERAP E0AP MNR15 1608 × 5 0603 × 5 10 8 ERRP E0RP MNR18 1605 × 8 0602 × 8 16 8 ERAP E0AP MNR32 3216 × 2 1206 × 2 4 2 J0AB MNR34 3216 × 4 1206 × 4 8 4 J5AB MNR35 3216 × 5 1206 × 5 10 8 J5R Part No. No. of elements GENERAL PURPOSE AUTOMOTIVE ∗Corresponds to AEC−Q200 Packing Specification Quantity / Reel Paper tape (2mm Pitch) 10,000 Paper tape (4mm Pitch) 5,000 Embossed tape (4mm Pitch) 4,000 ∗Please contact us for status of AEC-Q200 on "General purpose" products. Part Number Description M N R 0 2 Part No. Size (mm [inch]) MNR 02 (1005 [0402] × 2) 04 (1005 [0402] × 4) 12 (1608 [0603] × 2) 14 (1608 [0603] × 4) 15 (1608 [0603] × 5) 18 (1605 [0602] × 8) 32 (3216 [1206] × 2) 34 (3216 [1206] × 4) 35 (3216 [1206] × 5) (Chip Resistor Networks) www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ M 0 A P J 1 0 5 Type Code Resistance Tolerance Nominal Resistance F ( ±1% ) J ( ±5% )(Including jumper type) Resistance code, 3 or 4 digits. 000 denotes jumper type. Resistance tolerance F J Resistance code : : 4 digits 3 digits Ex.) 1Ω = 1R0 9.1 Ω = 9R1 10 Ω = 10R0 100 1M Ω = 1004 105 1/6 ( ±5% ) ( ±5% ) ( ±1% ) ( ±5% ) ( ±1% ) ( ±5% ) 2012.11 - Rev.B MNR series < Automotive > Data Sheet Products List Part No. MNR02 Type Code M0AP Rated Power (70°C) Limiting Element Voltage (W) (V) Maximum Overload Voltage (V) 0.063 / Element 25 − Temperature Resistance Coefficient Tolerance (ppm / °C) (%) ±200 J(±5%) Resistance Range Series 10Ω to 1MΩ E24 Operating Temperature Range (°C) Jumper type : Rmax = 50m Ω / Imax. = 1A (Element) +500/−250 MNR04 M0AP 0.063 / Element 1Ω to 9.1Ω E24 J(±5%) 50 25 ±200 10Ω to 1MΩ Jumper type : Rmax = 50m Ω / Imax. = 1A (Element) MNR12 E0AP 0.063 / Element −55 to +155 ±200 J(±5%) 10Ω to 1MΩ ±100 F(±1%) 10Ω to 1MΩ − 50 E24 Jumper type : Rmax = 50m Ω / Imax. = 1A (Element) ±500 MNR14 E0AP 0.063 / Element 2.2Ω to 6.8Ω E6 J(±5%) ±200 − 50 10Ω to 1MΩ E24 ±100 F(±1%) 10Ω to 1MΩ Jumper type : Rmax = 50m Ω / Imax. = 1A (Element) MNR15 E0RP MNR18 E0AP 0.031 / Element 12.5 − ±200 J(±5%) 56Ω to 100kΩ E24 0.063 / Element 25 − ±200 J(±5%) 10Ω to 1MΩ E24 Jumper type : Rmax = 50m Ω / Imax. = 1A (Element) MNR32 J0AB 0.125 / Element 200 ±200 400 10Ω to 1MΩ J(±5%) E24 −55 to +125 Jumper type : Rmax = 50m Ωx / Imax. = 2A (Element) MNR34 J5AB 0.125 / Element 200 ±200 400 J(±5%) 10Ω to 1MΩ E24 Jumper type : Rmax = 50m Ω / Imax. = 2A (Element) MNR35 J5R 0.063 / Element 50 ±200 100 J(±5%) 56Ω to 100kΩ E12 ∗Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. Circuit Construction MNR02 / 12 / 32 R1 R2 MNR04 / 14 / 34 R1 R2 R3 MNR15 / 35 R1=R2=R3=R4 www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ R2 R3 R6 R7 R8 R4 R1 R2 R3 R4 R5 R6 R7 R8 R4 R5 R1=R2 R1 MNR18 R1=R2=R3=R4=R5=R6=R7=R8 R1=R2=R3=R4=R5=R6=R7=R8 2/6 2012.11 - Rev.B MNR series < Automotive > Data Sheet Chip Resistor Dimensions and Markings MNR02 / 12 / 32 MNR04 / 14 / 34 b2 b2 MNR15 b1 L c c a p c a 103 a 103 W W W a a a p p b2 t b1 t L t L MNR18 MNR35 L <Marking method> There are three digits used for the calculation number according to IEC code and “R”is used for the decimal point. MNR35 is R + three digits used for the calculation number according to IEC code. L p p c a c a W R103 W a a b2 b1 b2 b1 t t (Unit : mm) Marking existence Part No. Type Code (mm) (inch) L W t a b1 b2 c p MNR02 M0AP 1005 × 2 0402 × 2 1.0±0.1 1.0±0.1 0.35±0.1 0.2±0.1 − 0.33 +0.1 0 0.25±0.1 0.68 No MNR04 M0AP 1005 × 4 0402 × 4 2.0±0.2 1.0±0.1 0.35±0.1 0.2±0.1 0.3±0.1 0.4±0.1 E0AP 1608 × 2 0603 × 2 1.6±0.1 1.6±0.1 0.5±0.1 0.3±0.2 MNR14 E0AP 1608 × 4 0603 × 4 3.2±0.1 1.6±0.1 0.5±0.1 0.3±0.2 MNR15 E0AP 1608 × 5 0603 × 5 3.2±0.1 1.6±0.1 0.5±0.1 0.3±0.1 0.32±0.15 0.48±0.15 MNR18 J5AB 1605 × 8 0602 × 8 3.8±0.1 1.6±0.1 0.45±0.1 0.3±0.2 0.3±0.1 MNR32 E0RP 3216 × 2 1206 × 2 2.6±0.2 3.1±0.2 0.55±0.1 0.5±0.3 MNR34 E0AP 3216 × 4 1206 × 4 5.2±0.4 3.1±0.2 0.55±0.1 J5R 3216 × 5 1206 × 5 6.4±0.4 3.1±0.2 0.55±0.1 MNR12 MNR35 ∗Including jumper type 0.25±0.1 0.5 No − 0.6±0.15 0.25±0.15 0.8 Yes 0.4±0.15 0.6±0.15 0.25±0.15 0.8 Yes 0.3±0.1 0.64 Yes 0.3±0.1 0.3±0.2 0.5 No − 1.0±0.2 0.5Max 1.27 Yes 0.5±0.3 0.8±0.2 1.0±0.2 0.5Max 1.27 Yes 0.5±0.3 0.8±0.2 1.0±0.2 0.5Max 1.27 Yes Land pattern Example MNR02 / 12 / 32 Land MNR04 / 14 / 34 MNR15 / 35 MNR18 E C C A D A D C C B P2 P1 C C A D A D C C B E P1 B B P2 P2 P1 P1 P2 P1 B P1 (Unit : mm) Dimensions Type Code A B C D MNR02 M0AP 0.5 0.35 to 0.4 0.5 MNR04 M0AP 0.5 0.4 0.5 MNR12 E0AP 1.0 0.4 to 0.6 0.7 to 0.8 MNR14 E0AP 1.0 0.4 to 0.6 0.7 to 0.8 MNR15 E0RP 1.0 0.48 MNR18 E0AP 1.0 MNR32 J0AB 2.1 MNR34 J5AB 2.1 MNR35 J5R 2.1 Part No. E P1 1.5 − 0.65 to 0.7 − 1.5 0.3 0.5 0.5 to 0.55 2.4 to 2.6 − 0.8 to 1.0 − 2.4 to 2.6 0.4 0.8 0.8 to 0.9 0.7 to 0.8 2.4 to 2.6 0.32 0.64 0.72 0.3 0.7 to 0.8 2.4 to 2.6 − 0.5 − 0.8 to 1.0 0.8 to 1.0 3.7 to 4.1 − 1.27 to 1.6 − 0.8 to 1.0 0.8 to 1.0 3.7 to 4.1 0.7 to 0.8 1.27 to 1.35 1.27 to 1.45 0.8 to 1.0 0.8 to 1.0 3.7 to 4.1 0.7 to 0.8 1.27 to 1.3 1.27 to 1.4 www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ 3/6 P2 2012.11 - Rev.B MNR series < Automotive > Data Sheet Derating Curve When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below. MNR02 / 04 / 12 / 14 80 60 40 20 0 MNR15 / 18 / 32 / 34 / 35 100 PERCENT RATED POWER (%) PERCENT RATED POWER (%) 100 −55 0 70 100 80 60 40 20 0 155 −55 0 70 100 125 AMBIENT TEMPERATURE (°C) AMBIENT TEMPERATURE (°C) Characteristics Guaranteed Value Resistor Type Jumper Type Test Items Test Conditions Resistance See "Products List" 20°C Variation of resistance with temperature See "Products List" Measurement : +20 / −55 / +20 / +125°C ± (2.0%+0.1Ω) Overload Rated voltage (current) ×2.5, 2s. Maximum overload voltage Max. 50mΩ Rosin·Ethanol : 25% (weight) Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. Solderability ± (1.0%+0.05Ω) ± (1.0%+0.1Ω)※MNR35 Resistance to soldering heat Max. 50mΩ No remarkable abnormality on the appearance. Soldering condition : 260±5°C Duration of immersion : 10±1s Rapid change of temperature ± (1.0%+0.05Ω) ± (1.0%+0.1Ω)※MNR35 Max. 50mΩ Test temp. : −55°C to +125°C 5cycle Damp heat, steady state ± (3.0%+0.1Ω) Max. 100mΩ 40°C, 93%RH (Relative Humidity) Test time : 1,000h to 1,048h Endurance at 70°C ± (3.0%+0.1Ω) Max. 100mΩ 70°C Rated voltage (current) 1.5h : ON − 0.5h : OFF Test time : 1,000h to 1,048h Endurance ± (3.0%+0.1Ω) Max. 100mΩ 125°C (MNR15 / 18 / 32 / 34 / 35) 155°C (MNR02 / 04 / 12 / 14) Test time : 1,000h to 1,048h Resistance to solvent ± (1.0%+0.05Ω) ± (1.0%+0.1Ω)※MNR35 Max. 50mΩ 23±5°C, Immersion cleaning, 5±0.5min Solvent : 2−propanol ± (1.0%+0.05Ω) Max. 50mΩ Bend strength of the end face plating − Without mechanical damage such as breaks. Compliance Standard(s) : IEC60115−8 JISC 5201−8 Chip weight (typical value) Parameter Unit MNR02 M0AP MNR04 M0AP MNR12 E0AP MNR14 E0AP MNR15 E0RP MNR18 E0AP MNR32 J0AB MNR34 J5AB MNR35 J5R Weight mg/pc 1.04 2.22 4.04 7.55 7.41 8.90 15.9 31.2 38.4 www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ 4/6 2012.11 - Rev.B MNR series < Automotive > Data Sheet Tape Dimensions (Unit : mm) Paper Tape P0 P2 P1 φD0 E F Part No. Type Code W F E A0 B0 MNR02 M0AP 8.0±0.3 3.5±0.05 1.75±0.1 1.17±0.1 1.17±0.1 MNR04 M0AP 8.0±0.3 3.5±0.05 1.75±0.1 1.2±0.1 2.2±0.1 MNR12 E0AP 8.0±0.3 3.5±0.05 1.75±0.1 1.8±0.1 1.8±0.1 MNR14 E0AP 8.0±0.3 3.5±0.05 1.75±0.1 1.8±0.1 3.4±0.1 MNR15 E0RP 8.0±0.3 3.5±0.05 1.75±0.1 1.8±0.1 3.4±0.1 MNR18 E0AP 8.0±0.3 3.5±0.05 1.75±0.1 1.95±0.15 4.1±0.15 Part No. Type Code D0 P0 P1 P2 T2 MNR02 M0AP +0.1 φ1.5 0 4.0±0.1 2.0±0.1 2.0±0.05 Max 0.5 MNR04 M0AP φ1.5 +0.1 0 4.0±0.1 2.0±0.1 2.0±0.05 Max 1.1 MNR12 E0AP φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 MNR14 E0AP φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 MNR15 E0RP φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 MNR18 E0AP φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 Max 1.1 Part No. Type Code W F E A0 B0 MNR32 J0AB 8.0±0.3 3.5±0.05 1.75±0.1 3.0±0.1 3.5±0.1 MNR34 J5AB 12.0±0.3 5.5±0.05 1.75±0.1 3.4±0.1 5.6±0.1 MNR35 J5R 12.0±0.3 5.5±0.05 1.75±0.1 3.4±0.1 6.6±0.1 Part No. Type Code D0 P0 P1 P2 K MNR32 J0AB φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 0.9±0.1 MNR34 J5AB φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 1.0±0.15 MNR35 J5R φ1.5 +0.1 0 4.0±0.1 4.0±0.1 2.0±0.05 1.0±0.15 W B0 A0 Top tape (Bottom tape) Base paper Cavity Components T2 (Unit : mm) Embossed Tape P2 E B0 W F φD 0 P0 A0 P1 www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ K 5/6 2012.11 - Rev.B MNR series < Automotive > Data Sheet Reel Dimensions Using two kinds of reels for taping. (MNR34/35 applies Fig. 1 only.) 02 04 06 08 06 D 04 B 02 A 08 Fig.1 C Label According to EIAJ ET-7200B (RRM) Fig.2 A B D C Label According to EIAJ ET-7200B (RRV) (Unit : mm) Part No. Type Code MNR02 M0AP MNR04 M0AP MNR12 E0AP MNR14 E0AP MNR15 E0RP MNR18 E0AP MNR32 J0AB MNR34 J5AB MNR35 J5R www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. ○ A B 0 φ180 −1.5 +1.0 φ60 0 C 9 +1.0 0 φ13±0.2 13 6/6 D +1.0 0 2012.11 - Rev.B Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. R1120A