6235 POWER INDUCTORS High-Reliability Power Inductors MS512PJB ■ High temperature materials allow operation in ambient temperatures up to 155°C. ■ Special construction allows it to pass vibration testing to 80 G and shock testing to 1000 G. ■ Tin-lead (Sn-Pb) termination for the best possible board adhesion Core material Ferrite Terminations Tin-lead (63/37) over tin over nickel. Weight 460 – 480 mg Ambient temperature –55°C to +105°C with Irms current, +105°C to +155°C with derated current Storage temperature Component: –55°C to +155°C. Tape and reel packaging: –55°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Enhanced crush-resistant packaging 350/7″reel Plastic tape: 12 mm wide, 0.3 mm thick, 8 mm pocket spacing, 3.68 mm pocket depth Recommended pick and place nozzle OD: 6.2 mm; ID: ≤ 3.1 mm DCR3 Inductance2 max Part number1 ±20% (µH) (Ohms) MS512PJB682MSZ 6.8 0.075 MS512PJB822MSZ 8.2 0.095 MS512PJB103MSZ 10.0 0.100 MS512PJB123MSZ 12.0 0.110 MS512PJB153MSZ 15.0 0.125 MS512PJB183MSZ 18.0 0.140 MS512PJB223MSZ 22.0 0.145 MS512PJB333MSZ 33.0 0.180 MS512PJB473MSZ 47.0 0.245 MS512PJB563MSZ 56.0 0.280 MS512PJB683MSZ 68.0 0.345 MS512PJB823MSZ 82.0 0.315 MS512PJB104MSZ 100.0 0.375 MS512PJB124MSZ 120.0 0.435 MS512PJB154MSZ 150.0 0.535 MS512PJB224MSZ 220.0 0.720 MS512PJB334MSZ 330.0 1.02 MS512PJB474MSZ 470.0 1.58 MS512PJB564MSZ 560.0 1.75 MS512PJB684MSZ 680.0 1.97 MS512PJB824MSZ 820.0 2.70 MS512PJB105MSZ 1000.0 3.20 MS512PJB155MSZ 1500.0 4.60 MS512PJB185MSZ 1800.0 5.42 MS512PJB225MSZ 2200.0 6.40 MS512PJB335MSZ 3300.0 8.90 MS512PJB475MSZ 4700.0 14.0 MS512PJB565MSZ 5600.0 16.4 MS512PJB685MSZ 6800.0 21.4 MS512PJB825MSZ 8200.0 24.0 MS512PJB106MSZ 10000.0 29.0 ® SRF (MHz)4 min typ 39 55 34 48 26 37 20 29 18 25 17 24 17 24 11 16 9.0 13 8.4 12 7.6 10.8 7.0 10.0 6.3 9.0 5.8 8.3 5.1 7.3 4.0 5.6 3.0 4.4 2.5 3.6 2.2 3.1 2.0 2.8 1.8 2.5 1.5 2.2 1.3 1.9 1.2 1.7 1.0 1.5 0.8 1.1 0.66 0.94 0.6 0.86 0.56 0.80 0.49 0.70 0.43 0.61 10% drop 2.6 2.5 2.3 1.9 1.9 1.7 1.6 1.3 1.1 1.0 0.90 0.46 0.46 0.44 0.37 0.31 0.26 0.22 0.20 0.17 0.16 0.14 0.12 0.11 0.090 0.080 0.070 0.070 0.070 0.062 0.059 Isat (A)5 Irms (A)6 20% 30% 20°C 40°C drop drop rise rise 2.7 2.8 1.0 1.5 2.6 2.7 1.0 1.5 2.4 2.5 1.0 1.4 2.2 2.3 1.0 1.4 2.0 2.0 0.97 1.4 1.8 1.9 0.96 1.3 1.7 1.7 0.88 1.3 1.4 1.5 0.80 1.0 1.2 1.2 0.64 0.92 1.0 1.1 0.60 0.86 0.94 0.96 0.58 0.80 0.52 0.55 0.58 0.76 0.52 0.54 0.56 0.72 0.48 0.51 0.48 0.64 0.43 0.45 0.42 0.58 0.36 0.37 0.36 0.51 0.29 0.30 0.32 0.44 0.25 0.26 0.29 0.40 0.22 0.23 0.26 0.37 0.19 0.21 0.22 0.32 0.18 0.19 0.21 0.26 0.17 0.18 0.19 0.24 0.13 0.14 0.15 0.21 0.12 0.13 0.14 0.18 0.11 0.11 0.13 0.18 0.090 0.10 0.11 0.14 0.077 0.084 0.095 0.12 0.080 0.085 0.080 0.10 0.075 0.080 0.070 0.095 0.070 0.078 0.065 0.090 0.067 0.074 0.060 0.075 MS512PJB106MSZ Testing: Z = COTS H = Screening per Coilcraft CP-SA-10001 N = Screening per Coilcraft CP-SA-10004 2. Inductance tested at 100 kHz, 0.1 Vrms using an Agilent/HP 4192A. 3. DCR measured on a micro-ohmmeter. 4. SRF measured using an Agilent/HP 8753ES or equivalent. 5. Typical DC current that causes the specified inductance drop from its value without current. 6. Typical current that causes the specified temperature rise from 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Specifications subject to change without notice. Please check our website for latest information. Document MS587-1 1102 Silver Lake Road Cary IL 60013 © Coilcraft, Inc. 2011 1. When ordering, please specify testing code: Phone 800-981-0363 Fax 847-639-1508 Revised 03/25/11b E-mail [email protected] Web www.coilcraft-cps.com 6235 POWER INDUCTORS MS512PJB Series (6235) Typical L vs Current Typical L vs Frequency 10000 10000 3300 µH 1000 µH 330 µH 100 µH 100 33 µH 10 µH 10 1 0.01 1000 µH 1000 Inductance (µH) 1000 Inductance (µH) 3300 µH 0.1 330 µH 100 µH 100 33 µH 10 µH 10 1 Current (A) 10 1 0.01 1 0.1 10 Frequency (MHz) Typical Current Derating 0.236 ±0.003* 6,00 ±0,076 120 100 90 0.236 ±0.003* 6,00 ±0,076 80 70 60 0.138 ±0.004 † 3,5 ±0,10 50 40 Recommended Land Pattern 25°C Percent of rated current 110 30 20 0.079 2,00 Isat Irms 10 0 -55 -40 -20 0 20 40 60 80 100 120 140 160 0.165 4,20 0.039 typ 1,00 Ambient temperature (°C) 0.260 0.167 6,60 4,25 0.165 4,20 0.071 1,80 0.079 2,00 0.167 4,25 0.260 6,60 0.039 typ 1,00 are of the case not * Dimensions including the termination. For maximum overall dimensions including the termination, add 0.005 in / 0,13 mm. † Height dimension is after mounting. For maximum height dimension before mounting, add 0.006 in / 0,152 mm. Dimensions are in ® Specifications subject to change without notice. Please check our website for latest information. 1102 Silver Lake Road Cary IL 60013 © Coilcraft, Inc. 2011 inches mm Document MS587-2 Phone 800-981-0363 Fax 847-639-1508 Revised 03/25/11 E-mail [email protected] Web www.coilcraft-cps.com