Toggles Series FP01 Rockers Distinctive Characteristics Pushbuttons Brilliant illumination for highly visible status indication with LEDs and caps in red, green, or amber; subdued illumination for low light requirements with white cap over red, green, or amber LEDs. D Keylocks Snap-in mounting for easy installation. Connector socket with 6 pins for simple connection. Tactiles Rugged construction and smooth actuation allow repeated, rapid actuation force anywhere on cap surface. Rotaries Photo interrupter, rather than contacts, ensures high reliability and long life of 3 million operations minimum. Slides Programmable Illuminated PB Contactless Pushbuttons Touch Tilt Well suited for gaming and vending machines, as well as equipment exposed to corrosive gases used in environments such as chemical or steel manufacturing plants. Accessories Indicators Actual Size Supplement FP01-15 D4 www.nkk.com Series FP01 Toggles Contactless Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE Photo Transistor 1 A C1 C F LEDs Receptacle Shape Single F C1 Round 6-pin Socket See Connector. Photo Interrupter 5 Unshaded A (Shaded) C Red D Amber F Green Actuator Colors Housing Black (Momentary Operating Function) B White C Red D Amber F Green Rockers C Pushbuttons 5 D Connector Assembled Connector with Wire Leads C2 * C3 Unassembled Connector and Pins No Code No Connector * Available in Americas only DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Programmable Illuminated PB 1 Keylocks FP01 Contact factory for custom options Rotaries FP0115CAC1FF Green Actuator with Green LED Slides Single Photo Transistor with Normally Unshaded Photo Interrupter Tactiles Round, Black Housing ACTUATOR & INTERRUPTER Single Photo Transistor 5 Shaded When shaded, the photo transistor momentarily activates electrical function which signals the external device to change its state. HOUSING SHAPE & COLOR C Round Shape A Black Housing Tilt LED connector pins are 5 & 6; interrupter connector pins are 3-4 & 1-2. Normally Unshaded with Momentary Shaded status 6 5 4 3 2 1 Touch FP0115 Unshaded Indicators 1 Down Schematics RECEPTACLE C1 Accessories Normal Model Photo Interrupter 6-pin Socket Supplement Actuator Position 6 5 4 3 2 1 www.nkk.com D5 Series FP01 Toggles Contactless Pushbuttons SWITCH SPECIFICATIONS Rockers Status of Photo Interrupter: Collector Current IC: Status of Photo Transistor: Actuator Down Unshaded Shaded 0.8mA minimum 10µA maximum On Off IF = 20mA & VCE = 5V MECHANICAL SPECIFICATIONS Total Travel: Operating Force: D Mechanical Life: Operating Temperature Range: .079” (2.0mm) 0.75 N (.169 lbf) 3,000,000 operations minimum –25°C through +50°C (–13°F through +122°F) MATERIALS Actuator: Polyacetal Housing: Polyamide PHOTO INTERRUPTER SPECIFICATIONS Keylocks Programmable Illuminated PB Pushbuttons Output Condition of Photo Transistor: Actuator Up Electrical & Optical Characteristics (Temperature @ 25°C) Typical Maximum Condition 1.3V 1.6V IF = 50mA Reverse Current IR: 10µA FR = 5V Collector-Emitter Saturation Voltage VCE sat: 0.4V IF = 20mA & IC = 0.1mA Input Rotaries Forward Voltage VF: Transmission Slides Absolute Maximum Ratings Input LED Output Photo Transistor Forward Current IF: Tactiles Reverse Voltage VR: Power Dissipation PD: 50mA Collector-Emitter Voltage VCEO: 30V 5V Emitter-Collector Voltage VECO: 4.5V Collector Current IC: 80mW 30mA Collector Dissipation PC: Tilt Circuit Design Considerations 180 Output of the infrared LED in the photo interrupter decreases approximately 50% after 100,000 hours. RL VOUT Recommended load resistance (RL) is 40k ~ 120kΩ for the illustrated circuit. Touch 80mW VCC = 5V Threshold Voltage VHI : 3.8V VLO : 1.0V GND LED COLORS & SPECIFICATIONS Accessories Indicators LEDs are an integral part of the switch and not available separately. The electrical specifications shown are determined at a basic temperature of 25°C. Supplement If the source voltage exceeds the rated voltage, a ballast resistor is required. D6 R + IF Anode VF E Cathode – R = Where: R = E = VF = IF = E – VF IF Resistor Value (Ohms) Source Voltage (V) Forward Voltage (V) Forward Current (A) C D F Color Red Amber Green Forward Peak Current I FM 30mA 25mA 25mA Continuous Forward Current IF 20mA 20mA 20mA Single Element LED Forward Voltage VF 1.85V 2.0V 2.25V Reverse Peak Voltage VRM 5V 5V 5V Current Reduction Rate Above 25°C ∆I F 0.38mA /°C 0.28mA /°C 0.40mA /°C Ambient Temperature Range www.nkk.com –25° ~ +50°C Series FP01 Toggles Contactless Pushbuttons ACTUATOR COLORS D Red F Amber Green Rockers C White CONNECTOR OPTIONS C3 Connector body: JST model ZHR-6 Crimp connector pins: JST model SZH-002T-P0.5 Wire leads: 28-26AWG; 12-inch, unstripped; Blue for Pin 1 AT022 Unassembled Connector and Pins No Code 1 connector and 8 crimp connector pins only (no wire leads provided). Matching wire leads: 28-26AWG Pushbuttons AT021 Assembled Connector with Wire Leads No Connector Recommended connector for assembly: JST model number ZHR-6 D Keylocks Recommended crimp connector pins: JST model SZH-002T-P0.5 for 28-26AWG wire leads or SZH-003T-P0.5 for 32-28AWG wire leads. (5.0) .197 NKK P/N This Side Rotaries TYPICAL SWITCH DIMENSIONS Pin 1 (1.1)R Typ .043 Tactiles (5.3) .209 (21.4) .843 (2.3) .091 (22.8) Dia .898 6 5 4 3 2 1 Terminal Connector Detail Recommended Panel Thickness Range: .098” ~ .197” (2.5mm ~ 5.0mm) Tilt (22.9) Dia .902 (1.5) .059 (19.6) Dia .772 (26.0) Dia 1.024 Slides (25.1) .988 FP0115CAC1FF Touch LEGENDS Indicators NKK Switches can provide custom legends for caps. Contact factory for more information. Suggested Printable Area for FP01 Cap Accessories T ER AL Recommended Methods: Screen Print on cap. Epoxy based ink is recommended. (16.56) Dia .475 (19.6) Dia .772 (1.52) Typ .060 Supplement C2 Programmable Illuminated PB B Shaded area is printable area. www.nkk.com D7