BA - SIL Series 0.5 to 1 Watt Isolated DC-DC Converter Single Output 1. Features : ! 4 Pin SIL Package ! Low Ripple and Noise ! Input / Output Isolation 1000 Vdc ! 100 % Burn-In ! Input Filter with Internal Capacitor ! Custom Design Available 2. Absolute maximum ratings： ： ( Exceeding these values may damage the module. These are not continuous operating ratings ) Parameter Condition Min. Typ. Max. 5V Input Model -0.7 5 7.5 12V Input Model -0.7 12 15 24V Input Model -0.7 24 30 Max. Output power --- --- 1.0 W Output Short circuit duration --- --- 1.0 Second -40 --- +85 -55 --- +105 Input Absolute Voltage Range Operating temperature Output Full Load Storage temperature Unit Vdc ℃ 3. Nominal Input / Output Electrical Specifications : ( Specifications typical at Ta = +25℃, nominal input voltage, rated output current unless otherwise noted ) Parameter Condition Min. Typ. Max. 5V Input Model 4.5 5 5.5 12V Input Model 10.8 12 13.2 24V Input Model 21.6 24 26.4 Output Voltage Accuracy --- --- ± 5.0 Voltage Balance (Dual Outputs ) --- --- ± 1.0 Switching Frequency --- 100 --- KHz Temperature Coefficient --- ± 0.01 ± 0.02 %/ ℃ 60 Seconds / 0.5mA 1000 --- --- Vdc 500 Vdc 1000 --- --- MΩ 1 KHz / 250 mV rms --- 40 --- pF --- --- 1.3 % Input Voltage Range Unit Vdc % Nominal Input Isolation Voltage Isolation Resistance Isolation Capacitance Max. Line Regulation (Per 1.0 % change in input change) BOTHHAND USA. http://www.bothhand.com BA - SIL Series 0.5 to 1 Watt Isolated DC-DC Converter Single Output 4. Single Output Selection Guide： ： ( Specifications typical at Ta = +25 ℃, Nominal input voltage, Rated output current unless otherwise noted ) Input Output Output Input Current Input Current Output Load Voltage Voltage Current @ No Load @ Max. Load Ripple Regulation (Vdc) (Vdc) (mA) Max (mA) Typ. (mA) Typ. (mV) Max. (%) Max. 3.3 150 28 133 60 ± 12 74 5.0 100 28 135 60 ± 10 74 12.0 42 28 133 100 ±8 76 5.0 100 18 56 60 ±8 74 12.0 42 18 55 100 ±8 76 5.0 100 5 29 60 ±8 72 3.3 300 30 267 60 ± 10 74 5.0 200 30 253 60 ±8 79 12.0 100 30 307 100 ±8 78 5.0 200 14 105 60 ±8 79 12.0 83 14 105 100 ±8 79 5.0 200 5 54 60 ±8 77 Bothhand Efficiency Model No. (%) Typ. 0.5 W Single Output Series： BA-053R3S BA-0505S 5 BA-0512S BA-1205S 12 BA-1212S BA-2405S 24 1.0 W Single Output Series： BA-053R3S1 BA-0505S1 5 BA-0512S1 BA-1205S1 12 BA-1212S1 BA-2405S1 24 BA-xxxxS1 Notes： 1. Standard output voltage is 3.3V, 5V, 9V, 12V, 15V, BA-xxxxS1 is for Customer Design. 2. Load regulation is for Each output current change from 20 % to 100 % Max. Load. Mechanical Dimension： Dimension： Units : mm ( inch ) Pin 1K Vdc - Single 1 -Vin 2 +Vin 3 Vo (-) 4 Vo (+) Note：” --- “ means Omitted Tolerance : .xx ± 0.25 ( ± 0.01 ) BOTHHAND USA. http://www.bothhand.com