HD74ALVCH16825 18-bit Buffers / Drivers with 3-state Outputs ADE-205-172A (Z) 2nd. Edition December 1999 Description The HD74ALVCH16825 improves the performance and density of 3-state memory address drivers, clock drivers, and bus-oriented receivers and transmitters. The device can be used as two 9-bit buffers or one 18bit buffer. It provides true data. The 3-state control gate is a 2-input AND gate with active low inputs so that if either output enable (OE1 or OE2) input is high, all nine affected outputs are in the high impedance state. Active bus hold circuitry is provided to hold unused or floating data inputs at a valid logic level. Features • VCC = 2.3 V to 3.6 V • Typical VOL ground bounce < 0.8 V (@VCC = 3.3 V, Ta = 25°C) • Typical VOH undershoot > 2.0 V (@VCC = 3.3 V, Ta = 25°C) • High output current ±24 mA (@V CC = 3.0 V) • Bus hold on data inputs eliminates the need for external pullup / pulldown resistors Function Table Inputs Output Y OE1 OE2 A L L L L L L H H H X X Z X H X Z H : High level L : Low level X : Immaterial Z : High impedance HD74ALVCH16825 Pin Arrangement 56 1OE2 1OE1 1 1Y1 2 55 1A1 1Y2 3 54 1A2 GND 4 53 GND 1Y3 5 52 1A3 1Y4 6 VCC 7 51 1A4 1Y5 8 49 1A5 1Y6 9 48 1A6 1Y7 10 47 1A7 GND 11 46 GND 1Y8 12 45 1A8 1Y9 13 44 1A9 GND 14 43 GND GND 15 42 GND 2Y1 16 41 2A1 2Y2 17 40 2A2 GND 18 39 GND 2Y3 19 38 2A3 2Y4 20 37 2A4 2Y5 21 36 2A5 VCC 22 35 VCC 2Y6 23 34 2A6 50 VCC 2Y7 24 33 2A7 GND 25 32 GND 2Y8 26 31 2A8 2Y9 27 30 2A9 2OE1 28 29 2OE2 (Top view) 2 HD74ALVCH16825 Absolute Maximum Ratings Item Symbol Ratings Unit VCC –0.5 to 4.6 V VI –0.5 to 4.6 V VO –0.5 to VCC +0.5 V Input clamp current I IK –50 mA VI < 0 Output clamp current I OK ±50 mA VO < 0 or VO > VCC Continuous output current IO ±50 mA VO = 0 to VCC TSSOP Supply voltage Input voltage *1 Output voltage *1, 2 Conditions ±100 Maximum power dissipation at Ta = 55°C (in still air) *3 PT 1 W Storage temperature Tstg –65 to 150 °C Notes: Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. 1. The input and output negative voltage ratings may be exceeded if the input and output clamp current ratings are observed. 2. This value is limited to 4.6 V maximum. 3. The maximum package power dissipation is calculated using a junction temperature of 150°C and a board trace length of 750 mils. Recommended Operating Conditions Item Symbol Min Max Unit Supply voltage VCC 2.3 3.6 V Input voltage VI 0 VCC V Output voltage VO 0 VCC V High level output current I OH — –12 mA — –12 VCC = 2.7 V — –24 VCC = 3.0 V — 12 — 12 VCC = 2.7 V — 24 VCC = 3.0 V Low level output current I OL mA Input transition rise or fall rate ∆t / ∆v 0 10 ns / V Operating temperature Ta –40 85 °C Conditions VCC = 2.3 V VCC = 2.3 V Note: Unused control inputs must be held high or low to prevent them from floating. 3 HD74ALVCH16825 Logic Diagram 1OE1 1 1OE2 56 1A1 55 2 1Y1 To eight other channels 2OE1 28 2OE2 29 2A1 41 16 To eight other channels 4 2Y1 HD74ALVCH16825 Electrical Characteristics (Ta = –40 to 85°C) Item Symbol VCC (V) *1 Input voltage VIH VIL Output voltage VOH Min Max Unit 2.3 to 2.7 1.7 — V 2.7 to 3.6 2.0 — 2.3 to 2.7 — 0.7 2.7 to 3.6 — 0.8 I OH = –100 µA Min to Max VCC–0.2 — 2.3 2.0 — I OH = –6 mA, VIH = 1.7 V 2.3 1.7 — I OH = –12 mA, VIH = 1.7 V 2.7 2.2 — I OH = –12 mA, VIH = 2.0 V 3.0 2.4 — I OH = –12 mA, VIH = 2.0 V 3.0 2.0 — I OH = –24 mA, VIH = 2.0 V Min to Max — 0.2 I OL = 100 µA 2.3 — 0.4 I OL = 6 mA, VIL = 0.7 V 2.3 — 0.7 I OL = 12 mA, VIL = 0.7 V 2.7 — 0.4 I OL = 12 mA, VIL = 0.8 V 3.0 — 0.55 I OL = 24 mA, VIL = 0.8 V I IN 3.6 — ±5 I IN (hold) 2.3 45 — VIN = 0.7 V 2.3 –45 — VIN = 1.7 V 3.0 75 — VIN = 0.8 V 3.0 –75 — VIN = 2.0 V 3.6 — ±500 VIN = 0 to 3.6 V I OZ 3.6 — ±10 µA VOUT = VCC or GND Quiescent supply current I CC 3.6 — 40 µA VIN = VCC or GND 3.0 to 3.6 — 750 µA VIN = one input at (VCC–0.6) V, other inputs at V CC or GND VOL Input current Off state output current *2 ∆I CC V Test Conditions µA VIN = VCC or GND Notes: 1. For conditions shown as Min or Max, use the appropriate values under recommended operating conditions. 2. For I/O ports, the parameter I OZ includes the input leakage current. 5 HD74ALVCH16825 Switching Characteristics (Ta = –40 to 85°C) Item Symbol VCC (V) Min Typ Max Unit FROM (Input) TO (Output) Propagation delay time t PLH 2.5±0.2 1.0 — 4.1 ns A Y t PHL 2.7 — — 3.9 3.3±0.3 1.0 — 3.4 t ZH 2.5±0.2 1.0 — 6.0 ns OE Y t ZL 2.7 — — 5.7 3.3±0.3 1.0 — 4.7 t HZ 2.5±0.2 1.9 — 5.6 ns OE Y t LZ 2.7 — — 4.9 3.3±0.3 1.3 — 4.5 3.3 — 3.5 — pF Control inputs 3.3 — 6.0 — 3.3 — 7.5 — Output enable time Output disable time Input capacitance Output capacitance CIN CO Data inputs pF Outputs • Test Circuit See under table 500 Ω S1 OPEN GND *1 C L = 50 pF 500 Ω Load Circuit for Outputs Symbol t PLH / t PHL t su / t h / t w t ZH/ t HZ t ZL / t LZ Vcc=2.5±0.2V Vcc=2.7V, 3.3±0.3V OPEN OPEN GND GND 4.6 V 6.0 V Note: 1. C L includes probe and jig capacitance. 6 HD74ALVCH16825 • Waveforms – 1 tf tr 90 % Input VIH 90 % Vref Vref 10 % 10 % GND t PHL t PLH VOH Output Vref Vref VOL • Waveforms – 2 Output Control tf tr VIH 90 % 90 % Vref Vref 10 % t ZL 10 % GND t LZ ≈VOH1 Vref Waveform - A t ZH Waveform - B VOL + 0.3 V t HZ VOH – 0.3 V Vref VOL VOH ≈VOL1 TEST VIH Vref VOH1 VOL1 Vcc=2.5±0.2V Vcc=2.7V, 3.3±0.3V 2.3 V 2.7 V 1.2 V 2.3 V 1.5 V 3.0 V GND GND Notes: 1. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, Zo = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. 2. Waveform – A is for an output with internal conditions such that the output is low except when disabled by the output control. 3. Waveform – B is for an output with internal conditions such that the output is high except when disabled by the output control. 4. The output are measured one at a time with one transition per measurement. 7 HD74ALVCH16825 Package Dimensions Unit : mm +0.3 14.00 –0.1 29 6.10 +0.3 –0.1 56 0.20 +0.1 –0.05 0.50 28 0.08 M 0.15 ± 0.05 1 1.20 max 0.10 0.05 Min 0.40 Max 8.10 ± 0.3 10° Max 0.50 ± 0.1 Hitachi code EIAJ code JEDEC code 8 TTP-56D — — HD74ALVCH16825 Cautions 1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Hitachi bears no responsibility for problems that may arise with third party’s rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice. Confirm that you have received the latest product standards or specifications before final design, purchase or use. 3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However, contact Hitachi’s sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. 4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other consequential damage due to operation of the Hitachi product. 5. This product is not designed to be radiation resistant. 6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from Hitachi. 7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductor products. Hitachi, Ltd. Semiconductor & Integrated Circuits. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109 URL NorthAmerica : http:semiconductor.hitachi.com/ Europe : http://www.hitachi-eu.com/hel/ecg Asia (Singapore) : http://www.has.hitachi.com.sg/grp3/sicd/index.htm Asia (Taiwan) : http://www.hitachi.com.tw/E/Product/SICD_Frame.htm Asia (HongKong) : http://www.hitachi.com.hk/eng/bo/grp3/index.htm Japan : http://www.hitachi.co.jp/Sicd/index.htm For further information write to: Hitachi Semiconductor (America) Inc. 179 East Tasman Drive, San Jose,CA 95134 Tel: <1> (408) 433-1990 Fax: <1>(408) 433-0223 Hitachi Europe GmbH Electronic components Group Dornacher Stra§e 3 D-85622 Feldkirchen, Munich Germany Tel: <49> (89) 9 9180-0 Fax: <49> (89) 9 29 30 00 Hitachi Europe Ltd. Electronic Components Group. Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA, United Kingdom Tel: <44> (1628) 585000 Fax: <44> (1628) 778322 Hitachi Asia Pte. Ltd. 16 Collyer Quay #20-00 Hitachi Tower Singapore 049318 Tel: 535-2100 Fax: 535-1533 Hitachi Asia Ltd. Taipei Branch Office 3F, Hung Kuo Building. No.167, Tun-Hwa North Road, Taipei (105) Tel: <886> (2) 2718-3666 Fax: <886> (2) 2718-8180 Hitachi Asia (Hong Kong) Ltd. Group III (Electronic Components) 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: <852> (2) 735 9218 Fax: <852> (2) 730 0281 Telex: 40815 HITEC HX Copyright ' Hitachi, Ltd., 1999. All rights reserved. Printed in Japan. 9