LT3508 Dual Monolithic 1.4A Step-Down Switching Regulator DESCRIPTION FEATURES n n n n n n n n n n The LT®3508 is a dual current mode PWM step-down DC/DC converter with internal power switches capable of generating two 1.4A outputs. The wide input voltage range of 3.7V to 36V makes the LT3508 suitable for regulating power from a wide variety of sources, including automotive batteries, 24V industrial supplies and unregulated wall adapters. Both converters are synchronized to a single oscillator programmable up to 2.5MHz and run with opposite phases, reducing input ripple current. Its high operating frequency allows the use of small, low cost inductors and ceramic capacitors, resulting in low, predictable output ripple. Each regulator has independent tracking and softstart circuits and generates a power good signal when its output is in regulation, easing power supply sequencing and interfacing with microcontrollers and DSPs. Wide Input Voltage Range: 3.7V to 36V Two 1.4A Output Switching Regulators with Internal Power Switches Adjustable 250kHz to 2.5MHz Switching Frequency Synchronizable over the Full Frequency Range Anti-Phase Switching Reduces Ripple Uses Small Inductors and Ceramic Capacitors Accurate Programmable Undervoltage Lockout Independent Tracking, Soft-Start and Power Good Circuits Ease Supply Sequencing Output Adjustable Down to 800mV Small 4mm × 4mm 24-Pin QFN or 16-Pin Thermally Enhanced TSSOP Surface Mount Packages APPLICATIONS n n n n n Automotive DSP Power Supplies Wall Transformer Regulation DSL and Cable Modems PCI Express Cycle-by-cycle current limit, frequency foldback and thermal shutdown provide protection against shorted outputs, and soft-start eliminates input current surge during startup. The low current (<2μA) shutdown mode enables easy power management in battery-powered systems. , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION 3.3V and 5V Dual Output Step-Down Converter with Output Sequencing VIN 5.6V TO 36V ON OFF Efficiency 4.7μF VIN SHDN BOOST1 0.22μF 6.8μH 0.22μF SW1 35.7k 56.2k FB1 22μF 51k 150pF 1nF VOUT2 = 5V SW2 LT3508 11.5k VIN = 12V 90 10μH EFFICIENCY (%) OUT1 3.3V 1.4A 95 OUT2 5V 1.4A BOOST2 FB2 VC1 VC2 TRACK/SS1 TRACK/SS2 PG1 PG2 GND 43k RT/SYNC 52.3k fSW = 700kHz 10μF 10.7k 80 75 70 100k 65 100pF 3508 TA01a VOUT1 = 3.3V 85 POWER GOOD 0 0.5 1 LOAD CURRENT (A) 1.5 3508 TA01b 3508fb 1 LT3508 ABSOLUTE MAXIMUM RATINGS (Note 1) VIN Pin Voltage............................................(–0.3V), 40V BOOST Pin Voltage ...................................................60V BOOST Above SW Voltage ........................................30V SHDN, PG Voltage.....................................................40V TRACK/SS, FB, RT/SYNC, VC Voltage ..........................6V Operating Junction Temperature Range (Note 2) LT3508E ............................................. –40°C to 125°C LT3508I .............................................. –40°C to 125°C LT3508H ............................................ –40°C to 150°C Storage Temperature Range QFN.................................................... –65°C to 150°C TSSOP ............................................... –65°C to 150°C Lead Temperature (Soldering, 10 sec) TSSOP .............................................................. 300°C PIN CONFIGURATION VC2 PG2 RT/SYNC SHDN VC1 TOP VIEW PG1 TOP VIEW TRACK/SS1 1 16 FB1 BOOST1 2 15 VC1 SW1 3 14 PG1 VIN1 4 13 RT/SYNC GND 3 VIN2 5 12 SHDN GND 4 SW2 6 11 PG2 GND 5 14 GND BOOST2 7 10 VC2 GND 6 13 GND TRACK/SS2 8 9 18 FB2 FB1 1 17 TRACK/SS2 TRACK/SS1 2 SW2 9 10 11 12 VIN2 8 BOOST2 θJA = 40°C/W, θJC = 10°C/W EXPOSED PAD (PIN 17) IS GND AND MUST BE SOLDERED TO PCB 7 VIN1 FE PACKAGE 16-LEAD PLASTIC TSSOP 15 GND SW1 FB2 16 GND 25 BOOST1 17 24 23 22 21 20 19 UF PACKAGE 24-LEAD (4mm s 4mm) PLASTIC QFN θJA = 40°C/W, θJC = 10°C/W EXPOSED PAD (PIN 25) IS GND AND MUST BE SOLDERED TO PCB ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT3508EFE#PBF LT3508EFE#TRPBF 3508FE 16-Lead Plastic TSSOP –40°C to 125°C LT3508IFE#PBF LT3508IFE#TRPBF 3508FE 16-Lead Plastic TSSOP –40°C to 125°C LT3508HFE#PBF LT3508HFE#TRPBF 3508HFE 16-Lead Plastic TSSOP –40°C to 150°C LT3508EUF#PBF LT3508EUF#TRPBF 3508 24-Lead (4mm × 4mm) Plastic QFN –40°C to 125°C LT3508IUF#PBF LT3508IUF#TRPBF 3508 24-Lead (4mm × 4mm) Plastic QFN –40°C to 125°C LT3508HUF#PBF LT3508HUF#TRPBF 3508H 24-Lead (4mm × 4mm) Plastic QFN –40°C to 150°C Consult LTC Marketing for parts specified with wider operating temperature ranges.*Temperature grades are identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 3508fb 2 LT3508 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 12V, VBOOST = 17V unless otherwise noted. (Note 2) PARAMETER CONDITIONS MIN Minimum Operating Voltage, VIN1 Minimum Operating Voltage, VIN2 VIN1 = 12V TYP MAX l 3.4 3.7 UNITS V l 2.5 3.0 V VIN1 Quiescent Current Not Switching 4.3 5.2 mA VIN2 Quiescent Current Not Switching 320 500 μA Shutdown Current (VIN1 + VIN2) VSHDN = 0.3V FB Voltage l FB Pin Bias Current (Note 3) VFB = 0.800V, VC = 0.4V FB Voltage Line Regulation 5V < VIN < 40V 0.790 0.784 l 0.1 2 μA 0.800 0.814 0.816 V V 50 300 0.01 nA %/V Error Amp Transconductance 300 μS Error Amp Voltage Gain 600 V/V 2.5 A/V VC to Switch Current Gain Switching Frequency RT = 33.2k Switching Phase RT = 33.2k Maximum Duty Cycle (Note 4) RT = 33.2k RT = 7.50k RT = 169k Foldback Frequency RT = 33.2k, VFB = 0V Switch Current Limit (Note 5) Duty Cycle = 15% Switch VCESAT ISW = 1.5A l l l 0.92 1 1.06 MHz 150 180 210 Deg 84 90 80 98 % % % 120 kHz 2.0 2.6 3.2 300 A mV Switch Leakage Current 0.01 1 μA Minimum Boost Voltage 1.7 2.5 V Boost Pin Current ISW = 1.5A TRACK/SS Pin Current VTRACK/SS = 0V 0.8 56 35 50 mA 1.2 2.2 μA PG Threshold Offset VFB Rising 75 110 mV PG Voltage Output Low VFB = 0.6V, IPG = 250μA 0.13 0.4 V PG Pin Leakage VPG = 2V 0.01 1 μA 2.53 2.63 2.73 V 6 8 10 μA SHDN Threshold Voltage SHDN Input Current (Note 6) VSHDN = 60mV Above Threshold Voltage SHDN Threshold Current Hysteresis SYNC Threshold Voltage SYNC Input Frequency Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LT3508E is guaranteed to meet performance specifications from 0°C to 125°C junction temperature. Specifications over the –40°C to 125°C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LT3508I is guaranteed over the full –40°C to 125°C operating junction temperature range. The LT3508H is guaranteed over the full –40°C to 150°C operating junction temperature range. High junction temperatures degrade operating lifetimes. Operating lifetime is derated at junction temperatures greater than 125°C. 5.5 7.5 9.5 μA 1 1.25 1.5 V 2.5 MHz 0.25 Note 3: Current flows out of pin. Note 4: VBOOST =12V. Circuitry increases the maximum duty cycle of the LT3508 when VBOOST > VIN + 2.5V. See “Minimum Operating Voltage” in the Applications Information section for details. Note 5: Current limit is guaranteed by design and/or correlation to static test. Slope compensation reduces current limit at higher duty cycles. Note 6: Current flows into pin. Note 7: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed the maximum operating junction temperature range when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability. 3508fb 3 LT3508 TYPICAL PERFORMANCE CHARACTERISTICS Efficiency, VOUT = 3.3V Efficiency, VOUT = 5V TA = 25°C f = 700kHz TA = 25°C f = 700kHz 85 VIN = 24V EFFICIENCY (%) EFFICIENCY (%) 85 VIN = 32V 80 75 70 85 VIN = 12V VIN = 24V 80 75 VIN = 32V 70 65 60 0 0.5 1 LOAD CURRENT (A) 1.5 TA = 25°C f = 1MHz 80 VIN = 3.3V 75 VIN = 5V 70 VIN = 12V 65 60 0 0.5 1 LOAD CURRENT (A) 3508 G01 55 1.5 0 1.5 0.5 1 LOAD CURRENT (A) 3508 G02 3508 G03 Switch Current Limit vs Temperature Feedback Voltage 0.810 Switch Current Limit vs Duty Cycle 3.0 3.0 2.5 2.5 TA = 25°C TYPICAL 0.800 CURRENT LIMIT (A) 0.805 CURRENT LIMIT (A) FEEDBACK VOLTAGE (V) EFFICIENCY (%) VIN = 12V 90 65 Efficiency, VOUT = 1.8V 90 95 2.0 1.5 1.0 2.0 MINIMUM 1.5 1.0 0.795 0.5 0.790 –50 –25 0 0.5 0 –50 –25 25 50 75 100 125 150 TEMPERATURE (°C) 0 0 1.2 RT (kΩ) 1 0.1 1 FREQUENCY (MHz) 10 3508 G07 3.0 RT = 33.2k 1.0 0.8 0.6 0.4 0.2 0 –50 –25 0 100 80 Switching Frequency Foldback SWITCHING FREQUENCY (MHz) SWITCHING FREQUENCY (MHz) TA = 25°C 10 40 60 DUTY CYCLE (%) 3508 G06 Switching Frequency vs Temperature Switching Frequency vs RT 100 20 3508 G05 3508 G04 1000 0 25 50 75 100 125 150 TEMPERATURE (°C) 25 50 75 100 125 150 TEMPERATURE (°C) 3508 G08 TA = 25°C 2.5 RT = 7.50k 2.0 1.5 1.0 RT = 33.2k 0.5 RT = 169k 0 0 100 200 300 400 500 600 700 800 FEEDBACK VOLTAGE (mV) 3508 G09 3508fb 4 LT3508 TYPICAL PERFORMANCE CHARACTERISTICS Quiescent Current 5.0 VC Voltages TA = 25°C 4.5 VIN1 30 2.0 CLAMP VOLTAGE OUTPUT CURRENT (μA) 4.0 VC VOLTAGE (V) 3.5 3.0 2.5 2.0 1.5 1.0 TO SWITCH 1.5 1.0 0.5 0 15 20 25 30 INPUT VOLTAGE (V) 35 0 –50 –25 40 0 3508 G10 15 SOURCING 10 0 25 50 75 100 125 150 TEMPERATURE (°C) 3508 G12 3508 G11 Switch Voltage Drop 350 20 0 –50 –25 25 50 75 100 125 150 TEMPERATURE (°C) Boost Pin Current 35 TA = 25°C TA = 25°C 30 300 BOOST PIN CURRENT (mA) 10 250 200 150 100 25 20 15 10 5 50 0 0 1 0.5 SWITCH CURRENT (A) 0 1 0.5 SWITCH CURRENT (A) 0 1.5 1.5 3508 G14 3508 G13 SHDN Pin Current Undervoltage Lockout 4.0 120 TA = –45°C 100 VIN1 3.5 3.0 TA = 125°C INPUT VOLTAGE (V) 5 SWITCH VOLTAGE (mV) 0 SINKING 25 5 VIN2 0.5 SHDN PIN CURRENT (μA) INPUT CURRENT (mA) Error Amp Output Current 35 2.5 80 TA = 25°C 60 40 VIN2 2.5 2.0 1.5 1.0 20 0.5 0 0 5 10 15 20 25 30 SHDN PIN VOLTAGE (V) 35 40 3508 G15 0 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 3508 G16 3508fb 5 LT3508 PIN FUNCTIONS BOOST1, BOOST2: The BOOST pins are used to provide drive voltages, higher than the input voltage, to the internal NPN power switches. Tie through a diode to a 2.8V or higher supply, such as VOUT or VIN. Exposed Pad: The Exposed Pad metal of the package provides both electrical contact to ground and good thermal contact to the printed circuit board. The Exposed Pad must be soldered to the circuit board for proper operation. FB1, FB2: The LT3508 regulates each feedback pin to 0.800V. Connect the feedback resistor divider taps to these pins. GND: Tie the GND pins directly to the Exposed Pad and ground plane. PG1, PG2: The power good pins are the open-collector outputs of an internal comparator. PG remains low until the FB pin is within 10% of the final regulation voltage. As well as indicating output regulation, the PG pins can be used to sequence the two switching regulators. These pins can be left unconnected. The PG outputs are valid when VIN1 is greater than 2.4V and SHDN is high. The PG comparators are disabled in shutdown. RT/SYNC: The RT/SYNC pin is used to set the internal oscillator frequency. Tie a 33.2k resistor from RT/SYNC to GND for a 1MHz switching frequency. To synchronize the part to an external frequency, drive the RT/SYNC pin with a logic-level signal with positive and negative pulse widths of at least 80ns. SHDN: The shutdown pin is used to put the LT3508 in shutdown mode. Pull the pin below 0.3V to shut down the LT3508. The 2.63V threshold can function as an accurate undervoltage lockout (UVLO), preventing the regulator from operating until the input voltage has reached the programmed level. Do not drive SHDN more than 6V above VIN1. SW1, SW2: The SW pins are the outputs of the internal power switches. Connect these pins to the inductors, catch diodes and boost capacitors. TRACK/SS1, TRACK/SS2: The TRACK/SS pins are used to soft-start the two channels, to allow one channel to track the other output, or to allow both channels to track another output. For tracking, tie a resistor divider to this pin from the tracked output. For soft-start, tie a capacitor to this pin. An internal 1.2μA soft-start current charges the capacitor to create a voltage ramp at the pin. Leave these pins disconnected if unused. VC1, VC2: The VC pins are the outputs of the internal error amps. The voltages on these pins control the peak switch currents. These pins are normally used to compensate the control loops, but can also be used to override the loops. Pull these pins to ground with an open drain to shut down each switching regulator. VIN1: The VIN1 pin supplies current to the LT3508 internal circuitry and to the internal power switch connected to SW1 and must be locally bypassed. VIN1 must be greater than 3.7V for channel 1 or channel 2 to operate. VIN2: The VIN2 pin supplies current to the internal power switch connected to SW2 and must be locally bypassed. Connect this pin directly to VIN1 unless power for channel 2 is coming from a different source. VIN2 must be greater than 3V and VIN1 must be greater than 3.7V for channel 2 to operate. 3508fb 6 LT3508 BLOCK DIAGRAM SHDN VIN1 INT REG AND REF RT/SYNC CLK1 MASTER OSC CLK2 1.2μA VIN TRACK/SS VIN CIN 0.75V + 3 SLOPE R S C1 BOOST D2 Q SLAVE OSC CLK C3 SW L1 OUT + ERROR AMP 0.625V VC – TRACK/SS C1 R1 R2 0.80V CC + + ILIMIT CLAMP 75mV PG GND + – CF RC FB + + – – D1 3508 F01 Figure 1. Block Diagram of the LT3508 with Associated External Components (One of Two Switching Regulators Shown) 3508fb 7 LT3508 OPERATION The LT3508 is a dual constant frequency, current mode regulator with internal power switches. Operation can be best understood by referring to the Block Diagram. If the SHDN pin is tied to ground, the LT3508 is shut down and draws minimal current from the input source tied to the VIN pins. If the SHDN pin exceeds 1V, the internal bias circuits turn on, including the internal regulator, reference and oscillator. The switching regulators will only begin to operate when the SHDN pin exceeds 2.63V. The switcher is a current mode regulator. Instead of directly modulating the duty cycle of the power switch, the feedback loop controls the peak current in the switch during each cycle. Compared to voltage mode control, current mode control improves loop dynamics and provides cycle-bycycle current limit. A pulse from the oscillator sets the RS flip-flop and turns on the internal NPN power switch. Current in the switch and the external inductor begins to increase. When this current exceeds a level determined by the voltage at VC, current comparator C1 resets the flip-flop, turning off the switch. The current in the inductor flows through the external Schottky diode and begins to decrease. The cycle begins again at the next pulse from the oscillator. In this way, the voltage on the VC pin controls the current through the inductor to the output. The internal error amplifier regulates the output current by continually adjusting the VC pin voltage. The threshold for switching on the VC pin is 0.8V, and an active clamp of 1.75V limits the output current. The switching frequency is set either by the resistance to GND at the RT/SYNC pin or the frequency of the logic-level signal driving the RT/SYNC pin. A detection circuit monitors for the presence of a SYNC signal on the pin and switches between the two modes. Unique circuitry generates the appropriate slope compensation ramps and generates the 180° out-of-phase clocks for the two channels. The switching regulator performs frequency foldback during overload conditions. An amplifier senses when VFB is less than 0.625V and begins decreasing the oscillator frequency down from full frequency to 12% of the nominal frequency when VFB = 0V. The FB pin is less than 0.8V during start-up, short-circuit and overload conditions. Frequency foldback helps limit switch current under these conditions. The switch driver operates either from VIN or from the BOOST pin. An external capacitor and Schottky diode are used to generate a voltage at the BOOST pin that is higher than the input supply. This allows the driver to saturate the internal bipolar NPN power switch for efficient operation. The TRACK/SS pin serves as an alternative input to the error amplifier. The amplifier will use the lowest voltage of either the reference of 0.8V or the voltage on the TRACK/SS pin as the positive input of error amplifier. Since the TRACK/SS pin is driven by a constant current source, a single capacitor on the pin will generate a linear ramp on the output voltage. Tying the TRACK/SS pin to a resistor divider from the output of one of the switching regulators allows one output to track another. The PG output is an open-collector transistor that is off when the output is in regulation, allowing an external resistor to pull the PG pin high. Power good is valid when the LT3508 is enabled (SHDN is high) and VIN1 is greater than ~2.4V. 3508fb 8 LT3508 APPLICATIONS INFORMATION Setting the Output Voltage The output voltage is programmed with a resistor divider between the output and the FB pin. Choose the 1% resistors according to: ⎛V ⎞ R1 = R2 ⎜ OUT – 1⎟ ⎝ 0.8 V ⎠ R2 should be 20k or less to avoid bias current errors. Reference designators refer to the Block Diagram. Minimum Operating Voltage The minimum operating voltage is determined either by the LT3508’s undervoltage lockout or by its maximum duty cycle. If VIN1 and VIN2 are tied together, the undervoltage lockout is at 3.7V or below. If the two inputs are used separately, then VIN1 has an undervoltage lockout of 3.7V or below and VIN2 has an undervoltage lockout of 3V or below. Because the internal supply runs off VIN1, channel 2 will not operate unless VIN1 > 3.7V. The duty cycle is the fraction of time that the internal switch is on and is determined by the input and output voltages: DC = VOUT + VF VIN – VSW + VF Unlike many fixed frequency regulators, the LT3508 can extend its duty cycle by turning on for multiple cycles. The LT3508 will not switch off at the end of each clock cycle if there is sufficient voltage across the boost capacitor (C3 in Figure 1). Eventually, the voltage on the boost capacitor falls and requires refreshing. Circuitry detects this condition and forces the switch to turn off, allowing the inductor current to charge up the boost capacitor. This places a limitation on the maximum duty cycle as follows: DCMAX = 1 1+ 1 β SW where βSW is equal to the SW pin current divided by the BOOST pin current as shown in the Typical Performance Characteristics section. This leads to a minimum input voltage of: VIN(MIN) = VOUT + VF – VF + VSW DCMAX where VF is the forward voltage drop of the catch diode (~0.4V) and VSW is the voltage drop of the internal switch (~0.4V at maximum load). Example: ISW = 1.5A and IBOOST = 50mA, VOUT = 3.3V, βSW = 1.5A/50mA = 30, DCMAX = 1/(1+1/30) = 96%: VIN(MIN) = 3.3V + 0.4V – 0.4V + 0.4V = 3.8 V 96% Maximum Operating Voltage The maximum operating voltage is determined by the Absolute Maximum Ratings of the VIN and BOOST pins, and by the minimum duty cycle: DCMIN = tON(MIN) • f where tON(MIN) is equal to 130ns (for TJ > 125°C tON(MIN) is equal to 150ns) and f is the switching frequency. Running at a lower switching frequency allows a lower minimum duty cycle. The maximum input voltage before pulse skipping occurs depends on the output voltage and the minimum duty cycle: VIN(PS) = VOUT + VF – VF + VSW DCMIN Example: f = 790kHz, VOUT = 3.3V, DCMIN = 130ns • 790kHz = 0.103: VIN(PS) = 3.3V + 0.4V – 0.4V + 0.4V = 36 V 0.103 The LT3508 will regulate the output current at input voltages greater than VIN(PS). For example, an application with an output voltage of 1.8V and switching frequency of 1.5MHz has a VIN(PS) of 11.3V, as shown in Figure 2. Figure 3 shows operation at 18V. Output ripple and peak inductor current have significantly increased. Exceeding VIN(PS) is safe if the output is in regulation, if the external components have adequate ratings to handle the peak conditions and if the peak inductor current does not exceed 3.2A. A saturating inductor may further reduce performance. Do not exceed VIN(PS) during start-up or overload conditions (for outputs greater than 5V, use VOUT = 5V to calculate VIN(PS)). For operation above 20V in pulse skipping mode, program the switching frequency to 1.1MHz or less. 3508fb 9 LT3508 APPLICATIONS INFORMATION Table 1. Programming the Switching Frequency VOUT 100mV/DIV (AC) SWITCHING FREQUENCY (MHz) RT (kΩ) 2.5 7.50 2.2 9.76 2 11.5 IL 500mA/DIV 2μs/DIV 3508 F02 Figure 2. Operation Below VIN(PS). VIN = 10V, VOUT = 1.8V and fSW = 1.5MHz VOUT 100mV/DIV (AC) IL 500mA/DIV 2μs/DIV 3508 F03 Figure 3. Operation Above VIN(PS). VIN = 18V, VOUT = 1.8V and fSW = 1.5MHz. Output Ripple and Peak Inductor Current Increase 1.8 14 1.6 16.9 1.4 20.5 1.2 26.1 1 33.2 0.9 38.3 0.8 44.2 0.7 52.3 0.6 61.9 0.5 76.8 0.45 88.7 0.4 100 0.35 115 0.3 140 0.25 169 Setting the Switching Frequency Inductor Selection and Maximum Output Current The switching frequency is programmed either by driving the RT/SYNC pin with a logic level SYNC signal or by tying a resistor from the RT/SYNC pin to ground. A graph for selecting the value of RT for a given operating frequency is shown in the Typical Application section. Suggested programming resistors for various switching frequencies are shown in Table 1. A good first choice for the inductor value is: 1.2MHz L = (VOUT + VF ) • f where VF is the voltage drop of the catch diode (~0.4V) and L is in μH. The inductor’s RMS current rating must be greater than the maximum load current and its saturation current should be at least 30% higher. For highest efficiency, the series resistance (DCR) should be less than 0.1Ω. Table 2 lists several vendors and types that are suitable. Choosing a high switching frequency will allow the smallest overall solution size. However, at high input voltages the efficiency can drop significantly with increasing switching frequency. The choice of switching frequency will also impact the input voltage range, inductor and capacitor selection, and compensation. See the related sections for details. Table 2. Inductor Vendors VENDOR Coilcraft Murata TDK URL www.coilcraft www.murata.com www.component.tdk.com Toko www.toko.com Sumida www.sumida.com PART SERIES MSS7341 LQH55D SLF7045 SLF10145 DC62CB D63CB D75C D75F CR54 CDRH74 CDRH6D38 CR75 TYPE Shielded Open Shielded Shielded Shielded Shielded Shielded Open Open Shielded Shielded Open 3508fb 10 LT3508 APPLICATIONS INFORMATION The optimum inductor for a given application may differ from the one indicated by this simple design guide. A larger value inductor provides a higher maximum load current, and reduces the output voltage ripple. If your load is lower than the maximum load current, then you can relax the value of the inductor and operate with higher ripple current. This allows you to use a physically smaller inductor, or one with a lower DCR resulting in higher efficiency. Be aware that if the inductance differs from the simple rule above, then the maximum load current will depend on input voltage. In addition, low inductance may result in discontinuous mode operation, which further reduces maximum load current. For details of maximum output current and discontinuous mode operation, see Linear Technology’s Application Note 44. Finally, for duty cycles greater than 50% (VOUT/VIN > 0.5), a minimum inductance is required to avoid sub-harmonic oscillations: 800kHz LMIN = (VOUT + VF ) • f The current in the inductor is a triangle wave with an average value equal to the load current. The peak switch current is equal to the output current plus half the peak-to-peak inductor ripple current. The LT3508 limits its switch current in order to protect itself and the system from overload faults. Therefore, the maximum output current that the LT3508 will deliver depends on the switch current limit, the inductor value, and the input and output voltages. When the switch is off, the potential across the inductor is the output voltage plus the catch diode drop. This gives the peak-to-peak ripple current in the inductor: ΔIL = (1– DC)(VOUT + VF ) L•f where f is the switching frequency of the LT3508 and L is the value of the inductor. The peak inductor and switch current is: ISW(PK ) = IL(PK ) = IOUT + ΔIL 2 To maintain output regulation, this peak current must be less than the LT3508’s switch current limit ILIM. ILIM is at least 2A for at low duty cycles and decreases linearly to 1.55A at DC = 90%. The maximum output current is a function of the chosen inductor value: IOUT(MAX ) = ILIM – ΔIL ΔI = 2A • (1 – 0.25 • DC) – L 2 2 Choosing an inductor value so that the ripple current is small will allow a maximum output current near the switch current limit. One approach to choosing the inductor is to start with the simple rule given above, look at the available inductors, and choose one to meet cost or space goals. Then use these equations to check that the LT3508 will be able to deliver the required output current. Note again that these equations assume that the inductor current is continuous. Discontinuous operation occurs when IOUT is less than ΔIL/2. Input Capacitor Selection Bypass the VIN pins of the LT3508 circuit with a ceramic capacitor of X7R or X5R type. For switching frequencies above 500kHz, use a 4.7μF capacitor or greater. For switching frequencies below 500kHz, use a 10μF or higher capacitor. If the VIN pins are tied together only a single capacitor is necessary. If the VIN pins are separated, each pin will need its own bypass. The following paragraphs describe the input capacitor considerations in more detail. Step-down regulators draw current from the input supply in pulses with very fast rise and fall times. The input capacitor is required to reduce the resulting voltage ripple at the LT3508 input and to force this switching current into a tight local loop, minimizing EMI. The input capacitor must have low impedance at the switching frequency to do this effectively, and it must have an adequate ripple current rating. With two switchers operating at the same frequency but with different phases and duty cycles, calculating the input capacitor RMS current is not simple. However, a conservative value is the RMS input current for the channel that is delivering most power (VOUT times IOUT): CIN(RMS) = IOUT • VOUT (VIN – VOUT ) VIN < IOUT 2 and is largest when VIN = 2VOUT (50% duty cycle). As the second, lower power channel draws input current, 3508fb 11 LT3508 APPLICATIONS INFORMATION the input capacitor’s RMS current actually decreases as the out-of-phase current cancels the current drawn by the higher power channel. Considering that the maximum load current from a single channel is ~1.4A, RMS ripple current will always be less than 0.7A. The high frequency of the LT3508 reduces the energy storage requirements of the input capacitor. The combination of small size and low impedance (low equivalent series resistance or ESR) of ceramic capacitors makes them the preferred choice. The low ESR results in very low voltage ripple. Ceramic capacitors can handle larger magnitudes of ripple current than other capacitor types of the same value. Use X5R and X7R types. An alternative to a high value ceramic capacitor is a lower value ceramic along with a larger electrolytic capacitor. The electrolytic capacitor likely needs to be greater than 10μF in order to meet the ESR and ripple current requirements. The input capacitor is likely to see high surge currents when the input source is applied. Tantalum capacitors can fail due to an oversurge of current. Only use tantalum capacitors with the appropriate surge current rating. The manufacturer may also recommend operation below the rated voltage of the capacitor. A final caution is in order regarding the use of ceramic capacitors at the input. A ceramic input capacitor can combine with stray inductance to form a resonant tank circuit. If power is applied quickly (for example by plugging the circuit into a live power source), this tank can ring, doubling the input voltage and damaging the LT3508. The solution is to either clamp the input voltage or dampen the tank circuit by adding a lossy capacitor in parallel with the ceramic capacitor. For details see Application Note 88. LT3508’s control loop. Ceramic capacitors have very low equivalent series resistance (ESR) and provide the best ripple performance. A good value is: COUT = where COUT is in μF. Use X5R or X7R types. This choice will provide low output ripple and good transient response. Transient performance can be improved with a high value capacitor if the compensation network is also adjusted to maintain the loop bandwidth. A lower value of output capacitor can be used, but transient performance will suffer. With an external compensation network, the loop gain can be lowered to compensate for the lower capacitor value. Look carefully at the capacitor’s data sheet to find out what the actual capacitance is under operating conditions (applied voltage and temperature). A physically larger capacitor, or one with a higher voltage rating, may be required. High performance electrolytic capacitors can be used for the output capacitor. Low ESR is important, so choose one that is intended for use in switching regulators. The ESR should be specified by the supplier, and should be 0.05Ω or less. Such a capacitor will be larger than a ceramic capacitor and will have a larger capacitance, because the capacitor must be large to achieve low ESR. Table 3 lists several capacitor vendors. Table 3. Capacitor Vendors VENDOR PART SERIES COMMENTS Panasonic Ceramic Polymer Tantalum EEF Series Kemet Sanyo Output Capacitor Selection The output capacitor has two essential functions. Along with the inductor, it filters the square wave generated by the LT3508 to produce the DC output. In this role it determines the output ripple, and low impedance at the switching frequency is important. The second function is to store energy in order to satisfy transient loads and stabilize the 50 V 1MHz • VOUT f Ceramic Tantalum Ceramic Polymer Tantalum Murata Ceramic AVX Ceramic Tantalum Taiyo Yuden Ceramic TDK Ceramic T494, T495 POSCAP TPS Series 3508fb 12 LT3508 APPLICATIONS INFORMATION Diode Selection The catch diode (D1 from Figure 1) conducts current only during switch off time. Average forward current in normal operation can be calculated from: ID( AVG) = IOUT (VIN – VOUT ) VIN The only reason to consider a diode with a larger current rating than necessary for nominal operation is for the worst-case condition of shorted output. The diode current will then increase to the typical peak switch current. Peak reverse voltage is equal to the regulator input voltage. Use a diode with a reverse voltage rating greater than the input voltage. Table 4 lists several Schottky diodes and their manufacturers. If operating at high ambient temperatures, consider using a Schottky with low reverse leakage. D2 VF at 1A (mV) VR (V) IAVE (A) MBR0520L 20 0.5 MBR0540 40 0.5 620 MBRM120E 20 1 530 MBRM140 40 1 550 C3 BOOST LT3508 VIN Table 4. Schottky Diodes PART NUMBER and higher, the standard circuit (Figure 4a) is best. For outputs between 2.8V and 3.3V, use a small Schottky diode (such as the BAT-54). For lower output voltages, the boost diode can be tied to the input (Figure 4b). The circuit in Figure 4a is more efficient because the boost pin current comes from a lower voltage source. Finally, the anode of the boost diode can be tied to another source that is at least 3V (Figure 4c). For example, if you are generating a 3.3V output, and the 3.3V output is on whenever the particular channel is on, the anode of the BOOST diode can be connected to the 3.3V output. In any case, be sure that the maximum voltage at the BOOST pin is both less than 60V and the voltage difference between the BOOST and SW pins is less than 30V. VIN VF at 2A (mV) VOUT SW GND On Semiconductor VBOOST – VSW VOUT MAX VBOOST VIN + VOUT (4a) D2 C3 BOOST Diodes Inc. LT3508 B0530W 30 0.5 B120 20 1 500 B130 30 1 500 B140HB 40 1 DFLS140 40 1.1 B240 40 2 VIN VIN VOUT SW GND VBOOST – VSW VIN MAX VBOOST 2VIN 510 (4b) 500 D2 BOOST Pin Considerations The capacitor and diode tied to the BOOST pin generate a voltage that is higher than the input voltage. In most cases, a 0.22μF capacitor and fast switching diode (such as the CMDSH-3 or MMSD914LT1) will work well. For applications 1MHz or faster, a 0.1μF capacitor is sufficient. Use a 0.47μF capacitor or greater for applicaitons running below 500kHz. Figure 4 shows three ways to arrange the boost circuit. The BOOST pin must be more than 2.5V above the SW pin for full efficiency. For outputs of 3.3V VIN2 > 3V BOOST C3 LT3508 VIN VIN VOUT SW GND VBOOST – VSW VIN2 MAX VBOOST VIN2 + VIN MINIMUM VALUE FOR VIN2 = 3V 3508 F04 (4c) Figure 4. Generating the Boost Voltage 3508fb 13 LT3508 APPLICATIONS INFORMATION The minimum operating voltage of an LT3508 application is limited by the undervoltage lockout (≈3.7V) and by the maximum duty cycle. The boost circuit also limits the minimum input voltage for proper start-up. If the input voltage ramps slowly, or the LT3508 turns on when the output is already in regulation, the boost capacitor may not be fully charged. Because the boost capacitor charges with the energy stored in the inductor, the circuit will rely on some minimum load current to get the boost circuit running properly. This minimum load will depend on input and output voltages, and on the arrangement of the boost circuit. The minimum load current generally goes to zero once the circuit has started. Figure 5 shows a plot of minimum load to start and to run as a function of input voltage. Even without an output load current, in many Minimum Input Voltage, VOUT = 3.3V 6.5 TA = 25°C VOUT = 3.3V INPUT VOLTAGE (V) 6.0 5.5 5.0 TO START 4.5 4.0 TO RUN 3.5 3.0 1 10 100 1000 LOAD CURRENT (mA) 10000 3508 F05a Minimum Input Voltage, VOUT = 5V 9 TA = 25°C VOUT = 5V INPUT VOLTAGE (V) 8 7 TO START 6 TO RUN 5 4 1 100 10 1000 LOAD CURRENT (mA) 10000 3508 G05b Figure 5. The Minimum Input Voltage Depends on Output Voltage, Load Current and Boost Circuit cases the discharged output capacitor will present a load to the switcher that will allow it to start. The plots show the worst case, where VIN is ramping very slowly. Frequency Compensation The LT3508 uses current mode control to regulate the output. This simplifies loop compensation. In particular, the LT3508 does not require the ESR of the output capacitor for stability, so you are free to use ceramic capacitors to achieve low output ripple and small circuit size. Frequency compensation is provided by the components tied to the VC pin, as shown in Figure 1. Generally a capacitor (CC) and a resistor (RC) in series to ground are used. In addition, there may be a lower value capacitor in parallel. This capacitor (CF) is not part of the loop compensation but is used to filter noise at the switching frequency, and is required only if a phase-lead capacitor is used or if the output capacitor has high ESR. Loop compensation determines the stability and transient performance. Designing the compensation network is a bit complicated and the best values depend on the application and in particular the type of output capacitor. A practical approach is to start with one of the circuits in this data sheet that is similar to your application and tune the compensation network to optimize the performance. Stability should then be checked across all operating conditions, including load current, input voltage and temperature. The LT1375 data sheet contains a more thorough discussion of loop compensation and describes how to test the stability using a transient load. Figure 6 shows an equivalent circuit for the LT3508 control loop. The error amplifier is a transconductance amplifier with finite output impedance. The power section, consisting of the modulator, power switch and inductor, is modeled as a transconductance amplifier generating an output current proportional to the voltage at the VC pin. Note that the output capacitor integrates this current, and that the capacitor on the VC pin (CC) integrates the error amplifier output current, resulting in two poles in the loop. In most cases a zero is required and comes from either the output capacitor ESR or from a resistor RC in series with CC. This simple model works well as long as the value of the inductor is not too high and the loop crossover frequency 3508fb 14 LT3508 APPLICATIONS INFORMATION is much lower than the switching frequency. A phase-lead capacitor (CPL) across the feedback divider may improve the transient response. LT3508 CURRENT MODE POWER STAGE gm = 2.5S VSW ERROR AMPLIFIER OUTPUT R1 CPL ESR – + 0.8V C1 + VC GND If an adjustable UVLO threshold is required, the SHDN pin can be used. The threshold voltage of the SHDN pin comparator is 2.63V. Current hysteresis is added above the SHDN threshold. This can be used to set voltage hysteresis of the UVLO using the following: FB gm = 300μS 2M used to prevent excessive discharge of battery-operated systems. R3 = VH – VL 7.5μA R4 = 2.63V VH – 2.63V – 8μA R3 C1 R2 RC CF POLYMER OR TANTALUM CERAMIC CC Example: switching should not start until the input is above 4.75V and is to stop if the input falls below 4V. VH = 4.75V, VL = 4.0 V 3508 F06 Figure 6. Model for Loop Response Shutdown and Undervoltage Lockout Figure 7 shows how to add undervoltage lockout (UVLO) to the LT3508. Typically, UVLO is used in situations where the input supply is current limited, or has a relatively high source resistance. A switching regulator draws constant power from the source, so source current increases as source voltage drops. This looks like a negative resistance load to the source and can cause the source to current limit or latch low under low source voltage conditions. UVLO prevents the regulator from operating at source voltages where the problems might occur. An internal comparator will force the part into shutdown below the minimum VIN1 of 3.7V. This feature can be LT3508 VIN 2.6V – VC R3 SHDN C1 + R4 TRACK/SS 8μA 7.5μA 4.75V – 4V = 100k 7.5μA R4 = 2.663V = 200k 4.75V – 2.63V – 8μA 100k Keep the connection from the resistor to the SHDN pin short and make sure the interplane or surface capacitance to switching nodes is minimized. If high resistor values are used, the SHDN pin should be bypassed with a 1nF capacitor to prevent coupling problems from the switch node. Soft-Start The output of the LT3508 regulates to the lowest voltage present at either the TRACK/SS pin or an internal 0.8V reference. A capacitor from the TRACK/SS pin to ground is charged by an internal 1.2μA current source resulting in a linear output ramp from 0V to the regulated output whose duration is given by: tRAMP = 3508 F07 Figure 7. Undervoltage Lockout R3 = CSS • 0.8 V 1.2 μA At power up, internal open-collector ouputs discharge both TRACK/SS pins. The pins clamp at 1.3V. 3508fb 15 LT3508 APPLICATIONS INFORMATION Output Tracking and Sequencing Complex output tracking and sequencing between channels can be implemented using the LT3508’s TRACK/SS and PG pins. Figure 8 shows several configurations for output tracking and sequencing of 5V and 3.3V applications. Independent Start-Up Independent soft-start for each channel is shown in Figure 8a. The output ramp time for each channel is set by the soft-start capacitor as described in the soft-start section. Ratiometric Start-Up Coincident Start-Up VOUT1 VOUT1 VOUT2 VOUT1 VOUT2 1V/DIV VOUT2 1V/DIV 1V/DIV 20ms/DIV 20ms/DIV TRACK/SS1 VOUT1 5V 20ms/DIV 5V TRACK/SS1 VOUT1 0.1μF LT3508 TRACK/SS2 VOUT2 LT3508 3.3V 5V TRACK/SS1 VOUT1 0.1μF 0.22μF LT3508 3.3V TRACK/SS2 VOUT2 3.3V TRACK/SS2 VOUT2 0.047μF R1 28.7k R2 10.0k (8a) (8b) (8c) Output Sequencing Controlled Power Up and Down VOUT1 VOUT1 VOUT2 VOUT2 1V/DIV 1V/DIV EXTERNAL SOURCE 20ms/DIV 20ms/DIV TRACK/SS1 VOUT1 0.1μF 5V TRACK/SS1 VOUT1 EXTERNAL SOURCE LT3508 PG1 TRACK/SS2 VOUT2 3.3V + – 5V LT3508 TRACK/SS2 VOUT2 3.3V 0.047μF R1 28.7k R2 10.0k (8d) (8e) Figure 8 3508fb 16 LT3508 APPLICATIONS INFORMATION inductor size by allowing an increase in frequency. A dual step-down application (Figure 9) steps down the input voltage (VIN1) to the highest output voltage, then uses that voltage to power the second output (VIN2). VOUT1 must be able to provide enough current for its output plus the input current at VIN2 when VOUT2 is at its maximum load. Ratiometric tracking is achieved in Figure 8b by connecting both the TRACK/SS pins together. In this configuration the TRACK/SS pin source current is doubled (2.4μA) which must be taken into account when calculating the output rise time. By connecting a feedback network from VOUT1 to the TRACK/SS2 pin with the same ratio that set the VOUT2 voltage, absolute tracking shown in Figure 8c is implemented. A small VOUT2 voltage offset will be present due to the TRACK/SS2 1.2μA source current. This offset can be corrected for by slightly reducing the value of R2. Use a resistor divider such that when VOUT1 is in regulation, TRACK/SS2 is pulled up to 1V or greater. If TRACK/SS is below 1V, the output may regulate FB to a voltage lower than the 800mV reference voltage. For applications with multiple input voltages, the LT3508 can accommodate input voltages as low as 3V on VIN2. This can be useful in applications regulating outputs from a PCI Express bus, where the 12V input is power limited and the 3.3V input has power available to drive other outputs. In this case, tie the 12V input to VIN1 and the 3.3V input to VIN2. See the Typical Application section for an example circuit. Do not tie TRACK/SS1 and TRACK/SS2 together if using multiple inputs. If VIN2 is below 3V, TRACK/SS2 pulls low and would hold TRACK/SS1 low as well if the two pins are tied together, which would prevent channel 1 from operating. Figure 8d illustrates output sequencing. When VOUT1 is within 10% of its regulated voltage, PG1 releases the TRACK/SS2 soft-start pin allowing VOUT2 to softstart. In this case PG1 will be pulled up to 1.3V by the TRACK/SS pin. Shorted and Reverse Input Protection If precise output ramp up and down is required, drive the TRACK/SS pins as shown in Figure 8e. If the inductor is chosen so that it won’t saturate excessively, an LT3508 step-down regulator will tolerate a shorted output. There is another situation to consider in systems where the output will be held high when the input to the LT3508 is absent. This may occur in battery charging Multiple Inputs For applications requiring large inductors due to high VIN to VOUT ratios, a 2-stage step down approach may reduce VIN 5.7V TO 36V C1 4.7μF ON OFF D1 OUT1 VIN1 VIN2 SHDN BOOST1 OUT1 5V 0.9A BOOST2 C2 0.1μF L1 6.8μH C3 0.1μF SW1 D3 R1 56.2k C4 10μF R5 39k C6 100pF C8 1nF L2 3.3μH OUT2 1.8V 1A SW2 D4 LT3508 FB1 R3 10.7k D2 R2 18.7k FB2 VC1 VC2 TRACK/SS1 TRACK/SS2 PG1 PG2 GND R6 47k R4 15.0k R7 100k RT/SYNC R8 33.2k C9 3.3nF C5 47μF C7 330pF fSW = 1MHz 3508 F09 POWER GOOD Figure 9. 1MHz, Wide Input Range 5V and 1.8V Outputs 3508fb 17 LT3508 APPLICATIONS INFORMATION applications or in battery back-up systems where a battery or some other supply is diode OR-ed with the LT3508’s output. If the VIN pin is allowed to float and the SHDN pin is held high (either by a logic signal or because it is tied to VIN), then the LT3508’s internal circuitry will pull its quiescent current through its SW pin. This is fine if your system can tolerate a few mA in this state. If you ground the SHDN pin, the SW pin current will drop to essentially zero. However, if the VIN pin is grounded while the output is held high, then parasitic diodes inside the LT3508 can pull large currents from the output through the SW pin and the VIN pin. Figure 10 shows a circuit that will run only when the input voltage is present and that protects against a shorted or reversed input. PARASITIC DIODE D4 VIN VIN SW VOUT LT3508 PCB Layout For proper operation and minimum EMI, care must be taken during printed circuit board layout. Figure 11 shows the recommended PCB layout with trace and via locations. Note that large, switched currents flow in the LT3508’s VIN and SW pins, the catch diode (D1) and the input capacitor (CIN). The loop formed by these components should be as small as possible. These components, along with the inductor and output capacitor, should be placed on the same side of the circuit board, and their connections should be made on that layer. Place a local, unbroken ground plane below these components. The SW and BOOST nodes should be as small as possible. Finally, keep the FB and VC nodes small so that the ground traces will shield them from the SW and BOOST nodes. The Exposed Pad on the bottom of the package must be soldered to ground so that the pad acts as a heat sink. To keep thermal resistance low, extend the ground plane as much as possible, and add thermal vias under and near the LT3508 to additional ground planes within the circuit board and on the bottom side. 3508 F10 Figure 10. Diode D4 Prevents a Shorted Input from Discharging a Backup Battery Tied to the Output (11a) Example Layout for FE16 Package (11b) Example Layout for QFN Package Figure 11. A Good PCB Layout Ensures Proper Low EMI Operation 3508fb 18 LT3508 APPLICATIONS INFORMATION was 13°C; for 24VIN to 3.3VOUT the rise was 18°C; for 12VIN to 5VOUT the rise was 14°C and for 24VIN to 5VOUT the rise was 19°C. High Temperature Considerations The die temperature of the LT3508 must be lower than the maximum rating of 125°C (150°C for the H grade). This is generally not a concern unless the ambient temperature is above 85°C. For higher temperatures, care should be taken in the layout of the circuit to ensure good heat sinking of the LT3508. The maximum load current should be derated as the ambient temperature approaches 125°C (150°C for the H grade). The die temperature is calculated by multiplying the LT3508 power dissipation by the thermal resistance from junction to ambient. Power dissipation within the LT3508 can be estimated by calculating the total power loss from an efficiency measurement and subtracting the catch diode loss. Thermal resistance depends on the layout of the circuit board, but values from 30°C/W to 60°C/W are typical. Die temperature rise was measured on a 4-layer, 6.5cm × 7.5cm circuit board in still air at a load current of 1.4A (fSW = 700kHz). For a 12V input to 3.3V output the die temperature elevation above ambient Outputs Greater Than 6V For outputs greater than 6V, add a resistor of 1k to 2.5k across the inductor to damp the discontinuous ringing of the SW node, preventing unintended SW current. The 12V output circuit in the Typical Applications section shows the location of this resistor. Other Linear Technology Publications Application Notes 19, 35 and 44 contain more detailed descriptions and design information for step-down regulators and other switching regulators. The LT1376 data sheet has a more extensive discussion of output ripple, loop compensation and stability testing. Design Note 318 shows how to generate a dual polarity output supply using a step-down regulator. TYPICAL APPLICATIONS 1MHz, 3.3V and 1.8V Outputs with Sequencing VIN 3.9V TO 16V C1 4.7μF D1 OUT2 OUT1 1.8V 1.4A ON OFF VIN1 VIN2 SHDN BOOST1 C2 0.1μF L1 3.3μH C3 0.1μF SW1 D3 R1 18.7k C4 47μF R5 47k C6 330pF D4 LT3508 L2 4.7μH R2 35.7k FB2 VC1 VC2 TRACK/SS1 TRACK/SS2 PG1 PG2 GND R6 39k R8 33.2k fSW = 1MHz R4 11.5k C5 10μF R7 100k RT/SYNC C8 1nF C1 TO C5: X5R OR X7R D1, D2: MMSD4148 D3: DIODES INC. B140 D4: DIODES INC. B240A OUT2 3.3V 1.4A SW2 FB1 R3 15.0k D2 BOOST2 C7 150pF 3508 TA02 POWER GOOD 3508fb 19 LT3508 TYPICAL APPLICATIONS 3.3V and 5V Dual Output Step-Down Converter with Output Sequencing VIN 5.7V TO 36V C1 4.7μF D1 ON OFF VIN1 VIN2 SHDN BOOST1 C2 0.22μF L1 6.8μH OUT1 3.3V 1.4A C3 0.22μF SW1 D3 R1 35.7k R5 51k C6 150pF C4 22μF D4 LT3508 L2 10μH R2 56.2k FB2 VC1 VC2 TRACK/SS1 TRACK/SS2 PG1 PG2 GND R4 10.7k R6 43k R8 52.3k C5 10μF R7 100k RT/SYNC C8 1nF C1 TO C5: X5R OR X7R D1, D2: MMSD4148 D3: DIODES INC. B140 D4: DIODES INC. B240A OUT2 5V 1.4A SW2 FB1 R3 11.5k D2 BOOST2 C7 100pF fSW = 700kHz 3508 TA03 POWER GOOD 1MHz, Wide Input Range 5V and 1.8V Outputs VIN 5.7V TO 36V C1 4.7μF ON OFF D1 OUT1 VIN1 VIN2 BOOST1 OUT1 5V 0.9A BOOST2 C2 0.1μF L1 6.8μH C3 0.1μF SW1 D3 R1 56.2k C4 10μF R5 39k C6 100pF C8 1nF C1 TO C5: X5R OR X7R D1, D2: MMSD4148 D3: DIODES INC. B240A D4: DIODES INC. B120 L2 3.3μH OUT2 1.8V 1A SW2 D4 LT3508 FB1 R3 10.7k D2 SHDN R2 18.7k FB2 VC1 VC2 TRACK/SS1 TRACK/SS2 PG1 PG2 GND R6 47k R8 33.2k fSW = 1MHz C5 47μF R7 100k RT/SYNC C9 3.3nF R4 15.0k C7 330pF 3508 TA04 POWER GOOD 3508fb 20 LT3508 TYPICAL APPLICATIONS 1MHz, 5V and 12V Outputs VIN 14V TO 36V C1 4.7μF D1 OUT2 OUT1 12V 1.4A* ON OFF VIN1 VIN2 SHDN BOOST1 D2 C3 0.1μF C2 0.1μF L1 15μH SW1 R2 1k D3 D4 LT3508 FB1 C4 4.7μF R5 43k C6 100pF C8 1nF L2 6.8μH SW2 R1 154k R4 11.0k OUT2 5V 1.4A* BOOST2 FB2 VC1 VC2 TRACK/SS1 TRACK/SS2 PG1 PG2 GND R3 56.2k R6 39k R8 100k RT/SYNC R9 33.2k C5 10μF R7 10.7k C7 100pF fSW = 1MHz C1 TO C5: X5R OR X7R D1, D2: MMSD4148 D3: DIODES INC. B240A D4: DIODES INC. B140 R2: USE 0.25W RESISTOR. FOR CONTINUOUS OPERATION ABOVE 30V, USE TWO 2k, 0.25W RESISTORS IN PARALLEL 3508 TA06 POWER GOOD *DERATE OUTPUT CURRENT AT HIGHER AMBIENT TEMPERATURES AND INPUT VOLTAGES TO MAINTAIN JUNCTION TEMPERATURE BELOW THE ABSOLUTE MAXIMUM 3508fb 21 LT3508 PACKAGE DESCRIPTION FE Package 16-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG # 05-08-1663) Exposed Pad Variation BA 4.90 – 5.10* (.193 – .201) 2.74 (.108) 2.74 (.108) 16 1514 13 12 1110 6.60 ±0.10 9 2.74 (.108) 4.50 ±0.10 2.74 6.40 (.108) (.252) BSC SEE NOTE 4 0.45 ±0.05 1.05 ±0.10 0.65 BSC 1 2 3 4 5 6 7 8 RECOMMENDED SOLDER PAD LAYOUT 4.30 – 4.50* (.169 – .177) 0.09 – 0.20 (.0035 – .0079) 0.50 – 0.75 (.020 – .030) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES) 3. DRAWING NOT TO SCALE 0.25 REF 1.10 (.0433) MAX 0° – 8° 0.65 (.0256) BSC 0.195 – 0.30 (.0077 – .0118) TYP 0.05 – 0.15 (.002 – .006) FE16 (BA) TSSOP 0204 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE 3508fb 22 LT3508 PACKAGE DESCRIPTION UF Package 24-Lead Plastic QFN (4mm × 4mm) (Reference LTC DWG # 05-08-1697) 0.70 ±0.05 4.50 ± 0.05 2.45 ± 0.05 3.10 ± 0.05 (4 SIDES) PACKAGE OUTLINE 0.25 ±0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 4.00 ± 0.10 (4 SIDES) BOTTOM VIEW—EXPOSED PAD 0.75 ± 0.05 R = 0.115 TYP PIN 1 NOTCH R = 0.20 TYP OR 0.35 × 45° CHAMFER 23 24 0.40 ± 0.10 PIN 1 TOP MARK (NOTE 6) 1 2 2.45 ± 0.10 (4-SIDES) (UF24) QFN 0105 0.200 REF 0.00 – 0.05 0.25 ± 0.05 0.50 BSC NOTE: 1. DRAWING PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGD-X)—TO BE APPROVED 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE, IF PRESENT 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3508fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 23 LT3508 TYPICAL APPLICATION 5V, 1.8V Output from PCI Express VIN 12V C1 4.7μF R9 40.2k OUT1 5V 0.9A VIN2 3.3V D2 SHDN D1 R10 14.7k VIN2 VIN1 C2 4.7μF BOOST1 BOOST2 C3 0.1μF L1 6.8μH C4 0.1μF SW1 D3 R1 52.3k R5 43k C9 100pF C6 10μF D4 LT3508 C8 0.047μF R2 18.7k FB2 VC1 VC2 TRACK/SS1 TRACK/SS2 PG1 PG2 GND R6 47k R8 33.2k fSW = 1MHz R4 15.0k C5 47μF R7 100k RT/SYNC C10 0.047μF C1 TO C6: X5R OR X7R D1, D2: MMSD4148 D3: DIODES INC. B140 D4: DIODES INC. B120 OUT2 1.8V 1.4A SW2 FB1 R3 10k L2 3.3μH C7 330pF 3508 TA05 POWER GOOD RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1765 25V, 2.75A (IOUT), 1.25MHz, High Efficiency Step-Down DC/DC Converter VIN: 3V to 25V, VOUT(MIN) = 1.2V, IQ = 1mA, S8, TSSOP16E Packages LT1766 60V, 1.2A (IOUT), 200kHz, High Efficiency Step-Down DC/DC Converter VIN: 5.5V to 60V, VOUT(MIN) = 1.2V, IQ = 2.5mA, TSSOP16/TSSOP16E Packages LT1767 25V, 1.2A (IOUT), 1.25MHz, High Efficiency Step-Down DC/DC Converter VIN: 3V to 25V, VOUT(MIN) = 1.2V, IQ = 1mA, MS8, MS8E Packages LT1940/LT1940L Dual Monolithic 1.4A, 1.1MHz Step-Down Switching Regulators VIN: 3.6V to 25V, VOUT(MIN) = 1.25V, IQ = 3.8mA, TSSOP16E Packages LTC3407 Dual 600mA, 1.5MHz, Synchronous Step-Down Regulator VIN: 2.5V to 5.5V, VOUT(MIN) = 0.6V, IQ = 40μA, MSE Package LT3493 1.2A, 750kHz Step-Down Switching Regulator in 2mm × 3mm DFN VIN: 3.6V to 36V, VOUT(MIN) = 0.78V, IQ = 1.9mA, 2mm × 3mm DFN Package LT3501/LT3510 Dual 3A/2A, 1.5MHz High Efficiency Step-Down Switching Regulators VIN: 3.6V to 25V, VOUT(MIN) = 0.8V, IQ = 3.7mA, ISD < 10μA, TSSOP20E Package LT3506/LT3506A Dual Monolithic 1.6A, 1.1MHz Step-Down Switching Regulators VIN: 3.6V to 25V, VOUT(MIN) = 0.8V, IQ = 3.8mA, 16-Lead DFN and 16-Lead TSSOPE Packages LTC3701 Two Phase, Dual, 500kHz, Constant Frequency, Current Mode, High Efficiency Step-Down DC/DC Controller VIN: 2.5V to 10V, VOUT(MIN) = 0.8V, IQ = 460μA, SSOP-16 Package LTC3736 Dual Two Phase, No RSENSE™, Synchronous Controller with Output Tracking VIN: 2.75V to 9.8V, VOUT(MIN) = 0.6V, IQ = 300μA, 4mm × 4mm QFN or SSOP-24 Packages LTC3737 Dual Two Phase, No RSENSE DC/DC Controller with Output Tracking VIN: 2.75V to 9.8V, VOUT(MIN) = 0.6V, IQ = 220μA, 4mm × 4mm QFN or SSOP-24 Packages No RSENSE is a trademark of Linear Technology Corporation. 3508fb 24 Linear Technology Corporation LT 0208 REV B • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2007