EL5106, EL5306 ® Data Sheet November 3, 2005 FN7357.4 350MHz Fixed Gain Amplifiers with Enable Features The EL5106 and EL5306 are fixed gain amplifiers with a bandwidth of 350MHz. This makes these amplifiers ideal for today’s high speed video and monitor applications. They feature internal gain setting resistors and can be configured in a gain of +1, -1 or +2. • Pb-free plus anneal available (RoHS compliant) With a supply current of just 1.5mA and the ability to run from a single supply voltage from 5V to 12V, these amplifiers are also ideal for handheld, portable or battery powered equipment. • Fast enable/disable The EL5106 and EL5306 also incorporate an enable and disable function to reduce the supply current to 25µA typical per amplifier. Allowing the CE pin to float or applying a low logic level will enable the amplifier. • 450MHz, 3.5mA product available (EL5108 & EL5308) The EL5106 is offered in the 6 Ld SOT-23 and the industrystandard 8 Ld SO packages and the EL5306 is available in the 16 Ld SO and 16 Ld QSOP packages. All operate over the industrial temperature range of -40°C to +85°C. • Handheld, portable devices • Gain selectable (+1, -1, +2) • 350MHz -3dB BW (AV = 2) • 1.5mA supply current per amplifier • Single and dual supply operation, from 5V to 12V • Available in SOT-23 packages Applications • Battery powered equipment • Video amplifiers • Cable drivers • RGB amplifiers Ordering Information (Continued) Ordering Information PART TAPE & PART NUMBER MARKING REEL PACKAGE PKG. DWG. # PART TAPE & PART NUMBER MARKING REEL PACKAGE PKG. DWG. # EL5306ISZ (See Note) EL5306ISZ - 16 Ld SO (0.150”) (Pb-free) MDP0027 EL5306ISZ-T7 (See Note) EL5306ISZ 7” 16 Ld SO (0.150”) (Pb-free) MDP0027 MDP0038 EL5306ISZ-T13 EL5306ISZ (See Note) 13” 16 Ld SO (0.150”) (Pb-free) MDP0027 EL5106IW-T7 t 7” 6 Ld SOT-23 (3K pcs) MDP0038 EL5106IW-T7A t 7” 6 Ld SOT-23 (250 pcs) MDP0038 EL5106IWZ-T7 (See Note) BAFA 7” 6 Ld SOT-23 (3K pcs) (Pb-free) MDP0038 EL5106IWZ-T7A BAFA (See Note) 7” 6 Ld SOT-23 (250 pcs) (Pb-free) EL5106IS 5106IS - 8 Ld SO MDP0027 EL5306IU 5306IU - 16 Ld QSOP MDP0040 EL5106IS-T7 5106IS 7” 8 Ld SO MDP0027 EL5306IU-T7 5306IU 7” 16 Ld QSOP MDP0040 EL5106IS-T13 5106IS 13” 8 Ld SO MDP0027 EL5306IU-T13 5306IU 13” 16 Ld QSOP MDP0040 EL5106ISZ (See Note) 5106ISZ - 8 Ld SO (Pb-free) MDP0027 EL5306IUZ (See Note) 5306IUZ - 16 Ld QSOP (Pb-free) MDP0040 EL5106ISZ-T7 (See Note) 5106ISZ 7” 8 Ld SO (Pb-free) MDP0027 EL5306IUZ-T7 (See Note) 5306IUZ 7” 16 Ld QSOP (Pb-free) MDP0040 EL5106ISZ-T13 5106ISZ (See Note) 13” 8 Ld SO (Pb-free) MDP0027 EL5306IUZ-T13 5306IUZ (See Note) 13” 16 Ld QSOP (Pb-free) MDP0040 NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. EL5306IS EL5306IS - 16 Ld SO (0.150”) MDP0027 EL5306IS-T7 EL5306IS 7” 16 Ld SO (0.150”) MDP0027 EL5306IS-T13 EL5306IS 13” 16 Ld SO (0.150”) MDP0027 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2002-2005. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. EL5106, EL5306 Pinouts EL5306 (16 LD SO, QSOP) TOP VIEW EL5106 (8 LD SO) TOP VIEW NC 1 IN- 2 + IN+ 3 VS- 4 8 CE INA+ 1 7 VS+ CEA 2 6 OUT VS- 3 5 NC CEB 4 16 INA+ 14 VS+ + - INB+ 5 EL5106 (6 LD SOT-23) TOP VIEW OUT 1 VS- 2 6 VS+ 5 CE + - IN+ 3 4 IN- 2 INC+ 8 13 OUTB 12 INB- NC 6 CEC 7 15 OUTA 11 NC + - 10 OUTC 9 INC- EL5106, EL5306 Absolute Maximum Ratings (TA = 25°C) Supply Voltage between VS+ and VS- . . . . . . . . . . . . . . . . . . . 13.2V Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 50mA Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 125°C Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves Pin Voltages. . . . . . . . . . . . . . . . . . . . . . . . . VS- -0.5V to VS+ +0.5V Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications PARAMETER VS+ = +5V, VS- = -5V, RL = 150Ω, TA = 25°C unless otherwise specified. DESCRIPTION CONDITIONS MIN TYP MAX UNIT AC PERFORMANCE BW -3dB Bandwidth AV = +1 250 MHz AV = -1 380 MHz AV = +2 350 MHz 20 MHz 4500 V/µs 16 ns 2.8 nV/√Hz 6 pA/√Hz BW1 0.1dB Bandwidth SR Slew Rate VO = -2.5V to +2.5V, AV = +2 tS 0.1% Settling Time VOUT = -2.5V to +2.5V, AV = 2 eN Input Voltage Noise iN+ IN+ Input Current Noise dG Differential Gain Error (Note 1) AV = +2 0.02 % dP Differential Phase Error (Note 1) AV = +2 0.04 ° 3000 DC PERFORMANCE VOS Offset Voltage TCVOS Input Offset Voltage Temperature Coefficient Measured from TMIN to TMAX 5 AE Gain Error VO = -3V to +3V, RL = 150Ω 1 RF, RG Internal RF and RG -10 1 10 mV µV/°C 2.5 % 325 Ω ±3.3 V INPUT CHARACTERISTICS CMIR Common Mode Input Range +IIN + Input Current RIN Input Resistance CIN Input Capacitance ±3 1.5 at IN+ 7 µA 2 MΩ 1 pF OUTPUT CHARACTERISTICS VO RL = 150Ω to GND ±3.4 ±3.6 V RL = 1kΩ to GND ±3.7 ±3.85 V Output Current RL = 10Ω to GND 60 100 mA ISON Supply Current - Enabled (per amplifier) No load, VIN = 0V 1.35 1.5 1.82 mA ISOFF Supply Current - Disabled (per amplifier) No load, VIN = 0V 12 25 µA PSRR Power Supply Rejection Ratio 75 dB 280 ns IOUT Output Voltage Swing SUPPLY DC, VS = ±4.75V to ±5.25V ENABLE tEN Enable Time 3 EL5106, EL5306 Electrical Specifications PARAMETER VS+ = +5V, VS- = -5V, RL = 150Ω, TA = 25°C unless otherwise specified. (Continued) DESCRIPTION CONDITIONS MIN TYP MAX 400 UNIT tDIS Disable Time ns IIHCE CE Pin Input High Current CE = VS+ 1 5 25 µA IILCE CE Pin Input Low Current CE = VS- +1 0 -1 µA VIHCE CE Input High Voltage for Power-down VILCE CE Input Low Voltage for Enable VS+ -1 V VS+ -3 V NOTE: 1. Standard NTSC test, AC signal amplitude = 286mVP-P, f = 3.58MHz Pin Descriptions EL5106 (SO8) EL5106 (SOT23-6) 1, 5 2 4 EL5306 (SO16, QSOP16) PIN NAME 6, 11 NC Not connected 9, 12, 16 IN- Inverting input FUNCTION EQUIVALENT CIRCUIT RG IN+ IN- RF CIRCUIT 1 3 3 1, 5, 8 IN+ Non-inverting input 4 2 3 VS- Negative supply 6 1 10, 13, 15 OUT Output (Reference Circuit 1) OUT RF CIRCUIT 2 7 6 14 VS+ Positive supply 8 5 2, 4, 7 CE Chip enable VS+ CE VSCIRCUIT 3 4 EL5106, EL5306 Typical Performance Curves 11 VS=±5V RL=150Ω 3 9 1 GAIN (dB) NORMALIZED GAIN (dB) 5 AV = -1 -1 AV = 2 -5 100K 1M 10M 100M CL = 10pF CL = 6.8pF 7 CL = 2.2pF 5 CL = 0pF AV = 1 -3 AV=+2 VS=±5V RL=150Ω 3 1 100K 1G 1M FREQUENCY (Hz) FIGURE 1. FREQUENCY RESPONSE 1.6 1G 100M FIGURE 2. FREQUENCY RESPONSE FOR VARIOUS CL 450 RL = 150Ω 10M FREQUENCY (Hz) AV = -1 RL = 150Ω 350 AV = 1, 2 BW (MHz) DELAY TIME (ns) AV = -1 1.2 0.8 AV = 2 250 AV = 1 0.4 0 1 10 100 150 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 1K FREQUENCY (Hz) FREQUENCY (Hz) FIGURE 3. GROUP DELAY vs FREQUENCY 1 FIGURE 4. BANDWIDTH vs SUPPLY VOLTAGE 0 RL = 150Ω AV = -1 0.6 AV = 2 0.4 AV = 1 0.2 -20 PSRR (dB) PEAKING (dB) -10 0.8 -30 PSRR+ PSRR- -40 -50 -60 -70 0 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 VS (V) FIGURE 5. PEAKING vs SUPPLY VOLTAGE 5 -80 1K 10K 100K 1M 10M FREQUENCY (Hz) FIGURE 6. POWER SUPPLY REJECTION RATIO vs FREQUENCY 100M EL5106, EL5306 Typical Performance Curves (Continued) 1.6 100 1.55 IS (mA) IMPEDANCE (Ω) 1.5 10 IS- 1.45 IS+ 1.4 1.35 1 1.3 1.25 0.1 10K 100K 1M 1.2 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 100M 10M VS (V) FREQUENCY (Hz) FIGURE 7. OUTPUT IMPEDANCE vs FREQUENCY 0 VS=±5V AV=2 RL=150Ω VOP-P=2V -10 -20 DISTORTION (dB) FIGURE 8. SUPPLY CURRENT vs SUPPLY VOLTAGE (PER AMPLIFIER) M=100ns -30 -40 CH1 2.00V/DIV HD3 -50 -60 HD2 -70 CH2 1.00V/DIV -80 -90 0 10 20 30 40 50 60 FREQUENCY (MHz) FIGURE 9. HARMONIC DISTORTION vs FREQUENCY FIGURE 10. ENABLED RESPONSE JEDEC JESD51-3 LOW EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 1 CH1 2.00V/DIV CH2 1.00V/DIV POWER DISSIPATION (W) M=100ns 909mW 0.9 SO16 (0.150”) θJA=110°C/W 0.8 0.7 625mW 0.6 633mW SO8 θJA=160°C/W 0.5 0.4 391mW 0.3 SOT23-6 θJA=256°C/W 0.2 QSOP16 θJA=158°C/W 0.1 0 0 25 50 75 85 100 125 150 AMBIENT TEMPERATURE (°C) FIGURE 11. DISABLED RESPONSE 6 FIGURE 12. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE EL5106, EL5306 Typical Performance Curves (Continued) JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD POWER DISSIPATION (W) 1.4 1.250W 1.2 SO16 (0.150”) θJA=80°C/W 1 909mW 0.8 893mW SO8 θJA=110°C/W 0.6 435mW 0.4 SOT23-6 θJA=230°C/W 0.2 0.1 0 0 25 50 QSOP16 θJA=112°C/W 75 85 100 125 150 AMBIENT TEMPERATURE (°C) FIGURE 13. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE Applications Information Product Description The EL5106 and EL5306 are fixed gain amplifier that offers a wide -3dB bandwidth of 350MHz and a low supply current of 1.5mA. They work with supply voltages ranging from a single 5V to 12V and they are also capable of swinging to within 1.2V of either supply on the output. These combinations of high bandwidth and low power make the EL5106 and EL5306 the ideal choice for many lowpower/high-bandwidth applications such as portable, handheld, or battery-powered equipment. For varying bandwidth and higher gains, consider the EL5191 with 1GHz on a 9mA supply current or the EL5162 with 300MHz on a 4mA supply current. Versions include single, dual, and triple amp packages with 5 Ld SOT-23, 16-pin QSOP, and 8 Ld or 16 Ld SO outlines. Power Supply Bypassing and Printed Circuit Board Layout As with any high frequency device, good printed circuit board layout is necessary for optimum performance. Low impedance ground plane construction is essential. Surface mount components are recommended, but if leaded components are used, lead lengths should be as short as possible. The power supply pins must be well bypassed to reduce the risk of oscillation. The combination of a 4.7µF tantalum capacitor in parallel with a 0.01µF capacitor has been shown to work well when placed at each supply pin. enabled by floating or pulling the CE pin to at least 3V below the positive supply. For ±5V supply, this means that the amplifier will be enabled when CE is 2V or less, and disabled when CE is above 4V. Although the logic levels are not standard TTL, this choice of logic voltages allow the EL5106 and EL5306 to be enabled by tying CE to ground, even in 5V single supply applications. The CE pin can be driven from CMOS outputs. Gain Setting The EL5106 and EL5306 are built with internal feedback and gain resistors. The internal feedback resistors have equal value; as a result, the amplifier can be configured into gain of +1, -1, and +2 without any external resistors. Figure 13 shows the amplifier in gain of +2 configuration. The gain error is ±2% maximum. Figure 14 shows the amplifier in gain of -1 configuration. For gain of +1, IN+ and IN- should be connected together as shown in Figure 15. This configuration avoids the effects of any parasitic capacitance on the IN- pin. Since the internal feedback and gain resistors change with temperature and process, external resistor should not be used to adjust the gain settings. 325Ω 325Ω IN- IN+ + FIGURE 14. AV = +2 Disable/Power-Down The EL5106 and EL5306 amplifiers can be disabled placing their output in a high impedance state. When disabled, the amplifier supply current is reduced to <25µA. The EL5106 and EL5306 are disabled when its CE pin is pulled up to within 1V of the positive supply. Similarly, the amplifier is 7 EL5106, EL5306 325Ω 325Ω 325Ω IN- +5 IN+ + 325Ω FIGURE 15. AV = -1 +5 0.1µF + VOUT 1K 325Ω 0.1µF IN- 325Ω VIN - 1K + IN+ FIGURE 17. FIGURE 16. AV = +1 Supply Voltage Range and Single-Supply Operation The EL5106 and EL5306 have been designed to operate with supply voltages having a span of greater than or equal to 5V and less than 11V. In practical terms, this means that the EL5106 and EL5306 will operate on dual supplies ranging from ±2.5V to ±5V. With single-supply, the EL5106 and EL5306 will operate from 5V to 10V. As supply voltages continue to decrease, it becomes necessary to provide input and output voltage ranges that can get as close as possible to the supply voltages. The EL5106 and EL5306 have an input range which extends to within 2V of either supply. So, for example, on ±5V supplies, the EL5106 and EL5306 have an input range which spans ±3V. The output range is also quite large, extending to within 1V of the supply rail. On a ±5V supply, the output is therefore capable of swinging from -4V to +4V. Single-supply output range is larger because of the increased negative swing due to the external pull-down resistor to ground. Figure 16 shows an AC-coupled, gain of +2, +5V single supply circuit configuration. 8 Video Performance For good video performance, an amplifier is required to maintain the same output impedance and the same frequency response as DC levels are changed at the output. This is especially difficult when driving a standard video load of 150Ω, because of the change in output current with DC level. Previously, good differential gain could only be achieved by running high idle currents through the output transistors (to reduce variations in output impedance). Special circuitries have been incorporated in the EL5106 and EL5306 to reduce the variation of output impedance with current output. This results in dG and dP specifications of 0.02% and 0.04°, while driving 150Ω at a gain of 2. Output Drive Capability In spite of its low 1.5mA of supply current per amplifier, the EL5106 and EL5306 are capable of providing a maximum of ±125mA of output current. Driving Cables and Capacitive Loads When used as a cable driver, double termination is always recommended for reflection-free performance. For those applications, the back-termination series resistor will decouple the EL5106 and EL5306 from the cable and allow extensive capacitive drive. However, other applications may have high capacitive loads without a back-termination resistor. In these applications, a small series resistor (usually between 5Ω and 50Ω) can be placed in series with the output to eliminate most peaking. EL5106, EL5306 where: Current Limiting The EL5106 and EL5306 have no internal current-limiting circuitry. If the output is shorted, it is possible to exceed the Absolute Maximum Rating for output current or power dissipation, potentially resulting in the destruction of the device. θJA = Thermal resistance of the package Power Dissipation PDMAX = Maximum power dissipation of each amplifier in the package With the high output drive capability of the EL5106 and EL5306, it is possible to exceed the 125°C Absolute Maximum junction temperature under certain very high load current conditions. Generally speaking when RL falls below about 25Ω, it is important to calculate the maximum junction temperature (TJMAX) for the application to determine if power supply voltages, load conditions, or package type need to be modified for the EL5106 and EL5306 to remain in the safe operating area. These parameters are calculated as follows: T JMAX = T MAX + ( θ JA × n × PD MAX ) TMAX = Maximum ambient temperature n = Number of amplifiers in the package PDMAX for each amplifier can be calculated as follows: V OUTMAX PD MAX = ( 2 × V S × I SMAX ) + ( V S - V OUTMAX ) × ---------------------------R L where: VS = Supply voltage ISMAX = Maximum bias supply current VOUTMAX = Maximum output voltage (required) RL = Load resistance SO Package Outline Drawing 9 EL5106, EL5306 SOT-23 Package Outline Drawing 10 EL5106, EL5306 QSOP Package Outline Drawing NOTE: The package drawings shown here may not be the latest versions. To check the latest revision, please refer to the Intersil website at http://www.intersil.com/design/packages/index.asp All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 11